Search Documents

By P. A. Witherspoon, R. W. Donovan, T. D. Mueller

The use of petroleum-barren aquifers for underground storage has become extremely important to the natural-gas industry. A critical problem in assessing the feasibility of a specific aquifer for such use is the permeability determination of the caprock over the proposed storage project. The approach used here is to conduct both static and dynamic field tests on the aquifer being analyzed. Valuable information on the possibility of communication between the storage aquifer and any other aquifers above can be obtained by measuring hydrostatic water levels and water analyses. Significant differences in such data give evidence of the lack of communication between the intended storage reservoir and other horizons. The dynamic approach requires that one well be pumped in the storage aquifer, and changes in fluid levels recorded in both the aquifer and its caprock. The interpretation of the data from such pumping tests involves the solution of nonsteady radial flow in an infinite aquifer and the influence on such flow of a leaky caprock. A finite-difference model has been used to investigate this problem, and the transient behavior has been solved numerically with a digital computer. It has been found that the pressure transients in the storage aquifer are not affected significantly by moderate caprock leakage. The pressure behavior of the caprock is a much better indicator of the degree of leakage, and generalized solutions for this behavior are included. Field data are presented to demonstrate both the static and dynamic approach. If is concluded that appropriate investigation of the groundwater hydrology in an aquifer-type gas-storage project can provide much valuable information for determining the effectiveness of the caprock to hold gas. INTRODUCTION Underground storage of natural gas in the United States has been developing at a rapid rate over the past few years. In 1955, the total gas-storage capacity was about 1.6 trillion cu ft; by 1961, this figure was almost 3.2 trillion cu ft, an increase of 100 per cent in six years.' This trend un- doubtedly will continue because the economics favor the development of gas storage, as opposed to the construction of new pipelines, to meet the inherent cyclic demand for fuel in the metropolitan areas of this country.' About 15 per cent of the current underground gas storage has been developed in petroleum-barren aquifers, i.e., geological domes or anticlines in which no commercial quantities of oil or gas had been produced prior to the storage operations. The necessity for using barren aquifers outside many metropolitan areas of this country has been due to the lack of depleted oil or gas fields that were near enough and large enough to meet the demands of such consuming areas. Pipeline companies have developed aquifer storage along their transmission lines to meet the fluctuating needs of their complex systems. Considerable thought has also been given to the problem of storing gas in a structureless aquifer, both in this country' and in the Soviet Union outside the city of Leningrad.'," Conditions such as these have led to the development of aquifer gas-storage projects in many parts of the U. S. Most of these developments have centered in the Mid-Continent area, and the greatest amount of activity has been concentrated in Illinois.6 Thus, the use of petroleum-barren aquifers for gas-storage purposes has become extremely important to the natural-gas industry. There are three basic problems in developing aquifer-type storage: (1) finding an adequate geologic structure, (2) finding a suitable storage reservoir within the structure and (3) determining the tightness of the caprock over the intended storage zone. The first two problems can be solved by applying conventional methods of exploration geology, but once these problems are solved, the question arises as to why no oil or gas is present in an otherwise favorable setting. Two situations are possible: (1) an adequate source bed was never present, or (2) a source bed was present but the petroleum seeped away because of a leaky caprock. Determining the tightness of the caprock is one of the most critical problems in assessing the feasibility of a specific aquifer for storage purposes. In attacking this problem, one usually takes cores of the caprock and subjects them to a rigorous investigation. Such core data are desirable, but they only detail the matrix properties and cannot be expected to reveal the gross characteristics of the caprock. Several gas-storage projects in the U. S. have had considerable leakage where

By Carl S. Westerberg

1,. C. McCABE*-—An increased derliand for coal in the west is to be expected because of the growth in population and industry during the past ten years. The author calls attention to the increased mechanical cleaning of Utah coal between 1938, when no cleaning was being done, and 194.7, when more than 24 pct of the production was cleaned. This is essentially the Period of most rapid growth of the Pacific Coast. area altliough the growth and, no doubt, the general trends in coal production and cleaning continued at a less accelerated rate during 1948. The Pacific southwest increased 37 pct in population between 1940 and 191.7 while the United States showed only a 7 pct increase in the same period. it has been estimated that there will be an additional 15 pct increase in population between 1947 and 1950. The conclusion that more coal and more mechanicak cleaning capacity will be required appears to be well founded. Mr. Westerberg discusses the cco- nomic advantages of coal cleaning reflected in freight savings, in lower cost per million Btu, and lowered ash and sulphur content. In view of the limited occurrence of coking coals in the west it would be interesting to know whether significant beneficiation in coking strength can be expected from mechanical cleaning of Utah coals. This has been demonstrated for some eastern and midwestern coals. One can readily agree to the desirability of recovering the fine coal that has heretofore been lost in washery slurry. The very cheapness of coal has Iridered

Jan 1, 1950

By F. D. Rosi

IN the production of single crystals by the Bridg-man method of solidification from the melt in vacuum at a crucible lowering rate of 0.25 in. per hr, a cellular structure was frequently observed in copper and copper-base alloys at the terminal surface of the as-cast crystals (i.e., the surface representing the last portion of the crystal to solidify). The geometrical form of this structure varied from crystal to crystal, but, in general, could be classified as either hexagonal or quadrilateral. Fig. 1 shows examples of this cellular structure, which is similar to that reported by Buergerl and, more recently, by Pond and Kessler&apos; and Rutter and Chalmers. In the micrographs of Figs. lb and c, the cubic structure in the alloy crystals is obscured somewhat by excessive surface evaporation in the final stages of solidification. X-ray orientation studies indicate that the traces outlining the various geometrical forms correspond to octahedral planes, which are the planes of greatest reticular density in the face-centered cubic lattice. It would appear from this that the view first propounded by Bravais,4 that the surface energies and normal growth velocities of the different crystal planes are inversely proportional to their reticular densities, applies to this cellular structure, since those surviving are the planes of greatest atomic density. Thus, the observed variation in the geometrical form of this structure in crystals of different orientation is readily understandable from the distribution of the (111) planes in the standard {111}, (1101, and (1001 stereographic projections. Depending upon whether the crystal axis (i.e., the direction of crystallization) coincides with a <111>, <111>, or <100> direction, the cellular structure viewed from a surface perpendicular to the crystal axis will consist of a network of regular hexagons, skewed hexagons (with interfacial angles of 110" and 125"), or cubes, respectively. It follows, moreover, that off-orientations from these principal directions will yield modifications of these three basic geometric configurations. In this connection, it is interesting to note that the bounding planes of the hexagonal structure observed in tin by Rutter and Chalmers3 showed no preferred orientation.

Jan 1, 1954

By G. Vaux, M. L. Fuller

AN apparatus and procedure for the determination by X-ray reflection of preferred orientation of crystals in rolled metal with the Geiger counter X-ray spectrometer was described by Schulz.&apos; This is an excellent procedure and we have used it continually for several years. In our use of the procedure, two modifications have been made and used during most of this period. One of these provides for automatic scanning and recording of the reflections, and the other makes possible the application of the procedure to coarse-grained specimens and permits measurement of almost all orientations without resort to the transmission technique. The automatic scanning and recording are accomplished by a motor drive of the inner ring of the Schulz apparatus (see R, in Fig. 2 of his paper and R2 in Fig. 1 of this note) in synchronism with the chart recorder of the North American Philips 90" X-ray spectrometer. A rate of 10" per min is used. A scan of 180" is obtained corresponding to poles on the stereographic projection whose locus is a great circle. The modification for coarse-grained material is accomplished by allowing a larger area of the specimen to contribute to the X-ray diffraction. In the Schulz apparatus the incident X-ray beam is confined by a slit system to rays in the plane of the spectrometer. Schulz demonstrated that this restriction of the X-ray beam permits a survey of the X-ray reflections without correction up to about 80" on either side of that specimen position in which the specimen is perpendicular to the plane of the spectrometer. This is the angle + of rotation of the inner ring R2. One of these slits is horizontal and extends across the X-ray source side of the specimen. In the modification this slit is removed, thus permitting greater divergence in the X-ray beam and the irradiation of a larger area of the specimen surface. Fig. 1 shows the apparatus with the motor drive and with the slit removed. Discontinuities in the recorded X-ray intensity plot due to the few participating crystals in coarse-grained metal are much lessened. The increased divergence does not cause reflections from other crystal planes to enter the Geiger counter slit. An important advantage of the original Schulz scheme is thus lost and a system for correction is required. To do this, a compact of atomized copper powder was prepared and tested by the original Schulz method for the absence of preferred orientation. The horizontal slit was then removed and a curve recorded showing the variation of intensity with angle +. In our arrangement the intensity was uniform within the range + equals ±30°. Beyond this the intensity fell off rapidly reaching zero at ±90°. The curve thus produced is then used to correct measurements made on preferred orientation specimens. In practice this is accomplished by constructing from this calibration curve a family of curves which, as a transparency, can be superimposed on the recorder chart to read corrected intensity directly. Not only does this method permit the handling of coarse-grained material but it also makes possible the plotting of intensities almost to the circumference of the stereographic pole figure projection. Thus, nearly the entire pole figure can be plotted without the necessity of using the transmission technique. Moreover, intensities are much greater, an advantage when surveying crystal planes of poor reflecting power.

Jan 1, 1954

Francis Drake, Bulawayo, Rhodesia, So. Africa (communication to the Secretary *):—I should like to place on record some data in addition to those given by Mr. Canby in his paper. I regret that my notes have been destroyed so that I can give no accurate measurements of the water jacket that I am about to describe. This furnace mas erected in Cerro Gordo, Inyo county, Cal., early in 1875, and I think it quite possible that it was the first applied in lead smelting. It was made of plate iron and elliptic in shape, the inner dimensions being about 54 by 42 in. by 48 in. high. The distance between the inner and outer plates was about 6 in. Tuyere holes, one at the back and two on each side, about 12 in. in diameter, were made in this, and in these were placed cast-iron water tuyeres about 16 in. long, the diameter of the blast orifice at the point being about 3 in. The height from tuyeres to feed door was about 9 ft., but the top of the charge was kept about 5 ft. above the tuyeres. There was a space of about 12 in. between the jacket and the top brick-work. This brick-work was supported by a cast-iron plate resting on four cast-iron columns. At the beginning, the jacket was lined with air-dried radial bricks, made of crushed quartz and fire-clay, as it was thought that the jacket would not stand the heat on its bare plates. After a short time the practice was altered and no lining mas put in. The jacket was closed at the top and had a steam drum connected by two pipes at the back. This steam drum was connected to the boiler in which the steam was made for driving the Baker blower, the rock breaker and the pumps. The bottom of the jacket mas also connected to the boiler. The jacket was run under boiler pressure (80 Ib.) for some time, but eventually cracks developed in the inner plate between the tuyere holes,

Jan 1, 1913

By C. R. Fischrupp, M. D. Helfrick, W. A. Straw

In the manufacture of telephone apparatus a number of nonferrous sheet metals arc blanked and formed to produce a wide variety of parts, which are generally small in size because of space and weight requirements. Many are given sharp bends in forming, so that they may be assembled into compact units. This study covered sheet metal of the alloys of brass, phosphor bronze and nickel silver that are most extensively used by our company. In general, the sheets range from 0.005 to 0.100 in. in thickness and from 1/4 hard to extra spring temper in hardness. As many parts function as flat springs, and others require the maximum stiffness for structural reasons, a large percentage of the metal is used in the hard and spring tempers. So, because of the necessity for the minimum radius of bend consistent with the maximum in hardness, there has been a need for information as to the forming characteristics of these sheet metals in the various alloys, tempers and thicknesses. The literature yields relatively little regarding such forming characteristics, so that designers of apparatus and tools have been largely dependent upon past experience or tool tryouts for guidance. In presenting tabular data intended as a basis for selecting the temper of the metal and radius of the bend, we recognize the influence of many other factors which are not covered in this study. For example, the angle of the bend and conditions of the metal, such as grain size and presence of impurities, as well as conditions of the fabricating process, such as rate of forming and adjustment of the tools, may all affect the result. In addition, a bumping operation subsequent to forming, which is frequently used to set the bend, increases the strain on the metal. We wish to emphasize the fact that this is not considered a scientific investigation of the formability of materials or an attempt to correlate forming characteristics with various other properties of the metals, except in so far as such properties are controlled by commercial limits on composition and temper. It is expected, however, that the data presented may serve some useful purpose in estimating the relative formability of different thicknesses

Jan 1, 1931

By Thomas L. Kesler

Essentially all of the barite produced in Georgia has come from the Cartersville district in the northwest part of the state. The earliest recorded shipment of ore, 60 tons, was made in 1894.1 With the exception of the four-year period 1931 to 1934, the separate yearly output has been recorded and published since 1915, whereas the total yearly output of the United States has been published since 1880. The separately recorded production of Georgia (Cartersville) through 1947 is 2,232,544 short tons valued at $14,900,746,2 but unpublished data on the period 1931 to 1934, plus the estimated unrecorded output prior to 1915, make the actual total about 2,400,000 short tons. This is about 21 pct of the total production of the United States, which, through 1947, is 11,328,440 short tons valued at $71,683,386.2

Jan 1, 1949

By W. M. Small

From the one producing well in Austria, 7000 bbl. of heavy oil was produced and sold in 1933. This well, owned by the Raky-Danubia, was completed late in 1932 in the formation called Flysch (Upper Cretaceous or lower Eocene) near Zistersdorf north of Vienna. Two wildcats drilling in the vicinity have not yet reached the producing beds. Near Vienna, the European Gas and Electric Co. drilled five shallow wells for gas, three of which were failures. One gas well was completed for 8 million cu. ft. capacity at 260 meters depth and with a pressure of 570 lb. Another is being tested following blowouts. One gas well and one dry hole were completed in the pool in 1932. In Upper Austria, the same company abandoned one wildcat at 679 m. and is drilling at 280 m. on a second. No gas was sold during the year, but a line is being completed to supply fuel to boilers of the Vienna Electric Works. Hungary No deep drilling was done in 1933. Oil and gas concession was granted by Parliament to the European Gas and Electric Co. on Trans-danubia. Active geological and geophysical investigation is in progress. Czechoslovakia In the Gbely and Hodonin shallow fields, some 26 wells were drilled of which three were reported as failures. The total production of the fields was 111,736 bbl. of oil and 40 million cu. ft. of gas used as fuel in the field. At Vacenovice, where there were already two small gas wells, a third producer was completed at 420 m. This pool markets a small amount of gas, which is compressed and used to light railway carriages. Wildcat wells were reported drilling at about 300 m. depth at both Jasina and Telnice. One 700-ni. wildcat near the Hodonin field was abandoned. Another failure was reported completed and abandoned at 820 m. near Holic.

Jan 1, 1934

By Oliver Bowles

EACH year the broad diversified field of industrial minerals offers a panorama of new and interesting developments that not only concern the welfare of the industries themselves but have a more or less direct influence on the lives of citizens at large. Thus, the home life of multirudes may be affected by new building units that transmit light through walls instead of windows, by illuminated processed marble lighting fixtures and decorations, by the vast impetus given to thermal insulation Ly .mineral wool, expanded vermiculite, and related products, and, more remotely, by fireproof rugs and drap-

Jan 1, 1937

By H. C. Rogers, B. W. Roberts

Vanadium foils and wires, either cold-worked or recrystallized, show a ductile-brittle-ductile fracture sequence with temperature. At about 150°C the hydrogenated vanadium wires are found to be ductile. At room temperature the wires show brittle fracture, and at liquid nitrogen temperature the wires are again ductile, although to a lesser extent than found at 150°C. Hydrogenated cold-rolled vanadium foils have been found to fracture in unusually straight lines along the [100] texture directions. The hydrogen content required to show this [loo] texture fracture is limited to a few atomic percent in range. Hydrogen content above this range causes fracture to occur in random directions. PRELIMINARY experiments with hydrogenated vanadium foils indicated that the embrittling effect of the hydrogen on the vanadium, which was severe at room temperature, was reduced at both lower and higher temperatures. In order to investigate more quantitatively the ductility changes with temperature, vanadium wires were tested in tension at three temperatures. The reduction of area was measured and the fractures examined. Specimen Preparation—The material used was kindly supplied by A. U. Seyboltl in the form of M-in. rod. The nominal analysis was: 99.2 pct V assay, 0.2 pct C, 0.01 pct Si, 0.01 pct Fe, 0.015 pct Ca, 0.02 pct O,, 0.01 pct N2, and 0.003 pct H,. The specimens were 0.035-in. diam wires. These were prepared by cold-swaging the supplied rod to the final diameter without intermediate anneal. They were finished with long-bearing dies. The surface was then given a light polishing with 0 emery paper and degreased in trichlorethylene. An X-ray check indicated that the cold-swaged wire had a fairly strong [110] fiber texture. The wires were then recrystallized in vacuum in continuously pumped quartz tubes at two temperatures to give two different grain sizes. One group of wires was given 45 min at 800°C; another, 60 min at 1000°C. The microstructures in Fig. 1 show the wires after they have been electropolished and elec-troetched in 10 pct HCI. After the 800°C anneal, the vanadium grains had a diameter of 1 to 2p and there appeared to be a tendency to elongation in the longitudinal direction. However, the latter may be an etching effect. After the 1000°C anneal, the grains appeared to be equi-axed, but there was a very large spread in grain size, probably due to some impurity segregation in the wire, Fig. 1, right. The grain diameters varied between the limits of 1 to 150p. The small particles shown particularly clearly in Fig. 1, left, are also visible on the polished surface of all samples before etching and are undoubtedly carbides and nitrides of vanadium. An X-ray check indicated these annealed wires had a strong [110} recrystallization fiber texture. The hydrogenation was carried out in an iron retort with dry hydrogen flowing through it, the retort and contents being heated in a tube furnace with a hydrogen atmosphere. The hydrogenation temperature was approximately 500°C. The hydro-genation times chosen were approximately those which would be just enough to cause the vanadium to be brittle at room temperature and thus allow the greatest chance for ductility to occur at the other two temperatures. Part of the fine grained specimens were hydrogenated for 21/2 min at 490°C. Part of the coarse grained specimens were hydro-genated for 11/2 min at 515°C.

Jan 1, 1957

By A. L., Bailey

All who are even generally aware of the tremendous rate of increase in coal washing operations must realize the growing importance of the float-and-sink test. I believe it is conservative to estimate that, in the past decade, the dollar volume of float-and-sink testing has increased tenfold. It is a simple matter of economy, then, to examine the factors that determine the cost of adequate float-and-sink testing. When the Coal Preparation Section of the Bureau of Mines entered upon a greatly expanded program of such work in connection with the synthetic liquid fuels investigations, it seemed advisable to examine these factors experimentally. The principal consideration that differentiates float-and-sink test sampling from general purpose sampling, is that the original particle size must be preserved. Therefore, the total cost of the test will be directly affected by any standard that might be proposed to limit sample bulk reduction at any given particle size. For this reason, the relationship of sample size to variability of results was the first factor to be studied experimentally.

Jan 1, 1949

By Kenneth Cottingham

THE area described herein is situated on what is known as the Arches Fork anticline in Roane and Calhoun Counties, W. Va. When the area was first mapped, it was felt that well records would give a more intimate idea of conditions, both structural and lithologic, than could be expected from surface horizons. The surface formations are chiefly members of the Monongahela series, though northward the hilltop outcrops are those of the Dunkard. Neither series offers a key horizon sufficiently definite to be satisfactory, although the structure as determined from well records was later checked against two of the more persistent surface sandstones. In mapping the subsurface structure, the top of the Big Lime (Greenbrier) was employed as the key horizon. The average depth to the top of the Big Lime varies from 1600 to 2000 ft. (487 to 609 m.), while the average thickness as indicated by well records is 113 ft. (34 m.). The oil-producing formation is the Big Injun, lying just below the Big Lime. In two instances, well records show the Lime and Injun separated by a few feet of "break." The Big Injun is recorded as having a variable thickness. Seven logs report it as missing and one gives it the maximum thickness of 105 ft. (32 m.), while the entire average for thickness is 19 ft. (6 m.).

Jan 1, 1922

By Ralph Sweetser

THE Round Table. on Qualities of Pig Iron, under the auspices of the Joint Committee on Qualities of Pig Iron, which is made up of members of the American Institute of Mining and Metallurgical Engineers, the American Foundrymen&apos;s Association, the American Society for Testing Materials, the Gray Iron Institute, and the. Malleable Iron Institute, was held at the Palmer House, Chicago, Ill., on Oct. 1, 1935. PROCEEDINGS R. H. SWEETSER,* New York, N. Y.-Seven years ago last June we had a round table on qualities of pig iron1, and at that time the foundrymen were out with their battle-axes for the blast-furnace men, and the open-hearth men were doing the same thing. After that meeting there was really a determined effort to find out about the qualities of pig iron, and great progress has been made all along the line. This afternoon we want to have a frank discussion of the qualities of pig iron, whether it is the molten pig iron going into the steel plant, or cold pigs going to the different foundries. We ought to hear something from Dr. J. T. MacKenzie, who is chairman of the Joint Committee, and from Mr. R. E. Kennedy, the tech-nical secretary. J. T. MACKENZIE, t Birmingham, Ala.-As a result of that meeting in Chicago, there was considerable agitation in the Foundrymen&apos;s Association to develop a set of tests for pig iron. One of the difficulties was that nobody talked the same language on shrinkage, draws, live iron, dead iron, and so forth, which were the main com-plaints against pig iron. By request of a committee of the Foundrymen&apos;s Association, the Bureau of Standards ran a comprehensive set of tests that did develop the prin-ciples governing the optical pyrometer as applied to cast iron and pig iron. Then the Bureau went on further with the fluidity test, and developed a method for the absolute changes of volume at the freezing point.

Jan 1, 1936

By John S. Brock

INTRODUCTION The Oxford Dictionary says that the word "promoter" has usually been used in an opprobrious sense since at least 1876. This popular image of mining promoters is of cigar-chomping shysters and Brooklyn-Bridge vendors, improving their standard of living with the aid of funds raised through the sale of stock to little old ladies. It is unfortunate that mining promoters are considered crooks until they can prove their integrity and honesty by finding a mine. A common rule of thumb states that for every 1,000 prospects, 100 come to be drilled, and one becomes a mine. However, it is also a statistic that there have been mining promotions, where money raised has gone elsewhere than into the ground; Junior exploration companies can be handy vehicles for unscrupulous financial activity. One must remember though that every stock exchange has had its share of sound mining promotions that, because of the one in 1,000 odds, have failed for legitimate reasons. The promoter must be able to rationalize the worth of a mineral discovery which, on an industry- average basis, probably cost more to find than the discounted value of its net return, which return is not an assured percentage of invested capital, and furthermore, is ultimately from a wasting asset. So, it is easy to understand why the promoter must constantly justify the credibility of his operation to his grubstakers during the course of the "five phases of exploration," those being (1) euphoria, (2) disillusionment, (3) search for the guilty, (4) punishment for the innocent, and (5) distinction for the uninvolved. The promoter with the exploration organization that does not have the benefit of positive cash flow, by definition for the sake of this article, works for a promotional outfit, a Junior Company, that must raise its exploration budget from a variety of sources. Promotion, as discussed here, will not entirely refer to the formation and operation of a joint- stock company but rather to the overall methods of raising risk capital for mineral exploration ventures from outside sources. THE NECESSITY OF PROMOTION In Canada, the publicly financed Junior Company has had an enviable record of mine-finding success. In the Province of British Columbia alone, the discovery of fifteen out of twenty-four mines has been as a result of the activity of the Junior Company (B. C. & Yukon Chamber of Mines, 1977). In the Province of Ontario, one research study indicated that between 1951 and 1974 the &apos;Juniors&apos; spent only 28 percent of the total exploration funds but were responsible for 62 percent of all economic discoveries (Freyman, 1978). The reasons for the success of the Juniors are tied to a variety of factors, the main one being personal initiative based on incentive. In other words, the principals, or their employees have &apos;a piece of the action.&apos; The smaller companies can operate faster and more efficiently than their larger counterparts. The Junior Company is also destined to take some bigger risks, the &apos;long shots,&apos; many of which efforts by virtue of the Junior&apos;s perseverance coupled with a touch of &apos;ore is where you find it&apos; philosophy, result in major discoveries. The individuals, syndicates, private and publicly financed Junior Companies, because of high costs of exploration and development, cannot hope to finance most mineral prospects all the way to production. Exceptions do exist, those being the lower capital cost, small, high-grade deposits. Private investors and publicly financed Junior companies, therefore, can usually afford to finance most exploration through the initial drill-testing stage. The major resource company will enter a mining deal with a Junior Company usually by way of option or joint venture agreement, and will finance to production to earn an equity in the prospect or the Junior Company or both. The conventional lending institutions, banks and government agencies, will usually only participate through loaning a portion of capital

Jan 1, 1985

By AIME AIME

[The American Institute of -Mining Engineers does not assume responsibility for any statement of fact or opinion advanced in its papers or discussions.] A detailed list of the&apos; papers contained in this section is given in the Table of Contents, pages i. and ii. Comments or criticisms upon all papers given in this section whether private corrections of typographical or other errors or communications for publication as "Discussions," or independent papers on the same or a related subject, are earnestly invited. ERRATA. The following corrections and. additions to papers contained in Bi-Monthly Bulletin No. 7, January, 1906,-were received too late for incorporation in the text of said papers ; but will be introduced in their: proper places: in the volume of the Transactions: These corrections are here published in order to bring them -promptly to the notice of the Institute. Page Line Cover, title-page and at the top of pages in the preliminary section "No. 1 " should be "No. 7 ". 1. Bottom For :" Dr. P. H. Shimer" read "Dr. P. W. Shinier " 69. Fig. 3. "N" of compass-record should be ?S". A new block for this illustration has been made as shown on p. xxxviii of this Bulletin. 78. 3 from bottom. For " slope " read " stope." 89. Fig. 2, small diagram in upper left-hand corner. Omit use 50 ft. to 1" scale ". For "Thro&apos; 250 " read " Thro&apos; 200 ". Add dotted line extend¬ing from upper right-hand corner of the square

Mar 1, 1906

By H. A. Wentworth

THE Huff electrostatic plant of the United States Smelting Company operated in conjunction with its wet concentrator at Midvale, Utah, was the second plant of substantial size installed using the Huff process, and the first plant to be put in operation on the so-called Western complex ores. In spite of the machinery being of early design and consequently embracing many of the mechanical weaknesses incident to a pioneer plant the mill has operated steadily and uniformly since the summer of 1909, about five years now, without any material change other than some re-arrangement of the machinery for better handling of the sizes. The ore, at present coming almost entirely. from the company&apos;s mines in Bingham, is of practically the same composition as that upon which the plant was first put in operation. The crude ore, consisting of the sulphides of copper, lead, zinc, and iron, and containing small amounts of gold and silver, is brought by train and delivered to the hoppers of the wet concentrator, where by jig and table treatment, there are produced a shipping lead concentrate, a tailing and a middling product, the latter being conveyed in push cars to the adjoining electrostatic mill. The crude ore delivered to the wet concentrator contains from 6 to 9.5 per cent. zinc. At times the plant is used also for the treatment of custom ores from the Bingham district and elsewhere, and at such times the results of the plant vary according to the material in use, but as by far the larger portion of the product is that from the company&apos;s own mines, the results given below are fairly indicative of the general work obtained. The accompanying diagram illustrates graphically the flow of the ore through the electrostatic mill. The middling coming from the wet mill containing from 15 to 18 per cent. moisture is hoisted while on the cars by an elevator, and delivered from the top of the elevator to a hopper over the drier. The drier first installed was of too low capacity to take care of the moisture present in the tonnage to which the mill was later

Jan 8, 1914

By John Richards

MY remarks will be confined to the experience of our company in mining the No. 8 seam of coal in Ohio, although I believe that the relationship existing here between the method of mining and the method of cleaning will hold true in many of the coal seams throughout the country. The increasing demand for a cleaner and better graded product is being felt throughout the entire coal industry, and the methods of mining are playing an important part in the control of various sizes and quality of coal produced. We have found a definite relation between the mechanical loading of coal and its preparation for the market. In the No. 8 coal seam the location of the non-combustible material is regular. The&apos; marketable coal lies in three benches, separated by streaks or bands of impurities. These impurities must be removed from the coal to properly pre pare the product for the market. Where hand-loading methods are employed, the loader removes as much of this non-combustible material as possible at the working face. The impurities that are missed by the loaders are removed as the coal passes through the preparation plant, by means of picking tables. As this method of cleaning cannot improve the quality of the extremely fine sizes, a practice has been established in the company&apos;s hand-loading mines, of undercutting the coal about 2 in. above the bottom of the seam, thereby eliminating any possibility of impurities caused by the cutting machines cutting into the rock bottom below the coal seam.

Jan 1, 1934

By Duncan MacVichie

The iron fields described here are located in the Iron Springs and Pinto mining districts, Iron County, Utah. This region is in southwestern Utah, about 260 miles south from Salt Lake City, and is reached by the Los Angeles & Salt Lake railroad of the Union Pacific system. The iron fields lie at an elevation of 5500 to 7500 ft. above sea level, and are essentially desert in character. They are covered with a light growth of sage brush, piñon pine, and scattered cedar. Weather conditions are unusually favorable for all-year mining operations, the winters being mild with little or no snow; and the summers not excessively hot, the temperature rarely rising to 100 during the day, while the nights are invariably cool. The iron-ore bearing area extends from the Iron Springs district to the Iron Mountain mining district, being approximately 25 miles long in a northeast-southwest direction, and from 1 to 3 miles wide in a northwest-southeast direction. In the Iron Springs and Pinto mining districts, the ore occurs at various points around three sides of Granite Mountain and Iron Mountain. This is readily understood by reference to Figs. 1-4. These mountains are composed of andesite, which has been forced up through the surrounding sedimentary formation, in the form of laccoliths. An extensive report on the geology of these districts was made by Leith and Harder,&apos; who state: The three dominating geological features of the district are three large andesite laccoliths which constitute the Three Peaks, Granite Mountain, and Iron Mountain; lying in a northeast-southwest line across the area in question. Three unconformable sedimentary series, aggregating 4000 ft. in thickness, outcrop in successive rings around these laccoliths, dipping outward asymmetrically, very steeply at the contact, less steeply farther away. Still farther from the laccoliths, lava-flows 2000 ft. thick rest in nearly horizontal attitudes on the tilted sedimentary rocks. These general relations are modified by faulting. All of the rock formations of the district are more or less covered on the middle and lower slopes by unconsolidated and partly consolidated erosion debris, both aqueous and subaerial, which spreads out on the lower ground to make the deserts.

Jan 1, 1927

By Duncan MacVichie

THE iron fields described here are located in the Iron Springs and Pinto Mining districts, Iron County, Utah. This region is in southwestern Utah, about 260 miles south from Salt Lake City, and is reached by the Los Angeles & Salt Lake railroad of the Union Pacific system. The iron fields lie at an elevation of 5500 to 7500 ft. above sea level, and are essentially desert in character. They are covered with a light growth of sage brush, piñon pine, and scattered cedar. Weather conditions are unusually favorable for all-year mining operations, the winters being mild with little or no snow; and the summers not excessively hot, the temperature rarely rising to 100° during the day, while the nights are invariably cool. The iron-ore bearing area extends from the Iron Springs district to the Iron Mountain mining district, being approximately 25 miles long in a northeast-southwest direction, and from 1 to 3 miles wide in a northwest-southeast direction. In the Iron Springs and Pinto mining districts, the ore occurs at various points around three sides of Granite Mountain and Iron Mountain. This is readily understood by reference to Figs. 1-4. These mountains are composed of andesite, which has been forced up through the surrounding sedimentary formation, in the form of laccoliths. An extensive report on the geology of these districts was made by Leith and Harder,1 who state: The three dominating geological features of the district are three large andesite laccoliths which constitute the Three Peaks, Granite Mountain, and Iron Mountain; lying in a northeast-southwest line across the area in question. Three unconformable sedimentary series, aggregating 4000 ft. in thickness, outcrop in successive rings around these laccoliths, dipping outward asymmetrically, very steeply at the contact, less steeply further away. Still farther from the laccoliths, lava-flows 2000 ft. thick rest in nearly horizontal attitudes on the tilted sedimentary rocks. These general relations are modified by faulting. All of the rock formations of the district are more or less covered on the middle and lower slopes by unconsolidated and partly consolidated erosion debris, both aqueous and subaerial, which spreads out on the lower ground to make the deserts.

Jan 7, 1925

By N. R. Pillai, T. R. Anantharaman

THE striking alterations in the constitution and structure of cast A1-Si alloys brought about by addition of small quantities of some elements, particularly sodium, have been extensively investigated. Many theories&apos; have also been propounded to explain this so-called lLmodification" process, but their main concern has been more to throw light on the action of sodium than to arrive at general criteria underlying this interesting as well as intriguing phenomenon. Such theories have generally dealt with one or more, but not all, factors that seem to have a direct or indirect influence on the cast structure of A1-Si alloys, e.g.., formation of ternary eutectic, removal of oxides, hydroxides, and so forth, by fluxing, morphological changes in silicon, and inhibition of growth of silicon grains through colloidal action, compound formation, preferential adsorption, or reduction of surface tension. Kim and Heine2 were the first to study the modification of A1-Si alloys in a systematic as well as comprehensive manner and to list the important characteristics of a satisfactory modifier. According to them, an important property of the modifying element is its capacity to form a stable compound with silicon in the appropriate temperature range. Other subsidiary requirements are that the element should get adequately dispersed in the melt at the inoculating temperature and also must not form stable compounds with aluminum. The alkali elements, with the exception of lithium, fulfill these requirements most satisfactorily and have been shown to be successful modifiers by these workers. Sodium is the most effective of these and seems to be in a class by itself for various reasons noted by earlier investigators.37 None of the other elements tried by Kim and Heine, viz., Mg, Ca, Cd, Zn, In, Pb, P, As, Bi, S, and Se, showed any significant modifying action. We wish to report here briefly on substantial modifications in cast eutectic A1-Si alloys brought about by some V group elements, which do not comply with the Kim-Heine requirements. Aluminum and silicon used in the present work were indigenous and had purities of 99.8 and 99.5 pct, re-

Jan 1, 1969