Search Documents

By T. Maio

Twelve years ago, Kennecott Utah Copper modernized its Refinery in conjunction with the modernization of the Kennecott Smelter with the latest flash smelting and flash converting technologies. The Refinery modernization consisted of installation of new polymer concrete cells, installation of KIDD TPS (total production stripping) system, installation of automated materials handling system, and the construction of a new hydrometallurgical slimes treatment process and precious metals plant. This paper outlines the Refinery operations and process improvements. Also presented are the newly implemented technologies and operating results of one of the world' s largest and most modern electrolytic copper refineries.

Jan 1, 2007

By X. Xe, B. Myhre, N. Zhou, B. Sandberg, Z. Chen

Effects of microsilica and reactive alumina type on flowability, flow decay and working time of Al2O3-SiC-C castables for blast furnace trough were investigated. The results show that at a targeted self flow values of (80 ± 10)%, water demand markedly decreases with increased microsilica addition. The nature of reactive alumina has a strong influence on flowability of the castables. Higher microsilica content contributes to a longer working time. The flow decays gradually until the working time and then drops abruptly. In addition, microsilica have positive effect on both cold strength and hot strength.

Jan 1, 2004

By K. Fujita, T. Kikuchi, Y. Sakamoto

Ceramic fibers were classified as a category 2 carcinogen by The European U legislation. Therefore we developed non-fibrous insulating castable which utilizes n porous aggregate, which is composed of Calciumhexaluminate. Although at beginning we applied alumina cement as binder for non-fibrous insulating castable, kind of formulation had a poor resistance to spalling. We developed non-fibrous insulating castable without alumina cement. This solved a problem which pre\ formulation had a poor resistance of spalling. We applied a new non-fibrous insub castable for reheat furnace in steelworks, then we could achieve good result which condition equivalent to ceramic fiber insulating castable.

Jan 1, 2004

By R. F. Favreau

"After a blast, the volume of the blasted rock normally occupies more space that it did before the explosion. The degree of such swell significantly affects the efficiency of digging the muck with a shovel or dragline. This paper explains why swell occurs, and describes the new subroutine SWELL of the blast simulator BLASP A which can simulate blast-induced swell. Results are also presented which display the effect of various blasting parameters on the degree and distribution of the swell within the muck pile of a bench blast. IntroductionIt is a common opinion that fragmentation is the most important of the various aspects which affect the efficiency of excavating rock with explosives. This paper proposes that, in fact, displacement and swell of the blasted rock are as important as fragmentation if the excavation process is to be rapid and efficient. It must ""a priori"" be recognized that a minimum degree of fragmentation is indeed necessary. For a given shovel or dragline, this minimum degree of fragmentation may be defined as follows: even the largest fragment of rock must be easily contained within the bucket. Once this criterion is met, however, there are good reasons to believe that displacement and swell take over as the key criteria which influence the rate of mucking, in cubic metres/hour. If the muck pile is not well displaced and swelled, the teeth of the bucket have difficulty penetrating between the rock fragments even if fragmentation is good and, as a result, the mucking is slow and inefficient. The purpose of this paper is to use computer simulations on the model BLASP A to demonstrate the effect of the blast design parameters on the displacement and swell of the blasted rock."

Jan 1, 1993

The Rabbit Lake In-Pit Tailings Management Facility contains frozen layers of tailings due to subaerial deposition during the coldest periods of winter. Thawing is required to ensure full consolidation of the tailings and to regain disposal space presently occupied by ice. Electric resistance heating has been used to heat soil for bitumen extraction and remediation of volatile contaminants. A preliminary evaluation of the application of electric resistance heating to thaw about 0.3 cubic metres of frozen tailings was conducted using tailings frozen at about -2 oC. Visible thawing of the tailings mass was observed after 25 hours, demonstrating the feasibility of this approach.

Aug 1, 2010

By J. Aguilar-Santillan, H. Balmori-Ramirez, R. C. Bradt, I. Vernet-Patiño, F. Cunha

Kyanite is an alumino-silicate mineral that has been widely used for the production of refractory products for industrial applications. Kyanite provides a high alumina content, it readily produces mullite during firing, good hot strength of products and can be adapted to produce dimensional stability of products during firing. This research addresses the application of kyanite in mixes to produce (0 dense mullite aggregates with the addition of alumina, (ii) dense composite refractory aggregates of forsterite / spinel with additions of magnesia, and (iii) dense cordierite aggregates with the addition of talc. Effects of attrition milling and conventional ceramic processing are addressed as they affect the properties of these unique aggregates.

Jan 1, 2004

By T. Cutard, H. Marzagui, E. Ouedraogo, M. Roosefid, M. Prompt, C. Deteuf

The present work is achieved in the framework of a French national program on modeling and experimental characterization of the thermo-mechanical properties of refractory materials (PROMETHEREF). This research program is aimed to establish fair models and experimental database and to make it available to industrial partners for numerical simulation of industrial structures made of these materials. The present paper focuses on two silica-alumina refractory castables, an andalusite based one and a bauxite based one. We will present the first rheological characterization results achieved at room on normal and preheated samples of these two refractory castables. Refractory castables are characterized with the help of four points bending tests, compression tests and tensile tests.

Jan 1, 2004

By A. Sadough vanini A. Kami

In this paper, effects of different ageing treatments on the mechanical properties, microstructure and formability of 7075 aluminum alloy have been studied. Forming limit diagrams of the alloy have been obtained for four ageing conditions including T6, OA1, OA2 and O. For this purpose, combination of uniaxial tensile tests and the Erichsen cupping tests with different sizes and shapes of sheet specimens have been performed after each ageing treatment. The highest formability and the lowest formability have been observed at samples with O and T6 ageing treatments, respectively. Also, investigation of precipitated microstructures showed that the size of precipitation particles has a significant effect on the formability of the alloy. Formability improves with coarsening of precipitation particles.

Oct 1, 2011

By Sadough vanini Ali

The silicon anisotropic wet chemical etching technique is widely employed for fabricating various microelectromechanical system (MEMS) structures for advantages such as simple etching equipment and its capability to fabricate special microstructures. In this paper, we consider a complete theoretical derivation of the analytical solution based on geometrical and kinetic aspects of step flow on any surface and with a mathematical method we derive new equation for calculating the microscopic etch rates of surface atoms for a new range of concentrations and temperatures. Furthermore, a novel equation is presented for the calculation of the microscopic activation energies for some typical surface atoms and a new comparison of activation energies between some atoms is made that divides atoms into three categories. The results demonstrate agreement with the experimental results.

Oct 1, 2011

By J. Larose, E. Irissou

The aerospace business has always been driven by innovation. A significant portion of the overall business technology development strategies is still based today on improved materials and coatings. In this highly regulatory business environment, large amounts of funding are required to increase the maturity level of novel technologies, but the evolution process still remains a delicate endeavor. The technical risks involved during technology development obviously need to be managed and mitigated throughout the development cycle, but other hurdles almost inevitably get encountered, such as budget limitations, transition from lab scale to production scale, loss of focus, intellectual property negotiations and supply chain integrity. This presentation will cover some of the issues raised when a great idea is slowly morphed into an aerospace production part.

Jan 1, 2010

By T. Watanabe, M. Nakagawa, K. Kimapong

Lap joint of A5083 aluminum alloy and SS400 steel was produced by Friction Stir Welding (FSW) Process. The effect of welding parameters such as rotational speed, traverse speed and tool dimensions on the mechanical properties and the interface microstructures of the joints were investigated. FSW process could successfully produce the lap joint between A5083 aluminum alloy and SS400 steel. The variations of rotational speed, traverse speed and pin depth of a rotating tool gave rise to various characteristic interfaces of the lap joint and had conspicous influences on the joint properties. The increase in hard and brittle intermetallic phase and defects formed at the interface of the joint decreased the mechanical properties such as the shear load of the joint.

Jan 1, 2004

By A. Chaisantikulwat

Most solid-oxide fuel cell (SOFC) modeling emphasizes steady state cell operation. However, understanding the dynamic behavior is essential to predict the performance and limitations of SOFC power systems. In this work, we demonstrate a dynamic model of a SOFC, and we simulate a feedback control scheme that can maintain output voltage despite load changes. Dynamic response is determined as the solution of coupled partial differential equations derived from conservation laws for energy, mass and electric charge. From such a model, the step responses to system input variables can be determined. Low order dynamic models that are sufficient for feedback control design can be derived from the step responses. The development of the partial differential equation model is outlined, and the limitations of the control system are discussed.

Jan 1, 2005

By I. Colquhoun

Current practice tends towards "integrity as an afterthought". That is, integrity is treated as an isolated aspect of operations and maintenance. In fact, this works quite well. But it would work so much better and with less uncertainty if integrity management measures were introduced at the design phase and addressed the entire life-cycle of the pipeline asset. The talk will address the measures and metrics that can be implemented on a new pipeline during design to optimize integrity and deliver a comprehensive operating manual and integrity management program for the pipeline system. This deliverable should describe the risks to be assessed and monitored, and the actions to be taken to control these risk adequately. Properly executed, integrity by design will provide a good working estimate of the life-cycle integrity management costs and maximize system reliability.

Jan 1, 2005

By B. Farabi Khoshmehr

In the present study the effect of Silicate Sodium oxidation agent concentration and Plasma Electrolytic Oxidation (PEO) treatment time were investigated on properties of oxide layer on Aluminum alloy. The phase composition and surface morphology of PEO films were evaluated through x-ray diffraction (XRD) and scanning electron microscopy (SEM). Pin on Plate abrasive machine were used to investigate of were resistance of coating. The results showed that oxide layer which formed on Aluminum surface consist of high temperature a- Al?O? and ?- Al?O? phases. The diffraction peak intensity and percentage of these phases were increased by increasing silicate sodium concentration. Microscopic studies revealed a porous surface for PEO coating. This was affected by silicate sodium concentration and oxidation time. The wear test results showed that the weight loss of PEO coating was reduced due to improvement of their wear resistance.

Oct 1, 2011

By A. Morales

Flue dusts from a copper smelting furnace (continuous furnace), have been extensively characterized. The main phases detected have been cuprospinel, anhydrous copper sulfate (chalcocyanite), lead sulfate (anglesite) and arsenic oxides (claudetite and arsenolite). As minor phases, zinc sulfate (zincosite) and several copper or copper/iron sulfides were detected (digenite, anilite, bornite, cubanite), and also a copper oxide (tenorite). The suspension of this material in water leads to the partial dissolution of copper and zinc (chalcocyanite and zincosite) and arsenic oxides. The hydrocyclone classification of the residue makes it possible to obtain two fractions: a copper-rich coarse fraction and an arsenic-rich fine fraction. The coarse fraction can be recycled to the smelting furnace and the fine fraction can be mixed with wastewater sludge from a paper factory, to make both residues inert before disposing them to landfill.

Jan 1, 2007

By M. Reza Bateni, M. Zandrahimi, J. A. Szpunar

Titanium aluminides and nickel aluminides offer the potentials, as coating materials, for high temperature and aerospace applications. In this research, attempt has been made to develop Al-Ti and Ni-Al intermetallic compound coatings on the surface of Inconel 738. The coatings applied through pack cementation and simultaneous diffusion annealing processes. Scanning-electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDAX) and grazing angle X-ray diffraction were used for evaluating of coating structure. It was demonstrated that the pack cementation technique could be used to develop TiAl3 and AlNi intermetallic compounds coating on Inconel 738 substrate. When pack cementation technique is based on a halide-activated pack with aluminum and titanium powders, the coating consists of TiAl3 intermetallic compound phase. Whereas, by pack aluminization of Inconel 738, the coating consists of AlNi intermetallic compound phase.

Jan 1, 2004

By J. Schmidt

Cold drawing of copper wire rod is usually combined with an in-line annealing process to adjust the ductile microstructure of the wire again. One important key factor for successful annealing is the quality of the copper itself. Rod producers can check the recrystallization behaviour of the rod by different methods: chemical analysis, Spiral Elongation Test (SEN) as well as the Rapid Elongation Test (AR) are some examples of common testing methods. The comparison of the results of these methods does not always show sufficient correlations. The paper introduces firstly the SEN and AR-Tests and their different approaches to the mentioned task. The second step is to compare some results of the SEN-Test with the results of the AR-Test and identify causes of deviations. Thirdly, the effect of pre-annealing is discussed, which is especially common for wire rod with diameters of more than 8 mm.

Jan 1, 2007

By M. S. Moats

As smelter feeds become more complex, the impurities that ultimately report to electrorefineries are changing. Many of these impurities collect in the electrolyte and must be controlled. As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the interaction between electrolyte composition and anode passivation can cause operational difficulties. To improve the industry's understanding of the passivation phenomena, the role of electrolyte composition was evaluated using commercial electrorefining anode samples. The electrolyte composition variables examined were copper, acid, nickel, arsenic, chloride, thiourea and glue. Finally, the role of non-commercially utilized additives, such as bromide and polyethylene glycol were studied. From this investigation, electrolyte parameters that inhibit copper dissolution through copper sulfate precipitation, copper oxide stabilization and/or absorbed species lead to accelerated passivation. Species that prevent passivation have the ability to complex cuprous ions. Possible mechanisms for the role of each.

Jan 1, 2007

By Jerry Danni

In order to remain viable today, corporations must view the environment as a strategic issue, and integrate environmental management throughout the organization. Corporate programs that used to be based primarily on regulatory compliance now must emphasize strategic environmental management systems, and must integrate these environmental systems with basic business functions. The mining industry today is global, and must have an organizational structure that can embrace different cultures, physical settings, and regulatory regimes. Sound environmental management practices are not different from good management principles. An effective environmental management system should be a complementary system to an organization?s overall management framework, integrated and aligned with the existing management structure. Integrating environmental management into core business functions is just good business. An effective environmental management system is a critical component of a company?s commitment to environmental, social and economic accountability. This paper presents the elements of the Kinross Gold Corporation strategic environmental management system and discusses the integration of the environmental management system into the core business functions throughout the Company

May 1, 2003

By G. P. Cooper

A comprehensive computational heap leach model was used to evaluate options for operating a chalcocite-ore heap leach process. The stockpile leach model is based on the computational fluid dynamic software framework PHYSICA+ and incorporates various physical and chemical phenomena to simulate fluid transport, mineral reaction kinetics, bacterial effects, and heat, energy and acid balances for the overall leach process. The leach model is calibrated against small-scale column leach tests, and simulation results are validated against closely controlled column pilot-scale tests. For a given set of ore conditions, the effects of raffinate irrigation rate are examined. Several options for pulse leaching were investigated, and the effects on copper recovery and pregnant leach solution (PLS) grade are described. Model simulations indicated that pulse leaching could be used to control copper grade of the PLS. Finally, an analysis of inventory issues is presented for various lift heights including multi-lift simulations to examine potential operating options. U sing irrigation rate, raffinate copper grade, and lift height as variables in a factorial design of experiments, the simulations showed that raffinate copper grade is the main factor that affects the soluble copper inventory grade.

Jan 1, 2007