Search Documents

By Charles Amoah

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By P. Reyes

The Codelco Chile El Teniente Division Caletones Smelter has an objective to smelt 1,250,000 tonnes per year of copper concentrate. This is a great challenge for the smelter facilities and particularly for the acid plants. The analysis ensuring that there are no obstacles to achieve the production capacity was of great importance. Therefore a series of activities were undertaken as well as studies dedicated to reach the target. This paper presents work focused on a fluid dynamic study, translated in an operation methodology of integrated handling of the smelting and converting gases with the objective to optimize the gas flow and S02 concentration. The optimization should be done employing the current installations, equipment and instrumentation and/or minor modifications. In the first part of the work the condition of the instrumentation involved in the gas handling was checked, improvements determined and the corresponding corrective actions were carried out. The proposed operation method consists of operation of the Cleaning Gas Plant 2 (TC' s gases) and operation of Gas Cleaning Plant 1 (the remaining gas plus the gases from CPS). The implementation of the operation method involves the modification of the valve of the gas into the duct to plant 1 from On to Off to modulate flow. After modification a three days test was carried out. To evaluate the tests, a "Sulphur Capture" indicator was used. During the test the behaviour of the effluent treatment plants was closely examined. No problems or unusual operating conditions were observed. The reduced flow of gas to Gas Cleaning Plant No. 1 permitted the start up of the 2nd test day treating most of the gas received by Gas Cleaning Plant No. 2. The operation was carried out with the limitation not to increase the effluent pond level, which was maintained constant.

Jan 1, 2007

By B. K. Bhattacharyya, Morley. L. W.

"The primary purpose of conducting aeromagnetic surveys in mineral areas, and interpreting the data thus obtained, is to aid in the extrapolation of the geology from known to unknown areas-both in a horizontal and vertical direction. This paper describes one of the steps in the process of interpretation which has, in the past, been neglected-that of mathematically or quantitatively treating the data in two-dimensional map form. For this, several techniques are available.These techniques determine the downward and up-ward continuation fields, the second vertical derivatives and the fields reduced to the pole from the total magnetic field data. Second vertical derivatives and downward continuation fields increase the resolution and sharpness in the observed magnetic anomalies and tend to outline the surface traces of causative bodies with a reasonable amount of success in most cases. The 'reduction to the pole' is a mathematical process of calculating the field at the north pole from the observed field so that the un-desirable effects of the dip and declination of the earth's field and of rock magnetization are eliminated.New and accurate means of carrying out these calculations have been developed by the Geological Survey of Canada. In this paper are also presented the results of a method for obtaining the symbol and numerical map of the processed data with the help of the printer associated with the computer. The tedious work of digitizing magnetic field values in a map can be speeded up by the use of a semi-automatic coordinatograph, with the aid of which field values can be accurately transferred to punched cards."

Jan 1, 1966

By H. R. Banks

SHORTLY after the commencement of operations at the Sullivan concentrator, the use of a pilot table was instituted in order to present a visual control of various products by showing the amount of galena still present in the tailing from several stages of flotation. Among the products so treated, the final tailing was later included. It was sratifying to note that very little free galena was escaping, but a fine streak o a whitish mineral appeared at the concentrate zone. This mineral was identified as cassiterite. The amount was small and the newly recognized component in an already complex ore was considered primarily as of academic interest. However, the problem of recovering a usable metal was intriguing and, as opportunity presented itself in temporary lulls in research on Sullivan and other ores, the concentration of tin was a useful 'bit of knitting' to go on with. It was recognized from the start that the bulk of the mill tailing would have to be floated and the residue subjected to gravity treatment. Since one of the predominating features of Sullivan concentration operation has been the necessity of fine grinding, the problem of gravity concentration was thereby intensified. Several batch runs were made, and sufficient pulp was treated to produce about one ton of final tin concentrate assaying 67 percent tin. The overall recovery was under 30 percent and the estimated profit at full tonnage was only marginal. Testing was resumed several years later, when the price of tin again appeared attractive, in an attempt to develop a more compact plant with better recovery of tin. The weakness of the original plan of concentration was the large number of tables required to treat a feed so low in tin.

Jan 1, 1941

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By D. Roy Eccles

A multi-element geochemical response, with contrasts of up to 29 times background, was obtained in soil above the Mountain Lake Diatreme, northwestern Alberta. The overall geochemical signature is indicative of an ultramafic source; geochemical responses contain elevated concentrations of Co, Cr,O, Cu and Ni with the presence of high Ba, Ga, HI, PO,, Rb, Ta, Ti and light rare earth elements suggestive ofa kimberlite or lamproite body. The shape, or morphology, of the enzyme leach-based geochemical signature over the Mountain Lake Diatreme combines moderately strong to strong oxidation halos, or a rabbit's- ear geochemical profile, with a sharply-defined apical geochemical profile. Because some Alberta diatremes discovered to date form positive topographic highs, the resultant geochemical signature may express the soil development profile that forms directly on top of kimberlitic and lamproitic bodies. The enzyme leach technique, which has proven to be a useful tool in base metal, precious metal and petroleum exploration, may have a significant impact on exploration for kimberlite, lamproite and related rocks in Alberta by providing industry with a useful and cost effective tool to probe blind and/or buried anomalies identified by airborne and ground magnetic surveys in areas of glacial overburden.

Jan 1, 2001

By Guocheng Pan

"Although many factors play roles in the estimation of recoverable reserves, smoothing effect and conditional bias are considered major geostatistical issues in the estimation. This paper introduces measures for smoothing effect and conditional bias, and provides insights into their relation to the estimation of recoverable reserves. Both smoothing effect and conditional bias are intrinsic to the information effect and kriging estimators. For a given level of drilling information, however, it is possible to identify the optimal search radius that minimizes conditional bias. Furthermore, it is also feasible to define variance correction factor for reduction of the smoothing effect from exploration block models. Both of these components are key to the accurate estimation of recoverable reserves. IntroductionThe accurate estimation of recoverable reserves is critical to decision making in different phases of feasibility study and mine planning. Much attention for improving the methodology of estimation has been focussed on the effect of the change-of-support (Parker, 1980; Dagdelen, 1996). For example, it is essential to make a volume- variance correction to the estimate of multiple indicator kriging (Hoerger, 1992). When the size of block, b, in the geostatistical model differs from that of selective mining unit (SMU), v, a volume-variance correction is warranted for the prediction of recoverable reserves.Most mining plans and decisions are made prior to the availability of high density blast-hole samples. In most mining operations, the true SMU grade Zv is unknown at the time of selection. Instead, the selection is based on the estimate Z v**derived from high density blast-hole samples within the deposit G. Nevertheless, the estimate Z v * of recoverable reserves in the stage of mine planning is derived from exploration data. At the end, the production result must be reconciled to the estimate Z v * . In other words, the selection is based on Z v** from blast-hole samples, while the final production figures are reconciled to Z v * from exploration drilling. For a given preselected cutoff grade z0, the actual mining panels will consist of the units having the estimated grade Z v** =z0 rather than the true grade Zv =z0. The difference between Z v** and Zv is usually of less concern."

Jan 1, 1998

"The asbestos mining industry in the Eastern Townships of Quebec has early recognized the undesirable side-effects associated with mineral production, such as air pollution, noise and unsightly waste dumps. In order to efficiently achieve the industry's aim of eliminating or minimizing these objectionable features of mining, all of the asbestos producers in Quebec interchange information, knowledge and design dealing with the environmental control measures through the Environmental Committee of the Quebec Asbestos Mining Association.The paper describes what has been done and what is planned for the future in the various problem areas, such as control of dust emitted during the open-pit drilling operation, control of dryer stack emissions, control of the environment in ore, fibre and tailings handling operations, rehabilitation of the countryside covered by waste dumps, and many others."

Jan 1, 1971

By Claude Hubert, Alex C. Brown, Michel Richard, Rejean Sirois

"The Pierre Beauchemin gold deposit, situated 15 km NW of Rouyn-Noranda, produces an average of 1050 tonnes of ore a day. Reserves are 1.2 Mt grading 5.6 g/t Au. The deposit, located in a shear zone within the Flavrianpluton, in the Blake River Group, is hosted by four major rock types: meta-trondhjemite, meta-tonalite, hybrid rocks and meta-diorite (the prefu; ""meta-"" is omitted thereafter). The trondhjemite, tonalite, and metamorphic hybrid rocks are spatially distributed as a series of sub-horizontal tabular sills that form a genetically related group. Early fractures that permitted either the emplacement of pre-diorite felsic dikes or the formation of a visible alteration caused by early fluid circulation might have been developed in response to initial strain created during regional deformation. These fractures were precursors to the emplacement of diorite and the development of major shear planes. Sub-horizontal north-trending en échelon diorite lenses are observed at the mine. Together, these diorite lenses constitute larger scale diorite zones which are observed at the scale of the pluton. The diorite zones are interpreted as evidence of an episode of sub-vertical extension sustained by the layered trondhjemite, tonalite and hybrid system. The anisotropy created by the less competent sub-horizontal en échelon diorite was an important factor. In shear zone development and subsequent mineralization. The tonalite and diorite accommodated further defomation and developed the main N030°/40° ESE shears along with the spatially associated N060°/50°-60° SSE, and the N000°/10°-40° E shear zones. The N000° shears are interpreted as refracted or deflected equivalents of the N030° shears. The combined shears compose the Eldrich shear system which trends approximately N030°/40° ESE and has had a general reverse movement with a minor sinistral component.Gold mineralization occurs in all four major rock types as en échelon sigmoidal shaped lenses associated with the major N030° deformation system. The distribution of ore lenses can be divided into two categories: The first category occupies sub-horizontal diorite zones. The lenses trend N-S, dip 100 40° E, and are associated with shear zones, sub-horizontal fractures or tonalite-diorite contact planes. The second category of lenses is found in felsic granitic rocks; the lenses trend either N0300!40°ESE or N060°/50°-60° SSE. Local hydraulic breccia zones are observed near ore zones occupying felsic granitic rocks. These breccias may have resulted from high fluid pressures brought upon by confinement as a result of impermeable zones in an anisotropic tonalite-diorite system."

Jan 1, 1990

By W. S. Szolga, M. Moser, M. D. Soderstrom, L. Cohen

"CYANEX® 272 is a phosphinic acid-based solvent extraction reagent used commercially since the early 80’s to recover and purify cobalt from sulfate solutions. Historically, the design of CYANEX 272 circuits has involved the selection of an optimal pH profile during pilot-scale testing using mixbox pH control. The desired pH profile is required to be carefully controlled in the same manner during commercial operation. To assist operators in the design and optimization of their circuits, Solvay developed CYANEX 272-specific solvent extraction modeling software, which has enabled determination of the ideal pH profile and staging configuration. Solvay’s recent advances in modeling capabilities have allowed the simulation of circuits without direct mixbox pH control. Modeling has indicated that circuits operated without direct pH control can achieve the desired metal separation while simplifying the commercial operation significantly. This paper reviews a number of potential circuit configurations for the use of CYANEX 272 and demonstrates the separations achievable under the right design and operational conditions, some of which have historically been considered too difficult.INTRODUCTION CYANEX® 272 is a phosphinic-acid based reagent designed specifically for the separation of cobalt from nickel by solvent extraction from weakly acidic sulfate solutions (Rickelton, Robertson, & Burley, 1982; Rickelton, Flett, & West, 1984; Rickelton & Nucciarone, 1997). Following commercial introduction in the 1980’s, CYANEX 272 has been used in a number of hydrometallurgical flowsheets for cobalt purification and/or recovery. CYANEX 272 metal extraction occurs by means of a cation exchange mechanism. Extraction of a divalent metal ion M2+ is represented by the following equation where RH represents the CYANEX 272 ligand and MR2 represents the ligand-metal complex."

Jan 1, 2017

By E. Bonsall, J. J. Brummer, A. R. Graham

"A method and device are described for sampling diamond-drill core by cutting a continuous fillet of constant cross section from the cylindrical surface of the core throughout appropriate sample lengths. The apparatus employs a tapered, abrasive-set, cutting wheel, the conical cutting surface of which projects slightly into a rectangular core-guiding trough set parallel to the axis of rotation. The depth of fillet and thus the amount of sample per unit length can be regulated by adjusting the core guides. The freshly cut fillet itself, by engaging in a guide beyond the cutting wheel, acts to prevent rotation of the core during operation of the device.The cuttings which form the sample are normally collected in a tray below the cutting-wheel and appear at about 80 per cent -100 mesh. They require little or no further treatment or comminution before analysis. Speed, economy and convenience of sampling are thus greatly increased as compared with conventional sampling by im-1>act breaking or sawing, followed by crushing, grinding and sub division for assayAssays from fillets (about 1/20 the cross-sectional area of the core) and from 180-degree segments, from the same ninety-three core-samples, representing 431 feet of nickel-copper mineralization, gave the following results:"

Jan 1, 1968

By D. R. Derry

This paper up-dates an earlier paper by the author on the rate of new Canadian mineral discoveries and the exploration methods which were principally responsible for these finds. He concludes that the ratio of exploration expenditure to production value must be increased if we are to provide sufficient new reserves for the future.

Jan 1, 1970

By A F. Kravic

Carbonyl nickel powders of irregular particle shape and low a11parent density are used extensively in the production of porous nickel electrodes for nickel-cadmium storage batteries and hydrogen-oxygen fuel cells employing alkaline electrolytes. Such porous nickel matrices are at-tractive for these intended applications as they are relatively inexpensive, are corrosion resistant, have good electrical conductivity, can be welded to form electrical contacts, have a long life (as demonstrated in alkaline storage batteries), and are rugged and vibration and shock resistant. This paper describes a feasibility study concerning the production of porous multi-layer nickel electrodes by the pressing and sintering of stacked layers of green-powder rolled nickel sheet. Background H AUSNER (1) conveniently listed nine different powder compaction processes used for forming metal powders into useful shapes. These are shown in Table I. There are additional powder metallurgy processes; however, most of these are combinations of two or more processes listed in the Table. A study of the literature revealed that every powder compacting process, with the exception of isostatic pressing and explosive forming, has been evaluated or is being used for the manufacture of porous metal electrodes.

Jan 1, 1965

By A. G. Scobie

A spectrographic method for the determination of small amounts of gold and the platinum metals in ores has been developed. By means of this method, an assay of 0.001 ounce per ton on one assay ton samples is possible, and by seecrrographic adjustments the sensitivity may be increased to 0.0001 ounce per ton. All the prec10us metals may be determined from one spectrographic arcing with an accuracy of about 5 per cent average deviation from absolute values, and the complete analysis of an ore or similar product may be reported five or six hours after receipt of sample.

Jan 1, 1945

By John H. McKillop

Industrial minerals production in Newfoundland in--creased in gross value by a total of 175 per cent during the ten-year period from 1954 to 1964. The Province accounts for all of ?Canada's fluorspar production and contains one of the most important fluorspar districts in North America. It is also the only producer of pyrophyllite in Canada, and quite recently has become an important producer of asbestos fibre. Limestone, gypsum, brick shale, sand and gravel also ?Contribute appreciably to the expanding industrial minerals phase of the Province's rapidly growing mining industry. Geological diversity characterizes Newfoundland's industrial minerals: Pyrophyllite deposits were formed by contact metamorphism of predominantly volcanic Proterozoic rocks. Fluorspar deposits are fissure-filling veins having the characteristics of typical epithermal deposits. Chrysotile asbestos production comes from one of the Island's serpentinized ultrabasic belts. Limestone is produced at three localities; two of them in the extensive carbonate rocks of the west coast. Gypsum production comes from a thick evaporite (gypsum and anhydrite) sequence in the Carboniferous rocks of the St. George's Bay area. Introduction

Jan 1, 1965

By H. -L. Heikkilä, E. Peuraniemi

"Boliden Harjavalta Oy has a long tradition in the Finnish metal industry starting from the 1930's. The Smelter consists of copper and nickel flash smelting lines. Off-gases are captured in the acid plant to produce sulfur products. During the early years of production, the surrounding environment suffered from high SO2 and dust emissions. The first acid plant started in 1947, a few years after commissioning of the smelter. The flash smelting method was developed and commissioned in 1949. This created the basis for today’s environmentally sound metal production. Recent air emission reductions are related to treating lean ventilation and granulation gases. Emissions from the stacks are monitored with continuous measurement devices. SO2 and PM10 concentrations are also measured from the residential area and reported online in cooperation with Harjavalta community and other local industry.INTRODUCTIONProductionBoliden Harjavalta Oy smelts copper and nickel concentrates and refines copper in the western part of Finland. The copper concentrates come from external copper mines mainly in South America and Europe. Concentrates are unloaded at the Pori harbor and transported to Harjavalta by train from a distance of about 60 km. Boliden Harjavalta Oy has operations in Harjavalta and Pori. The smelter in Harjavalta produces copper anodes that are transported via railway to the copper refinery in Pori. The anodes are electro-refined into copper cathodes and by-products like Se, Ag, Au and Pt/Pd concentrate. In the Harjavalta smelter SO2 containing gases are delivered to a sulphuric acid plant where sulphuric acid and liquid sulphur dioxide are produced.Our nickel smelter smelts nickel concentrates on a tolling basis to produce nickel matte for customer needs. SO2 containing off-gases are delivered to the sulphuric acid plant for sulphur capture and modification into products.All our operations are certified according to the Quality, Environmental and Occupational Health and Safety Standards ISO 9001, ISO 14001 and OHSAS 18001. Boliden Harjavalta Oy was the first company in Finland operating in the metal and technology industry to be certified according to the Energy Management Standard EN 16001, currently this certification is done according to ISO 50001."

Jan 1, 2012

By N. J. Shackleton, N. A. Chapman, V. Malysiak, C. T. O’Connor

In this study, the effect of using conventional crushing and high-pressure grinding rolls (HPGR) in combination with dry or wet milling was investigated using a base-metal sulphide (BMS) sphalerite and a platinum group mineral (PGM) ore to determine how these processes affect the flotation performance. In sphalerite, irrespective of the crushing procedure (HPGR or conventional), dry milling resulted in the highest grades and recoveries of zinc, whereas in PGMs, similar treatment produced the poorest results. The results were investigated further by the effect of factors such as percentage liberation and particle size on the flotation results.

Jan 1, 2012

Energy benchmarking is widely applied across industries to determine the potential to improve energy performance. Unlike the many technologies for which energy benchmarks and efficiency rating systems are already in maturity, benchmarking of mining processes is still in its infancy. Benchmarking energy usage in mining operations, where energy costs are high and represent a significant portion of overall operating expenses, is challenging due to the uniqueness of each mining operation. Mines vary in terms of geology, geographic setting, ore body geometry, mineralogy which impact the mining method, material handling, processing and waste management. In order to gauge the opportunity for reducing the energy intensity of individual operations and also to compare the energy performance of operations on a global scale, the deployment of new benchmarking methodologies, models and frameworks is necessary. As a step towards the establishment of an accurate framework for benchmarking the energy consumption of mining operations, comminution, one of the more energy intensive mining sub-processes, was selected as the focus of a new energy benchmarking method. The methodologies and processes used to onset fragmentation in a rock mass to the crushing or grinding of rock to a size that is suitable for economic extraction are predominantly dependent on the ore properties. For this reason, site specific factors, such as the size reduction requirements and ore hardness were included in an energy benchmark model so that the energy performance of comminution processes at different operations could be normalized and compared on a global scale. Single particle compression breakage has been identified by several prominent researchers in the field of comminution as the upper limit of energy utilization in size reduction processes. For this reason single particle compression breakage was proposed as the basis of a work index for ores to be used as an input for the benchmark model. Overall, the new method showed that the energy benchmark for mineral comminution can be normalized and subsequently compared for a range of mining operations once the ore hardness has been appropriately characterized.

Aug 1, 2013

By J. Drenda

The model for methane removal from the workings directly behind an advancing longwall as presented in this paper may be used for U-ventilated cross or length-wise systems of longwall advance, starting from the boundaries of the extraction field. In mines with high methane concentrations, Uventilated longwall extraction from the boundary of the extraction field produces a methane risk. The risk is manifested by a higher methane concentration at the end of the longwall, upper gate and incline. The methane in increasing concentrations, which is emitted mainly from the workings with caved areas, appears towards the end of the longwall and in the upper gate. The graphical model of the longwall provided includes both the workspace of the longwall and the caved area. Based upon a model of the rock distribution in the cave, a ventilation model comprising two standard air splits and large number of crosswise air splits has been constructed. Simulations indicate that if the shearer is not present in the longwall, the air distribution in the caved area is symmetrical. The presence of the shearer, both at the bottom and the top of the longwall, causes an asymmetrical air distribution in the cave, that is the asymmetrical flows in the goaf and longwall workspace and in the inflows and outflow between those regions. This phenomenon causes an increase in methane concentration at the end of the wall and at the upper gate. The methane removal method proposed for workings with a caved area directly behind the advancing U-ventilated longwall, starting from the boundary of the field, consists of the removal of methane-air mixtures from the caved area with the boom pipes. These booms may be of several meters long and may be extended if necessary. The insertion of the boom pipes into the cave towards the end of the longwall and connecting them with the general methane removal system creates negative pressure causing a change in the depression field, which is the aerodynamic potential field in the goaf area around the ends of the boom pipes. This will promote the extraction of the methane-air mixture from voids and the goaf cracks, and the area from which methane is being extracted may extend to the side of the cave. This is a positive phenomenon, which could result in the methane flow from the goaf into the airflow in the longwall workspace decreasing or even stopping. A reduction in the methane flow into the longwall workspace with extractions booms will be advantageous for the production continuity. Based on the floor load model for the rocks in the cave and the methane-removal boom load model, the value of the force required to move the boom behind the advancing wall has been calculated. Strength calculations for the pipe were performed using a finite elements method. The analysis results, as well as the comparison of the pipe material effort to the strength parameters of steel, which can serve as piping material (for the assumed load conditions), lead to a belief that the proposed boom construction satisfies the strength requirements.

Aug 1, 2013

By Kazuhide Nakaniwa

In this research, we devised a measurement method using total stations (TSs) which have ?the Baum? which is a concentric circle reticle, as substitute for crosshairs. The Baum owes its name to the similarity between the concentric circles and trees (Baum in German). By setting one circle on both of edges of cylinders, operators can set their sights on points on the center line of the cylinders, and also can measure positional coordinates of the points. Also, by measuring two different points on the center line, operators can measure the position and tilt of the axes of the cylinders. Furthermore, we developed a pile driving navigation system. Foundation piles are used for various structures, and their forms are generally cylindrical. Especially, although it is difficult to drive tilted pile foundations, their usage are expected to expand due to their high earthquake resistance. Yet, a method to accurately measure the tilts of piles has not been established. However, we proved that operators can obtain adequate accuracy to control foundation piles through the measurement experiment using this system. Using this system, the information of the pile is measured using a TS, transferred to a PDA, and displayed from the operator?s view of the piling machine.

Aug 1, 2013