Search Documents

By M. Fan, H. E. Wyslouzil, J. Kohmeunch

Eriez HydroFloat(TM) separators and Canadian Process Technologies (CPT) flotation columns have been developed to overcome the limitations of traditional flotation cells in recovering coarse and fine particles, respectively. The flotation column can effectively separate 30-5 µm phosphate. Several industrial-scale HydroFloat separators have been installed in phosphate and potash beneficiation plants. Industrial-scale ultra-coarse (+850 µm) phosphate separation results suggest that a more-than 40% BonePhosphate- of-Lime (BPL) recovery increase and a 37% collector consumption reduction can be achieved. The paper describes the applications of Eriez HydroFloat separators to coarse particle separation and the CPT flotation column to fine/ultrafine particle flotation.

Jan 1, 2009

By L. Frost

"Since the late 1990s, increased prevalence of severe lung disease among US coal miners has been observed, particularly in central Appalachia where thin-seam mining is prevalent. While respirable silica exposures have been implicated in many cases, the available dust monitoring data from mines shows no explanatory trends. One possible factor could be differences in the relative toxicity of silica particles based on their surface condition. Previous research has indicated that particles with occluded surfaces (e.g., by a thin layer of clay) may be less toxic than those with non-occluded surfaces. However, this dust characteristic has not been investigated before now in central Appalachian mines. In the present study, 18 respirable dust samples from seven central Appalachian mines and two northern Appalachian mines were analyzed to assess the relative occurrence of surface-occluded silica. Results showed that the dust from central Appalachian mines actually had higher fractions of occluded silica, which may be due to extraction of large amounts of rock strata along with the coal. However, the central Appalachian mines also more silica particles overall (i.e., occluded + non-occluded) in terms of total number percentage of respirable particles.INTRODUCTIONResurgence of occupational lung disease among US coal miners, especially in the central Appalachian region, has been observed since the late 1990’s (Gibson, 2016; Zosky et al., 2016; Suarthana et al., 2011; Gamble et al., 2011; Antao et al., 2005; Attfield & Sexias, 1995). In addition to increased prevalence of simple Coal Workers’ Pneumoconiosis (CWP, or “black lung”), the prevalence of severe and rapidly progressive disease has risen dramatically (Almberg et al., 2018; Blackley et al., 2018a, 2018b, 2016, 2014; Graber et al., 2017; Cohen et al., 2016). While exposures to respirable silica have long been known to cause or play a role in diseases such as silicosis or progressive massive fibrosis (PMF), which is conventionally considered as the most advanced form of CWP, it is unclear whether silica is the only culprit in the recent outbreak of severe disease. Indeed, as disease rates have risen, both total respirable dust and silica concentrations generally appear to have declined since the late 1980s, based on regulatory monitoring data in the most affected mining districts (i.e., MSHA coal Districts 4, 5 and 12, which cover central WV, eastern KY and southwestern VA, and southern WV, respectively) (Figure 1). Of course, the latency of disease can vary and may be or more 10 years, but many of the most recent cases are likely to have resulted from exposures that occurred since the late 1980s."

Jan 1, 2019

By G. R. Heffernan

"In the early 1970ssteelmakers worldwide were looking forward to many years of expansion and profitability. Huge government investments in Europe, the United Kingdom, Japan, Brazil, and Venezuela were committed in anticipation of growing market s based on long-term OECD forecasts. In 1973 the first OPEC oil shock occurred. Steel demand shrank. Restructuring became the buzz word of the day as billions of dollars in taxpayers' money was poured into eliminating excess capacity and labour. In the United States, where government help was not available, inefficient companies went bankrupt; capacity was cut to 100 million tons from 155 million tons. The industry throughout the industrialized world shrank. By 1979the world economy seemed back on track and a modest degree of optimism could be detected in the international steel fraternity. Then came the second oil shock. By 1982 the industry was in the midst of another shakeout. More bankruptcies, more rationalization, and fewer jobs resulted. In Canada some well-known companies came close to the brink as low prices and high interest rates took their toll. In the light of the turmoil in the steel market over the past 20 years an attempt to forecast the trends through to 2001 is intimidating.However, there are good reasons to be optimistic today about both markets and technology.An economic super power is emerging in western Europe as 1992 draws near. The creation of a single market of 320 million well educated and economically ambitious people has major positive implications for steel demand. The mega projects of the channel tunnel, a European network of high speed railways, and the London docklands are the forerunners of greater things. Still to come is another $200 to $300 billion by the year 2001 in identifiable major projects for highways, railways, airports, water and sewage systems. Add to that the demands of an increasingly affluent population for automobiles, appliances and housing. On top of all that place large increasing demands for electric power and you have a potential beyond anything seen during the 1970s and 1980s. In 1988 the EEC steel industry operated at 90% and in 1989 at 92% of effective capacity. A surge in spot prices indicated that 92% was close to the ceiling. This pace moderated in early 1990 but any slack will probably be taken up rather quickly."

Jan 1, 1990

By MAX VOS

Lithium is the lightest and electrochemically most reactive of all metals. Renewed interest in lithium coincides with research in lithium batteries and power generation by atomic fusion. Ontario lithium resources are contained in spodumene pegmatites that can form where medium- to high-grade metamorphic volcanic-sedimentary formations are intruded by pegmatite and porphyritic granitic rocks. Spodumene pegmatites occur in at least twelve locales throughout northern Ontario, all of which are in the Superior Province of the Precambrian Shield. Tantalum, cesium, rubidium, beryllium, niobium and tin also were noted with lithium in spodumene pegmatites. Considerable potential remains for discovery of additional lithium and rare-element pegmatites in northern Ontario.

Jan 1, 1984

By Jorge Lema Patino

"The purpose of this paper is to determine the best techno-economic alternative for the treatment of tin ores, when comparing the various mining and metallurgical methods of preconcentration, concentration, volatilization (fuming) and up to the final stage of selling to the smelter. The study of the influence of the different parameters of cost, recovery and quoted prices has motivated the paper, which aims at determining the best process of ore treatment in terms of its techno-economic feasibility.Method of WorkOn the basis of head grades of 0.5, 0.75 and 1.0% tin, the following alternative methods of treatment are possible:1. Mining-Concentration-Smelting.2. Mining-Preconcentration-Fuming-Smelting.3. Mining-Concentration-Separation, with direct smelting and fuming/smelting of the two fractions produced.The calculations were carried out on the basis of existing information and publications concerning the various experimental recoveries in the operating mills of COMIBOL. In the case of concentrates containing less than 10% or more than 40% tin, extrapolation was required.The final grade of the tin concentrates and the gross weight of the concentrate were calculated on the basis of the estimated recovery curves. The costs of the preconcentration and the concentration stage s were determined per gross metric ton of material treated.The calculation of the cost of the smelting stage is similar for all the alternatives, the royalties and smelting charge varying with the grade of the final concentrate. In the fuming stage, a uniform recovery of 90% was taken in all cases so as to obtain a final concentrate grade of 65% tin, regardless of the head grade of the feed material.For the separation stage, the following considerations apply:a) Separation can be carried out by gravity separation or flotation methods.b) The cost of separation varies depending on the system used.c) The distribution of tin in the two fractions is 100% at this stage. In other words, there is no loss of tin during separation."

Jan 1, 1982

By A. B. Szwilski

"The various elements of longwall mine design are reviewed, particularly as they apply to condition s in the coalfields of the Plains region of Alberta. The following recommendations are made: (1) optimum panel lengths of 1000 to 2000 metres; (2) face lengths of 100 to 150 metres; (3) the use of retreat methods; (4) the restriction of floor undulations to less than 15 degrees. IntroductionThis article considers the elements of longwall mine design and is part of a short study that has been made of the feasibility of longwall mining in the Plains region, Alberta, Canada. The Plains region, with about 20 million tonnes, accounts for more than 80% of the coal resources of Alberta. The coalbearing strata in the Plains region cover an area of about 95,000 square miles. The geological formations dip very gently toward the southwest and, from a mining point of view, may be considered horizontal. The depth of the coal seams varies from several metres to over 650 metres. However, it is not anticipated that underground mining will be extended beyond the depth range of 25 to 250 metre s.The coal seams in the Plains region have been subject to many small mining operations in the past. The majority of these small mines were limited to a depth of about 50 metres, working mainly by room-and-pillar methods, although hand-filled longwall mining was often used.The development of new underground mining operations in the Plains region will have to be on a 'start-from-scratch' basis, especially regarding the installation of equipment. Longwall mining is more mechanized than any other method of mining and requires careful attention for the selection of new and expensive equipment. There have been many proven longwall advance and retreat systems in Europe and North America; mining conditions in the Plains region are more similar to those in the United States. Therefore, it will be essential for new mining pro jects in the Plains region to commence with proven system s and equipment; in time, perhaps an experimentation process could be attempted as experience is gained.Generally, the coal face is the key factor in mine productivity, which depends a great deal on equipment reliability, training and experience of the operators. The original design of coal faces must be flexible enough to cater for potential improvements so that running time can be increased."

Jan 1, 1980

By C. Mills, A. O. Burt

"The paper examines the role of gravity concentration in both an historical context and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of more mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration with other forms of processing.IntroductionIt is an unfortunate, albeit popular, misconception among otherwise enlightened engineers in the mineral processing industry that gravity concentration was a process developed in the dark ages, perfected in the middle ages, and abandoned in the modern ages.Gravity concentration was developed in the dark ages - long indeed before that. Agricolau: cited examples of gravity concentration, crude examples admittedly, being practiced over 3000 years ago. However, gravity concentration is not dead. Far from it. As recently as 1978 it was reported that the total mineral tonnage treated by this process in the United States was greater than that processed by flotation. Coal represents the bulk of the or e treated by gravity separation in the U.S.A., with iron ore representing a major portion of the balance."

Jan 1, 1985

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019

By H. M. Woodrooffe

IT IS WELL KNOWN that chrysotile asbestos from various occurrences exhibits varied physical properties and certain differences in chemical corn position, both of which conditions may have an important bearing on the industrial utilization of the fibre. The usefulness of a harsh fibre in the manufacture of asbestos cement products and of low-iron fibre for certain electrical uses are examples. It is also .possible to obtain a fibre with a texture too harsh and brittle to be of economic value. Much research into the structure of the mineral and to a lesser degree observations relating the water of combination to certain physical properties have ?been reported. This paper is an attempt to show that the pyrolysis of ?chrysotile takes place in three stages and that the conditions of pyrolysis are peculiar to the fibre and may afford some clue to the variations in physical properties of asbestos fibres which affect their utilization.

Jan 1, 1956

By W. R. Tyson

Imperfections such as lack-of-fusion and undercut are inevitable in field welding of pipelines. Above a certain size, such defects must be removed or repaired. In the present state of the art, determination of allowable defect size is done by Engineering Critical Assessment (ECA). This requires measurement of toughness, and comparison of toughness with crack driving force. ECA methods used in current international pipeline standards will be reviewed and compared.

Jan 1, 2010

By Victor F. Hollister, Robert W. Hodder

"The petrology and mineralogy of porphyry copper deposits are thoroughly described in recent literature and cited as the definitive characteristics for this type of deposit. The magmatic-hydrothermal aspect of genesis is also dealt with in detail. However, descriptions of their internal structure and regional setting are not as rigorous, and the genesis of this structure is simply stated as the release of high fluid pressures in a cooling magma emplaced along large fault zones. Genetic relationships between internal structure, regional setting and the tectonic evolution of continents has been alluded to infrequently in the past, but can now be considered together within the developing concept of orogeny at the margins of drifting crustal plates.Tensional structures, on both local and regional scale, and a Triassic to Tertiary age are described for porphyry copper deposits. We contend that such structure and age are distinct and unifying characteristics for this type of deposit and are genetically related to major crustal movements. British Columbia has porphyry copper deposits contemporaneous with plutons 180 to 200 million years old and 40 to 60 million years old. The former age group correlates with early stages of the continent's westward drift, and the latter group with a change in tectonic style during late development of the Canadian Cordillera. Hence, one can in British Columbia reflect on the genesis of a deposit's structure in the broader context of tectonic evolution. Such consideration should lead to more definitive criteria for area selection in exploration."

Jan 1, 1972

By Harry Jomini

Introduction The Wakefield plant of the Aluminum Company of Canada, Limited - a member of the Aluminum, Limited, group of companies - produces magnesia, magnesia fertilizer ingredient, and hydrated lime, from brucitic limestone. Wakefield is on the Gatineau river in Wakefield township, Quebec, some 22 miles north of Ottawa. The plant is near the western bank of the river adjacent to the Ottawa-Maniwaki highway and branch line of the Canadian Pacific railway. The plant is unique in the sense that it is the only place in Canada where brucite is processed. It is also distinguished for its outstanding safety record, as not a single lost-time accident occurred during either 1948 or 1949. The plant is amply provided with safety and comfort provisions in keeping with the standard practice in all of the twelve plants operated in Canada by Alcan and its associated companies. History Following the identification of brucite in the Rutherglen and Bryson districts in Ontario, occurrences of the mineral were discovered in the Wakefield area, Quebec, in 1939. After exploratory work on these deposits and investigation by the Bureau of Mines, Ottawa, on a method of extracting the brucite from the ore, a plant for treating the ore from the Maxwell property was built in 1941 by the Aluminum Company of Canada and commenced operations in early 1942. The process used is more or less in accordance with the method worked out by Mr. M. F. Goudge of the Bureau of Mines.

Jan 1, 1950

By H. J. Oterdoom

SMS Group (SMSG) has always been concerned about safety aspects of electric smelter plants for the ferro-alloy and non-ferrous industry. The awareness for safety increased significantly over the past decades and also SMSG contributed with its design features to a safer operation. Today, safety aspects are not only part of the smelter design but also of the overall plant layout. Explosions in electric smelters are rare, but have a huge impact on peoples’ lives, on equipment and on production. For this reason, SMSG wanted to have a better overview of explosions within the smelting industry in order to see if useful statistics could be extracted. Generally, there is a lack of statistics regarding explosions in the electric smelting industry, and not enough information is collected or published. A significant portion of the explosions seems to be water related. Many companies, both operating and engineering, are trying to handle the risks of water, and apply methods to detect water leakages. Installing such a system is a management decision and management has then to make sure the system is properly implemented. The disadvantages and limitations of these systems should be carefully considered and communicated to operators and authorities.

Jan 1, 2015

At the end of a century of mining education in South Africa, it is appropriate to reflect on the past, take stock of the present and ponder the future of mining education. While it is likely that changes in the mining industry will generate an increased demand for mining graduates, the number of suitably qualified applicants to study mining is worryingly small. While good progress has been made in unifying the educational system that previously provided schooling on a racially separate basis, it appears that a decade or more will be required to raise competency levels in mathematics, science and English, and this paper describes the process as it affects mining engineering programs. It also describes the initiatives currently being undertaken by the University of the Witwatersrand and the mining industry to ensure that the South African industry receives an adequate flow of well-qualified mining graduates, despite more than 70% of the intake coming from severely disadvantaged educational backgrounds.

Jan 1, 1999

By J. S. Fox

It is generally recognized that the interpretation of bedrock geochemical data in volcanic terrains can be improved by adjusting for rock-type. Various chemical attributes of volcanic rocks have been put forward in the literature as rapid indicators of rock-type, but there is some question as to which of these is the most reliable . Only one such attribute, total iron, seems to have seen systematic use in geochemical mapping in the Flin Flon region. Discriminant analysis of 500 basalts, andesites, dacites and rhyolites suggests that SiO2 is the most important rock-discriminating variable and that MgO, CaO, TiD2, AI2O3 and FeOtot, are successively poorer discriminators. Lithological normalization in the subalkaline volcanic environment should therefore be made over ranges of this variable. Trace-metal data from drill core through the sulphide orebody at Hanson Lake, Saskatchewan are used to demonstrate various approaches to lithological correction, including silica normalization, factor analysis and trend analysis. All of these extract economically important information from the core that is not apparent in the raw data logs. However, silica normalization does not seem to be subject to as many serious limitations as factor and trend analysis in this case, and therefore seems to provide the most reliable basis for the interpretation of subsurface exploration geochemical data.

Jan 1, 1978

By Kenneth G. Thomas

Since approximately 2003 we have witnessed the unprecedented escalation in commodity prices. Coupled with economic chaos following the 2008 economic downturn this has caused difficulties in controlling schedule, capital costs and operating costs for mining projects. Once again escalation has returned to commodity prices fuelled by growth in the BRIC countries especially China and Brazil. This is further exasperated by the missing generation of skilled technical personnel not graduating from universities in the 1980s and 1990s owing to depressed commodity prices. This paper examines the six tenets for successful project implementation.

Jan 1, 2011

"Batch flotation testwork demonstrated that a low-grade chromite ore from Bird River, Manitoba, was best floated at pH 2 using Armac C (coco amine acetate) collector and sulphuric acid as pH modifier. A grind of 100% minus 150 um was necessary for liberation, and flotation selectivity was greatly enhanced by prior desliming. A concentrate analyzing 24.2% Cr203 with a recovery of 90.2% was obtained, after three cleaning stages, from ore grading 6.05% Cr203. Total rougher collector concentration was 500 g/t and cleaner collector concentration 380 g/t. Similar grade and recovery were obtained during the pitot-plant evalualion, when a concentrate analy zing 22.3% Cr203 with a recovery of 93% (based on deslimed feed) was obtained for a total collector addition of 630 g/t.Selective flotation in a region of positive surf ace charge implies anionic activation, and a possible flotation mechanism is suggested.IntroductionIn an earlier study(1) of the beneficiation of chromite ore from Bird River, Manitoba, several methods of beneficiation were explored. These included ore sorting, heavy-media separation, and gravity concentration with flotation using Armac C (coco amine acetate) collector at pH 2, and sulphuric acid as pH modifier. Because flotation was not fully evaluated, a laboratory study was undertaken to determine the optimum parameters of chromite flotation. Optimization of parameters was established first on a laboratory scale followed by confirmation a t the pilot -plant level. Flotation of chromite using Armac C and sulphuric acid as a pH modifier has been reported as being selective for low-grade chromite ores(2)."

Jan 1, 1990

By A. A. Iranzadeh

The performance of a tunnel boring machine (TBM) depends on the efficiency of the cutters, which can be influenced by geological conditions and rock mass properties. In this study, a three-dimensional numerical model, based on a discrete element method, was used to evaluate the effects of joint orientation and its spacing on the fragmentation process by a TBM cutter. Several models were constructed to study the effects of variable orientation; these models incorporated different spacing, variable spacing, different orientations on the fragmentation process, and different sections of the block model. Three parameters, consisting of induced tensile stress, induced shear stress and maximum displacement, were calculated. The stress in each section that forms chips was considered as critical stress; critical joint spacing and orientation in each section were determined. Results show that the critical orientation was in the range of 45 to 60º, where there was a possibility to achieve the maximum penetration rate. The critical joint spacing was 200 mm and, by increasing joint spacing, the value of critical stress decreased significantly. Furthermore, joint orientation could influence more than joint spacing in the rock cutting process.

Jan 1, 2009

By G. M. Brownell

Introduction The Flin Flon mine is located on the boundary line between the provinces of Manitoba and Saskatchewan at a point about four hundred miles northwest of Winnipeg. A branch of the Canadian National railway provides the town of Flin Flon with direct transportation facilities. The property was staked in 1914 and, after a considerable amount of exploration; the Hudson Bay Mining & Smelting Company was organized and brought the property into production in November, 1930 (1). Mining is carried on by open pit and underground methods at the rate of about 4,400 tons per day. Production for the year 1934 was: 99,334 ounces of gold; 1,335,319 ounces of silver; 37,486,054~pounds of copper; and 49,427,280 pounds of zinc; in addition to small amounts of cadmium and selenium. The Flin Flon deposit is one of the largest low-grade ore deposits in Canada with complete hydro-electric and metallurgical plants for the production of blister copper and electrolytic zinc. Previous Work The development of the Flin Flon mine into one of the major mining operations in Canada has created a need for a more detailed geological study of the area. Practically all of the information published to date concerns the general surface features. It is the purpose of this paper to deal more specifically with the ore-body and its relationship to the enclosing rock as revealed by studies made possible through recent underground development. The earliest published report on the area is by E. L. Bruce (2), who made a reconnaissance geological investigation of the region for the Geo-logical Survey of Canada in 1914 and established the main. petrological units. Several years later the area immediately around Flm Flon was mapped in greater detail by F. J. Alcock (3). In the summer of 1934, the area of Missi sediments to the north and east of the mine was studied by J. W. Ambrose. His report has not yet appeared in print but his findings are of importance.

Jan 1, 1935

By Tao Cheng

Previous research and applications in construction resource optimization have focused on tracking the location of material and equipment. There is a lack of studies on automated monitoring of the interaction between workers and equipment for safety purposes. This paper presents a new approach for measuring the safety performance of construction personnel particularly when they work in very close proximity to moving equipment as well as static hazards such as chemical and flammable substances. A method of generating hazardous zones according to the geometric and kinematic characteristics of the considered hazard is introduced. The spatio-temporal relationships between the hazardous zones and workers? positioning data collected by real-time location sensing technology are automatically analyzed. This approach has been validated in a controlled test bed environment that simulates a construction site. Results indicate that worker?s safety performance of selected activities can be automatically and reliably measured using the developed approach. Furthermore, a heat map is generated for visualizing proximity related issues in the test bed using the computed results.

Aug 1, 2013