Search Documents

By Bhattacharyya AK

A two-dimensional finite element modelling technique is applied to predict the subsidence movements on a sloping ground surface above a completely mined panel. The modelling is carried out for the surface both directly and using a combination of an equivalent horizontal surface and a rays projection method and the result compared. The rays projection method provides the subsidence components on a sloping surface from the corresponding ones on an assumed equivalent horizontal surface through the point of mean elevation of the relevant part of the sloping surface. This method is used next to compare the subsidences, horizontal displacements and horizontal strains from the mining of a given panel at the surface for different inclinations. The results show that the magnitudes of the subsidence components are greater on the dip side of the slope from the point of the mean elevation, than the corresponding ones on the rise side and the asymmetry increases with the inclination of the surface. The findings are also compared with those of other research Workers.

Jan 1, 1992

By J Mauk

Water-rock reactions such as pyrite oxidation and calcite dissolution strongly influence the pH of pit lakes that develop in open-cast mines after mine closure. The Martha Mine, located in world-class epithermal Au-Ag deposit at the southern end of the Coromandel Peninsula, New Zealand, is scheduled to close in 2007, after which the pit excavation will be rehabilitated into a recreational lake; the first pit lake in New Zealand. Mineral distribution maps from XRD results of 130 andesite samples identify regions that could produce or consume acidity in the future pit lake. Maps show pyrite, calcite, adularia, albite, illite and chlorite distribution in the wall rocks. These data identify five alteration mineral associations: potassic, propylitic, weathered, oxidised and weakly-altered. Pyrite occurs in potassic, propylitic and weathered associations, whereas calcite is restricted to propylitic association in the northeast wall. Subaerial, epilimnion, and hypolimnion exposure zones describe the physical and chemical weathering processes that are likely to occur in regions of pit wall, and the potential effects on lake water chemistry. The pH of epilimnion water will depend on the relative abundance of pyrite and calcite in the propylitic association in the northeast wall, whereas hypolimnion pH will depend upon the frequency of whole-lake circulation events that distribute dissolved oxygen to deep lake layer. In mines with diverse alteration associations, mineral distribution maps are an essential precursor for accurately estimating water-rock reactions in pit lake environments. Data may be directly incorporated into a quantitative geochemical model of future pit lake water chemistry.

Jan 1, 2002

By Bourke J. H, Ashcroft T. B

Many changes have occurred in the world market for manganese over the last five years. Among these, the emergence of divided steel processes for the hot metal refining of pig iron is affecting the use of both ferruginous manganese ore and ferro manganese, at this stage particularly in the Japanese steel industry. Subsequent demand for higher quality manganese materials is promoting the use of thermally beneficiated products such as sinter. In addition, many processes are being developed for the direct smelting of fine manganese ores, of which plasma technology is the most advanced. Cost pressures and product quality requirements are encouraging pre- viously self sufficient countries such as The People's Republic of China and the USSR to import high grade manganese ores to supplement indigenous lower quality supplies. At the same time, Brazil has been provided with the impetus to convert its substantial reserves of ore to value added products.

Jan 1, 1988

By Gao K, Wu C, Xia J, Burdett M

X-ray diffraction (XRD) and transmission electron microscopy (TEM) techniques have been adopted in this study, to investigate the structure of carbonaceous materials such as graphite, brown coal char as well as coke, in order to explain their dissolution performance during ironmaking. These materials have been selected for study since they are commonly used recarburizers in the metallurgical industry. It was concluded that the crystal structure in a carbonaceous material can have a significant influence on its dissolution into iron melts. The material with the highest degree of ordering, which is graphite, showed the best dissolution performance. In contrast, the material with the lowest degree of ordering, which is brown coal char, showed the worst dissolution performance.

Jan 1, 1996

By Piga P, Sammarco O

Ventilation and the environmental climate in the Campiano mine is the subject of this re- search. The mine is located in Southern Tuscany (Central Italy), a region where geothermal gra- dients are very high (three times the average gradient of the earth). The research produced interesting indications as to the influence of surface climatic conditions on the environmental parameters inside the mine. A close correlation has been found between dry-bulb temperature and humidity ratio of the air in the mine for dif- ferent metereological conditions and for differ- ent mass flow rate values. Variations in air enthalpy, caused only by the heat exchange with the rock walls during the flowing of the air through the mine, depends on the surface temperature values. Statistical analyses have been used to ex- press air enthalpy variations on surface tempe- ratures, on the variations of the humidity ratio that the air undergoes inside the mine and on the mass flora rate. The application in practice of the results will permit the identification of correct mea- sures to be adopted so that optimal microcli- matic conditions are produced in the mine.

Jan 1, 1986

By Williams JK, Bolitho BC

Laverton Gold NL (Laverton) is the first junior Australian mining company to establish a viable mining operation in Indonesia. It successfully commissioned the Rawas plant in Sumatra this year with an average anticipated production of 85 000 ounces of gold equivalent (as gold and silver) per year, a feat of which Laverton is justifiably proud.Working in Indonesia and South-East Asia generally is very stressful for juniors and stretches human and financial resources to the limit - more so than in medium to large companies which can absorb the workload in-house more effectively.

Jan 1, 1997

By R Dunne, S Hart, G Levay

While water represents a major proportion of the mineral pulp processed in flotation circuits, relatively little research effort has been committed to understanding and controlling the influence of water quality on this process. Historically, this probably stems from the perception of water as an inert transport medium. However, the changing attitude towards water as a valuable resource, has given impetus to increasing requirements to use relatively impure make-up water supplies such as treated effluents and a high proportion of internally recycled water. In turn, this has resulted in the need for a more detailed focus on process water quality and its control to minimise adverse effects on sulfide flotation. Along these lines, prior to commissioning of a new concentrator at their Cadia Hill Gold Mine, Newcrest Mining was proactive in examining potential water sources and the influence of water quality on flotation of their copper/gold bearing ore. An extensive water quality survey of all major potential water supplies to the concentrator was undertaken. The flotation performance of the Cadia ore in each of these waters was investigated on a laboratory scale. The results of these studies identified that water quality could indeed have a significant influence on the flotation process. Since operations at the Cadia Hill concentrator began, water quality surveys of both make-up water sources and recycled flotation circuit waters have been carried out on a regular basis. By doing this, a database of water quality has been established which can be compared with plant performance. In parallel with the water quality surveys, a series of laboratory flotation tests have been conducted using a standard ore and waters from various streams to monitor changes in flotation performance as a function of water quality. These tests have indicated that certain water types may have a significant influence on plant performance. More research is required to better understand the impact of water quality on sulfide flotation. This understanding will help operators to minimise adverse effects, while maintaining the best utilisation of available water resources.

Jan 1, 2003

By Teague JK, Read HW

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years. Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the Illawarra Measures of the Southern Coalfield of New South Wales were carried out. The optimum range of vitrinite was found to lie between 45% and 60% (mineral matter free). Above and below this vitrinite range coke strength deteriorated. I Coke strength indices increased with rank and the optimum vitrinite content increased with an increase in rank. These changes will require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal. . T Use of- petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved. Significantly more work is required before coal reserves can be utilised to optimum advantage. This work would require extension of-the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1970

By S Lee, I Sohn

The ferrous and non-ferrous metallurgical industries have been utilising slags, fluxes and mattes for process optimisation and quality improvements at high temperatures. Understanding the fundamentals of the thermodynamics and kinetics of chemical metallurgy regarding slags, fluxes and mattes has been essential to the technological developments of these optimisation and improvements. This work will discuss how these fundamentals have been studied in the reactions involved and implemented in the ferrous industry from primary refining to continuous casting. In particular, the chemical driving forces that allow these reactions to take place and the limitations of the kinetics that require optimisation to enhance the reactions. In addition, the future research direction for slag technology innovation and the role of these fundamentals will also be described.

Jun 19, 2024

This paper contends that optimisation of energy resources through active control and predictive simulation modelling is possible, and that such monitoring leads to large savings in the electricity costs of hot mines (where refrigeration has to be employed). In addition, active monitoring and control can positively affect the establishment of a safe, healthy and productive working environment. In the entire optimisation process certain guidelines were set to ensure that the requirements of the Mine Health and Safety Act were met (South Africa). Varying the quantity of air supplied underground by means of variable speed drive (VSD) fans is one of the crucial factors in the interactive approach towards the optimisation of ventilation, as is refrigeration and the pumping requirements associated with refrigeration. This article highlights the interaction between the amount of air supplied and the effect it has on refrigeration requirements underground. This article also considers the effect that this would have on contaminant control. Various tools are available for ventilation and cooling design for mining. A lot of these tools are based on the assumption of steady state conditions and do not take into account instantaneous changes in conditions, day-to-day, or hour-to-hour (such as for temperature and contaminants). They also do not take into account the optimisation of energy resources related to the creation of the acceptable underground conditions. With these tools worst-case and best-case scenarios are identified, and strategic decisions are made accordingly. Currently, the amount of the fresh air, the velocity of the air, and its general temperature in the mine are only changed when one production phase changes into another (or when unacceptable conditions occur as a result of poor design or neglect). This means that during a specific production phase (which can last for several months), there can be an oversupply, or undersupply, of energy resources, which will obviously affect the concentration levels of the various contaminants (through under or oversupply of air).

Jan 1, 2005

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By Ritchie I, Fleay J

The key issues in the conceptualisation and testing of treatment options for gold and base metals mineral processing projects are discussed. A prerequisite of this process is the need for close interaction between geologists, mining engineers and metallurgists to facilitate an understanding of the orebody based on the parameters impacting on each discipline. Typical testwork programs for unit operations, including comminution, flotation and gold processing are Described.

Jan 1, 1997

Throughout the Kalgoorlie Field the dominant factors influencing all planned exploratory work are: firstly, the general geology of the district, and, secondly, the lode fracture pattern. Superimposed on these, there are innumerable faulting problems which tend to complicate the search for ore.In this paper it is proposed to deal primarily with the lode fracture pattern and to touch on the general geology only insofar as it affects ore distribution. So much has been written on Kalgoorlie geology that it would be impossible to review the literature adequately in a brief paper such as this. The basic facts of rock types and rock distribution are well established and the broad structure of the field is known in the central portion, though it is less well established towards the northern and southern ends.The latest descriptions of the general geology are those of Stillwell (1), and Gustafson (2), -and these represent the basis of current knowledge.GENERAL GEOLOGY.The field is six miles long and about one mile wide, the long axis trending north-west. The "Golden Mile," or heart of the mining 'area, covers a length of three miles in the southern section, and consists of a central core of quartz dolerite greenstone which merges into uralitic quartz 'dolerite on its western margin. The uralitic quartz dolerite is derived from an original quartz dolerite by a low grade...

Jan 1, 1948

In-pit crushing systems have been known in the mining industry for many decades. The question whether in-pit crushing is a viable option has often been asked. More than 200 mobile and semi mobile crushing systems have been installed worldwide at various locations and applications. Economic pressures have forced mine operators to reconsider the use of a conventional truck-shovel operation and have contributed enormously to the development of in-pit crushing and conveying systems. The in-pit crushing concepts have varying mobility capabilities. These range from fixed, stationary crushing plants to semi-mobile and fully mobile crushing plants. All these systems are operated in connection with a conveying system. In general in-pit crushing systems have technical and economical cost advantages over truck-shovel operation, particularly as mine capacities increase and mines become deeper. The integration of an in-pit crushing system represents a significant up-front capital investment and the mine is only able to depreciate the capital investment over a sufficient mine life including plant capacity to realise the benefit of the much lower operating cost.

Jan 1, 2003

By Veal FL

Technological changes in Portland cement manufacturing during past years have reflected changes in the economics and availability of various types of fuel such as coal, fuel oil and natural gas. The industry consumes a sig- nificant quantity of both thermal and electric- al energy. The nature of the process and its chemical constraints does however permit the use of comparatively low grade fuels such as high ash coal and high sulphur oil. In striving for increased daily kiln outputs and conservation of energy, there is a worldwide trend towards the use of dry process plants. Wet process kilns of about 2 500 tonnes per day assume massive component sizes which present difficulties in manufacture, and transport to plant sites. Large capacity dry process units in excess of 8 000 tonnes per day are now in operation using precalcination techniques in which part of the fuel is introduced in the static preheater section ahead of the kiln while the balance is added to the kiln in a conventional manner. This technique has virtually doubled the potential output of any given single kiln.

Jan 1, 1976

By R G. Barker, N Mortimer

In New Zealand, platinum group metals (PGM) occur in three main geological environments of economic interest: layered mafic igneous complexes, the Dun Mountain Ophiolite Belt, and in association with placer gold deposits. Most of the layered mafic complexes with PGM potential occur in the Median Batholith. These include the Longwood (Permian), Bluff (Permian), Riwaka (Devonian) and Rotoroa (Jurassic) igneous complexes. Exploration of the Longwood Complex discovered PGM associated with gabbroic rocks. Best assays to date include a 1 m drill intersection of 1 g/t Pt + Pd and float rock with 3.0 ppm Pt and 3.3 ppm Pd. The Greenhills complex at Bluff consists of basal dunite overlain by wehrlite and gabbro. PGM occur with chrome spinel in the basal dunite and Pt geochemical anomalies have been identified associated with the wehrlite-gabbro contact zone. The Greenhills complex has some similarities to Alaskan-Ural type complexes.Reconnaissance exploration in the Dun Mountain Ophiolite Belt has identified PGM geochemical anomalies, but no follow-up work has been carried out. During the late 1800s and early 1900s, PGM were recovered as a byproduct of placer gold mining in Southland. Placer gold prospects with PGM potential include the Waiau River, deposits flanking the Longwood Complex and some Southland beaches.

Jan 1, 2002

By Cairncross A. A

Papers on technical aspects of the Melbourne Underground Rail Loop project are being presented at this conference or have been presented previously or will be presented at other forums. This paper provides the framework for these papers by presenting the overall engineering tasks. The conceptual design, the special investigations undertaken, the management of the project and the construction development are highlighted.

Jan 1, 1981

By Simes C. D

Results of experiments for dissolution of zinc by aeration of sphalerite in glass, copper, galvanised iron and stainless steel vessels of identical dimensions are reported. It was found that in a glass container dissolution of zinc reaches a maximum after 30 min aeration and then decreases whereas in the copper container dissolution remains nearly unchanged up to 30 min aeration and then increases. In the cases of galvanised iron and stainless steel containers zinc dissolution increased steadily with time up to 60 min aeration. It is suggested that the different rates of dissolution in glass and copper containers may be due to electro-chemical actions.

Jan 1, 1984

And it takes more than good organisation. You may read or heard this poignant reflection: We tried hard, but it seemed that every time we were beginning to form up in teams we would be reorganised. I was to learn later in life that we tend to meet any new situation by re-organising, and a wonderful method this is for creating the illusion of progress while producing confusion, inefficiency, and demoralisation This was written by the Roman Gaius Petronius in AD65. How much have things changed in nearly 2,000 years? What then does it take besides the fundamentals and good organisation to build a successful career in a successful organisation? I'm prepared to venture a list of what I'll'call Tips for Young Professionals. If you've got what it takes, and apply these, I think that you'll gain a great deal of satisfaction from your career, even if you don't reach the distant target each of you should have in mind now. So settle back in an advice-receiving mode, and please forgive me if I come across as a master of the bleedin' obvious, as Basil once accused his wife Sybil of being in the unforgettable Fawlty Towers.

Jan 1, 1990

By J Tickner, Y Van Haarlem, G Roach, D Abernethy, M Smith, J OÆDwyer

The development of novel technologies capable of real-time, high-accuracy, automated analysis of gold, other precious metals and mineralogy, both in ore samples and directly on process streams is reported.X-ray fluorescence (XRF) analysis is widely used for process stream monitoring of base metals. However, detection limits are generally a few parts-per-million (ppm) or larger, precluding the use of this method for monitoring precious metals. Complex interferences with other elements also limit accuracy. An XRF slurry analyser that uses advanced data-analysis techniques to resolve overlapping fluorescence lines, achieving detection limits in the parts-per-billion (ppb) range has been developed. This allows feed, concentrate and tailings streams in precious metal applications to be monitored in real-time. An extended trial of our technology in a platinum group element concentrator and laboratory tests on gold process slurries in the 0.1 - 2.0 ppm concentration range is discussed.Analysis of process stream mineralogy can provide useful information to supplement conventional elemental data. An on-stream X-ray diffraction analysis technique that provide real-time mineral and elemental measurement of process slurry streams has been developed. Both X-ray techniques can be combined into a single on-stream analyser to provide simultaneous elemental and mineralogical information. The successful trial of a combined XRDF (X-ray diffraction and fluorescence) slurry analyser is also reported.It is widely recognised that rapid, accurate analysis of grade is an essential prerequisite for optimising the efficiency of exploration, mining and processing of metals ores. The low grades of precious metals ores, such as gold and the platinum group elements, have led to fire assay becoming the predominant analysis technique. Significant drawbacks of fire assay include long turn-around times, limited absolute accuracy, high costs and requirement for skilled operating staff. For rapid measurement of gold samples, a technique that allows the gold content of large samples to be determined absolutely with high accuracy in less than two minutes using activation with high-energy X-rays has been developed. The method is non-destructive, has detection limits in the low ppb range, is capable of measuring slurries, ground or crushed solids with minimal preparation and can be made fully automatic. Initial results from laboratory trials are presented.CITATION:Roach, G, Abernethy, D, OÆDwyer, J, Smith, M, Tickner, J and Van Haarlem, Y, 2013. Advanced instrumentation for analysis of exploration, mining and process materials, in Proceedings World Gold 2013 , pp 277-282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013