Search Documents

By Laurence D. Burke

The electrocatalytic behaviour of gold in aqueous media is surprisingly complex and a novel view of gold electrode surfaces is proposed to explain the observed electrochemical responses. The metal surface is considered as a chemically (or redox) modified electrode, with equilibrated, low energy, surface gold atoms functioning as a relatively inert support and low coverage, high energy, protruding gold atoms (or minute clusters of same) functioning as electrocatalytic redox mediators. The protruding atoms are viewed as surface active sites and the complex electrocatalytic behaviour is attributed to the basic instability of the mediators, the diversity (and poor control) of same, and the acid/base (or hydrolysis) behaviour of the oxidized states of the mediators. It is assumed that major advances in the application of gold in the heterogeneous catalysis of gas phase reactions will be accompanied by similar advances in the use of gold in the electrocatalysis area; however, this will require considerable work of both a practical and theoretical nature.

Oct 1, 2003

By E. Stansfield

Coal samples are sometimes taken from a wet spot in a mine, or from an open car or pile shortly after rain, and submitted for analysis in a dripping wet condition. Other samples are taken from a dry spot in the mine, or from an open car or pile after a period of dry weather. Comparison of the analyses obtained in the two cases would be absurd, although the samples might be of essentially the same coat apart from the surface moisture on the one. The analyst therefore attempts to reduce all samples to an equal basis by the operation known as air-drying. Air-drying is practised by the chemist for three reasons: (1) To make it possible to grind the coal to powder. (2) To bring the coal sample to a condition in which it will not change in weight rapidly whilst portions are being weighed out for analysis -in other words, to bring it into equilibrium with the air in the laboratory. (3) To determine the water-retaining power of the coal. Any kind of drying is satisfactory for (1); the coal should be dried more or less according to the humidity at the time in the laboratory for (2); whilst it should be always dried to the same extent for (3). In other words, no method can be satisfactory for both (2) and (3). In this paper the only question considered is (3) -that is, air-drying the coal under standard conditions so that strictly comparable results can be obtained for the water content of coals after air-drying. After a sample of wet coal is exposed, it loses moisture until it is in equilibrium with the air at the time: thus the coal will loose distinctly more water in air of 20 per cent relative humidity, for example, than it would in air of 80 per cent.

Jan 1, 1923

By Marcel Laflamme

Underground mine workers are continuously exposed to many sources of noise and vibration in carrying out their tasks. Even though the vibration and sound level of some mining equipment is documented, it was found that this information is not readily available for many pieces of equipment and that it is not considered when choosing equipment or planning tasks. As well, health problems related to vibration and noise are among the main causes of work-related compensations in mines. Considering those facts and although no Canadian regulations could force employers to limit the exposure of their workers to vibration, the Société de recherche et développement minier (SOREDEM) decided to address the problem by including vibration among their research priorities. In order to characterize noise and vibration sources of different mining equipment used for underground mining, the authors have performed a study in 8 different mines in Québec on 28 different mining equipments. The paper will present the procedure that was followed to select the list of equipment to be evaluated and the low cost acquisition system developed to perform multichannel time domain acquisition in harsh environments. It will also present the results obtained for the noise level produced by the equipment as well as for the hand-arm and whole-body vibration exposures.

Aug 1, 2013

By G. S. Crawford

Forecasts prepared by the B.C. Research Council for the National Harbours Board suggest that mineral shipments through B.C. Lower Mainland port facilities will increase more than four-fold, from 6 to about 25 million tons, during the decade 1965 to 1975. The longer term outlook is for a six-fold increase to about 35 million tons by 1985. In 1967, minerais accounted for more than one-third of the total deep-sea traffic tonnage, nearly as much as grain. By 1975, the minerals' share will be about half the total. The principal items are exports of potash from Saskatchewan, and of coal and sulphur from Alberta and British Columbia. Additional exports include copper and other mineral concentrates and propane. Imports are chiefly salt and phosphate rock. Coastal traffic in such items as cement, sand and grave!, and limestone totalled 3.3 mil-lion tons in 1967. They will continue to be of major importance, but do not have the spectacular growth potential of the deep-sea traffic.

Jan 1, 1968

By W. Dan Hausel

"Abstract-Hundreds of diamonds have been found in the United States. The majority of the discoveries occurred during the 19th century as a by-product of placer gold mining. Most of these early diamond finds have no known source, and in many cases are situated in areas unfavorable for diamond exploration based on current models that require kimberlite or lamproite to be emplaced in a stable Archean craton or Proterozoic craton margin.Diamonds have also been recovered in situ from lamproite at Murfreesburo, Arkansas, from kimberlite in the Lake Ellen region of Michigan, and in several kimberlites in the Colorado-Wyoming State Line district. Unverified reports also suggest that diamonds may have been recovered from other related intrusions at a number of localities in the United States."

Jan 1, 1995

By P. R. Geoffroy

Extensive and Intensive Prospecting As often pointed out, the search for new ore deposits may be carried on along two widely divergent lines. It may be either extensive or intensive. By extensive prospecting we mean a search for mineralized outcrops conducted over large and more or less virgin tracts of land, followed by a test of the practical value of any discovery made, the test being limited to the immediate vicinity of the outcrop. Extensive prospecting, was, in fact, the only policy known to the early prospectors. of the American continent and is still the rule in the remote sections of the Canadian Shield and in the African wilderness. It can be further characterized by the lack of emphasis placed on geological and other technical means as an aid to the search for ore. However, very little virgin ground is left, nowadays, for a man or a company to test their luck, and whatever is left is so remote from the necessary means of development that any new discovery will require considerable delay and expenditures to be amenable to profitable mining. On the other band, a great many of the favourable and still unexplored areas (and this is particularly true in Canada) are overburdened to such an extent that outcrops of bed-rock are extremely scarce and extensive prospecting is nearly impossible. Intensive prospecting, to the contrary, must be understood as a detailed search for ore carried on over limited areas in districts already known to be mineralized and covering regional structures whose relation to mineral deposits bas been estahlis.hed with a fair degree ot certainty. The search for deep-seated deposits in the vicinity of successful mines is a perfect example of intensive prospecting. As a matter of fact, the majority of the geologists employed by the mining industry are engaged in some kind of intensive prospecting.

Jan 1, 1950

By R. Heikkilä

In this paper the utilisation of building information models (BIM) and construction automation on building sites is discussed. A lot of research has been carried out to develop new applications for using BIM to assist construction site planning, different operations and logistics. The methods of production control and management on site utilize BIM together with machine control and navigation systems. In Finland machine control systems and the automation of construction equipment is widely used in infrastructure construction. Recently similar methods have been introduced also in building construction. This paper describes some latest Finnish examples where BIM-software is used for the planning, execution and control of building construction operations. University of Oulu has studied methods and technologies to capitalize BIM-models. The research has been mainly in infrastructure construction but the activities have recently been extended to building construction. In this paper a BIM-based tower crane operation and control system is discussed as a case study. The aim of this study was to highlight the potential areas were automation can increase the crane productivity and improve site operations and logistics. The construction site managers and tower crane operators interviewed in this study were experienced in using BIM-models on site.

Aug 1, 2013

By DALE MacGREGOR, VERA TUREK

lndusmin Limited acquired the St. Donat quartzite deposit in 1967 to produce high-quality silica for use in the sandblasting and silicon carbide industries. The quartzite, of Grenville age, is highly friable and porous. This is due to numerous small, kaolinite-coated cavities in the quartzite; the cavities were formed through leaching, probably by rising hot solutions.

Jan 1, 1984

By S. Devereaux, P. Gover, S. Everett

Having real-time data of blast furnace burden profile with respect to burden height and temperature is critical to making informed decisions on blast furnace operation. Given the high temperature and gaseous environment within the blast furnace shaft, traditional instrumentation has been limited at providing the level of real-time feedback information needed to optimize blast furnace operations. Infrared thermal imagery technology provides non-contact temperature measurement across the entire burden profile, allowing for better understanding of the dynamic movement of the burden within the blast furnace shaft. This technology increases blast furnace performance by improving the decision-making process for hour by hour operations. This paper will discuss the development of incorporating infrared thermal imagery technology into the operating strategy of a lead blast furnace.

Jan 1, 2015

By Bob Drew, Goran Vukovic, Bojan Zivanovic, Klaus Gamweger

Reaction bath temperature is a major factor in processing liquid metals and in many applications where a balance between process duration and temperature has to be found to run a procedure efficiently. Also extremes of temperature can decrease the output of a process if too cold or even make it impossible, conversely overheating can be detrimental to both the product and furnace integrity. With the help of the new online temperature measurement system very accurate monitoring of the process is possible in contrast to the current routine practice where the temperature is measured periodically with dip thermocouples. The system works with a digital, fiber optic pyrometer, which is embedded in a refractory housing. Installation in the lining is possible below liquid level as nitrogen is blown to keep the system open and to ensure continuous sight from the optical head of the pyrometer to the molten metal through the tuyere. This permanent temperature measurement gives optimal process control with the potential of taking appropriate actions at an early stage enabling proactive process control. Therefore energy savings and even process endpoint detections can be realized.

Jan 1, 2015

By D. Runnels, A. Allaire, J. Torrealba-Vargas

Data mining and modelling of operational data involves the discovery of patterns in large datasets for future use in benchmarking and plant optimization. The modern pattern of discovery in large data sets involves statistical techniques, machine learning and new visualization tools. Former examples of data mining are revisited and presented in this document. INTRODUCTION A network of enthusiastic and active professionals is currently developing and maintaining several open source statistical software tools (packages) for data analysis (example Rstudio, Orange, Spyder, etc.). The advantages of the open source software philosophy are the fast development and testing of the solutions presented to the community. Books and support are available for each software application. Since each modern work activity generates massive amounts of data, it is attractive to learn and test those available tools considering that we are at the door of the new work revolution coined as “Mine 4.0”. Data mining involves collecting large datasets, the preparation and cleaning of a dataset (term named data wrangling), the uploading of the data to a database program capable of handling big datasets, the development of prediction models and the presentation of the results. Machine learning techniques help to develop mathematical models and algorithms that could be used to improve the performance on a specific task. Mine operations are producing an incredible amount of data each day and the need to analyze those results seems to be impossible due to the lack of time, as well as the lack of skills to investigate the data collected. If we add to this the traditional habit of working in silos, an additional challenge is to consolidate databases from different departments in search of trends that could help to optimize production.

Jan 1, 2019

By M. A. Nadar

Harsh and dynamic construction sites are generally equipped with cranes in order to rapidly and conveniently move heavy loads from one location to the other. If not properly inspected and managed, this operation can be very hazardous and lead to accidents. As such, a reliable and self-contained monitoring system that can update construction and safety personnel about the status of the crane, the weight of the load lifted, the location of the boom with respect to nearby buildings and other tower cranes, and the weather conditions under which the crane is operating, is deemed necessary. This can lead to significant time and cost savings as well as safety and productivity improvement due to the accuracy and immediacy of relevant on-site crane information delivery. This paper takes the initial steps and presents research targeted at evaluating the capability of wireless sensor networks (WSN) for monitoring tower crane operations in construction environments. A reliable long range WSN system is implemented and information is obtained from various special-purpose sensors (temperature, wind, proximity, etc.) mounted on special motes that relay data to and from each other and a central hub. The latter continuously monitors and manages network performance and relays incoming data to the host application. This application, in turn, displays the received data, and maps it onto a user-friendly visualization scheme, triggering alarms when a set of pre-programmed rules and safety conditions are crossed. The components of the proposed system have been tested through proof of concept experiments and preliminary results highlighted the potential of WSN systems for improving monitoring of tower cranes and reducing related accidents on construction sites, especially in Lebanon and the Middle East region where safety precautions are usually not properly implemented.

Aug 1, 2013

By R. D. H. Wigmore

"The title of this paper probably sounds quite simple and self-explanatory. The problem, however, was not a simple one, and proved somewhat baffling and expensive over a period of years. After outlining the problem, and the methods which were used to overcome it, we will present our solution, or perhaps it would be more accurate to say the partial solution which we reached.We have in the cyanide circuit at Upper Canada two Dorr Single Tray Thickeners with 30 ft. diameter wood stave tanks 12 ft 4 1/ 2 in. deep. In the years prior to 1948, when the tonnage was 250 to 280 tons per day, two stage thickening was practised. As the tonnage was increased to 450, 500, and finally 560-600 the thickeners were used in parallel.Some settling problems were encountered, and in those days the means to combat these problems were very few. The only remedy was to dump in pounds and pounds of lime. Then along came a few reagents, and the writer remembers one in particular, - 11 Carboxel11 (carboxymethlycellulose). When water or solution was added to this reagent, the result was a gooey mass somewhat resembling tapioca. One drawback was that it stayed in this state, and didn't go anywhere. A method was finally developed of containing the mass (or mess) on a fine screen, and dissolving some of it was a fine spray of solution. The only thing the writer recalls was that it was not a very effective settling agent.Shortly after this time, along came the new flocculents, first a few, and then many, and our settling problems were over.But when the settling problem was solved at Upper Canada, some other problems were creeping up on us."

Jan 1, 1965

By G. W. H. Norman

The surficial Archæan rocks of the southern gold belt of western Quebec are constricted near Kewagama lake by granite masses to the north and south. This divides the belt into natural eastern and western parts. This paper deals with the eastern part, extending from Malanie to Haig township. In this section the Keewatin-Timiskaming rocks have a length of about 70 miles and end abruptly against garnetiferous gneisses of the Grenville terrain. In the western half of the section where exploration has been under way since the early twenties, there are sixteen mines that are or have been in operation, and eleven prospective mines. In the eastern half where exploration has been carried on since the early thirties, six prospective gold mines are under development, one· of which, Louvicourt Goldfields, is at the initial production stage. Of the sixteen properties in the western half that are operating or have operated, all, except the Golden Manitou, which is a base metal mine, and the old Green Stabell from which there was a small production of copper, produce gold. Of the eleven prospective mines in the western half nine have gold. New Bidlamaque has gold and copper and one, East Sullivan, has copper-zinc ore. Since production began in 1927 gold, silver, zinc, copper, and lead having a total value of about $10,000,000 have been produced from the mines of the eastern section of the southern gold belt of western Quebec.

Jan 1, 1954

By John Steele

The goal of this project is to detect the presence of objects behind haul trucks and to provide an alarm to the driver if such objects are detected. Objects of interest include people, pickups, other equipment, and large rocks. Another goal is to see if the system can identify the existence of a berm and determine the distance from the truck to that berm, so a safe backup distance can be computed and used as a reference. This paper presents results that demonstrate that such a system is feasible and includes results from work at a local quarry. Architecture of the system is provided and the various subsystems are discussed. Details of the algorthims are included and discussion of the issues involved in developing a fieldable system are also included.

May 1, 2003

By Michael Arriagada, Ivan Arriagada

"As mines return to shafts to economically exploit deeper reserves, two methods mine owners use to minimize short term costs are: sinking shafts in phases and refurbishing old, existing shafts. While there may appear to be benefits to utilizing existing infrastructure, often this is not the case, resulting in missed deadlines and added costs. Similarly, if proper long term planning is not executed when sinking a shaft in phases, additional costs and downtime will be accrued. This paper will take an in depth look at both of these options with an eye towards optimizing costs, minimizing downtime, and facilitating construction. INTRODUCTION With the onset of mechanized mining and large capacity trucks, many mines turned away from shafts and began to use ramps to haul ore to surface. However, continual exploitation of mineral reserves located closer to surface, combined with the subsequent unearthing of additional resources at greater depths, forced mines to go deeper and deeper to extend the life and keep the operation running. In shallow mines, hauling ore by truck was an economical option. However, as mines get deeper, driving ramps takes additional time, and hauling over longer and longer distances becomes less economic, both in terms of cost and time. For this reason Mexico, in particular, has seen a jump in the number of shafts which have been put into production, as well as having a number of shafts in different stages of development and still more in the conceptual stages. Many of the shaft projects in Mexico are being designed in phases, with the hoist and equipment purchased capable of reaching the ultimate planned depth of the shaft, but with sinking operations stopping short at an intermediate depth. A loading pocket is then installed to start exploiting mineral at this depth sooner, with subsequent phases planned for a later date using either a rock pentice or bulkhead to separate the sinking operations from the active shaft above. Currently, we are directly involved in two such projects which are actively being deepened, as well as having seen various others already reach completion. If done properly with the long-term plan in mind, sinking in phases can be a very viable option, allowing for faster production while fully utilizing the equipment at various depths. However, there are many issues which can arise when sinking a shaft in phases that if not properly examined and planned for from the outset, have the potential to eliminate the gains hoped for when it was decided to sink in this manner."

Jan 1, 2019

By E. S. Moore

"The Centre of the silver-producing section of the Gowganda area lies about 55 miles northwest of Cobalt, and the village of Gowganda is 71 miles by road from New Liskeard. The geological similarities of the Gowganda and Cobalt areas led prospectors westward from the rich Cobalt field, first to Elk Lake and then on to Gowganda, where mineralization was found in 1907. A year later many showings were found, and rich hand-picked ore was shipped. Most of the ore has come, however, from two mines, both of which are still operating; the Miller Lake-O'Brien, which was purchased by Siscoe Metals of Ontario Ltd. in 1945, and the Castle-Trethewey. The annual production of these two mines runs over one and one-half million ounces of silver and considerable cobalt. The total production of the camp has reached about 32,000,000 ounces of silver and a large amount of cobalt, the total not recorded.General GeologyThe general geology of Gowganda is in many respects much like that of Cobalt. There are areas of Keewatin basic and acid Javas mixed with tuffs and basic intrusions. These rocks are deformed and partly altered to schists, and have been intruded by some Haileyburian basic and ultra-basic rocks and by Algoman granite. These were followed by a large number of porphyritic Matachewan quartz diabase dykes. After a period of extensive erosion the Huronian sediments were deposited on a pene-planed surface over all the older rocks; these sediments include large quantities of conglomerate (partly tillite), quartzite, and greywacke. The Keweenawan rocks include the Nipissing quartz diabase sill, later quartz diabase dykes, and one long olivine diabase dyke, the latest Precambrian rock. The area has been extensively glaciated.Structural FeaturesThere has been little folding in the area since the Algoman batholiths were intruded, and the Huronian sediments lie nearly flat, with dips of 10, 15, or rarely 25 degrees. The Matachewan dykes show a remarkably uniform, nearly north strike, indicative of east-west tension when they were intruded. On the other hand, the dykes later than the sill strike nearly east, tangentially to the northeasterly and northwesterly strikes of the Miller Lake basin."

Jan 1, 1949

By J. L. Casado-Sánchez

Financial capital is highly volatile and if the investor does not get adequate compensation for the risk faced he may consider withdrawing his capital assets from the company and consequently produce a structural change in any sector of the economy. We study the variation in profitability of assets in terms of the changes that occur in the markets. The choice of models used is justified by the extensive theoretical and empirical use of them throughout the history of financial economics. We have used the capital asset pricing model (CAPM) and the model based on the arbitrage pricing theory (APT) to determine the beta value. These models have been applied to the monthly returns of 27 mining companies listed on the New York Stock Exchange (NYSE) or London Stock Exchange (LSE), using data from the period covered from January 2006 to December 2010. The results of time series and cross sectional regressions for CAPM and APT produce some errors, suggesting that many companies have failed to obtain an adequate cost of capital. Also the results show that higher risk firms tend to have lower profitability. These findings make it unlikely to be maintained over the long term the current status and could drive structural change in the mining sector in the form of mergers.

Aug 1, 2013

By H. Hejny

Given the current status of political discussion in Europe about raw materials issues, the sustainable development of the extractive industry and the reduction of its environmental and societal footprint are among the key topics in this discussion. In this context, the European Commission approved the EO-MINERS project (Earth Observation for Monitoring and Observing Environmental and Societal Impacts of Mineral Resources Exploration and Exploitation). The overall aim of EO-MINERS is to bring into play EO-based methods and tools to facilitate and improve interaction between the mineral extractive industry, authorities, and the society in view of its sustainable development while improving its societal acceptability. Developing generic, standardised and reliable EO-based products to monitor the environmental and societal footprint of mining projects is the way chosen by EO-MINERS to improve this interaction, along with the organisation of tripartite meetings gathering all relevant stakeholders. The project uses existing EO knowledge and carries out new developments on three demonstration sites (Sokolov lignite mining area, Czech Republic, Witbank coal field, South Africa, Makmal gold mine, Kyrgyzstan) to further evaluate and demonstrate the capabilities of integrated EObased methods and tools in monitoring the environmental and societal footprints of the extractive industry during all phases of a mining project, from the exploration to the exploitation and closure stages. It contributes providing reliable and objective information about affected ecosystems, populations and societies, to serve as a basis for a sound ?trialogue? between corporate stakeholders, governmental organisations and societal stakeholders. The project already developed a set of consolidated indicators based upon previous knowledge about mining-related issues along with interviews of national, regional, and local stakeholders. These indicators reflect known environmental and societal issues at mining sites as well as the interest of various relevant stakeholder groups. The process described in the EO-MINERS project ? policy assessment > indicator identification > choice of suitable EO tools able to serve monitoring task > monitoring by EO tools > making available objective information for fair dialogue among stakeholders ? is generally applicable to all stages of a mining project. The key to success will be the right choice of indicators addressing the problem and subsequently the right choice of suitable EO tools and finally the willingness of all stakeholders to find a common solution. To this end, the EO-MINERS project organises site-specific ?trialogue? workshops at each demonstrations site, which aim to provide relevant information in adequate quality to the stakeholders as common ground for discussions. Local stakeholders, including mining companies, regulatory bodies, and community representatives are invited to participate in these workshops where the relevance of the developed EO-based products to environmental and societal impact assessment will be discussed. The presentation will discuss results obtained during these trialogue workshops, as well as the success and difficulties and reluctances encountered. The project will further indicate ways and means how the EO products and other project results may be used for monitoring purposes in all phases of a mine.

Aug 1, 2013

By W. M. Tupper

Municipal governments recognize the importance of aggregates in the local economy and the need to manage this resource in the interest of the public good. They have encountered problems with regulating the industry and the dichotomy between the urban need and the rural source. They have suffered from a lack of financial benefit, an adequate aggregate inventory, provincial strategy, economic information and public understanding. A provincial strategy for ensuring the availability of aggregate supplies to developing areas of the Province is essential. The Province should also be responsible for licensing, research, technical expertise on rehabilitation, public education and financial assistance. Upper-tier municipalities (regions or counties) should assume responsibility for resource management, including resource availability, demand characteristics, truck routing, phasing of resource development and sequential land-use planning. Area municipalities (towns and townships) can best determine the social and environmental impact of a specific aggregate development proposal and should therefore have the primary responsibility for the location of new pits and quarries. They should also have the authority to supplement provincial regulations concerning operating standards and the phasing and standards of site rehabilitation.

Jan 1, 1978