Search Documents

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered feed samples in a larger KC as op-posed to the commonly adopted GRG test has been discussed.

Jan 1, 2014

By Kazutoshi Haga, Atsushi Shibayama, Kosuke Nishioka, Yasushi Kihara, Altansukh Batnasan

The aim of this study was to investigate the feasibility studies of seawater in flotation of a 1.5 mass % of copper containing copper sulfide ore. Effects of seawater, various frothers, and different distilled water/seawater ratio on flotation of copper sulfide ore were studied. Surface properties of native copper ore and sea water soaked were examined by using FT-IR spectrometry. Chemical contents of the copper sulfide ore and after flotation were identified using XRD studies. XRD pattern showed that the main constituents of the copper sulfide ore are chalcopyrite (CuFeS2), bornite (Cu5FeS4). Flotation experiments were carried out using mechanical agitation flotation equipment with a mineral separation type flotation cell. Froth flotation experiment was conducted using calcium hydroxide was used as a pH adjuster, using methyl isobutyl carbinol (MIBC), dow froth 250 (DF 250) as frothers and potassium amyl xanthate (PAX) as collector for the copper recovery from the copper sulfide ore containing chalcopyrite and bornite. The results showed that the copper recovery by flotation was dependent on the flotation medium and frother. The main results showed that the copper recovery by flotation was dependent on the process water and frother. The copper recovery reached 97 % and 87 % in the distilled water flotation and seawater flotation with MIBC, respectively. For seawater flotation with DF 250, the Cu recovery achieved near 95 % and grade of Cu in the froth product after 5 min flotation was reached 29.8 mass %.

Jan 1, 2014

By F. K. Ikumapayi

An approach to environmental sustainability and improved process economy, in sulphide minerals production is recycling of process water in flotation of complex sulphide ores, although the chemistry of process water may be a critical issue to flotation efficiency. The influence of major components of calcium and sulphate ions in process water on xanthate collector adsorption and flotation response using pure chalcopyrite, galena and sphalerite minerals were investigated by Hallimond flotation, zeta-potential measurement, FTIR and XPS spectroscopy studies, while bench scale flotation tests were also carried out using complex sulphide ores. The impact of the species in flotation was comprehended using deionised water, tap water, process water and simulated water containing equivalent amount of calcium and sulphate species in process water. Hallimond flotation results showed a decrease of chalcopyrite and galena recovery in process water and also in the presence of calcium and sulphate ions in both deionised and process waters, whereas sphalerite does not respond to flotation. The adsorption of calcium and metal ions but not sulphate ions on the minerals is evidenced by zeta-potential data. FTIR and XPS studies revealed the presence of surface oxidized sulfoxy species and surface calcium carbonates on chalcopyrite in the presence of process water and water containing calcium ions, surface oxidized sulfoxy and carbonate species on galena in the presence of deionised water, process water and water containing calcium and sulphate ions, all at flotation pH 10.5, and these surface species influenced xanthate adsorption. The presence of surface oxidized sulfoxy and carbonate species at the sphalerite flotation pH 11.5 were seen in the presence of deionised water, process water and water containing calcium and sulphate ions, but the surface species does not influence xanthate adsorption. Bench scale flotation using two different complex sulphide ores showed that chalcopyrite, galena and sphalerite recoveries are better in process water than tap water. The studies showed that the process water can be recycled in flotation with no detrimental effect on grade and recovery of sulphide minerals. Keywords: sulphide minerals, flotation, zeta-potential, FTIR, XPS

Sep 1, 2012

By Y. S. Sun, P. Gao

"In this investigation, a pilot-scale suspension magnetization roasting reactor was introduced and used to enhance magnetic properties of an iron ore. Consequently, the effects of roasting temperature, reducing gas CO flow rate and fluidizing gas N2 flow rate on the magnetization roasting performance were investigated. The results indicate that the hematite and siderite are almost completely converted into magnetite by a gas mixture of 3.5 Nm3/h CO and 2 Nm3/h N2 at roasting temperature of 520 °C. Under the optimized conditions, the magnetic iron concentrate with an iron grade of 60.18% and iron recovery of 90.17% was achieved. The XRD and Fe mineral phase analyses revealed that most of the hematite and siderite were converted to magnetite, and the magnetic properties were greatly enhanced. INTRODUCTION The steel and iron industry in China has rapidly developed in recent years requiring a large quantity of iron ores. Low-grade and complex iron ores are currently the overwhelmingly dominant mineral resource for iron in China. Therefore, China depends on imported iron ore resources heavily, resulting in an increase in the production costs of iron-making and steel-making[1-3]. Using domestic resources to produce a steady supply of high-quality iron ores is an important step toward the sustainable development of the steel and iron industry[4-5]. The iron ore from Jiuquan iron and steel company is abundant and recognized as typically complex iron ore resources in China. Magnetization roasting followed by low-intensity magnetic separation has been proven as the most feasible methods to upgrade refractory iron ore[6-10]. In present research, an innovative roasting technology, namely suspension magnetization roasting, was developed and applied to recover iron from a typical refractory iron ore. Suspension magnetization roasting technique and equipment developed by Prof. Yuexin Han’s Group at Northeastern University (NEU) is an effective way for the utilization of refractory iron ore. The advent of suspension magnetization roasting will, in China and even globally, produce a significant technological revolution in the field of iron ore beneficiation. Based on the previous works, this paper mainly described experiments on the separation and recovery of iron from a complex refractory iron ore by means of suspension magnetizing roasting and low-intensity magnetic separation processes. The purpose of the research is providing a new technology for effective utilization of refractory iron ore. Process parameters that affected the separation and recovery rate of iron were conducted and optimized, and the reaction process was analyzed by XRD and Fe mineral phase analysis."

Jan 1, 2018

By R. ?. Sherembayeva, ?. ?. ?uktybayeva, ?. B. Rakhimbekova, N. ?. ?m?rova

"Studying the interaction of the phosphorus-containing flotation reagent with the components of the flotation system ""liquid-gas-solid"" during flotation of non-ferrous metal ores allows regulating the enrichment process. The phosphorus-containing reagent-collector anabasinium-O,O-dimethyl-thiophosphate has beensynthesized under laboratory conditions and the concentrated aqueous solution of anabasin hydrochloride and the 40% solution of sodium hydroxide have been used as the raw material. The phosphorus-containing reagent has been obtained by interaction of the anabasine base, sulfur and dimethyl phosphite, due to sulfur and nitrogen atoms it can form complex compounds with heavy metal ions.Studying flotation of copper-sulfide ore of the Sayak field with the use of the phosphorus-containing reagent-collector anabasinium has been performed in the open and closed cycles. The degree of ore grinding was 60- 62% of the class -0.074 mm. There has been established the dependence of the ore flotation parameters on: a) pH of the pulp; b) the consumption of the reagent-collector anabasinium.The effect of the pulp pH on the technological parameters of copper ore flotation has been carried out with a reagent regulator that increases the difference in the surface properties of the minerals to be separated.There has been used lime as the regulator of the medium, the consumption of which varied from 750 to 1500 g/t; the consumption of the reagent-collector anabasinium was 10, 15, 20 and 25 g/t.It has been found that when flotation of copper ore without the use of lime at pH equal to 7.8 and at the reagent consumption, g/t: anabasinium - 25, T-92 - 55, copper recovery in the concentrate is 92.72%, the quality of concentrate is 7, 1%.In flotation according to the factory mode (the consumption of xanthate is 44 g/t, T-92 is 55 g/t, pH = 7.8 (without lime)) of copper ore, copper recovery in the concentrate is 87.38%, the concentrate quality is 7, 97%, with reducing the xanthate consumption to 25 g/t copper recovery is reduced to 83.39%, the quality of the concentrate is up to 6.69%.In the experiments using the factory reagent mode in the closed cycle, with the xanthate mass consumption of 44 g/t, T-92 blowing agent of 55 g/t, the third recleaning concentrate contained 19.13% copper with recovery of 86.89%.Using a phosphorus-containing reagent instead of xanthate with the same flow rate, the third recleaning concentrate with the mass fraction of copper of 19.82% has beenobtained with recovery of 87.77%."

Jan 1, 2018

By I. Gombköto, G. Mucsi, S. Nagy, F. Kristály, Á. Rácz, R. Szabó, B. Egyed

"Present paper deals with the investigation of a Hungarian pumice. Grinding experiments were carried out in a stirred media mill for various residence time. Ground samples were tested with laser particle size analyzer to determine and calculate the material fineness (particle size distribution and specific surface area). The lime adsorption capacity was measured to monitor the reactivity. Alkali activated cement paste was prepared using ground pumice with various alkali activators. Cube shaped specimens were produced from the paste and the uniaxial compressive strength was measured at the age of 7 days. The resulted alkali activated material structure was investigated by XRD and FTIR. The results of the experiments show that pumice fineness has strong impact on its hydraulic activity, hence on the compressive strength and the structure of the resulted binder. Relationships between grinding fineness, material structure and strength of the raw and mechanical activated material as well as the alkali activated cement were revealed. INTRODUCTION Pumice is a natural pozzolan which can be used as raw material for cementitious materials in limited portion owing to its low reactivity. Furthermore, due to its mineralogical composition it can be used for developing a new environmental friendly binder, namely alkali activated cements (AAC) which are inorganic alumina-silicate materials with good cementitious properties (Almalkawi et al., 2017; Özodabas and Yilmaz, 2013; Najimi et al. 2018; Yadollahi et al., 2015). Despite being a rather recent research topic, many papers and books have been published focusing on various aspects of alkali activation. There is great variety of raw materials that can be utilized for AAC production. However, primary raw materials are very expensive and secondary materials are heterogenous in composition. Therefore, a more homogeneous and low price silicate would help to balance the properties and cost of resulting cement and easing the way for commercialization of AAC. However, the control of its reactivity is of great importance which can be realized using mechanical activation by grinding (Juhász and Opoczky, 1990; Djobo et al., 2016; Mádai et al., 2015). The goal of present paper is to investigate the effect of mechanical activation of pumice on the properties of the resulted alkali activated cement."

Jan 1, 2018

By Vinay Jain, Dharmendr Kumar, Beena Rai, Venugopal Tammishetti

"Selective dispersion-flocculation is considered to be an effective process for the beneficiation of ultrafine particles. This process is based on the preferential adsorption of a flocculant on the mineral particles to be flocculated, leaving rest of the mineral suspended. It has been successfully implemented at plant scales for the beneficiation of ultrafine particles of iron ores, for which conventional methods such as gravity separation, magnetic separation and flotation do not work efficiently. However, the key element responsible for the success of any selective flocculation process is the appropriate choice of the flocculant used for achieving the desired selectivity. At our lab, we are working on design and development of such selective reagents for mineral processing applications, including the beneficiation of iron ore slimes, using a combined molecular modeling and experimental approach. In this study we have employed density functional theory (DFT) to calculate the interaction energies and explain the interaction mechanisms of chitosan with the main minerals present in iron ore slimes, namely, hematite [a-Fe2O3], goethite [a-FeO(OH)], gibbsite [a-Al(OH)3] and kaolinite [Al2Si2O5(OH)4]. The magnitudes of the computed interaction energies follow the trend: Hematite > Goethite > Gibbsite ~ Kaolinite Al-OH terminated > Kaolinite Si-O terminated Analysis of the optimized geometries and electronic structures reveals that the O & N atoms of chitosan molecule form coordinate bonds with surface Fe-atoms of hematite while only weak hydrogen bonds are formed in the case of goethite, gibbsite and kaolinite surfaces thus explaining reasons behind the stronger interactions with the hematite surface. The theoretical findings were validated by performing selective flocculation experiments using chitosan as a flocculant. The selective flocculation experimental results show that a final concentrate of ~60% Fe can be obtained from a feed containing 53.13% Fe with Fe recovery of 74%. The mineral estimation in the obtained concentrate indicated that hematite and goethite are recovered in concentrate while gibbsite and kaolinite are rejected in the tails. These observations were consistent with our theoretical findings. Our work highlights the promising role molecular modeling techniques such as DFT can play in the design and development of selective reagents for beneficiation of alumina-rich iron ore slimes."

Jan 1, 2018

By X. H. Li, F. Xie, Q. Zhang, Z. H. Shen, S. Mao

"There is abundant rare-earth element(REE) in our country, but it is very fragmented in the earth's crust, and it is very difficult to mining or mining cost is extremely high. There are few of industrial value rare-earth deposits. There is a lot of concomitant rare-earth deposits, and the comprehensive utilization value is high. There is very rich carlin-type gold resource, associated with a certain amount of REE in the southwest of Guizhou province. In order toutilize comprehensively the resources, this paper conducts the study on the occurrence characteristics of REE in the ore. By the chemical analysis, the gold grade is 3.35g/t, the organic carbon 0.81%, the total REE 0.022%, which is a high carbon fine disseminated gold ore. By the optical microscope and XRD analysis, the major minerals are quartz, pyrite, calcite, limonite, arsenopyrite, mica, kaolinite, clay minerals, etc. In addition, there is a large amount of carbonaceous materials, such as organic carbon, graphite, which is harmful on leaching of gold. By the scanning electron microscopy analysis, there are thorium, lanthanum and neodymium, ytterbium, persimmon and other REE in the ore. Gravity separation shows that REE could be enriched to lighter material mainly, which indicates that REE disseminate closely with lighter materials.INTRODUCTION Carlin-type gold ore is important gold resource in the world, which are mainly distributed in Nevada and its vicinity, as well as the two Golden Triangle of Yunnan, Guizhou, Guangxi and Sichuan, Shanxi, Gansu province in China(Su W.C. et al.,2009; Xia G.X.,1996).Guizhou carlin-type gold ore is the second largest gold resource in the world(Muntean J L et al.,2011), distributing along the southwestern margin of the Yangtze plate, mainly mineralizing in the neopaleozoic-early mesozoic(Xie Z J et al.,2017). Many large gold deposits have been found in southwest in Guizhou in twentieth century, such as Zimuyou,Getang, Lannigou, Shuiyindong and Laowanchang gold deposit, and so on, and the gold reserves reach over 100 tons(Xia Y. et al.,2009).There is a certain amount of rare-earth resource in the carlin-type gold ore in the southwest in Guizhou province, and the current researches might mainly focus on characteristics of REE from the angle of geological mineralization(AnanyevY.,2015), not from the angle of separation and enrichment."

Jan 1, 2018

By Z. G. Song, C. Y. Sun, X. R. Zhang, Y. Yu

In skarn type scheelite deposit, there are calcium minerals with floatability similar to scheelite, such as calcite, fluorite, etc., which are difficult to separate. Heating cleaning method developed by Petrov has been widely applied in processing rough concentrate of scheelite for nearly half a century, but there exists a general lack of full understanding of the interaction between floatation reagent and mineral particles surfaces. The mechanism on separation of scheelite and calcium minerals in heating cleaning process was investigated by mineral flotation experiments, XPS analysis, as well as solution chemistry and crystal chemistry calculations. The results showed that the sequence of minerals floatability using sodium oleate as collector and a large amount of sodium silicate as modifier in heating flotation test was scheelite > calcite > fluorite, which was the same as solution chemistry calculations based on Gibbs free energy vs. pH and also the same as Ca-X intensity order by crystal chemistry analysis. There are two sides about the mechanism of heating cleaning method: one is that the adsorbed collector on calcium minerals surface is desorbed more easily than scheelite, and the other is selective dissolution of calcium ions from the mineral surface because of Ca-X intensity difference in heating and stirring process.

Jan 1, 2014

By G. Jenny

The particle size distribution of ground minerals is of decisive importance for downstream processes like floatation, separation, drying or others. In order to optimize the process efficiency on one hand and the final product quality on the other hand an early control of the grinding or classification stage is essential. The ultrasound based particle size analyser OPUS is capable of performing on-line particle size distribution (PSD) and solid content measurement of mineral slurries such as iron ore, copper ore, fluorspar, or quartz sand and alumina directly in heavy and rough process environment. The instrument provides a PSD of 31 size classes and can be applied for particles from nanometer range up to several millimetres. Arbitrary interpolations in between the 31 measured points are available. Typical residue values show an excellent agreement to off-line particle size analysis methods such as e.g. sieve analyses or laser diffraction. OPUS is designed as rugged in-line probe made from stainless steel. The applied technique is independent of product flow dynamics, contamination, optical properties, vibrations, pressures or changes in solid concentrations. The instrument provides all data on the system?s PC or on the process control system by a variety of interfaces.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, A. Dehghani Ahmadabadi, M. Zare

"In the most iron ore beneficiation plants, reverse flotation is the best method for removing silicate gangues from final iron ore concentrate. Many previous studies show, if the major portion of impurities include quartz minerals, the flotation process is simple, but if iron silicates are dominant, reverse flotation is so complicated and mostly not very effective. In this study which was performed on the Sangan iron ore concentrate, the performance using of reverse flotation and magnetic flotation separator for elimination of silicate gangues from the magnetic iron concentrate was investigated. The operational parameters for reverse flotation are considered as: collector and frother types and dosages and also modifiers. But for magnetic flotation separator parameters were magnetic field intensity as well as overflow and underflow water rates. Results showed that reverse flotation has not a significant effect on the elimination of impurities. Because of the silicate gangues of Sangan concentrate including a mixture of quartz and iron silicates (amphibole, pyroxene and feldspar), so downgrading of the SiO2 content for the flotation concentrate was rather low and only average reduces of 20.60% were possible. But the findings of using magnetic separator was more satisfactory. Results of the weight recovery, iron grade and also SiO2 and S grades of final concentrate were better with magnetic flotation device. So at the best and optimum condition, we could reduce 51.01% of the total silicate (SiO2~ 2.19%) along with 74.66% of sulfur content (S~ 0.076%) and concentrate weight and Fe recoveries of 92.04% and 94.51% respectively, final Fe grade of 68.73%.INTRODUCTION Chemical/traditional flotation is one of the most effective methods for separating valuable particles from waste minerals, which is used in most mineral processing industries. In the iron ore processing industry, the major impurities present in iron ore concentrate include sulfur, silica and phosphorus (Bruckard et al, 2015), which are often carried out by reverse flotation methods for the removal of sulfide and oxide impurities (Donald, 1967: Araujo et al., 2005: Ma, 2012)"

Jan 1, 2018

By G. Rajesh

Mathematical modeling of bioremediation has gained importance as it is used as an optimization tool for the remediation process involved in contaminated sites. The bioremediation of Cr(VI) has been studied taking into consideration the initial Cr(VI) concentration Cr(VI)ini, bacterial growth substrate concentration (S), maximum growth rate (µmax), yield coefficient (Y), half saturation constant (Ks), and inhibition constant (KI). As the enzymatic reaction is also affected by initial substrate concentration (Sini) and Ks, different ratios of (Ks/Sini) are analyzed. As the inhibition constant (KI) is not constant for all the enzyme reactions and it varies with Cr(VI)ini, the correlation between (KI) and Cr(VI)ini is developed. A set of differential equations pertaining to bioremediation of Cr(VI) has been solved using FORTRAN 90 program adopting the model developed. The results are verified with the experimental data from the literature and a good correlation has been obtained between the experimental data and the model predictions. Keywords: bioremediation, hexavalent chromium, mathematical model, inhibition kinetics

Sep 1, 2012

By Andrew T. McBride, Malcolm S. Powell, Indresan Govender

"Current empirical Semi Autogneous Grinding (SAG) mill models contain assumptions concerning the amount of energy available for particle breakage, how this energy is distributed in the mill media and the rate at which the energy is transferred. Despite these assumptions the JK SAG model is highly functional with a proven track record. DEM provides a numerical framework to greatly improve on these assumptions that were necessary due to a lack of available input data.This paper identifies key outputs of the Discrete Element Method (DEM), such as energy spectra and impact probability distribution. It describes how they can be incorporated into current mill models utilising practical rock breakage data. The rate at which energy is transferred is shown to be dependent on particle position and mill rotational speed and not once per cycle as previously assumed. Based upon this an improved energy transfer methodology is presented. The fundamental outputs of the DEM are validated against experimental three-dimensional particle tracking data, so as to establish whether the DEM produces correct energy transfer predictions on the inter-particle level, which is crucial to this work."

Jan 1, 2003

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture.In particular Davy derived an equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. Furthermore, this covariance can also be used to measure the variance of the composition distribution of each mineral.This paper shall present results verifying this equation. The experimental method was based on obtaining particle information from serially-sectioned particles. Particle samples selected for serial sectioning displayed a range of natural textures including liberated, binary and composite particles. The exposed surface of the polished sections were analysed using QEM*SEM. This procedure was repeated until all of the grains have been polished away. The covariance of mineral distributions were calculated from the serial sections and compared with that calculated using Davy’s equation."

Jan 1, 2003

By Peng Qian, Xiao Li, Guoyan Fu, Peiwei Han, Yongliang Wang, Shufeng Ye

"Arsenic removal from high arsenic gold concentrate is conducive to increase the mineral value and realize the mineral comprehensive utilization. This study investigated the alkaline pressure oxidation leaching (APOL) of an arsenical gold concentrate in lower temperature to separate the arsenic into filtrate. The effects of temperature, NaOH concentration, solid-liquid ratio, reaction pressure and stirring speed on the leaching efficiency were investigated, and the characteristics of the gold concentrate and leaching residues were evaluated using XRD and SEM analysis methods. The obtained results showed that by using lower temperature (<60?) it is possible to avoid the production of elemental sulfur during the leaching process, which is benefit for the oxidation of arsenopyrite; When the reaction was carried out under appropriate conditions, more than 98% of the arsenic will be extracted into the filtrate as the form of arsenate or thioarsenate. INTRODUCTION In recent years, there has been considerable interest in the recovery of gold from refractory arsenical gold ore. The arsenic in this kind of ore usually exists as the form of arsenopyrite, and the gold surrounded by arsenopyrite exists as the form of fine particles, which will give many difficulties to metallurgical work. When the content of arsenic in the gold ore is more than 0.5%, it will seriously penalize the smelting efficiency (Ruiz et al., 2014). So pretreatment of the refractory gold ore is necessary to obtain the largest economic value and environmental benefits (Balaz et al., 2000). The oxidation pretreatment processes mainly include roasting oxidation, pressure oxidation, chemical treatment and biological treatment (Ann et al., 1992; Kou and Chen, 2012; Tongamp et al., 2010; Fernandez et al., 1995; Lin and Zheng, 1996). Among them, the roasting oxidation and pressure oxidation are the more ordinary processes in industry. The roasting oxidation process is the mature and adaptable technology, but the production of waste gas containing sulfur and arsenic will pollute the environment. The pressure oxidation method possesses certain metallurgical and environmental advantages, and can efficiently decompose the mineral. According to the different solution media, the pretreatment can be divided into alkaline and acidic pressure leaching pretreatments (Papangelakis and Demopoulos, 1990; Hiskey and Sanchez, 1995). The acidic pressure oxidation method has been used in most smelting plants for high arsenic gold ore pretreatment, while the alkaline pressure oxidation is still not widely applied. Compared with the acidic pressure oxidation, the alkaline pressure oxidation can be realized under lower temperatures."

Jan 1, 2018

By Gustav Hawlitschek, Henrique Kahn, Carina Ulsen, Renato Contessotto

"The problems related to waste dumping increased with the growth and development of large cities. In the U.K., more than 50% of landfill waste comes from construction use and the U.S. alone produces around 200 to 300 million tons of CDW annually. The exhaustion of natural sand deposits close to large urban centres stimulates the recycling of construction and demolition waste for the production of recycled aggregates as a construction material. This paper presents a flowchart for the production of recycled sand with low porosity and regular shape by the selective removal of the cement paste attached to recycled aggregates. The products characterization was carried out by the determination of the particle size and shape distribution, chemical and mineralogical composition, heavy liquid mineral separation and quantification of all present phases using a scanning electron microscopy with automated image analysis (SEM-MLA). The comminution of CDW by vertical shaft impact crusher made possible the production of a lower porosity recycled sand. The heavy liquid mineral separation showed that the proportion of low porous phases (d>2.5 g/cm3) is very high, exceeding 70% of the weight, encouraging further mineral processing separation to obtain a fine recycled aggregate with less cement paste content. The mineralogical characterization by XRD and SEM indicates that the main phases are tectosilicates, phyllosilicates and calcite which one can be attributed to both calcareous aggregate and cement paste. The precise quantification of cement paste and calcite/dolomite alone is just possible by automated image analysis. The characterization results demonstrated that proportion of phases with no cement paste attached increases progressively in denser products. The results of heavy liquid separations and image analysis are comparable and automated image analysis can be used for the characterization of phase content and their main associations."

Jan 1, 2014

The flotation behavior of kaolinite and diaspore using N, N-diethyl dodecyl amine (DEN12) and N, N-dimethyl dodecyl amine (DRN12) as collector have been investigated through flotation experiments. The mechanism of adsorption of two tertiary amine collectors on surface of kaolinite and diaspore were investigated by FTIR spectral, Zeta potentials measurements and calculation of molecular orbital energy. It has been found that DEN12 and DRN12 have stronger collecting power to kaolinite and weaker collecting abilityto diaspore than DDA. Kaolinite and diaspore in bauxite ores can be separated by using DEN12 and DRN12 as collectors at pulp pH below 8 and 6, respectively. The results of zeta potentials and calculation of molecular orbital energy indicated that the adsorption strength on kaolinite surface is in the order DEN12>DRN12>DDA and the adsorption strength on diaspore surface is in the order DDA>DEN12>DRN12. FTIR spectral analysis and Zeta potentials approve that the action between kaolinite and tertiary amine collector is strong electrostatic adsorption and that of diaspore is weak electrostatic adsorption in the range of pH 5~6.

Jan 1, 2014

By Brian Hart, Liuyin Xia, Staman Dimov

The recovery of rare earth elements (REE) is fast becoming of significant interest globally. Modern research and development programs (outside China) towards the optimization of REE mineral recovery by flotation have been lacking. Due to the mineralogical nature of many hosting deposits, the separation and recovery flotation flowsheets can be very complex. As part of a research project, a selected suite of hydroxamic acid collectors (Naphthoyl, Cyclohexyl, Benzoyl, Octyl, Terta-butyl benzoyl, Salicylic) were tested in order to examine their potential for recovery and selectivity. Micro flotation tests were conducted on a feed sample, recovery and grade of the products were used to evaluate their relative flotation efficiency and selectivity and these results (flotation with the hydroxamate collectors) were compared to a phosphoric acid/sulphonate collector mix(shorten as "mixed"). In the testing, the flotation response with the hydroxamate collectors was significantly better than the "mixed" collectors on freshly ground (no slimes removed) samples. Furthermore the tests revealed that for most of the hydroxamate reagents tested, their dosage requirements to achieve recoveries at the same levels was less than that for the "mixed" reagents. Product assays show that recovery of both La and Ce is significantly better for using the salicylic hydroxamate and that Nb, Y and Zr recovery are favored by using octyl hydroxamate. These results indicate mineral flotation selectivity could be achieved by using selective hydroxamtes. Spectral fingerprinting by TOF-SIMS surface analysis has allowed for the identification of reagent species. TOF-SIMS surface analyses of grains analysis confirmed that REE bearing grains reporting to the concentrates are doing so in response to collector attachment whereas grains reporting to the tails are doing so in response to a lack of collector. The TOF-SIMS surface data bas been used to examine the factors promoting flotation stream partitioning.

Jan 1, 2014

By K. V. Fedotov, G. I. Sarapulova

The study is devoted to the earth's surface protection and is aimed at improving the ecological safety of the territories in the mining industry. Identification of the diagnostic signs and quantitative criteria for the disturbance of soil geochemical properties and water chemistry represent an important scientific task in anthropogenically disturbed landscapes in the context of comprehensive exploitation of mineral resources. The study is aimed at geological and ecological analysis of the migration peculiarities of the man-caused chemicals and elements in soils and soil-surface water environment. We received new results. These results assist in estimating the peculiar features of distribution of heavy metals total and mobile forms (Cu, Ni, Zn, Pb), depending on the physical and chemical parameters of the disturbed soils. We obtained the empirical relationships describing heavy metals localization and accumulation processes depending on buffer properties of soils (pH, N, Corg), salinization factor and contamination with oil products. Anthropogenic geochemical barriers spontaneously formed in the area of industrial facilities were revealed in the territories of industrial facilities. These barriers prevent the further distribution of elements and pollutants in the landscapes. This makes it possible to create their artificial analogues in order to limit further migration of pollutants and to immobilize valuable components. Analysis of diagnostic features of soils geoecological state and factors influencing the distribution of heavy metals in the soil-surface water geosystem allows the identification of the geochemical barrier type with the aim of elements immobilization in a limited area of the territory. We applied modern physical and chemical methods of analysis, a package of statistics programs in Excel and modeling techniques. The proposed approach is innovative and therefore can be attractive. The accumulation of useful components losses in mineral resources exploitation is a promising reserve for their recovery from the soil with specifically arranged properties. The methodology of this research is also promising for the prediction of the environmental emergencies of the anthropogenic nature. This is consistent with the requirements of state control of environmental safety in the course of comprehensive exploitation of mineral resources.

Jan 1, 2018

By D. M. R. Sekhar

Certain types of rock phosphates of sedimentary origin are applied to acidic soils as fertilizer directly. Recent research in India showed that high grade rock phosphate in fine size when used as a mix with organic manure works as efficiently as di-ammonium phosphate (DAP) in alkaline soils. The rock phosphate from Jhamarkotra, India (sedimentary origin), Egypt (sedimentary origin) and South Africa (volcanic origin) showed good agronomic efficiency when used as Phosphate Rich Organic Manure (PROM). Further PROM shows equal residual effect. The results of efficiency of PROM made using two grades (+ 24% P2O5 and 34% P2O5) of rock phosphate mineral from Jordan show that low grade rock phosphate slimes are as effective as high grade phosphate concentrate when used in PROM. Also PROM is very effective in the saline soil of Eshidiya desert where DAP is not at all effective.

Jan 1, 2014