Search Documents

By C. Sideco

"Concentrate drying at the Sullivan Concentrator goes back to 1937 when the original coal-fired dryer was put into operation. This was a second hand 8' dia. x 56' long Struthers-Wells rotary dryer that came from the phosphate plant in Warfield, B.C.In 1962, replacement of the old dryer was seriously considered. The shell and the auxiliary drive mechanism were badly worn and needed replacing. In April 1963, the new 8' dia. x 65' long fuel oil-fired Struthers-Wells dryer went in operation at an installed cost of $174,000.In 1965, it was apparent that a major rebuilding of the dust collecting system would have to be done. A study was carried out and a Ducon Dynamic Gas Scrubber was installed. The system went in operation in November 1966 and has fully met expectations.In the same year, the zinc dryer was converted from fuel oil to natural gas. The conversion has resulted in savings in fuel cost of 12 to 15%.Frame No. 1Zinc Dryer PerformanceDryer Make - Struthers-WellsDryer Size 3/4 8' dia. x 65' long Drum Drive - 100 HPSpeed of Rotation - 5 RPMFeed Rate - 50-65 TPHFeed Moisture - 10-12%Discharge Moisture - 4-6%Dryer Inlet Temperature - 1600-1800°F Dryer Outlet Temperature - 200-250°F Stack Gas Volume - 25,000-40,000 CFNDust Collecting Efficiency - 99.75-99.98% Duet Loss in Stack - 50-300 lbs./day"

Jan 1, 1972

By A. J. Monhemius

"This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a “hydrometallurgical copper smelter” will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.RÉSUMÉ Cet article passe en revue l’histoire des procédés modernes de contrôle du fer en hydrométallurgie. Il accordera une attention particulière aux procédés développés dans l’industrie du zinc électrolytique pour l’élimination du fer dans les liqueurs lixiviantes de sulfate de zinc anhydre, ainsi qu’aux problèmes rencontrés par l’industrie en termes d’élimination sans danger des résidus ferreux générés par ces procédés. En projetant les leçons tirées du passé sur les efforts actuels, on pourra développer des procédés hydrométallurgiques pour le traitement de concentrés de sulfure de cuivre. Beaucoup prétendent que toute tentative de créer une « fonderie de cuivre hydrométallurgique » échouera à moins de développer des méthodes permettant de récupérer le fer sous une forme pouvant directement être utilisée par les industries sidérurgique ou des pigmentsINTRODUCTIONThis paper resulted from an invitation to the author from the CIM’s Historical Metallurgy Committee to give a presentation on the early developments of iron control in hydrometallurgy. This was to take the form of a plenary lecture at the 4th Symposium on Iron Control in Hydrometallurgy, which formed part of the 28th International Mineral Processing Congress, held in Quebec City in September 2016.I was naturally flattered that the invitation was to give the lecture at an IMPC, the prestigious conference series that has been held since the 1950s. That this particular IMPC was to include the 4th Symposium on Iron Control in Hydrometallurgy, a conference series held only every 10 years, made the invitation even more appealing and appropriate. This was because I had been co-chairman of the First Symposium on Iron Control, together with my erstwhile colleague, John Dutrizac, which was held 30 years ago in Toronto."

Jan 1, 2017

By K. Thuro, B. Sellmeier, M. Krautblatter

"Recent rockfall events, like the Tramin rockfall at January 21st, 2014, underline the significance of a comprehensive hazard assessment. A common way of estimating the hazard along infrastructure is the performance of run-out modelling using 3D rockfall codes like Rockyfor3D or RAMMS::Rockfall (Dorren, 2010, Bartelt et al., 2013). The potential block volumes are often roughly estimated from talus material and an overview of the source area, where the magnitude assessment is usually physically and intellectually demanding. Nevertheless especially for increased magnitudes, the volume estimation is crucial in terms of hazard analysis. Mid-Magnitude-Events exceed the load capacity of the most mitigation measures and their date of failure is hard to predict. Here we define the term Mid-Magnitude-Events as block volumes between boulder falls (10-100 m³) and block falls (100-10,000 m³) (Whalley, 1984).The current contribution provides an approach of integral process analysis for a 200 m3 carbonate block above the federal road B 305 near the city of Salzburg in the Bavarian Alps, Germany. We performed detailed analysis of the critical carbonate block exposed to planar failure. The block volume and the dimensions of the failure surface were mapped in detail, due to the unique occasion of an accessible failure surface. The discontinuity persistence was recorded to assess a minimal degree of fragmentation for a potential failure scenario. A maximum degree of fragmentation was estimated due to recording of block dimensions at the talus slope resulting from frequent rockfalls.We performed parameter studies in terms of run-out modelling using the code RAMMS::Rockfall (Bartelt et al., 2013), taking the recorded data for block fragmentation into account. In our contribution, we aim to demonstrate a comprehensive approach for hazard assessment of mid magnitude rockfalls, taking detachment processes, fragmentation and run-out analysis into account."

Jan 1, 2015

By Michael Harley, E. Guy Charlesworth

"Abstract - Bedding-parallel thrust-hosted gold veins are developed in the Sabie-Pilgrim's Rest goldfield, eastern Transvaal, South Africa. The reefs display a complex history characterized by temporally and spatially overlapping events of similar mineralization and deformation. Recognition of the episodic reactivation of these low angle (5° to 10°) thrust faults implicates high fluid pressures (equalling or exceeding lithostatic pressures). Geochemical constraints limit the amount of fluid-rock interaction and the occurrence of transgressive mineralization within the Archaean granitoid basement suggests that the high pressure fluids originated at depth beneath the Transvaal Basin.Similarities exist between gold deposits of Sabie-Pilgrim's Rest and Telfer, Western Australia as well as Passagem de Mariana, Minas Gerais, Brazil. All deposits are sub-parallel to the enclosing bedding which is shallowly inclined. Furthermore, they are also hosted by contractional deformational structures and are clearly epigenetic in origin."

Jan 1, 1994

By Bruce C. Fielder

"The concentration of uranium in orebodies discovered in the Athabasca Basin of northern Saskatchewan over the last 20 years has increased by a factor of 100. These high grade uranium orebodies are associated with high concentrations of radionuclides, complex mineralogy and an elemental makeup that includes base metals, arsenic, and molybdenum. Exploiting these high grade ores has required metallurgical advances in milling, tailings disposal and effluent treatment as well as changes in the design of uranium mills.This paper describes the most significant advances, including advances in dealing with the environmental issues which have become more prevalent in recent years. The milling processes of the Cluff Lake Mill, Key Lake Mill, Rabbit Lake Mill, and McClean Lake Mill are compared to illustrate both similarities and differences necessary for milling different orebodies.BackgroundUranium mining in Saskatchewan started in 1953 when the Beaverlodge Mine, owned by Eldorado Nuclear Limited (Eldorado), came into operation at Uranium City. Development in the Athabasca basin started in 1975 when the Rabbit Lake mine came into operation. This was followed by the start-up of the Cluff Lake mine in 1980 and the Key Lake mine in 1983. The McClean Lake mine is forecast to start up in the near future. The McArthur River mine recently received construction approval and the Cigar Lake Project and the Midwest Project are currently in the environmental approval process.The Beaverlodge operation ceased production in June 1982 after nearly 30 years of operation. The Rabbit Lake mill processed Rabbit Lake ore from 1975 until 1985, Collins Bay R-Zone ore from 1985 until 1993, and is currently processing ore from the Eagle Point mine (Bharadwaj, Jarvi and Lam, 1996). The Cluff Lake mill processed ore from the D- Orebody from 1980 until 1984. Since then the Claude orebody has been processed and the OP and DS orebodies are presently being milled (SRK. Senes and Melis, 1987; and Cogema Resources Inc. 1994 ). The Key Lake mill processed ore from the Gaertner ore body from 1983 until 1989 and Deilmann ore has been processed since (Cameco Corporation, 1992b and I 994a). Processing of McArthur River ore in the Key Lake mill is scheduled for 1999. The McClean Lake mill will be processing ore from the JLR, Sue and McClcan orebodies associated with the McClean Lake mine. In future ore from the Cigar Lake and Midwest projects will be processed in the McClean Lake mill. (Minatco Limited. 1991a)."

Jan 1, 1998

By H. H. Bleakney

THIS paper presents evidence that in 3 1/2% nickel steel, the published temperature for the Ac1 transformation, l,275°F., represents the completion of that transformation, and that its inception occurs approximately 275°F. lower, at about l,000°F. The formation of austenite within this range, especially at the higher temperatures, and its subsequent decomposition to martensite, results in considerable impairment of the properties of the steel. That the solid solution found to occur below l,275°F. is austenite has been questioned, but the evidence herewith presented, while not decisive, appears to be reasonably convincing. INTRODUCTION The February, 1939, issue of Metals Technology contains a very interesting paper by I. N. Zavarine, Associate Professor of Metallurgical Engineering at the Massachusetts Institute of Technology. In that paper, Professor Zavarine presented photomicrographs illustrative of the microstructures produced by heating nickel steels to a temperature slightly below the carbon change point, and holding them at that temperature for various lengths of time. His illustrations show that the structures found after such treatment do not consist merely of ferrite and carbides, but are characterized by the presence of a third phase, which he describes as a' 'sub-critical solid solution'. The occurrence of this third phase in increasing amounts is accompanied by an increase in strength and a loss of ductility and impairment of elastic ratio of the steel. Some years ago, one of the authors encountered the above-mentioned phenomenon in treating large forgings of 3.5% nickel steel. After normalizing and then drawing at l,250°F., very poor mechanical properties were obtained. Investigation of the steel disclosed no inferiority in quality. Eventually, after considerable waste of time and money, a draw temperature of l,150°F. was tried. This treatment resulted in a very great increase in elastic ratio, over 5 per cent increase in percentage elongation, and proportionate improvement in reduction of area.

Jan 1, 1941

By K. John

"THE most recent estimate of minteable coal reserves in Saskatchewan was made by the Federal Royal Commission on Coal (1944- 6). Saskatchewan was then estimated to have some 24 per cent of the Canadian reserves and two-thirds of this is located in what is called the Souris-Estevan area, which lies in the southeast corner of the Province and border's on the International boundary. It is also estimated that there are some 61/2 million thousand-tons in this area of lignite coal which grades 8,000 B.t.u. or less and has a moisture content ranging from 30 to 33 per cent. Ownership of coal rights in the Province is widely dispersed between the Crown, individuals, and corporations, and a recent survey disclosed that 40 percent of ownership was vested in the Crown and 60 per cent in private individuals and corporations. Coal rights on Crown lands may be leased at an annual rental of $ 1.00 an acre. Under such leases, a royalty of 5 cents a ton is levied on all coal mined. A royalty of 7 cents a ton is levied on coal produced from lands where mineral rights were purchased from the Federal Government prior to the transfer of jurisdiction over natural resources to the Province, in 1931. An annual mineral tax of 50 cents per acre has also been imposed by the Provincial Government on all coals within a defined producing areas."

Jan 1, 1952

By Deni Côte, Michel Dagbert, Marcel Vallée

"Greater reliability of mineral deposit and reserve estimates can be attained through better quality control of the data and information acquisition, and the estimation processes. This paper reviews the following key requirements:1. greater awareness of the significant figures of both data and estimates, and better understanding of the probabilistic aspects of the estimates, their confidence limits and margins of error;2. greater reliability of the information that supports the estimates, by more explicit and more rigorous methods and standards for data acquisition and for interpretations;3. more quantitative estimations of geological/mineral continuity, based on improved three dimensional sampling patterns and the use of geostatistics; and 4. better integration at the project engineering and mine production stages, of the mineral deposit characteristics and mining method constraints, for more efficient mineral recovery and mine quality control.RÉSUMÉUne plus grande fiabilité des estimations des gisements et des réserves minières requiert plus d'emphase sur le contrôle de la qualité de I ‘acquisition de l'information et du processus d'estimation. Les exigences suivantes sont revues:1. le respect du niveau d'exactitude des données et des estimes en n'utilisant que le nombre approprie de chiffres significatifs des observations et mesures, et en exprimant le niveau de confiance et la marge d'erreur des estimations;2. l'amélioration de fa fiabilité des données par des normes plus rigoureuses pour leur acquisition et leur vérification, et par des méthodes plus systématiques d'interprétation et de modélisation;3. l'estimation plus rigoureuse de la continuité des minéralisations dans les trois dimensions des gisements, par des patrons échantillonnages mieux adaptes awe paramètres géologiquement minéralogiques, et par l'utilisation des méthodes géostatistiques; et4. l'intégration plus poussée, particulièrement lors de la planification de l'exploitation minière, des caractéristiques des gisements avec les contraintes des méthodes d'exploitation, pour améliorer la récupération et le contrôle de la qualité en exploitation."

Jan 1, 1993

By L. T. Munn

"IT IS NOT necessary here to dwell on the fact that sulphur is currently in short supply. It may be well, however, to •point out that this •storage is not merely a temporary condition, but that, judging by trends in world consumption of sulphur, it may •be anticipated that requirements will double in the next ten years.Even with improved techniques for mining elemental sulphur in the United States and the new finds in Louisiana, there is much concern as to how these future sulphur requirements can be met. It appears necessary to .turn more and more to other sources than elemental sulphur for •additional production. The three major alternative sources were:(1) By-product sulphuric acid •from smelter gases.(2) Sulphur and sulphuric acid from iron sulphides.(3) Sulphur from hydrogen sulphide contained in natural gas. The Jumping Pound sulphur plant of the Shell Oil Company of Canada, Limited, is designed to produce sulphur by the •third of these methods.Jumping Pound is a natural gas field about 20 miles west of Calgary where Shell has a number of producing wells."

Jan 1, 1952

By L. H. McKay

Tailing Dams Three types of dam have been structed to impound tailings from the Allenby mill: 1.- By classifier unit 2.- By earth dam 3.- By direct deposition of tailings The first type, which includes two dams, was built across a shallow valley which sloped down to Similkameen river, just below the mill site. Two earth embankments, one below the other, were built across the valley. Tailings were then piped to Akins classifiers mounted on wooden wheels. The classifiers were set up at one side of the valley and gradually moved ahead on the sand embankment created by the sand discharge from these classifiers, the slime overflow going to settli.ng ponds formed by the dams. Decanting wells were built in the settling ponds by placing four six-by-six timbers vertically in the ground, two feet apart, to which two-by-six tongue-and-groove boards were nailed. The elevations of the ponds were raised, as required, by nailing additional two-by-six boards on the well and bolting on more six-by-six timbers when required. The bottoms of the wells were attached to a covered launder made of three-inch lumber laid on a one per cent grade. This launder carried the overflow through the dam. The second type of dam was built across a long, narrow valley, known as Hitchen's Flat, the upper ~n d of which was about 2½ miles north of the mill. This valley, an ideal tailings site, was 4,000 feet long and from 600 to 800 feet wide. An earth embankment with a concrete spillway through the top was built approximately 28 feet high across the lower end of this valley. Tailings were then dumped into the upper end of valley, with no further expense until the basin was filled up to the level of the flume where this entered the valley. When the upper end of the valley was filled to this point there was still room for more tailings at the lower end. Therefore, a pump was installed to elevate the tailings to build a wall around the upper end of the valley by depositing sands from a launder built up on 20 foot supports and sloping both ways from the pumping station around the upper end of the basin.

Jan 1, 1950

By Vard H. Johnson

"In contrast with the well-publicized Pittsburgh coal, and the Everglades of Florida, most coal-forming swamps of Cretaceous time in western North America occupied relatively limited areas. They formed in areas of irregular subsidence, bounded by the changing levee systems of meandering streams. Coke quality is determined by the physical and chemical behaviour of the vitrain during thermal decomposition. Vitrain is at least in part a colloidal substance, originally containing large proportions of water; its formation and survival depend on maintaining a shallow cover of stagnant water up to the time of burial. Heat from swamp fires or subaerial dyhydration could destroy it or impair its quality. Observed patterns suggest that the metamorphism is almost entirely thermal, and that there is little relation to tectonic stresses, or loading. These coals had probably achieved essentially their present rank prior to deformation. Evidence of frictional heating along the thrust planes is minimal or absent. Normally, coal beds are aquifers. Oxygen carried into the subsurface becomes available and reacts with the vitrain to destroy its natural thermoplastic properties. The tolerance of oxygen without loss of thermoplasticity is inversely related to the volatile content. Significant lateral variations of coal thickness are common and sometimes occur in short distances. In deformed areas these thickness changes are more commonly due to differential tectonic stress rather than to original thicknesses of coal. Locally, coal is known to have flowed into cavities, or fractures. These principals are discussed in relation to coal deposits of western Alberta and eastern British Columbia."

Jan 1, 1972

By S. G. Enns, E. W. Yarrow

"Situated about 200 km southeast of Juneau, Alaska, within the lower Stikine River region of northwestern British Columbia, the Galore Creek porphyry Cu-Au deposits are hosted by Upper Triassic to Lower Jurassic alkaline volcanic rocks and comagmatic syenite intrusions. Early and late breccias are also locally important host rocks for mineralization. Of the twelve identified Cu-Au deposits, the most important are the Central zone, Southwest zone and the Junction deposits with a combined resource of 284 million tonnes at 0.67 % Cu.The composition of the intrusive rocks is predominantly silica-undersaturated, alkaline, and metaluminous. Four intrusive suites are identified from field, petrographic and petrochemical data. Variation within suites or lineages can be explained by alkali feldspar fractionation. An oscillation between porphyritic and equigranular intrusions is suggested by the sequence of different intrusive lineages. The youngest intrusive phase is silica-saturated.A complex succession of intrusive and hydrothermal events is demonstrated at Galore Creek, with the most intense alteration and mineralization developing early in its history. In the Central zone, early Ca-K-silicate alteration, dominated by garnet, biotite, Kfeldspar, and anhydrite grades outward into K-silicate alteration. Both are locally overprinted by retrograde sericite± anhydrite± carbonate (SAC) alteration. The most intense Ca-K-si/icate alteration, a magmatic-hydrothermal breccia, and an early syenite intrusion are all coincident with copper mineralization in the core region of the Central zone. However, higher grade mineralization in the zone, exceeding 1 % Cu with more than 0.5 g/ t Au, is typically associated with intense biotite-rich, K-silicate alteration primarily hosted by altered volcanic rocks. The highest gold grades, commonly exceeding 1 g/t, are associated with bornite-rich mineralization situated in the northern and southern parts of the Central zone.Mineralization in the Southwest zone occurs as disseminated chalcopyrite within a late, diatreme breccia and adjacent K-feldspar porphyry. In the other satellite deposits, disseminated chalcopyrite and bornite occur in volcanic rocks with alteration that is similar to the Central zone."

Jan 1, 1995

By J. Cayouette, C. Bolduc, P. Blatter

"The LaRonde mill was commissioned in 1988 and began treating ore from the Penna shaft in 2000. The mill has been expanded to accommodate 7,500 t/day, but ramped down to 6,000 t/day since the deep extension began. The process recovers gold, silver, and base metals. In 2008, the Goldex plant began trucking gold-pyrite concentrate to a treatment plant feeding pulp to the LaRonde mill, increasing gold output by 40,000 oz. In 2009, the high-grade Lapa ore processing facilities were annexed to the LaRonde plant, increasing gold output by 120,000 oz. This paper outlines the metallurgical considerations related to the treatment of different ore types.RÉSUMÉ Le concentrateur de la mine LaRonde a été mis en service en 1988 et a commencé à traiter le minerai du puits Penna en 2000. La capacité du concentrateur a augmenté afin de permettre le traitement de 7 500 tonnes de minerai par jour, capacité qui est retombée à 6 000 tonnes par jour (tpj) depuis le début de l’extension en profondeur de la mine. Ce procédé permet de récupérer de l’or, de l’argent et des métaux communs. En 2008, l’usine de traitement Goldex a commencé à transporter par camion du concentré de pyrite et d’or vers une usine de traitement alimentant en pulpe le concentrateur de LaRonde, augmentant ainsi la production d’or de 40 000 onces. En 2009, les installations de traitement du minerai à haute teneur de Lapa ont été annexées à l’usine de traitement de LaRonde, augmentant la production d’or de 120 000 onces. Cet article passe en revue les considérations métallurgiques liées au traitement de différents types de minerai.INTRODUCTIONThe LaRonde metallurgical plant in the Abitibi region of Quebec, Canada, evolved into a mature milling site following expansions in 2000–2003, thanks to improved processes, manpower, and water treatment capabilities that better accommodate the complex constituents of the LaRonde ore. The ore requires a sequence of grinding, copper- lead and zinc flotation, and precious metals leaching, ending with a carbon-in-pulp (CIP) gold recovery. A portion (35%) of the tailings is sent back underground as paste backfill after being treated with the SO2-air cyanide destruction process. The tailings area has a dedicated cyanide destruction and metal precipitation area through which the used water passes before returning as recycled water. A biological water treatment plant was built in 2004 to address water toxicity in the final effluent. The water toxicity was the result of the high sulfide content of the LaRonde ore (from thiocyanate or stable cyanide species buildup) and the use of 90% recirculated water in the mill. The water treatment plant uses bacteria to transform thiocyanate into nitrates and precipitate phosphorus from the water before it is discharged into the environment."

Jan 1, 2017

By Zhiqing Zhang, Changyun Chen, Qing Liu, Lin Lin, Zhihong Jia, Guangjie Huang, Lipeng Ding

The effect of interrupted quenching (IQ) treatments on natural aging and bake hardening response of Al-Mg-Si alloy was investigated by hardness measurements, tensile test, differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The results show that interrupted quenching at 100oC could effectively suppress natural aging and improve bake hardening response. The optimized interrupted quenching treatment is 100oC for 45min, which gives the alloy a relatively low T4 temper strength and higher bake hardening response. The formation of highly dense cluster(2) during the interrupted quenching could be the reason for suppressing the natural aging and accelerating the precipitation of ß? phase during the paint bake treatment. In addition, interrupted quenching at higher temperature (170oC) results in unfavorable properties in both T4 temper and paint bake treatment. The formation of large precipitates is responsible for these undesired effects.

Jan 1, 2015

By Bob Butler

Brunswick Mine has been involved in a comprehensive research program investigating site specific aspects of thiosalt management to eliminate its adverse environmental effects. Minimum annual reagent cost estimates for thiosalt treatment using hydrogen peroxide and sodium hypochlorite are $400K and $1.5 million respectively. Also, minimum costs for the use of bicarbonate to buffer the pH depression associated with thiosalt oxidation in the receiving environment is in the order of $400K annually. A design of experiment (DOE) research program identified that natural UV radiation, temperature, DO and water chemistry are key factors influencing the natural oxidation rate of thiosalts within Brunswick?s water management system. A DOE surface response model was used to describe the thiosalt oxidation kinetics, which were then used to develop a predictive oxidation model for thiosalt and pH control of the mill?s reclaim water system.

Nov 1, 2002

By Javier Linares García

At then end of this year will be 10 years of producing concentrate for Antamina. This is a summary of what occurred over the last decade to increase production and tonnage above the design tonnage of 70,000 tonnes per day, up to an average of 100,018 tonnes per day in 2010, an increase in production of 42.9%. Equipment currently in use is the originally installed equipment, signifying a meaningful increase in capacity without capital. In this paper, the different phases of improvements and the realization of their impacts in chronological order will be outlined. Figure 1 below shows the average daily tonnage processed each year (tonnage throughput each year/calendar days), as well as the percentage increase over the tonnage of design.

Jan 1, 2012

By Allan A. Este, Bruce Arthur

"Rio Algom's Stanleigh Mine and Mill Operation Was' officially started up in August 1983. In September 1982, Rio Algom contracted Estonix International Inc. from Lively, Ontario, to develop and implement two innovative programs: (1) Work Renovation Planning, and (2) Systems Performance Training. This paper deals with the development and implementation of these two concepts relative to the plants technology from start-up to present and the exceptional results achieved. This paper discusses how a small but motivated workforce resulted in the smooth transition from startup to full production. It also deals with how these concepts were applied elsewhere in the organization which permitted a successful transition and downsizing of the over-all operation.IntroductionRio Algom Limited produces uranium in Elliot Lake, Ontario. In the late 1970s Rio Algom entered a contract with Ontario Hydro to supply uranium from its Stanleigh property, which had been idle since 1960. The mine was subsequently upgraded, and a new modem mill was designed and built, commencing operation in 1983.From then until September 1990,Rio Algom had three producing mines and mills in the Elliot Lake area. Quirke mill, with a capacity of 6350 tonnes per day, operated continuously from 1968. The Panel mill with a 3000 tonnes per day capacity, operated since 1979. Stanleigh mill continues to operate under long-term contracts, although at a production rate about 25070 lower than its rated capacity of 5000 tonnes per day.Both the Quirke and Panel mills, although not entirely similar, were conventional uranium mills utilizing crushing, grinding, leaching and ion exchange. As such, and in keeping with the traditional management style, there was a rather large mill operating workforce, which utilized a line-of-progression job classification system."

Jan 1, 1993

By W. Gordon Muir

This paper deals with the exploration, development and current operations of the salt mine at Goderich, Ontario operated by the Sifto Salt Division of Domtar Chemical Limited. The rock salt is obtained from a bed 1,760 feet below the surface, 75 feet thick, extending under Lake Huron. Annual production is in excess of one million tons. Large mobile equipment is used. Details of this equipment, as well as the shaft layout, which permits the equipment to be lowered underground with a minimum of trouble are outlined. Mining, crushing and screening procedures' are rev1ewed. Reference is also made to productivity salt distribution and uses.

Jan 1, 1967

By Penny C. Stewart

Narrow vein underground stope design engineers in Australia have expressed significant interest in the requirements and methodology for developing site-specific stability charts. This is largely due to a concern that existing stope stability charts inadequately take into account factors influencing narrow vein stope stability, such as the effect of backfill abutments and the effect of in stope pillars. This paper presents conclusions from a comprehensive statistical examination of case history requirements for a site specific stability chart and critiques literature arguments for site-specific charts. A new statistical analysis technique and a large comprehensive stability database enabled the authors to quantify case history requirements and any site-specific effects the model exhibits. The analyses indicated that a reliable stable-failure boundary requires at least 150 case histories, of which a minimum of 10 percent should be unstable stope surfaces. Marginal site-specific effects were observed for the operating conditions captured within the database. The authors conclude that the apparent site-specific effects noted in previous literature are attributable to operating conditions inadequately represented in the database. Such operating conditions could induce erroneous stability predictions at any site, and are therefore not truly site-specific. Following from these conclusions, a strategy for taking into account operating conditions particularly relevant to narrow vein mining has been proposed. In particular, the development of a chart that accounts for the effect of backfill abutments on stope stability. Backfill abutment effects are particularly relevant to mechanised narrow vein mining methods such as modified Avoca. Collaboration from at least five sites is required to obtain access to relevant data and underground drives for geotechnical mapping. Preliminary estimations indicate that approximately three months fieldwork is required to meet case history requirements. CMS data in conjunction with 3-dimensional design software will be used to calculate equivalent linear overbreak/slough (ELOS). In contrast to stable, failure, major failure and caving categorical variables, ELOS is an objective and continuous stability variable and is therefore, more conducive to mathematical modelling.

Oct 1, 2001

By D. G. Minnes

Many non-metallic minerals and structural materials are produced in Ontario to serve the needs of domestic manufacturers and export markets. In 1982 production was estimated to have a value of $765 million. Approximately 81 per cent of this was represented by structural materials, nearly 12.8 per cent by salt, and the remainder was other industrial minerals. Total mineral production in Ontario in 1982 was estimated at $3 .16 billion, down nearly $1.5 billion from 1980's high of $4.58 billion.

Jan 1, 1984