Search Documents

By Ham. Y. M.

The corrosion behaviour of Al-B4C metal matrix composites immersed in 2500 ppm boron-containing H3B03, 0.5 M K2SO4, and 3.5% NaC1 solutions was investigated. Effects of B4C particle volume fraction on the corrosion behaviour of composites were studied using potentiodynamic polarization and electrochemical impedance spectroscopy techniques. Scanning electron microscopy was employed to study the surface morphology of the material before and after corrosion. Results show that all materials investigated are more corrosion resistant in 2500 ppm boron-containing H3B03 than in other solutions. No appreciable corrosion was observed in boric acid and sulfate solutions in contrast to an obvious pitting in NaC1 solution for both base alloy and composites. The preferential pitting sites are the interfaces of Al/Fe intermetallics for the base alloy, and the A1/B4C interfaces for the composites. Increasing the volume fraction of B4C particles in the composite decreases its corrosion resistance of Al-B4C composites.

Jan 1, 2011

By A. H. Marquis

Since the start-up of its first Direct Reduction Module in April 1973, S1DBEC has produced over 2 million tons of prereduced iron. During this period, SIDBEC has acquired comprehensive experience in the operation of the direct reduction process and at the same time has learned to recognize the characteristics that the oxide should have to constitute an adequate feed for the process. A comparison is made as to the design and operation of the two direct reduction units now operating at Contrecoeur, Que. A description is given of a method of evaluation of a direct reduction unit, which takes into account the main process variable sand which permits comparison ofthe results on a daily basis. The paper defines the characteristics that the iron oxide and the prereduced iron pellets must have to meet the specific requirements of the direct reduction and the electric arc furnace processes. A simple model makes possible a rapid evaluation of the technical and economic effect related to the use of a given raw material. Finally, the paper outlines the advantages of prereduced iron in the steelmaking process and on the quality of the steel products.

Jan 1, 1979

By Daniel Hodouin, Claude Bazin, René del Villar

"A traditional linkage has long been established at Laval University's Department of Mining & Metallurgy between the Mineral Process (MP) and the Mining Exploitation (Min) on one hand, and between the Extractive Metallurgy (EM) and the Materials Engineering (Mat) on the other. This academic separation of Mineral Processing from Extractive Metallurgy at the educational level has become increasingly at odds with today's industrial practice in which both disciplines are not only complementary but also often intertwined. For instance, in gold ore processing, comminution, flotation, and gravity separation units are interfaced with atmospheric or pressure leaching modules and with carbon adsorption and electrowinning units. The new copper plants in South America combine comminution and flotation circuits with heap leaching, solvent extraction and electrowinning processes.In order to reflect this new industrial reality and to harmonise the options offered in both its engineering programs, the Department of Mining and Metallurgy of Laval University has introduced major changes in its curriculum in 1996. These changes reflect also the recognition that the somewhat secondary status given so far to Mineral Processing and to Extractive Metallurgy within their ""mother"" programs, Mining/Mineral Engineering and Materials metallurgical Engineering respectively, was in sharp contrast with their actual significance for the Canadian economy. Leading industrial voices have raised similar concerns and the Canadian Engineering Accreditation Board has also addressed this problem in its latest program evaluation.The changes implemented at Laval aimed at a) better representing MP and EM within the two undergraduate programs; b) training top-level versatile and multidisciplinary engineers, fluent in all aspects of MP and EM, irrespectively of which of the two ((mother)) programs they had chosen and capable of meeting today's industrial requirements; c) training students in process analysis, optimisation and automatic control using state-of-the-art software, and d) taking into account the co-operative nature of both undergraduate programs.Results are very encouraging in terms of student enrolment and industrial response. However, some concern is expressed on the sustainability of the renewed curriculum considering the drastic budget restrictions in effect at Laval as in most other Canadian universities."

Jan 1, 1999

By Brad Wells, Wayne Bull, Wayne Dickinson

"Antiscalants were evaluated for control of calcium carbonate (CaCO3) in gold processing applications. Under severely supersaturated conditions, 100 percent inhibition was achieved with 30 ppm antiscalant. Laboratory and field testing established that an antiscalant could both inhibit scale buildup and remove an estimated 0.5 kg/m2 per annum of pre-existing scale. A program was developed to control CaCO3 at a gold mill experiencing severe scale buildup. Annual accumulation of as much as 3 cm of scale in process piping was reduced to unmeasureable levels when 10 ppm antiscalant was applied. No scale-related upsets in mill operation occurred during a five-month trial period.INTRODUCTION Inorganic mineral scale is a crystalline deposit that forms when dissolved mineral constituents exceed the solubility of the respective mineral phase. Formation of mineral scale adversely affects a wide range of industries and is of particular interest in mining and metals processing. Scale affects numerous stages of metal extraction processes. Restricted flow in piping, nozzles, valves, screens, pumps and other components used to transport mineral slurries, metal concentrates, and tailings as well as scale in millwater and thickener overflow circuits are primary concerns (Alfano & Boffardi, 1994). Heap leaching, comminuation, flotation, vat leaching, carbon adsorption, and heat exchangers as well as oxidation steps used in processing sulfidic ores are among key unit operations that may be adversely affected (Simmons & Gathje, 2003). Antiscalant chemicals are designed to prevent formation and growth of mineral scales such as CaCO3. These chemicals, which include two primary classes – phosphonates and anionic carboxylate polymers and copolymers - are added to the gold processing stream at low parts-per-million (ppm) concentrations to interfere with nucleation and growth of scale forming crystals and to disperse fine particulate material. Application points may be located throughout the gold extraction process. Evaluation of the performance of antiscalants plays a critical role in determining the best product for a specific application. Performance evaluations include laboratory testing, pilot scale studies, in-plant trials, and ongoing performance monitoring during mill operation."

Jan 1, 2014

By A. Azizi, P. Blatter, A. Bouajila

"Due to the high reactivity of sulfide minerals in alkaline cyanide solutions, some parasitic reactions inflict a heavy gold surface passivation and excess cyanide consumption resulting in a dramatic decrease of the gold leaching rate. Atmospheric pre-oxidation was shown to be an effective tool to enhance gold extraction by preventing a passive film from forming on the surface of gold grains. This work aims to highlight efforts undertaken to determine: (1) how gold cyanidation is limited by passivation; (2) what are the reactions and mechanisms involved during gold cyanidation; and (3) how a better understanding of fundamental issues can be used to design a proper pre-oxidation strategy. INTRODUCTION Precious metals (PM), gold in particular, naturally occur in contact within a wide range of sulfide mineral systems. Hence, one of today’s most challenging R&D tasks consists in accounting for the presence of sulfides on the cyanidation behavior of gold. An important body of knowledge reveals that metal sulfides display a range of reactivities in alkaline cyanide solutions (Marsden & House, 2006). Such reactivities are acknowledged to inflict additional utility costs and loss of profits because they are accompanied with higher consumption of cyanide and/or formation of undesirable by-products that are often detrimental to gold leaching rates. Gold recovery in cyanidation is hampered by a multitude of factors, among others: (1) consumption of excess cyanide as a result of the formation of thiocyanate and dissolution of transition (Cu, Fe, Zn, etc.) metals (Habashi, 1967); (2) gold surface passivation by solid reaction products, e.g., Fe(OH)3 (Guo, Deschenes, Pratt, Fulton & Lastra, 2005), sulfur (Dai & Jeffrey, 2006; Jeffrey & Breuer, 2000;) or oxo and thiooxo (SbO33- SbS33-) salts in alkaline solutions (Guo et al., 2005). Because of their energy structure, most of the sulfide minerals exhibit semiconductor properties (Marsden & House, 2006). Therefore, the contact between constitutive sulfide minerals inside complex sulfurous ores entrains electrochemical phenomena in which sulfide dissolution is a genuine corrosion process (Azizi, Petre, Olsen & Larachi, 2010). For instance, galvanic interactions could be initiated between the various constituents within the ore and could substantially increase or decrease the reactivity of some of the associated minerals."

Jan 1, 2012

By R. G. Hamm

A brief outline covering the shovels and draglines in use in the open-pit mines of Western Canada, including British Columbia, Alberta and the Yukon, is given, followed by the procedure for the selection of the correct wire rope for each application. Such fa ctors as wire rope constructions, lay directions and types of cores are mentioned. Once the correct wire rope has been selected, there are variousfactors that can affect the service fife ofthe rope and the reduction ofdown-time during rope change-overs. Factors such as hairpin winding, types of Becket loops, and shovel drum and bail adaptors are described.

Jan 1, 1979

By Dale Lens, W. S. (Wayne) Cusitar

"The use of continuous loading and conveying technology for mining is currently practiced in relatively few mining environments and, even in these cases, on a non-exclusive basis. For the most part, and particularly in hard rock mining, appropriate equipment technology has only recently been developed for continuous loaders, mobile low profile crushers and flexible face conveyors. Mining R&D work by Inco Limited has promoted the development and proving of a loader suited to hard rock conditions and capable of sustained loading rates of500 tonnes per hour. Current R&D work at Inco will test the production capabilities of a low profile mobile crusher by CMS/Eagle and a flexible/ mobile face conveyor system by DME. This follows successful production testing of the Belt Bender concepts in potash mining in Saskatchewan and the development of enhanced extensible conveyor equipment features by DME. Numerous applications are seen for variations of the LCC technology in soft rock, hard rock and surface mining environments. Introduction In some respects, this paper is an announcement of new technology which has the potential to bring revolutionary change to the mining industry. It is also the story of technology transfer, in which mining concepts that have developed independently in underground soft rock and hard rock mines and in surface mining operations are being brought together for a common benefit. It is also the story of key developments in equipment technology which 'complete the cycle' of cooperating technical capabilities to enable the revolution to begin. The phrase ""technological revolution"" requires some defmition: an equipment innovation, or invention, or improvement, will only be revolutionary if its use gives rise to a significant new mining practice."

Jan 1, 1987

By Paolo Toscano, Dave Hall

"This paper discusses the project history, process design and layout of the Rainy River Gold Project mill. The circuit consists of a 55 x 83 primary crusher, 15 MW SAG mill and 15 MW ball mill. Both mills are twin pinion with LSS and VFD drives. A pebble crusher is located in the process plant with bypass and stockpile options. Gravity concentration followed by 30 hours of leach residence, carousel CIP, carbon recovery, cyanide destruction and tails disposal in a 1,428 hectare tailings management area (TMA).The Rainy River Gold Project is located approximately 65 km northwest of Fort Frances in north western Ontario. The project is scheduled to be commissioned and reach commercial production in mid-2017. Expected cost is $US877M and is comprised of an open pit mine, process plant, tailings management area and supporting infrastructure. The process plant is designed to produce gold/silver Dore’ bars.The project has been developed on the following timeline:• 1967 – First exploration• 1994 – 17 zone discovered• 2004 – 433 Zone discovered• 2005 – Rainy River Resources Ltd. purchases property • 2006 - ODM zone discovered• 2007 - Cap Zone discovered• 2008 - First NI-43-101 Resource completed• 2012 - PEA completed & Intrepid Zone discovered• 2013 - New Gold acquires Rainy River Resources• 2014 - Updated feasibility study completed & Environmental Assessment report submitted• 2015 - Detailed Engineering >95% complete, EA approved and construction commencesThe property is accessed by provincial highway 600 and is within 17 km of 230 kV power line and railway sidings. Key project criteria are summarized as follows:"

Jan 1, 2016

By Y. Bai, J. J. Liu, D. Q. Li, S. Z. Liu, X. T. Wang

"This paper presents the results of an industrial test using 8 t/d of Baotou concentrate (50% REO) of a clean metallurgical process, which includes: 1. Roasting with H2SO4 at low temperature (220~260 0C) in a batch roasting furnace followed by water leaching to obtain a leach liquor as feed with a yield of >95% RE and Th, recovering F as fluoride, producing a leach residue amounting to 1/3 of an equivalent high temperature residue and containing <0.03% Th and radioactivity < 3×104 Bq/kg compared to the normal high temperature residue containing 0.2-0.3% Th and 1×105 Bq/kg. 2. Separating Th with N1923 and extracting RE by P507 has been completed in mixer-settlers. Test results indicate that the ThO2 product has a purity of > 95% with a yield of 99%, and the RE has a yield of >95%, in which ThO2/REO <5×10-6, and that P507 loaded RE connect straight with separating RE using P507-HCl system. 3. Treatment and multipurpose use of "three wastes" (water, gas and solids) are discussed in some detail."

Jan 1, 2014

By Gregory A. Johnson

Operations and Maintenance departments have long had an adversarial relationship. The widespread evolution and adoption of modern management techniques such as Reliability Centered Maintenance (RCM) and Lean Production however has driven interest in working co-operatively to optimize overall plant performance. Mining and minerals operations have long adopted RCM in maintenance, and are now adopting Lean throughout the organization. Modern management initiatives like these explicitly call for co-operation between the two disciplines of maintenance and production and many advances have been made in the realms of people and methodology. One area that has lagged behind in supporting these developments however is information systems. Enterprise Asset Management (EAM) systems in maintenance and newer Manufacturing Execution Systems (MES) in operations have not been truly integrated in the way needed. Complicated plants, different software architectures, continually changing conditions and many variables have lead to systems problems which have contributed to the maintenance/operations divide. Master data synchronization (the ?plant tree?) and integrated reporting of real-time data with transactional data are just two of the issues that are being solved by new approaches in information technology including web services and service orientated architectures. New technologies are coming on-stream to enable the final ?bridging of the gap?.

Feb 1, 2008

By A. S. H. Kabir

Due to the high specific strength and excellent corrosion resistance, Ti-6A1-4V has been widely applied in aerospace industries. In this study, the welding performance of 3.2-mm and 5.1-mm thick Ti¬6A1-4V sheets was studied using a 4 kW continuous wave Nd: YAG laser. It is found that the use of filler wire, matching the parent metal composition, can bridge the joint gap and produce full penetrated welds up to a width of 0.6 mm without cracking. The laser welds were characterized in terms of the bead geometry, defects, microstructures, and hardness. With increasing joint gap, the percent porosity area increased, reaching just over 1% of the fusion zone area at a gap width of 0.6 mm for the 3.2 mm and 5.1 mm thick sheets. The maximum underfill depth in the Ti-6A1-4V laser welds was about 5% or 7% of the sheet thickness for the 3.2-mm and 5.2-mm thick materials, respectively, meeting the AWS D17-1 specification. The microindentation hardness was maximum in the fusion zone and sharply decreased through the heat affected zone until reaching the base metal value.

Jan 1, 2011

By Faan Bornman

"Reeves and Platt1 stated that dense medium separation is one of the most complex unit processes in mineral processing today particularly if cyclones are used. It is also the most efficient gravity concentrating process available to process engineers. The complexity of the process and large number of design and operating variables means that the process has largely remained more an art than a science. Dense medium separation is well established in the diamond, coal and iron ore industries but is gaining popularity as a pre-concentration step in other industries. The maintenance issues are addressed that will affect the efficiency of the operation.INTRODUCTION The purpose of the dense medium separation (DMS) process is to separate the valuable material from the waste based on gravity differences. However, the specific gravity difference between the two fractions must be large enough to achieve high efficiencies. Heavy particles sink through the dense liquid and light particles float. DMS is also used for the pre-concentration of minerals before further downstream processes like communition, in order to minimise the treatment costs. Examples are the pre-concentration of diamond ores or metalliferous ores like nickel, copper and cobalt. Dense medium separation is also used to upgrade the material to meet different market specifications, for example in coal and iron ore applications. A typical dense medium separation process for a diamond application is shown in Figure 1."

Jan 1, 2014

By T. Holmes, J. Middlemiss

"Agnico-Eagle (AE) has been operating their Kittila Mine in Northern Finland since 2008. The mine has experienced considerable ore flow problems with ratholing, bridging and freezing in their mill feed bin since start up. In the first winter of operation, the entire central portion of the contents of the cylindrical flat-bottomed 2000 tonne mill feed bin froze. Flow was erratic and could only be achieved through small diameter ratholes. To maintain a reasonable, albeit limited, feed to the mill, the bin had to be kept less than ½ full and a portable steam generator was brought in to melt the frozen agglomerates that frequently blocked the outlets. The combination of limited surge capacity and frequent outages required the crushing plant to operate 24/7 and resulted in inconsistent production levels and high operating costs.AE had planned to expand the processing plant to increase throughput by about 30% when they transitioned from open pit to underground ore. These plans presented an opportunity to improve the material handling.To avoid the problems experienced with the original mill feed bin, AE enlisted Jenike & Johanson Ltd. (J&J) to test samples of the ore, and based on the measured flow properties to provide design recommendations to ensure that the new mill feed bin would operate reliably. The new 2000 tonne expanded flow mill feed bin and apron feeder were installed in 2014 and are now supplying almost 93% of the total mill feed with the remaining coming from the original bin.IntroductionIn early 2009, AE engaged J&J to visit their then recently opened Kittila mine and mill in Northern Finland (Figure 1). Over the first half-year of operation, production had been restricted in the ore handling and storage system by flow problems such as ratholing, bridging and freezing including blockages of chutes and hoppers as a result of frozen fines buildup and large frozen agglomerates. AE wanted to increase production in the existing open pit mine and mill feed operation and also wanted to avoid similar ore handling problems when they commissioned the new underground mining system under development at that time."

Jan 1, 2017

By Brad Marchant, Rick Lawrence, David Kratochvil

"BioteQ has successfully developed commercial operations for ARD treatment and selective metal recovery using the patented BioSulphide and Thiopaq® biological reduction technologies. The BioSulphide-Thiopaq process was developed to provide biogenic sulphide for the selective recovery of high purity metal concentrates from acidic wastewater, which are sold to recover capital costs and off-set water treatment costs. The BioSulphide-Thiopaq process can be used on a stand-alone basis or in conjunction with a lime circuit. Process advantages include: selective recovery of metals, very low metal concentrations in effluent, reduced waste sludge liability, reduced lime treatment costs and, in some cases, profitable sale of metal concentrates. Two case studies are presented to illustrate operations focused on metal recovery at the Caribou Mine, New Brunswick, Canada, and at Phelps Dodge, Arizona. A third case study is presented to highlight environmental control as well as metal recovery for treatment of ARD at the Raglan Mine in Northern Quebec. Process flowsheets, capital and operating costs are presented for the three case studies.INTRODUCTIONProtection of water quality has become one of the most important environmental challenges facing the mining industry. Although new mining projects can be designed to minimize impacts to the environment, many existing and abandoned mining operations have water quality problems. The principal cause of water contamination is acid rock drainage (ARD), which is generated when residual sulphide minerals in waste rock, tailings and other mine components and products are exposed to air and water. These reactions can produce acidity and elevated concentrations of metals in drainage and seepage that can adversely affect surface and groundwater resources. To meet regulatory criteria for water quality in the receiving environment, many mine operators must consider treatment of mine water and other effluents prior to discharge."

Jan 1, 2003

By Julian Boldy

"A review of lI5 significant volcanogenic massive sulphide discoveries in the Canadian Precambrian during the past 65 years reveals that only 7% resulted from surface exploration methods aimed at depths below the effective reach of current geotechnical systems. This has been due to the relative ease of shallow discovery, resulting in the harvesting of ore deposits within 100 m of surface. This surficial layer has been more or less effectively supersaturated by routine exploration. In view of the fact that a mining district&apos;s metal content is not likely to be confined to a surficial layer, the time has come to explore the vertical dimension, prospecting for ore at depths in excess of 150 m in productive districts.Essential to this task is an understanding of the Precambrian volcanogenic ore deposit model. The deposits generally have .a tendency to be associated with the terminal phases of felsic volcanism, and to be located along certain time-stratigraphic horizons, marked by the products of volcanic exhalation. The significant massive sulphide deposits are discrete entities, ranging from the top 5% of deposits greater than 45 million tonnes in size, with a surface area of 0.30 km2, to median-sized deposits greater than 1.2 million tonnes in size with a surface area of 0.02 km2. These significant economic ore deposits range in value from $5.5 billion for the top 5% of deposits to $125 million for median-sized deposits. In terms of their frequency of occurrence, the former group has a 4% distribution and the median-sized deposits have a 15% distribution.An historical review of many of the principal Precambrian mining districts, such as Noranda and Flin Flon, shows that major tonnages are usually discovered during the initial phase of application of each new geotechnical search system, until carried to its ultimate limit of effective depth penetration. With the exception of the Noranda district, the mean depth of ore discovery in the other districts is still generally confined to within 50 m of surface.Targeting deep ore is difficult. One effective prospecting method is the detection of fracture-controlled mercury leakage haloes in outcrop (or core) above and peripheral to blind deposits. This technique has proved to be a useful pathfinder, and focuses attention on deposits buried at depths in excess of 700 m in some instances. Down-hole EM systems also promise to be effective in locating deposits previously bypassed by drilling. In addition, trend surface analysis programs of trace element geochemistry should be used as an aid to targeting ore by directing exploratory drilling along the plane of ore-hosting stratigraphy.By definition, mining districts have a proven ""favourability"" for the occurrence of ore. Discovery probabilities in these districts will be considerably enhanced if future search efforts are concentrated below a depth of 150 m, and more use is made of ""deep"" ore search systems coupled with sound geological reasoning. Deep drilling programs to a depth of800 m should initially be designed to search for the top 25% of deposits greater than 3.3 million tonnes in size, with a surface area of0.05 kmt. :a value of$310 million and a 12% frequency of occurrence; This can be accomplished for an over-all cost approximating $40,000 per drill hole. If the search depth is limited to 400 m, the over-all cost of each drill hole is $20,000, equivalent to expenditures routinely allocated to grassroots exploration drilling in the remote greenstone belts of the Precambrian. Depending on a company&apos;s objective, prospecting for deep ore offers a stimulating challange - though risky, it has its rewards."

Jan 1, 1981

By F. Rashchi, A. Ghahreman, J. Moghaddam, S. Karimi

"In this work, the kinetics of ferric-ferrous redox reaction on a passivated sphalerite electrode is studied by the application of chronoamperometry method in 0.5 mol L-1 H2SO4 solution. The electrochemical behaviour of ferric and ferrous couple was investigated on two sphalerite minerals acquired from two different geological regions (Iran and Canada). The carbon paste electrode (CPE) of sphalerite was initially prepared and passivated in 0.5 mol L-1 H2SO4 solution and after reaching the steady-state condition, ferric and ferrous sulfate solution was added. The registered current density differences between the current density of the passivated electrode and that of the electrode in the iron salts added solution were interpreted for kinetics of ferric-ferrous reduction-oxidation reaction. The equilibrium potential for ferric-ferrous couple on sphalerites surface was about 500 mV vs. Ag/AgCl. The exchange current density (i0) for ferric-ferrous redox reactions on the sphalerite samples had the same magnitude of 10–6 A cm–2. The electrochemical impedance spectroscopy (EIS) measurements at 550 mV vs. Ag/AgCl illustrated that sphalerite oxidation was controlled by two charge transfer process in both of Fe-free and Fe-containing solutions. The charge transfer resistance remarkably decreased when Fe salts added to the 0.5 mol L-1 H2SO4 solution, owing to the ferric-ferrous redox reactions being the predominant reactions on sphalerite surface.INTRODUCTION Direct atmospheric leaching processes for sphalerite concentrates are performed by reduction of an oxidant (e.g. ferric ion and oxygen) and oxidation of sphalerite to zinc ions. Oxygen could be an oxidizing agent as well, but the concentration of oxygen is very low in the solution. The role of ferric ions is predominate in this oxidation (Babu, Sahu, & Pandey, 2002). The oxidation reaction for sphalerite in the presence of ferric in can be presented as follows (Lampinen, Laari, & Turunen, 2015):"

Jan 1, 2017

"The Ernest Henry Mining (EHM) ore body is an iron oxide copper gold deposit with an average grade of 1.1 percent copper, 0.5 g/tonne gold and 22 percent magnetite. At the end of 2009, EHM converted the ball mill media charge from forged steel to high chrome media. At high pH values (above 10.5), forged media is passivated, so as the pH of the system drops the media corrosion rate increases and floods the system with corrosion products, affecting flotation. As the high chrome media is much more inert, pH has less of an effect on copper flotation response. Given this, the pH in the roughers was dropped from 10.6 to 9.6 and it was found that there was a slight increase in copper recovery and no statistical change in either the rougher or final copper concentrate grades for copper and gold. With the reduction in pH, there was a noticeable reduction in lime usage from 0.85 kg of lime per tonne of ore processed to 0.55 kg/t. This reduction in lime is equivalent to approximately $700,000 per annum at current production rates.INTRODUCTION The Xstrata Copper Ernest Henry Mine (EHM) is situated 38 km north east of Cloncurry, Australia. The mine began as an open-cut operation in 1998 and transitioned to a multi-sourced operation in December of 2011, utilising ore from the newly completed underground mine in addition to ore mined from the Mount Margaret Mining operations. EHM produces a combined copper gold concentrate containing 25 000 t of copper and 35 000 oz of gold annually, utilising a three stage grinding circuit along with a four stage flotation circuit. In addition to this EHM also produces 1 000 000 t of magnetite concentrate annually via a further grinding and three stage magnetic separation circuit. Based on metallurgical test work performed by Magotteaux between 2002 and 2008, the step to change from forged steel media to 18 percent chrome media was taken in 2009 in a bid to alter the pulp chemistry to improve the flotation performance in the plant (Greet, Kinal, Twomey, & Peatey, 2010). This plant trial resulted in: • Increased dissolved oxygen levels within the pulp, • A ball mill discharge Eh shift of 25 mV to more oxidising pulp potentials, and • An EDTA extractable iron percentage reduction. These improvements in the pulp chemistry resulted in an increase of 1.7 ± 0.6 percent in copper recovery and an increase of 2.9 ± 1.7 percent in gold recovery. As the plant trial using high chrome media was successful, the use of the media was adopted as the standard for the ball mill. This implementation opened the door for further process improvements around the flotation circuit."

Jan 1, 2014

"Generation and removal of fines are considered in the context of the mill and classifier as a single-unit process in which grinding rates and mechanisms, mill residence time distribution, circulating load, and classifier performance all interact to effect the overall grinding circuit productivity. Required process design specifications are identified, and a computer assisted design procedure for application of hydrocyclones in closed circuit grinding is presented. INTRODUCTIONThe purpose of the grinding circuit is to carry out the size reduction necessary to suitably prepare material for the upgrading process(I) The desired product size specification being the d1st1nguishing criterion between the ""fines"" (smaller than desired product size) and the ""coarse"" fraction (larger than desired product size), the capability of the grinding circuit to perform its task effectively depends on the nature of two processes that are taking place;(a) size reduction of the coarse material, and,(b) removal of fines from the system."

Jan 1, 1984

By G. P. Gormley

"Future open pit metallurgical coal mines in western Canada will be developed in complex geological environments. The success of these operations will be influenced by the mine operators&apos; ability to prepare accurate mine plans and to predict and, subsequently, 10 control both out-of-seam dilution and coal recovery. Quintette Coal Limited has been mining its tightly folded and severely faulted Mesa depo sit at annual rates of up to 9 Mt of raw coal, since October 1982. Ongoing development drilling combined with continuous utilization of blast hole information, has been required to achieve an acceptable geological data base for short range mine planning. Thrust faulting has been a primary geological cause of difficulty in selectively mining waste and coal, which has resulted in higher than expected dilution in plant feed. The same geological phenomenon has also increased reserves by 6.3% and allowed for expanded mine plans to include a lower thrust plate, ultimately doubling the mines original reserve base. This paper illustrates the geology of the Mesa deposit and the type of work involved in its interpretation. Regional GeologyThe Quintette Coal Limited (QCL) property is located in the Peace River Coal Field of northeastern British Columbia. In this area, northwesterly-trending folds of the Rocky Mountain foothills are commonly cut by multiple, low-angle thrust faults, which dip to the southwest. The Lower Cretaceous Gates Formation, of near shore continental origin, contains 5 to 7 mineable seams of medium volatile bituminous metallurgical coal (Figs. I and 2). These seams normally range in thickness between 0.75 m and 9.5 m and have an aggregate thickness of between 15 m and 22 m."

Jan 1, 1988

By Brad Sampson

Project Ownership ?Discovery Metals Limited ?ASX (DML), BSX (DML), AIM (DME) ?Market Cap AUD 195M ?Key assets ?Boseto Cu ?Dikoloti Ni The Boseto Copper Project ?Location ?Setting ?History ?Status ?Future

May 1, 2010