Search Documents

"Sink-float analysis is often used to obtain yield-ash and density partition curves in the coal industry. These provide a valuable tool for evaluating the performance of a separation process. However, for dense minerals, obtaining complete grade-recovery and density partition curves is more difficult due to the lack of heavy liquids available with the required densities. This paper examines a potential solution to this problem which is to perform batch fractionation of mineral samples in a laboratory-scale REFLUX™ Classifier using high viscosity fluidising liquids. The REFLUX™ Classifier is a gravity separation unit consisting of a system of parallel inclined channels positioned above a vertical fluidised bed. Operated in semi-batch mode, a charge of particles is fluidised from below and particles up to a certain density are elutriated from the top of the system. The fluidisation rate is then increased incrementally to fractionate the sample at progressively increasing densities. Previous work by Hunter et al. (2014) and Iveson et al. (2015) has shown that this method provides excellent agreement with yield-ash and partition curves for coal, especially when glycerol solutions are used as the fluidising liquid. This approach has now been extended to obtain the grade-recovery and density partition curves of high density mineral samples. This method has the potential to provide the minerals industry with an effective tool to evaluate the performance of unit operations separating at cut points higher than the available heavy liquids.INTRODUCTIONMeasuring efficiency and effectiveness is of key importance in the continuous improvement of mineral processing plants. For density based separation, one way the performance of a process can be evaluated is the measurement of density-based partition curves. Currently, this is done in the coal industry using the sink-float method, where heavy liquids are used to fractionate particles into discrete density intervals. However, with high density minerals such as iron ore, liquids of sufficient density are rare, and in most cases also pose serious health and safety concerns to laboratory operators. Most commercial laboratories do not perform sink-float separations above a density of about 4400 kg/m3, the maximum density of Clerici solution without operating at excessive temperatures (Koroznikova, Klutke, McKnight & Hall, 2007; Rosenblum, 1974)."

Jan 1, 2016

By H P. Tardif

This paper briefly describes some of the phenomena encountered when materials are submitted to extremely high pressures, such as those produced by the detonation of an explosive charge placed in contact with the material. It was found that extensive changes take place in the? microstructure of iron and steel. Diffusion-controlled processes, such as the transformation of lamellar pearlite, the recrystallization and grain growth of ferrite, and the homogenization of the pearlite-ferrite structure, can take place within micro-or milliseconds. Mechanical twins can propagate without deviation from ferrite to pearlite, thus indicating a proeutectoid ferrite-pearlite-ferrite orientation relationship. The propagation and interaction of intense stress waves in materials was demonstrated with the use of Armco iron. Finally, a comparison is made of the damage produced in metals by the formation of craters made by explosive shock and by hypervelocity impact. D DRING the last few years, exceptional development has taken place in the field of explosive metallurgy, i.e., the

Jan 1, 1964

By S. N. Rossovsky

"A new method for the hydrometalfurgical treatment of refractory gold arsenosulphide concentrates is presented. Themethod involves a combination of' finegrinding, intensive agitation, flotation, and cyanidation, and consists of leaching of -10u pyrite and arsenopyrite particles in alkaline solution under intensive agitation without the application of costly high-pressure and roasting techniques. Consistent extractions of gold, in excess of 96%, are achieved.IntroductionConventional methods of alkaline leaching of gold arsenosulphide concentrates in an autoclave» and under electrochemical oxidation( 2) require expensive equipment as well as high-cost energy and reagents. In other cases, processing of gold concentrates inelude: ultra-fme grinding, calcination at 200°C to 250°C with the addition of an oxidant (NH4NOJ followed by alkaline leaching of the resulting calcine with hydrogen peroxide, the latter being a complicated method yielding poor extractions of gold (89% to 90%). In this paper, a hydrometallurgical method is described for processing refractory gold arsenosulphide concentrates in which alkaline leaching is followed by cyanidation of the residue."

Jan 1, 1993

By A. R. Trusiak, C. Bazin, D. Hodouin

"The On-Stream Analyzer has proven, and is still proving to be, an extremely valuable tool for the control of flotation circuits. This paper examines the possibility of going further in the utilization of the analyzer results by using a real-time material balance program to calculate the mass flow rates within the streams of a circuit for process control, analysis and optimization as well as for the detection of sensor malfunction. The material balance algorithm improves measurements and give good estimates of unmeasured variables during normal operating conditions. The potential and limitations of the method are illustrated using results of an application to the Line 3 flotation circuit of Brunswick Mining and Smelting, New Brunswick.IntroductionThe On-Stream Analyzer (OSA) has gained, over the last two decades, the status of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant and its application in oxide mineral flotation plants isincreasing. Commercial OSAs include a sampling system that collectssamples from various streams of a circuit and exposes thesamples to an X-ray beam. The sample then generates X-ray pulsesthat are converted into assays using multilinear regression programs(Leroux and Franklin, 1994). The estimated assays arepassed to the flotation operators via operator consoles, or to controlloops of various degrees of complexity (McKee, 1991), whichmanipulate reagent addition, aeration rate or froth thickness toensure an adequate operation of the plant. Although this applicationrapidly pays for the purchase of the OSA, one should ask:""Could we get more from the OSA?"""

Jan 1, 1995

By J. P. Harrison, G. F. Gambino

"This paper examines unpredictability in the parameters governing hydraulic fracturing (HF) as used in stress amelioration for underground excavations, with the aim of showing how this unpredictability may affect design decisions. Using uncertainty models that are appropriate to particular levels of information and degrees of uncertainty, this paper demonstrates how these can aid in decision-making related to feasibility assessments of HF arrays for stress amelioration.Cave mining operations produce large underground voids and high stress concentrations around critical mine locations. These stress concentrations increase the potential for rock burst events. Although de-stress blasting has a long history for redistributing high stress concentrations, to improve safety and reliability HF is now being trialled as an alternative.Unfortunately the HF process is extremely uncertain, and so predicting fracture propagation geometry is difficult. Although the major parameters governing HF propagation have been previously identified, no indication has been given regarding the contribution that uncertainty in these makes to unpredictability in the overall HF system. Using simplified models of HF and referencing a recently proposed characterization of unpredictability, we relate unpredictability in the various governing parameters to the effect it has on strain energy density (SED) in the surrounding rock. Within these models we analyse SED as well as the stress intensity factor (KIc) when investigating the effect of parameter uncertainty and its influence on various crack propagation criteria (Sih & Macdonald, 1974). These models are applicable to unpredictability associated with the development of new fractures; the case of pre-existing fractures is the subject of on-going work.The paper will assess in greater detail the various governing parameters, and investigate the appropriate use of other uncertainty models. As a result, we will show how assessment of uncertainty in HF parameters can be used to both guide feasibility studies and determine the optimal allocation of resources to improve the final design."

Jan 1, 2015

By Don McColman

"Tires, although not always the largest single cost item in open-pit mining operations, will place in the top three, along with explosives and fuel. How this high-cost supply is controlled is dependent upon on an efficient tire program. The success of this program is, in turn, dependent upon the people who are directly associated with tires and their use, namely: the mine's tire personnel, the tire sales representatives and a technician for the rubber company. The technician will relay his observations and information received from the mine personnel back to the manufacturer with recommendations to overcome current problems .Haulage truck tire life and costs in a hard rock open-pit mine are governed and controlled by four important factors:I) Field control.2) Operating within manufacturer's guidelines.3) Different tire purchasing methods.4) Scrap piles.Field ControlPerhaps the most influential people involved in this program are those who live with the tire through every hour of its lifespan: the truck driver, the shovel operator, the dozer operator, the grader operator and the shift boss. Of these, the truck driver has the most control, in that he can drive over or around rock s as these situations arise. The loading area, the edge of the haul road and the dump account for most of the tire injuries.This is why shovel, dozer and grader operators must appreciate their influence on haulage tire life. Spillage cleanup must be ongoing and is not being done adequately if any of these operators are idle. The shift boss that drives by a rock on the road without removing it or calling for a cleanup has little recourse with the truck driver who runs over it-he has sanctioned the driver's actions by his own neglect."

Jan 1, 1986

By J. P. Jylhä, A. Jokilaakso

The Outotec Flash Smelting process is widely used in primary copper production. A layer of slag on top of matte (copper–iron sulphide melt) creates a barrier through which matte droplets descend. Droplets of different sizes settle through the layer at different rates, which increases possibility of copper losses as smaller matte droplets may be removed with the slag. In this work CFD-DEM (computational fluid dynamics – discrete element method) coupling was used to simulate matte droplets settling through the slag during slag tapping. Discrete droplets and slag flow were simulated with DEM and CFD, respectively. This new approach enables tracking and solving movement and interactions of individual droplets. User-defined models were created to take coalescence and reaction kinetics into account. Coalescence created larger droplets, while the reactions decreased droplet size and increased its density. Drag caused funnelling effect, which pulled droplets towards the centre line of the descending cluster. This research is the only study known by the present authors in modelling liquid-liquid systems with the CFD-DEM coupling. Simulating coalescence and chemical reactions for discrete droplets enables more realistic simulations. However, CFD- DEM simulations are computationally resource intensive already without additional models, so a full scale industrial settler modelling still waits for further increase in computer performance. INTRODUCTION Flash smelting is a method used in copper and nickel production. In the flash smelting process, oxidation of sulphides in a concentrate is used to release energy needed to smelt the feed. In the process, copper matte is formed. Matte has copper content in the range of 55 – 70% (Sridhar, Toguri, & Simeonov, 1997), the rest is mainly sulphur and iron but has still many other impurities (Taskinen, Seppälä, Laulumaa, & Poijärvi, 2001). Oxidized iron forms iron-silicate slag while SO2 is collected for acid production (Davenport & Partelpoeg, 2015). The Outotec flash smelting furnace (FSF) can be divided in four major component: concentrate burner, reaction shaft, settler and uptake. Concentrate, flux and oxygen enriched air are injected into the reactor through the concentrate burner. The mixture then reacts in the reaction shaft forming matte and slag, which are collected in the settler, while off-gases flow out of the reactor through uptake for heat and dust recovery, and SO2 collection for H2SO4 production. The matte and slag form separate layers due to immiscibility and density difference. Raw material feed is continuous, but the matte and the slag are tapped periodically. A flash smelting furnace is depicted in Figure 1.

Jan 1, 2019

By P. A. Peach, W. H. Gross

The modern economic geologist in Canada is well equipped to apply geological, geochemical or geophysical techniques in the exploration for ore. Recently, great advances have been made in geophysics and geochemistry, and a large number of new orebodies have been discovered by these methods. An attempt is made in this paper to show that there has also been a considerable advancement in geological knowledge and that the most effective application of geophysics and geochemistry often occurs in areas already considered geologically favourable for the occurrence of ore. Ali exploration methods sooner or later suffer from diminishing returns. Therefore, as time goes on, one can expect to see the application of some of the more subtle or refined geological techniques that are presently being developed.

Jan 1, 1967

By W. C. Ferguson

"This paper could be more appropriately titled ""The Application of Vacuum Filters to Underground Minewater Treatment. in a previous paper co-authored by the writer (1) the history and development of minewater treatment at the Sudbury District Operations of the International Nickel Company was outlined. It is the intention of this paper to dwell more specifically WIth the the application of the vacuum filter to a problem found in most, if not all, underground mining operations. In the preparation of this paper the writer has made liberal use of the illustrations and text of the paper previously noted.Last year we heard Mr. Nemeth discuss the basic mechanisms involved in vacuum filtration (2), and today Yr. Cunliff has exposed us to the selection of the filter media (3). I will now briefly review the various vacuum filter designs that generally lend themselves to metallurgical dewatering applications.DRUM FILTERSThe revolving drum-type which filters on its outside periphery is illustrated in Fig. 1. This is the Oliver or Drum filter and represents the first commercially available continuous vacuum filter. The original design dates back more than 50 years, but with the exception of the method of discharge, is identical to the units being marketed today. This filter is generally applied to slow filtering slurries. The cake may be discharged in several ways; strings, scraper blades, rolls or by passing the filter cloth over a small diameter discharge roller (belt discharge).THE DORRCO FILTERThe revolving drum type which filters on its inside periphery is illustrated in Fig. 2. Here the slurry lies in the drum and the cake discharges through a chute or conveyor. This type of filter is most often applied to fast-filtering slurries.THE DISC FILTERThe revolving filter which filters on the vertical plane of the disc is referred to as the Disc or American-type filter. This represents the most inexpensive design in terms of cost per square foot of filter area. This filter is widely applied, but is probably more suitable for slower draining pulps."

Jan 1, 1971

By Erica J. Wanless, Ghislain Bournival, Seher Ata, Jose Hamilton Tavares

In froth flotation valuable particles are captured by bubbles and transferred to a froth layer where bubbles are in close proximity. Bubble coalescence frequently occurs in flotation, especially in the froth layer. The coalescence of two bubbles causes a release of energy, which may expel particles from the bubble surface. A series of experiments were carried out to determine the effect of bubble interfacial properties on the detachment of particles upon the coalescence of capillary-held bubbles of 2 mm in size. The interfacial properties of the bubbles were changed by the addition of low molecular weight alcohols, namely 1-pentanol or methyl isobutyl carbinol (MIBC). Using esterified glass particles (? = 43 °) with a 10 % and 90 % cumulative passing diameter of 47.2 and 92.5 µm, respectively, as model particles, it was found a certain concentration of frother, different for each additive, is needed in order to observe a reduction in the detachment of particles. In the presence of frother, the detachment was evaluated at approximately 65 % which was a considerable reduction in the detachment compared with the value of approximately 85 % found in the absence of frother. Frother molecules changed the properties of the airwater interface. Upon the coalescence of two bubbles, the release of energy caused the merged bubble to oscillate; effectively resulting in the detachment of particles. The addition of frothing agents augmented the elasticity of the bubbles, which appeared to be related to the detachment of particles. Whereas frothing agents are generally used to prevent bubble coalescence and stabilise the froth phase, only transient stability is imparted. The results suggested that an additional role of frothers in flotation is to decrease the detachment of particles from bubble surfaces. The type and concentration of frother can be strategically selected to improve metallurgical recovery as an economic incentive.

Jan 1, 2016

By D. Saramak, Z. Naziemiec

"Chalcedonite is an unique rock due to the relatively small area of its occurrence. It also possesses multi-raw-material features therefore it should be given a special protection aiming at its complete and optimal utilization. It is the natural sedimentary rock and the only mine in Poland, located in Inowlodz, where the opencast mining from “Teofilow” deposit is carried out.Chalcedonite mainly consists of cryptocrystalline and microcrystalline chalcedony together with small amounts of autogenous and detrital quartz. The chalcedony itself is a fairy common mineral and many forms of its occurrence is known, some of them are semi-precious minerals. Among the most popular ones following can be found: agate, bloodstone, onyx, carnelian, chrysoprase. Many countries own chalcedony deposits: Australia, Brazil, India, Canada, Namibia Russia, South Africa. However chalcedony in its pure form does not occur in the mentioned chalcedonite rock. The pores, which take usually from 5% to 25% of volume and have sizes smaller than 0.5 mm, are the characteristic feature of all chalcedonite forms. The paper presents some crucial problems of its processing together with most significant directions of its applications. New method of chalcedonite enrichment based on densimetric separation (patented in Poland) is presented. Results of investigation show that the obtained products can increase quality of concrete and filter grits."

Jan 1, 2016

By T. Lux, H. -J. Krassnig, I. Filzwieser, E. Hecker, R. Degel, A. Filzwieser

Non-ferrous metals find their applications in smartphones, tablets and computers. These materials with their particular properties are the basis of our modern life. SMS group is well prepared for this huge market and for growing future challenges. A large contribution here is the new joint venture PolyMet Solutions that was founded by SMS group and Mettop, an Austrian engineering company, with the objective to develop new technical solutions for the primary copper production lines as well as for non-ferrous metals starting with the primary smelting of concentrate and ending with the electrolysis. PolyMet Solutions provides the process know-how whereas SMS group supplies the plants and equipment and Mettop the key components. SMS group and Mettop also cooperate in the field of tankhouse technology. Together with Montanwerke Brixlegg AG, Mettop has developed together with a parallel flow technology (METTOP-BRX Technology), allowing a current efficiency of above 98 % at a current density of 420 A/m², which is a milestone in copper electrolysis. For the secondary copper production route, SMS group and PolyMet Solutions developed an innovative refining furnace (PolyRefine) for the smelting and refining of copper scrap. The refined copper is directly charged to the Contirod line to produce copper rods and wires. The innovative cooling solutions of SMS and PolyMet Solutions come into play where furnaces have to stand the highest loads and stresses, for instance in areas of very high temperatures or temperature fluctuations, aggressive exhaust gases and slags, or at critical spots such as taphole areas. Custom-tailored cooling systems for furnace vessels make sure varying loads are compensated in a targeted and effective manner. The solutions include air cooling, spray cooling, cooling technologies with integrated copper elements such as CFM (Composite Furnace Modular) cooling systems, plate and finger coolers. The major innovation in the field of furnace cooling is the ILTEC (Ionic Liquid Cooling) Technology which paves the way for increased plant safety. This revolutionary, patented cooling technology is jointly marketed by Mettop and SMS group. It permits water-free cooling to be implemented and thus makes operation safe wherever it is applied. INTRODUCTION Non-ferrous metals or NF metals are changing the world. There is no modern industrial sector that can do without these valuable metals. Non-ferrous metals find their applications in smartphones, tablets and computers. These materials with their particular properties are the basis of our modern life. The importance of the non-ferrous metals market is reflected by two figures. In 2018, the production of non-ferrous metals was worth more than 237 billion Euros. This contrasts with 255 billion Euros of the value of iron and ferro- alloy production in the same year (International Organizing Comittee for the World Mining Congresses, 2018). Hence, the NF metal industry is almost as important as the iron and steel industry. SMS group is well prepared for this huge market and for growing future challenges. A large contribution here is the new joint venture PolyMet Solutions that was founded by SMS group and Mettop, an Austrian engineering company, with the objective to develop new technical solutions and to enhance customer value. The prices of nearly all metals have come under pressure during the past few years. Therefore, competitive technologies are regarded a crucial factor to achieve success in this critical market situation respectively to stabilize the market position.

Jan 1, 2019

By P. J. Sylvester, S. J. Piercey, S. Maloney, S. M. Brueckner, L. Pilgrim, D. Hyde, G. Ogilvie

The 1806 zone is part of a Au-rich volcanogenic massive sulfide deposit at the Rambler Camp on the Baie \/erte Peninsula, northwestern Newfoundland, and is characterized by high Au grades (3.97 g/t), relatively low Cu and Zn grades (0.60 wt% Cu, 1.17 wt% Zn), and moderate Ag grades (27.83 g/t) at ca. 0.37 Mt ore. Gold and Ag occur as electrum and different Ag varieties including Ag-Hg ± Au alloys, miargyrite, and pyrargyrite that occur often in close proximity to electrum. Additionally, Ag-, As-, Sb-, and Sn-bearing sulfosalts are frequently observed and usually close to electrum. These textural relations strongly favor a syngenetic/magmatic origin for the 1806 zone, despite having a metamorphic overprint.

Jan 1, 2011

By L. Bichler, A. Siebert-Timmer

In this research, novel YSZ ceramics doped with 5 mol% Nd2O3 were manufactured via Spark Plasma Sintering (SPS) process. The sintered Nd2O3-YSZ ceramics were subjected to a static supercritical water environment at a temperature and pressure of 400 °C and 31 MPa, respectively. The weight loss and microstructure development of the sintered ceramic before and after exposure to supercritical water was studied. The results suggested that Nd2O3 addition significantly improved the degradation resistance of the YSZ ceramics. This was attributed to the improved phase stability of the 5 mol% Nd2O3-YSZ ceramics, since X-ray Diffraction (XRD) studies showed that the cubic stabilized matrix in these ceramics was retained after exposure to supercritical water. In comparison, pure YSZ ceramics exhibited a rapid degradation behavior as well as a phase change.

Jan 1, 2014

By James F. Archibald

Testing has been accomplished to substantiate recent laboratory trials which have demonstrated that thin liner membranes, applied to rock core samples, can significantly enhance the structural performance of such rock materials. A range of Canadian polymer liner materials (MineguardTM, RockguardTM and RockWebTM) have been tested side-by-side to evaluate strength and other physical property improvements generated for two highly homogeneous, though differently sourced, granodioritic rock materials. Tests were conducted on physically similar core materials, utilizing 104 to 113 samples of each respective rock type. For both rock sample populations, cores were coated using linings at thicknesses varying between 1 and 7.3 mm, typical of the application range currently used underground by mines contemplating use of such membrane agents. Results of rock failure tests, following application of passive lining covers upon the very large sample populations of each rock type, have indicated that noticeable strength improvement and enhancement of post-yield failure characteristics can be developed by the entire range of spray-on liner materials evaluated. It is shown that all of the tested liner agent materials currently available can and do act to positively reinforce rock support capabilities of modeled core pillars. Where liner materials can be effectively placed underground, it is anticipated that they may provide similar benefit and be successfully used in partial replacement for either screen or shotcrete to provide advantageous area support for rock.

May 1, 2001

By Neillm Alastair S.

"This paper looks at what has happened in the past decade in the rare earth industry, particularly for those companies outside China trying to develop alternative projects to the Chinese dominated supply chain. The rare earth industry has gone through a metamorphosis over the past decade. The industry was basically unknown outside China until overnight it became the next hot topic on the financial streets of Canada and Australia. Suddenly various junior miners shifted from uranium and other out-of-favor commodities to rare earths as funds were easy to access from an investment community that did not understand the complexities of the space. The initial funding was done on traditional junior mining metrics of grade and deposit size. This has morphed over time to:1) Lights versus heavies2) Making a concentrate3) The importance of separation4) Off-take agreementsAt the peak of the market frenzy certain flagship operations were built using the “Not Made in China” moniker. Unfortunately certain errors were made during implementation, which are finally coming to the surface and making the rest of the pack wondering what will happen next. A review and update of some of the mistakes made and lessons learned will be discussed.BACKGROUNDAbout ten years ago awareness started to form around the rare earth industry and various groups recognized that because of the closure of Molycorp, Mountain Pass, and the dominance of China, there was a risk of uncertainty of reliable supply. This was not news for those active in the industry like Rhodia (now Solvay), the Japanese, South Koreans and other key consumers but to others it was like a light went on and rare earths became the new “.com” trend for investment banks, investors and some mining companies looking for the next hot topic.In the late 1990’s Molycorp accounted for around 20-25% of the world’s supply of rare earths, mostly lights (La, Ce, Pr and Nd), with small amounts of heavies from other sources. Then environmental issues forced the closure of the operation at Mountain Pass. Within six months China had increased production to plug the gap in supply. Around that time China was developing a strategy to leverage their position in rare earths and implemented a series of regulations to increase the value added component of rare earths inside China."

Jan 1, 2016

One Data Set for the Lifecycle Complete data captured at the logging stage benefits the entire life cycle Exploration Technical Studies Production and Milling Visible Light Spectrum Hyperspectral, put simply, is the interaction of light with matter based on the nature and chemical structure of the specimen. SpectrumWe develop the library to match the liberation size fraction Analyses every 1mm2 1 meter of NQ core = 35 000 analysis data Crystal size detection : 0.1 micron

May 1, 2013

By Michael L. Free, Zongliang Zhang, Joshua M. Werner

In the copper electrowinning process, short-circuiting between the anodes and the cathodes is a critical problem that changes the current allocation among local electrodes and reduces the current efficiency significantly. Possible reasons for the short-circuiting include the improper alignment of the electrode, bent electrode, and nodules on the cathode surface. In typical tankhouses, there is often a time between shorting and harvesting as well as between shorting and clearing. Therefore, it is inevitable to have short-circuiting affect the operation performance in practical electrowinning operations. However, one key piece of missing data is the actual measurements of the current efficiency as short-circuiting is approached and allowed to continue. Consequently, short-circuiting tests that allow tracking of electrowinning parameters before and after short-circuiting were performed in a laboratory scale Cu electrowinning cell. In the tests, the electrode spacing change, the mass of electrodeposited Cu, the deposition morphology, and the current allocation as well as the current efficiency before and after short-circuiting were studied. Results show that the short- circuiting affects the current allocation and the current efficiency significantly. Moreover, it changes the Cu deposition on the short-circuited cathode and therefore causes problems for Cu electrowinning. INTRODUCTION Electrowinning (EW) is commonly used for copper production around the world, with a rated production from 120,000 to 200,000 tons per year per operation (Wiechmann, Aqueveque, Henríquez, Muñoz, & Morales, 2014). In Cu electrowinning, Cu ions in the electrolyte are reduced on the cathode surface as metallic copper with a DC current, while on the anode, a counter anodic reaction occurs with oxygen gas generation (Werner, Zeng, Free, Zhang, & Cho, 2018; Zhang, Werner, & Free, 2018; Zhang, Werner, & Free, 2018). In copper electrowinning, an average current density of 200 to 400 A/m2 is applied to the electrowinning cell (Wiechmann et al., 2014). As the Cu deposits on the cathode, the distance between anode and cathode reduces and most of the time, short-circuiting forms between some anodes and cathodes in a large tankhouse containing thousands of electrodes, reducing the current efficiency and increasing the energy consumption significantly. The current efficiency in well-run copper EW operations is typically above 90 %. Most of the unused current is wasted through short circuits, stray currents, and by-byproduct formation (Davenport, King, Schlesinger, & Biswas, 2002; Wiechmann, Vidal, Pagliero, & Gonzalez, 2002; Wiechmann, Morales, & Aqueveque, 2010). Usually, in the tankhouse, the short-circuiting increases the current in the involved cathode by up to 1500 A (Wiechmann et al., 2010). Multiple reasons can cause the short-circuiting in the cell, and the most common reasons include the uneven current distribution among cathodes, tilted electrodes, bent electrodes, and nodules formed due to the large deposition roughness. Recognition of this challenge in the Cu electrowinning process has led researchers to perform many investigations on approaches to avoid and reduce the short-circuiting in the cell. A series of research investigations have been conducted to develop and improve a new type of intercell bar for Cu electrowinning (Wiechmann et al., 2002; Wiechmann, Morales, Aqueveque, & Burgos, 2007; Wiechmann, Morales, & Aqueveque, 2009; Wiechmann et al., 2010; Wiechmann et al., 2014). The associated test results show that this new design limits the occurrence and magnitude of short circuits and allows operation at higher current densities. Sandoval, Clayton, Dominguez, Unger, and Robinson (2010) stated several keys to control short circuits, such as maintaining the straightness of the cathode, removing “edge hair” from the cathode starter, and maintaining electrode alignment in the cell. Prengaman and Siegmund (1999) from RSR technologies developed a new Pb-Ca-Sn anode to prevent the anode deformation, thereby reducing the short-circuiting in the Cu electrowinning cell. Although the negative effects of short-circuiting on the Cu electrowinning have been recognized, and various investigations have been conducted to address this issue, the actual measurements of the electrowinning behavior and performance as short-circuiting is approached and allowed to continue are seldom reported. However, in typical tankhouses, there is a time between when shorting occurs and harvesting/clearing are performed. One key factor in determining the harvest time is the frequency of shorting. Consequently, we have performed short-circuiting tests that allow us to track electrowinning parameters before and after short-circuiting.

Jan 1, 2019

By X. Cao, X. -G. Chen, K. Liu

Due to the detrimental effect of platelet iron-rich intermetallics on mechanical properties (particularly ductility) in cast alloys, it has been essential to transform these phases into Chinese script morphology. In the present work, the effects of Mn and/or Si addition and cooling rate on the phase transformation of the iron-rich intermetallics in 206 cast alloys with different Fe contents ranging from 0.15 % to 0.5 % were systematically investigated. The results obtained showed that platelet ß-Fe and Al3(FeMn), Chinese script a-Fe, Alm(FeMn) and Al6(FeMn) can be observed in the 206 cast alloys, depending on the Fe, Mn and Si contents as well as the cooling rate. It was found that the addition of either Mn or Si favors the formation of Chinese script iron-rich intermetallics but inhibits the precipitation of the platelet phases. In addition, the combined addition of both Mn and Si has a synergistic effect on the phase transformation. Furthermore, there exists a critical cooling rate to effectively suppress the formation of platelet iron-rich intermetallics for a given alloy. The threshold cooling rate decreases with increasing Fe, Mn and Si contents. Casting process maps are established to correlate the intermetallics precipitated with alloy chemistry and cooling rate for 206 cast alloys containing various Fe levels.

Jan 1, 2014

By Gary M. Bone

The autonomous control of vehicles interacting forcibly with their environment, such as dozers and tractors, is an unsolved and challenging problem. Forces and motions are inherently coupled between the tool and the means of vehicle propulsion. Furthermore, they are often operated within uncertain and unstructured environments, such as those encountered in underground mining. There is a growing industrial interest in the development of robotic vehicles to improve productivity, efficiency and safety in mining and construction. This paper focuses on the modeling and control of autonomous robotic dozing for a material removal operation. A dozing process model has been developed based on observations of both a fullscale dozer and a scaled-down version. The model characterizes the dynamic interactions between the blade position, material accumulation on the blade, material distribution in the environment, and the motions of the dozer. The dozing control objective is to remove the loose material as rapidly as possible by driving forwards at full power while automatically raising/lowering the blade in response to sensor measurements. Two different controllers were developed to meet this objective. The first controller is based on a set of heuristic rules, and the second is an optimal controller based on the dynamic model. An instrumented scaled-down robotic dozer and dozing environment, designed to emulate the full-scale operation, are used to implement the controllers and compare their performances over multiple dozing passes. Experimental results are presented showing that the model-based controller increased the material removal rate by 33% compared to the rule-based controller. Lastly, technologies for full-scale implementation are discussed, followed by proposed future work and conclusions.

Aug 1, 2013