Search Documents

By W. Mostowitsh

I. Introductory LEAD sulphate occurs as anglesite, and is formed in every roasting of lead sulphides or sulpho-salts containing lead. In smelting in the blast furnace an ore containing natural or artificial lead sulphate, a large part of the sulphur present goes to the formation of the intermediary product matte which requires further treatment for the recovery of the values it contains. It is therefore of importance to study the behavior of lead sulphate at elevated temperatures, both without and with reducing agents, especially as the information available gives data which are more or less conflicting. II. Decomposition of Lead Sulphate by Heat The dissociation of PbSO4 into PbO and S03 or S02 and 0 has been discussed by many metallurgists. The following data are considered to be representative. Doeltz and Graumann1 found that PbSO4 was not affected by heat at 800° C.; that dissociation began at 900° C., and was rapid at 1,000° when the salt lost in 1 ½ hr. 14.3 per cent. of its weight, the dry salt containing 26.43 per cent. SO3. Hofman and Wanjukow2 summarize their work upon the dissociation of metallic sulphates with the statement that the decomposition of PbSO4 begins at 195° C., but progresses very slowly, with the formation of the basic salt 6PbO.5S03 at 705°; that this salt undergoes a transformation at 847°, begins to be decomposed at 888°, to sinter at 896°, and to fuse at 910°; rapid dissociation begins at 952°, and is accompanied by volatilization of PbO; retardations at 958° and 962° indicate an acceleration of decomposition which, however, is not complete. Proske3 found that PbSO4 gave off at 900° C. in 30 min. only 0.63 per cent. of its SO3, and that the loss increased with

Jan 5, 1916

By J. D. Doherty

That America's great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Increase imports. 3. Develop new sources such as synthetic liquid fuels.

Jan 1, 1949

By W. A. Selvig

BY plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Com-mittee on Coal Classification. This scheme was sponsored by Sub-committee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic.. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as follows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group, 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. , The lignitic class of coal was divided into two groups both below 8,000.B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By T. J. Whalen, S. M. Kaufman

Surface-tension measurements for liquid Fe-C-Co and Fe-C-Ni alloys were performed by the sesszle-drop technique at 1350o and 1425°C. Cobalt was shown to he more effective than nickel in lowering the surface tension of Fe-C alloys A minimum value for surface tension of 1640 dynes per cm was found in the Fe-C-Co system at a concentration of 1.5 pet C and 12pet Co. Analysis of these measurements in terms of adsorption and desorption behavior indicated that cobalt and nickel lower surface tension in Fe-C alloys by replacing carbon at the liquid-vapor interface. Comparison of results to date for Fe-C liquid alloys has shown that most substitutional-type elements having about the same atomic diameter as iron also have relatively the same influence on surface tension when present in dilute amounts. It has been shown previously that surface-adsorption behavior in liquid Fe-C ternary alloys is related to the manner in which the ternary addition affects the activity of carbon in the bulk solution.' Certain ternary additions, such as chromium, tending to decrease carbon activity cause adsorption of carbon and chromium to the liquid-vapor interface. Additions, such as silicon, increase the carbon activity, resulting in a desorption of carbon and an adsorption of silicon. Both cases were shown to cause a decrease in surface tension due to adsorption. It is the object of this paper, as part of the writers' continuing interest in the effect of alloying additions on the surface tension of Fe-C alloys, to present and discuss surface-tension data on solutions in the ternary systems Fe-C-Co and Fe-C-Ni. Available activity measurements for these systems in the solid state indicate a strong increase in carbon activity when either nickel or cobalt is added to Fe-C alloys.2, 3 EXPERIMENTAL PROCEDURE The alloy compositions used are shown in Table I. These alloys were prepared by vacuum melting in stabilized zirconia crucibles and then vacuum casting into cold-steel molds. The nominal analyses for the alloys used in this investigation are given in Table I. Surface tensions and densities were measured by the sessile-drop method4,5 in conjunction with the tables of Bashforth and bdams.' Specimens were prepared by slicing 1/4-in. cubes from the center of the vacuum-cast ingots and grinding the edges of these cubes until their shapes approximated spheres with flat bottoms. Proper handling techniques, including an acetone rinse immediately before use, assured minimum contamination from sources extraneous to the actual melting. For each experimental run a sample was placed on a BeO plaque and positioned and leveled inside a vacuum induction heating apparatus. The sample and plaque arrangement sat inside a molybdenum tube which acted as the susceptor. Diagrams of this apparatus may be found in the literature.= After heating to temperatures just above the liquidus at pressures of the order of 10-4 to 10- 5 mm Hg, photographs of the drop profile were made using its natural thermal radiation as a light source. Some measurements were made with partial pressures (-1 cm Hg) of a mixture of H2 and He gases. The H2-He atmospheres proved to be necessary at higher nickel contents to retard excessive vaporization losses. Chemical analysis for carbon and the ternary addition was performed for each alloy sample after completion of the experimental run.

Jan 1, 1964

By D. W. Mitchell

J. H. Schlobohm (Joy Manufacturing Co., New York) —This paper has been read with a good deal of interest; however, there are several salient features which Mr. Mitchell has overlooked. The initial emphasis on selection should be placed on type of material to be loaded and method of mining involved. There is no possible connection in the comparison of scraper or Joy Lohite loaders with loaders of any other type. Neither can an operating comparison be made between "Rocker type" loaders and those equipped with loading head and gathering arms. Each unit has its application, but the application depends on material and the mining system involved. Mr. Mitchell's compilation of data on various loaders, while it represents a great many facts, does not represent true operational data, i.e. Table I, column heading "Max. Rated Capacity for 7 hr;" these figures are meaningless inasmuch as little or no time at all is allowed for tramming or switching or moving the loader from place to place. Table I, column heading, "Best Reported Field Shift," would be a better source of operational data, assuming of course that conditions, applicable to each class of loaders, were average to avoid enthusiastic performance figures. Table I, column heading, "Repair Parts Cost per Ton," is still another item which will not stand up under comparison unless the loaders involved are put into type classes, i.e., there are simply no means possible to show the repair costs of scraper loading versus a caterpillar mounted loader in abrasive material. The source of information here is also important. Actual field tests have proved that these costs are of a constant nature. Manufacturers are striving to hold them to a minimum and many interesting studies have been made. A fairly recent example of this in a large United States gold producer has proved that Joy HL-3 loaders can be consistently average, less than $0.025 per ton mucked. This cost represents repair labor and parts over a two year

Jan 1, 1952

By Ralph Arnold

The lure of possible new oil fields shut off development of the older Montana fields during the year 1928, cutting down the total production to less than the 1927 mark. However, with the production of oil worth approximately $7,000,000 during the past 12 months, Montana oil producers pushed their total up to $44,000,000 taken from two principal fields during the past 8 years. The highest prices in the United States for oil of similar gravity gave northern Montana producers a decided advantage and brought up the value of the oil to about the same value as the 1927 production, although the oil runs were 1,000,000 bbl. less. Production by Fields The discovery of two new oil fields in the Sweetgrass Arch, in north central Montana, in 1927, diverted attention from the Kevin-Sunburst field. Many operators turned their attention to wildcats and practically all of the drilling contractors were called into the new Pondera and Bannatyne fields. Although discovered in 1927, the Pondera field developed its first commercial production in March of 1928. Mild interest was followed four months later by a rush of operators, and by August practically every string of tools had been moved from the Kevin-Sunburst field to Pondera. The fall months found 40 wells drilling in this field and as the year closed there were 100 producers. Pondera field is remarkable in that every well thus far drilled within the structure proper has been a producer. Dry holes have been drilled around the field, but none within an area of four sections. Experts estimate that Pondera will produce 5000 bbl, of oil to the acre. The producing area now outlined by wells drilled is expected to produce around 15,000,000 bbl. of oil. Pondera crude brings $1.75. This field has one pipe line and a second line is being laid. Lack of a pipe line delayed development of the new Bannatyne field, south of Pondera, and also in the Sweetgrass Arch. Bannatyne has 11 producing wells scattered over an area of approximately three sections. Bannatyne is a sand field with a 70-ft. sand in the lower Jurassic, which core-drill tests show to be 60 per cent. saturated. With the completion

Jan 1, 1929

By Keats, J. L.

IN THE literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical charac- teristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete as data possible on all the factors that affect the elimination of metalloids were obtained.

Jan 1, 1957

By F. L. Bosqui, A. D. Wilkinson

EVEN though the world has not been crying for more copper for the last three or four years there has been some important mill and smelter construction. Discovery and development of large new high-grade copper deposits in Africa has led to the construction of extensive reduction facilities there, prominent among which is the concentrator and smelter of the Rhokana Corporation at N'Kana. Northern Rhodesia. The 3000-ton concentrator adjoins the central shaft. A little over half a mile to the southeast, at an altitude of 40,010 ft., is the smelter, designed on the site by 1. H. Wynne. It is arranged primarily to treat N'Kana copper concentrates, but can also handle concentrates and direct-smelting ore from outside sources. Excavations were started late in 1930; concrete was first poured on Jan. 6. 1931; and the first blister cop¬per was cast on March 1.9, 1932, less than fifteen months later. During this period, which included several months of heavy tropical rains, some 10,000 cu. yd. of concrete was poured and 41000 tons of structural steel erected under the supervision of construction engineer, A. Ek, with a labor force of 60 to 30 Europeans and about 300 natives. The steelwork was fabricated by Head Wrightson & Co. in England, and the boiler plant equipment furnished and erected by the International Combustion Co. Ltd.

Jan 1, 1934

By J. E. Tobey

NATIONAL DEFENSE should not create a dilemma in coal utilization such as obtained during the World War. Even under the heavy pressure of a total preparedness program there should be a smooth flow of the right coals from mines to plants. The more than 100,000 industrial plants of the nation must he served with coal of such characteristics and qualities for their individual requirements that no loss of production due to coal failure shall occur. This problem challenges the ingenuity and cooperativeness of producers. transportation executives, consumers and engineers.

Jan 1, 1941

By Edward Gridley

Members of the Institute who were present at the Amenia, N. Y., meeting, in October, 1877, will remember their visit to the hematite mines, just west of the village of Amenia, and some of them may perhaps recall the deposit of carbonate ore south of the opening made for the hematite. The smelting of this carbonate during the last few months, has produced an iron that seems worthy of being brought to your notice. A little more than a year ago, at the Wassaie Furnace, Dutchess County, N. Y., we made a few hundred tons of iron from a mixture of two-thirds ram carbonate and one-third Chateaugay ore, hoping that it would be suitable for steel purposes, but as the iron showed phosphorus 0.189 per cent., it, was not offered. This iron looked well and seemed quite strong, and gave good results in malleable castings; but no special tests of strength were made. About February 1st, of this year, we began using two-thirds roasted carbonate, and one-third Chateaugay, and noticing that the iron mas stronger than usual, we had two samples tested, which showed tensile strength of 32,014 and 34,176 pounds per square inch. After our stock of Chateaugay ore was exhausted, me put on one-third ram carbonate with the two-thirds of roasted carbonate, and the first test made of the iron, showed 40,008 pounds per square inch. The three tests given above were made by Mr. A. J. Copp and Mr. E. B. Manning, of the Phoenix Furnace, Millerton, N. Y., on a machine of Riehle Bros., Philadelphia. Since these tests were made, they have broken samples made with all carbonate ore as follows: 39,669, 40,816, 41,882, 42,281, 39,902, and 40,130 pounds per square inch. A test taken from the same bed of iron as the last-mentioned (40,130), was broken by Mr. A. Blass, at Irondale Furnace, showing 40,151 pounds per square inch. A sample broken on the Riehle Bros. machine, at Stevens Institute, under direction of Professor R. H. Thurston, showed 40,000 pounds per square inch. Another sample was broken by Professor Thurston on his torsion machine, and gave torsion 7", and tensile strength of 44,500 pounds. And

Jan 1, 1884

In response to Dr. Ledoux's paper, a large number of metallurgical establishments and individual assayers expressed their willingness to co-operate in the plan he proposed. The necessary samples were prepared as follows : Matte.—A car-load of matte was put through a Blake crusher, then automatically subdivided into tenths by a Taylor and Brunton sampler, and one-tenth passed through Cornish rolls and through a 12-mesh screen. This was again subdivided by an automatic sampler into tenths, and a final tenth, representing 1 per cent. of the original lot, was finished by hand-sampling on an iron floor until 100 pounds remained. This was pulverized to pass a 40-mesh screen and then thoroughly mixed and divided in the presence of my assistant for distribution to the parties co-operating. Copper Borings.—These were taken from a lot of anodes, the dip-samples from several batches having been united, remelted and cast into a plate, which was proved by assay to be of uniform quality in its different parts. Borings from this plate were intimately mixed and divided in the presence of my assistant. Samples were sent out November 1,1894, with the following letter: New York City, November 1, 1894. Samples of matte and copper (about I pound each) carefully prepared in the presence of my assistant and sealed with his seal as below, are sent you by express for assay and report according to the plan of Dr. Ledoux. These samples are constituted about as follows: Matte. Copper. From. To. From. To. Copper, per cent.,.....50 60 ..........., Gold, oz. per ton,.....2 3 0.20 0.50 Silver, oz. per ton,.....100 150 140 180

Jan 1, 1896

By Bieniawski, Z. T.

The importance of understanding the phenomena associated with rock fracture has long been fully appreciated in rock mechanics. This is clearly apparent from the special attention paid to rock fracture in the comprehensive papers published within the past four years. These papers present a picture of how the knowledge of brittle fracture of rock was gradually enriched and also show that what was often taken for granted three or four years ago is no longer considered as valid today.

Jan 1, 1972

By Corale Brierley

The effect of hydrogen peroxide (H202) on growth and respiration of Thiobacillus thiooxidans and Thiobacillus ferrooxidans, organisms involved in acid leaching of copper sulfide minerals and uarnium oxides, was examined. Oxygen uptake and growth by T. thiooxidans were totally inhibited after contact with 0.82 mM H202. Complete inhibition of oxygen uptake by T. ferrooxidans occurred at 8.75 mM H202, and growth was inhibited after 6 hr exposure to 2.06 mM H202. Higher concentration of H202 can be used without detriment to thiobacilli if it is dissipated prior to reaching the oxidation pond or dump surface.

Jan 1, 1980

By R. J. Lytle, E. F. Laine

The in situ high frequency electrical conductivity and permittivity of Colorado oil shale were recently measured. The measurements were made at 45 MHz (45 million cps) by transmitting from one borehole to two receiving boreholes, all boreholes in line. A differential measurement using the received signals was used to calculate the conductivity and permittivity.

Jan 1, 1983

By James T. Gow, Oscar E. Harder, Anton de S. Brasunas

THIS paper deals with the results obtained and the techniques employed in determining: I. Liquidus and solidus temperatures of the HH and HT type heat-resistant alloys. † 2. The relation of true temperatures (thermocouple) to apparent temperatures (optical pyrometer) for the molten HH and HT type alloys. This work was the outgrowth of needing to know something definite about these temperatures in order to study the effect of pouring temperatures, shake-out times, and heat-treatments on the properties of some heat-resistant alloys. The information developed is thought to be of interest to industry for guidance in foundry practices and the industrial heat applications of the alloys. This paper is based upon work that has been done for the Alloy Casting Institute at Battelle Memorial Institute. LIQUIDUS AND SOLIDUS TEMPERATURES OF HH AND HT TYPE ALLOYS Experimental Procedures Temperature-time curves were obtained during the cooling and solidification of several HH and HT type alloys. The metal was melted in an Ajax high-frequency induction furnace and poured into a coresand mold for cooling. The temperature measurements were obtained by means of a platinum, platinumrhodium thermocouple contained within a fused silica sheath, which was extended through the side wall of the dry core-sand mold to a point at about the center of the mold cavity, which was 3 in. in diameter by 5 in. deep. The cold junction of the thermocouple was kept in an ice bottle, and the temperature was recorded automatically on a direct-reading potentiometer recorder. Through a switching arrangement, the temperature recorded was checked occasionally with a portable Leeds and Northrup potentiometer indicator. Less than a 5°F. variation in the two instruments was always found. This is within the limit of accuracy of readings. The thermocouple used was checked for accuracy against a standard couple, both before use on this work and after completion of the work, by the instrument laboratory. Temperature-time Cooling Curves Fig. I is an enlarged reproduction of a part of one of the cooling curves over the temperature range of 2600° to 2200°F. for an alloy of the HT type with 0.45 per cent carbon, 16 per cent chromium, and 36 per cent nickel. This is a typically shaped cooling curve as obtained for the alloys. It will be noted that two temperatures are shown on Fig. r for the liquidus temperature. It is thought likely that the higher temperature, A, at the point at

Jan 1, 1945

By N. O. Taylor

THE failure, by swelling, of several cast aluminum-zinc, spiral, pump rods, used to circulate water in a constant-temperature bath, brought up the question as to whether the presence of tin in varying quantities would have any appreciable influence in controlling this action. Previous workers had found the same difficulty with aluminum-zinc alloys, due to their swelling in water or solutions of electrolyte^.^ It was known that pure aluminum was practically insoluble in concentrated sulfuric and nitric acids, presumably due to the formation of an oxidized film on the surface. Concentrated sulfuric acid had little or no effect on pure zinc and tin and concentrated hydrochloric acid would attack all three metals. These facts aroused curiosity as to the probable reaction of the ternary alloys of these metals, and tests were made to determine their resistivity to the action of common laboratory reagents. Samples, covering the entire range of the ternary series of aluminum, zinc and tin alloys, were made up from good grades of the commercial metals.2 The materials were melted, at as low temperatures as possible, in graphite crucibles in a gas-fired crucible furnace. Graphite crucibles were used in preference to clay, to prevent the absorption of silicon by the aluminum, as found by previous workers. The melted materials were stirred thoroughly with pine sticks in order to ensure complete mixing and the greatest possible freedom from oxidation, and were cast in sectional, iron molds giving bars % in. in diameter and 5 in. long.

Jan 1, 1927

By V. F. Zackay, W. A. Goering

ALLOYS of iron and aluminum up to 35 wt pct aluminum are single-phase solid solutions, and are of potentially wide applicability.1-3 In spite of early and continued interest1-4 little progress has been made until recently in the preparation and evaluation of sound alloys containing more than 6 wt pct aluminum. Vacuum-melting techniques for the production of ductile Fe-A1 alloys have been described recently.1-7 A. procedure for air melting these alloys is presented here. Low-carbon iron is induction melted without a slag in a rammed magnesia crucible. At the beginning of melt-down, aluminum pig (99.95 pct Al), charged in a clay-graphite bottom-pouring crucible is placed in a pot furnace at 1800°F. The primary deoxidation of the molten iron after melt-down is effected by the addition of 0.1 pct aluminum and 0.5 pct manganese. (Hilty and Crafts" have reported a significant increase in the deoxidation efficiency of the aluminum and manganese combination over that of the aluminum alone.) A more drastic deoxidation designed to reduce the oxyen content to the lowest possible level is accomplished by plunging metallic calcium to the bottom of the melt. This is done by wiring small cubes of the metal to a steel rod. A circular shield larger than the diameter of the crucible opening is attached to the rod so that any spa'ttering of the molten metal will not endanger the operator. Since the temperature of the molten metal is above the boiling point of calcium, the bath is vigclrously purged by calcium vapor. It is believed that the calcium-vapor treatment permits a homogeneous distribution of calcium in the melt. Owing to the vigor of the reaction the temperature of the molten metal should be kept below 2900°F prior to the calcium addition. A total of 0.05 pct calcium is added in two stages in this manner. The second calcium deoxidation is made just before charging the molten aluminum into the iron, in order that an excess of calcium be present for the remainder of the melt. The aluminum, which has been removed from the holding furnace, is then hydrogen degassed by bubbling chlorine through a quartz tube immersed in the molten aluminum. The hydrogen-chlorine reaction is an exothermic one preventing the solidification of the aluminum during the 5-min chlorination. Approximately 0.1 pct calcium, based on the amount of aluminum, is then added to the aluminum. A further excess of calcium is introduced into the melt in this manner. The oxide dross is removed, fluorspar is added to the molten iron, and the molten aluminum is poured through the fluorspar slag. The fluorspar should be dried thoroughly prior to its use, as any water present will react with the aluminum. Aluminum oxide formed during the pouring operation reacts with the fluorspar slag to form gaseous aluminum fluoride and calcium oxide. A forced-draft ventilating system is required for this operation as aluminum fluoride is toxic. As soon as the molten aluminum has been added, vigorous manual stirring of the melt is required because the slag-aluminum oxide reaction is highly exothermic and tends to take place near the top of the melt. The combination of high temperature and the slagging action of the fluorspar quickly erodes the crucible at the slag line if the aluminum is not stirred uniformly into the melt. It has been found that at least 4 min of manual stirring combined with induction stirring are necessary to ensure homogeneity. The power is shut off 1 min prior to pouring to allow metal and slag to separate. As much slag as possible is removed from the melt, which is then poured directly into cast-iron molds. A mold wash of aluminum oxide is used to prevent ingot sticking. For slab ingots which are to be rolled into sheet, a carbon-tetrachloride vapor atmosphere or a chlorinated-pitch mold wash is desirable, as the aluminum oxide formed in the pouring operation is subsequently removed by the chlorine in the presence of carbon." As in vacuum melting, a pouring temperature of about 2900°F is recommended. Adequate hot-topping is important as iron-aluminum ingots are subject to very deep piping. Ingots are removed from the molds and buried in vermiculite, where they are allowed to cool slowly to room temperature. The ingots are radiographed,

Jan 1, 1959

By Tell Ertl

THE Piceance Creek Basin in northwestern Colorado is believed to contain the richest large deposit of oil shale in North America. The major portion, about 1650 sq miles, is bounded by the White River on the north, the Grand Hogback, which runs from Meeker to Rifle, on the east, the Colorado River to the south, and the drainage basin of Salt and Douglas Creeks on the west. The Basin is a plateau 7000 to 9000 ft high, composed of 3000 ft of the Green River series of Eocene age and surrounded by a steep escarpment of 1000 to 3000 ft. From the escarpment the beds dip gently toward the center. Although oil shale is found in all members of the Green River series, the rich thick beds are found chiefly in the Parachute Creek member. This is normally capped by 100 to 200 ft of the Evacuation Creek, the youngest member of the Green River series. Actually the Piceance Creek Basin oil shale is not a shale, nor does it contain oil. It is magnesium marlstone holding solid organic matter capable of being broken down by heat into gases, some of which can be condensed into oil. The marlstone is resilient nonporous rock, difficult to sample by pick or hammer and moil. Many companies and individuals prospected the Colorado oil shale shortly after the first World War,' see Fig. 1, but because of the discovery of large quantities of petroleum in the late 1920's in Cali- fornia, Oklahoma, and East Texas, interest in oil shale development waned and did not revive until World War 11. In 1944 the writer, employed by the Bureau of Mines, prospected the high grade oil shale in numerous places along the southern outcrop of the Piceance Creek Basin. Several channel samples about 100 ft in length were cut, see Fig. 2. An eight-man crew needed a week to cut a satisfactory channel 80 ft long in the cliff face. The Phillips Petroleum Co., the Union Oil Co. of California and others also prospected the oil shale outcrop. In 1945 the Bureau of Mines initiated a core drilling program for the purpose of obtaining accurate samples from the Piceance Creek Basin. The U. S. Geological Survey set up a program for the geological study of the Basin that is still going on." Until the end of 1951 a total of 31 holes was drilled for core with diamond drills, and, in addition, cuttings through the oil shale have been obtained from 4 gas wells drilled by standard rotary oil well rigs. The Bureau of Mines drilled 12 of the holes, the Union Oil Company of California 8, the Standard Oil Company of California 6, the Sun Oil Company 3,

Jan 1, 1953

By Tell Ertl

THE Piceance Creek Basin in northwestern Colorado is believed to contain the richest large deposit of oil shale in North America. The major portion, about 1650 sq miles, is bounded by the White River on the north, the Grand Hogback, which runs from Meeker to Rifle, on the east, the Colorado River to the south, and the drainage basin of Salt and Douglas Creeks on the west. The Basin is a plateau 7000 to 9000 ft high, composed of 3000 ft of the Green River series of Eocene age and surrounded by a steep escarpment of 1000 to 3000 ft. From the escarpment the beds dip gently toward the center. Although oil shale is found in all members of the Green River series, the rich thick beds are found chiefly in the Parachute Creek member. This is normally capped by 100 to 200 ft of the Evacuation Creek, the youngest member of the Green River series. Actually the Piceance Creek Basin oil shale is not a shale, nor does it contain oil. It is magnesium marlstone holding solid organic matter capable of being broken down by heat into gases, some of which can be condensed into oil. The marlstone is resilient nonporous rock, difficult to sample by pick or hammer and moil. Many companies and individuals prospected the Colorado oil shale shortly after the first World War,' see Fig. 1, but because of the discovery of large quantities of petroleum in the late 1920's in Cali- fornia, Oklahoma, and East Texas, interest in oil shale development waned and did not revive until World War 11. In 1944 the writer, employed by the Bureau of Mines, prospected the high grade oil shale in numerous places along the southern outcrop of the Piceance Creek Basin. Several channel samples about 100 ft in length were cut, see Fig. 2. An eight-man crew needed a week to cut a satisfactory channel 80 ft long in the cliff face. The Phillips Petroleum Co., the Union Oil Co. of California and others also prospected the oil shale outcrop. In 1945 the Bureau of Mines initiated a core drilling program for the purpose of obtaining accurate samples from the Piceance Creek Basin. The U. S. Geological Survey set up a program for the geological study of the Basin that is still going on." Until the end of 1951 a total of 31 holes was drilled for core with diamond drills, and, in addition, cuttings through the oil shale have been obtained from 4 gas wells drilled by standard rotary oil well rigs. The Bureau of Mines drilled 12 of the holes, the Union Oil Company of California 8, the Standard Oil Company of California 6, the Sun Oil Company 3,

Jan 1, 1953

By Everett D. Jackson

The largest deposits of chromite in the United States occur in tabular layers in the lower part of the Stillwater Complex, Montana. Nearly 900,000 long tons of chromite concentrates have been produced from mines and mills in this area, and reserves equivalent to more than 2,500,000 long tons of Cr2O3 remain in the ground. Layered concentrations of chromite (known as chromitite zones) occur only within olivine-rich layers of the Peridotite member of the Ultramafic zone of the Stillwater. As many as thirteen chromitite zones, lying conformably one above another, have been found, but only five of them are thick enough to be of any conceivable economic interest, and only two of them have been mined to date. Individual chromitite zones can be recognized by their distinctive internal character and by their stratigraphic position in the Peridotite member. The chemical composition of chromite varies consistently between and within the different chromitite zones. The zones range in thickness from about an inch to more than 12 feet, and the Cr2O3, content of their chromite ranges from 36.6 to 49.2 weight per cent. In any given area, the G chromitite zone is the thickest, but the chromite of the H chromitite zone has the highest grade. Laterally, the thickness of the chromitite zones is related to the thickness of the Peridotite member; in general all are thicker in the eastern part of the Stillwater than in the western part.

Jan 1, 1968