Search Documents

By Edward Hart

The specimen of glazy iron used for analysis was highly characteristic in appearance. It was made at one of the furnaces of the Glendon Iron Works, working a light burden of ore with a highly silicious cinder. There are very few records of analyses of this variety of iron. I have been able to find but the two given by Bell, and I add these to my analysis for comparison. Bell. 1. 2. Iron,......89.47* 88.18 90.70 Carbon, combined,.... 0.00 0.79 0.71 Graphite,......2.88 2.59 2 68 Silicon,......5.47 5 13 5.13 Manganese,.....1.54 0.77 0.56 Sulphur,......0.04 0.17 0.23 Phosphorus,.....0.60 1.12 1.12 Titanium,.....- 0.26 0.18 Calcium,......0.00 0.22 0.20 Magnesium,.....0.00 0.06 0.03 100.00 9929 101.54

By S. Paul Lindau

THREE years ago it was decided by the management to granulate the matte that is produced in the smelter of the St: Joseph Lead Co. at Herculaneum, Mo., thereby doing away with a large amount of labor in handling the matte and in subsequent crushing. On Mar. 1, 1915, the granulator was put in operation and up to Jan. 1, 1916, 18,735 tons had been, granulated. The four blast furnaces have a daily output of about 280 tons of pig lead and 100 tons of matte assaying about 11.0 per cent. Pb. It is expected that projected improvements in roasting methods will eliminate more sulphur from the charge, and cut down the matte-fall, to about one-half of the present figure. The blast furnaces are tapped into movable forehearths or settlers, 6 ft. by 4 ft. by 22 in., the slag overflowing into 27-cu. ft. slag cars which are hauled to the clump by electric locomotives. Previous to the adoption of granulation, the matte was tapped from the forehearths into small slag pots which were dumped after cooling. The matte cakes were broken with sledges, and transported to the crushing plant for fine crushing and screening. Here the matte was reduced to ¼ -in. size before being fed to the roaster bins.. A Wedge and a Holthoff mechanical furnace are used for preroasting before sintering on the Dwight and Lloyd machines. The matte is returned to the furnaces as an iron flux until the .gradually accumulating copper content reaches about 7 per cent., after which it is put aside to be concentrated in a small copper blast furnace, the resultant high-grade matte-being sold. When the matte does not settle readily from the slag, two settling devices are often used, the second one being a large catch-pot, which gathers any matte that may overflow from the forehearth, the slag then overflowing from the catch-pot into the slag cars. When full of matte, the catch-pot is removed, allowed to cool, and the contents broken and crushed.

Jan 10, 1916

By M. A. Scheil

Austenitic stainless alloys are susceptible to stress-corrosion cracking which may occur under certain corrosion environments irrespective of their susceptibility to intergranular corrosion. Test samples are described for investigating stress-corrosion susceptibility of alloys for industrial equipment. A laboratory test using a solution of magnesium chloride boiling at 309 F. was found to produce transgranular cracks in several alloys investigated and in types 347 and 316 stainless steel tubing a residual stress of the order of 10,000 psi. was observed to initiate cracking. The susceptibility to stress-corrosion cracking as judged by the boiling magnesium chloride test indicates that alloys may be selected which will withstand a high stress in service Stressed specimens of stainless alloys included in a corrosion testing program will aid in determining the acceptibility of these fabricated alloys, when stressed, to the service conditions.

Jan 1, 1945

By Arnulf Muan, D. P. Masse

PHASE relations in the system CoO-SiO2 have been determined as a basis for further investigations of thermodynamic properties of olivine solid solutions involving Co2SiO4 as a component. Previous data on the system CoO-SiO2 are incomplete or uncertain. Biltz and Lemke1 determined the melting point of cobalt orthosilicate as 1345°C , but Asanti and Kohlmeyer2 have later found a considerably higher temperature, 1420°C. The latter authors also studied melting relations of one mixture on the CO side and two mixtures on the SiO2 side of the orthosilicate composition and sketched a tentative phase diagram for a limited composition range of the system. However, no phase identification was carried out, and the authors left unanswered the question of the possible existence of a stable meta-silicate phase. Greig3 showed that a 90 wt pct SiO2-10 wt pct Co mixture at 1725°C consists of two immiscible liquid phases. The quenching technique was used in the present investigation. Mixtures of high-purity cobalt oxide ("Fisher Certified") and dehydrated silicic acid ("Baker Analyzed") were equilibrated in air atmosphere. The samples were then quenched to room temperature and the phases present were identified by microscopic and X-ray examination. The samples were kept in small envelopes made from thin (0.0004 in.) platinum foil. Thermodynamic data which have become available recently for Pt-Co alloys4 were used to check that the losses of COO from the oxide samples by alloying of cobalt with platinum in the present investigation were too small to change significantly the compositions of the oxide material during the equilibration. A vertical tube furnace with an 80 pct Pt 20 pct Rh resistance winding was used in runs up to 1510°C. Temperatures in these runs were measured with a Pt vs 90 pct Pt 10 pct Rh thermocouple calibrated against the melting point of diopside (CaMgSi2O6, 1391.5?C). The given temperatures as measured by this technique are estimated to be accurate to *5°C. Quench runs at temperatures above 1650°C were made with a modified Roberts and Morey5 strip furnace, using strip resistors composed of a 60 pct Pt-40 pct Rh alloy. Temperatures were measured with an optical pyrometer which was calibrated against the liquidus temperature of a mixture composed of 10 wt pct CaO, 90 wt pct SiO2 (1707°C). The temperatures measured with this technique have an estimated accuracy of +15°C. The results are shown graphically in Fig. 1. Only one intermediate phase, the orthosilicate Co2SiO4 with olivine-type structure, is stable in addition to the end members cobalt oxide and silica. The melting point of the orthosilicate was found to be 1415" ± 5°C. The metastilicate CoSiO3 is not stable at the temperatures of the present investigation. The two eutectic points in the system CoO-SiO2 where COO plus olivine, and olivine plus silica, coexist with liquid were found to be 72 wt pct COO and 1407°C and 63 wt pct COO and 1381°C, respectively. The melting point of cobalt oxide in air was taken as 1745?C, based on the previous data of Aukrust and Muan.6 Within limits of error (+ 5?C), identical eutectic temperatures to those determined in air were found when two representative mixtures were equilibrated at 1 atm O2 pressure and in an atmosphere of 84 vol pct CO2, 16 vol pct H2. This suggests that changes in oxidation state of cobalt in the condensed phases are not significant as far as their effect on the phase relations are concerned. This inference was substantiated by failure to detect7 any "excess oxygen" (i.e., oxygen in excess of that contained in Co2SiO4) in a sample of orthosilicate composition equilibrated in air 10°C above the liquidus temperature and subsequently quenched to room temperature. This work was carried out as part of a research program sponsored by the U.S. Atomic Energy Commission under Contract No. AT(30-1)-2781.

Jan 1, 1965

By H. M. Hobart

This paper deals principally with investigations undertaken by the Welding Research Sub-committee of the Welding Committee of the Emergency Fleet Corporation. The general object of the investigations has been to extend the use of welding in the construction of merchant ships and, specifically, to provide a definite basis for obtaining the greatest economy and efficiency in employing welding in place of riveting in the construction of the hulls of such ships. Composition of_ Ship-plate Steel The chemical composition of the steel employed in such hull construction varies with the thickness of the plates. Through the courtesy of Mr. H. Jasper Cox, of Lloyd's Register of Shipping, the following information may be given concerning the kind of steel plate employed in American shipyards in 1918 for the hull construction of merchant ships. Lloyd's requirements do not relate to the chemical composition. They require a tensile strength of 58,000 lb. per sq. in. (40.75 kg. per sq. mm.) for their lower limit and 72,000 lb. per sq. in. (50.59 kg. per sq. mm.) for their upper limit. For the information of the Committee, Lloyd's obtained from their surveyors at various works data of the carbon content, which is as follows: Works Carbon Content for Plates 1/4 In. Thick 1 In. Thick A..................... 0.14 0.23 B..................... 0.14 0.25 C2.................. 0.19 0.25 D................. 0.20 0.30 E Upper limit..... 0.35 Lower limit..... 0 24 0.29 Upper limit,.... 0.25 0.30 Lower limit..... 0.21 0.27 Upper limit..... 0.25 0.35 Lower limit..... 0.22 0.28

Jan 1, 1920

By P. G. Winchell, A. J. Heckler

An experimentally simple method for determining the effect of alloying elements on the activity of carbon is validated in Fe-Ni-C austenite. The technique consists of the equilibration of carbon between specimens of different nickel contents within a sealed silica capsule. The attainment of carbon equilibrium within each capsule is evidenced by: 1) in each capsule specimens of the same nickel content attained the same final carbon content regardless of their initial carbon contents, 2) in every capsule the final carbon content was reached for most nickel contents by carburizing and by decarburizing. The activity of carbon attained within each capsule was calculated from the carbon content of a binary Fe-C alloy placed within the capsule, and from the activity coefficient of carbon in the Fe-C system as found by Smith for CO/CO2/C equilibrium. The activity of carbon in Fe-Ni-C austenite determined by this method at 1000°C agrees with prior work by Smith, who used mother method. The measurements are extended to 800°and 1200°C. The activity coefficient of carbon 7c, in Fe-Ni-C austenite is given by: where xC is the ratio of carbon to metal atoms and XNi is the ratio of nickel to metal atoms and where the standard state is chosen such that yC = 1 as xc approaches zero in Fe-C alloys. This equation appears to be valid for xni < 0.3, and 1073° < T<1473°K. ThE activity of carbon in Fe-C austenite has been measured by smithL at 800°, 1000°, and 1200°C. Smith has also studied the effect of nickel on the activity A. J, HECKLER and P. G. WINCHELL are Graduate Student and Associate Professor of Metallurgical Engineering, respectively, School of Metallurgical Engineering, Purdue University, Lafayette, Ind. This paper is based on a thesis submitted ty,to Purdue University, in partial fulfillment of the requirements for the degree of M.S. in Metallurgical Engineering which A. J. HECKLER received from Purdue in January 1962. Manuscript submitted August 13, 1962. IMD of carbon in austenite at 1000°C. In both these studies the activity of carbon was fixed by a flowing CO-C02* *Gas mixtures of hydrogen and methane were also used in Ref. 1 but these results are not incorporated in Ref. 2 or in the present study. gas mixture. In the present work, Smith&apos;s results for Fe-Ni-C austenite are confirmed and extended to 800" and 1200°C by a different experimental technique. EXPERIMENTAL PROCEDURE In essence the experimental technique consisted of enclosing specimens of various nickel contents in an initially evacuated silica capsule and annealing the capsule until carbon equilibrium was attained among the enclosed specimens. The carbon activity obtained within the capsule was determined from the final carbon content of the binary Fe-C alloy included in each capsule and the results of smith.&apos; In order to evaluate this method the absence of nickel transfer between specimens must be established and the attainment of carbon equilibrium between samples must be assured. The absence of nickel transfer was demonstrated in the case of an originally pure iron sample which was annealed at 1200°C in a capsule with a 27.3 at. pct Ni alloy. The final nickel content of the iron specimen was less than 0.1 at. pct, a change which has a negligible effect on carbon activity. The attainment of carbon equilibrium was demonstrated within every capsule and in over half the results by achieving the same final carbon content in a sample which carburized during equilibration and in a sample of the same nickel content which decarburized during equilibration. The base Fe-Ni alloys were vacuum melted from Ferrovac E or electrolytic iron and Mond or electrolytic nickel. The samples were rolled and/or swaged and their carbon content adjusted to the desired pre-equilibration level either by methane-hydrogen carburization or by direct carbon transfer from a graphite source in a sealed silica capsule. As mentioned previously, high-carbon and low-carbon samples were prepared for most nickel levels in each capsule. The specimens were cleaned and

Jan 1, 1963

By H. A. J. Wilkens, H. B. C. Nitze

From time to time papers treating of specific cases of Southern gold-mines and mining have appeared in the Transactions of this Institute, as well as in other journals and publications. Mr. George I?. Becker, of the United States Geological Survey, made a reconnaissance of the Southern Appalachian gold-belt during the fall of 1894; the results of his investigations are published under the title of "A Reconnoissance of the GoldFields of the Southern Appalachians," in the Sixteenth Annual Report of the Director of the United States Geological Survey, 1894-95 : Part III., " Mineral Resources of the United States." Mr. Becker has treated the subject mainly in a scientific geological manner. We present this paper to the members of the Institute as requested by the Secretary last May, with the object of covering the ground from a more practical and technical standpoint. The notes for this paper were made in a large measure from personal observations, gained chiefly during the past summer on a trip through the field. In connection with this trip we collected a suite of typical hand-specimens, representing the gold-ores and wall-rock from the more important localities. This collection forms a part of the exhibit

Jan 1, 1896

By Dever C. Ashmead

Anthracite was first mined in the Wyoming Valley and sold as an article of commerce in 1808. As some preparation has always been necessary to make it ready to burn, the preparation of anthracite must date back over a hundred years. Two vital factors have determined to a large extent the degree and the method of anthracite preparation. These are, first, the character of the beds worked and the methods by which they are mined and, second, the equipment used and practices followed in the burning of the coal. It is not the intention here to go deeply into these phases of preparation as a paper of no mean length could be prepared on the history of either. Rather, the intention here is to point out the main considerations and to show the influence they have exerted on the preparation of anthracitc. Mining Methods and Their Relation to Preparation In the beginning of the nineteenth century, the coal beds were virgin with the possible exception of some outcroppings that had been worked, to a slight extent, by the Indians. It is known that the American aborigines had a, knowledge of the use of this fuel, because when the Wyoming Valley was purchased from them, in 1754, they mentioned the fact that, by selling the land, they would lose their coal. Real mining of anthracite began about 1808 when Judge Jesse Fell, of Wilkes-Barre, discovered that the "common stone coal of the valley" could be burned in an open grate. For some years thereafter mining was conducted near the surface. The working p1aces were driven narrow; only the best of the coal was selected and the remainder was left in the ground. Only the lumps could be used, as no market existed for other sizes. As time passed, however, it became necessary either to go farther into the ground or to widen the working places. When these places were widened, falls of roof were apt to occur, making it necessary

Jan 1, 1922

By J. B. Bassett, E. S. Rowland

The experimental work reported herein firas inspired by the publication of a paper by Grange and stewart, in which it was suggested that at low chromium contents the effect of this element on the Ma point was greater than at higher chromium contents, It was argued that, if a small increase of chromium in solution in austenite caused a sharp lowering of the M, point, it might lead to an explanation of occasional unsolved stress cracking of SAE 52100 during heat treatment. Commercial hardening is carried out at temperatures of incomplete solution, leaving carbides available to enrich the austenite during any inadvertent increase in temperature, such enrichment of the austenite in chromium content would lower the M, point nearer room temperature where cracking is more likely to occur. According, it was decided to investigate the effect of chromium, in quantities between o and 2 pet, on the M, point of commercial steels. Fig I summarizes the data available on chromium steels. For purposes of comparison, the M, temperature values were corrected by means of the Grange and Stewart formulas to (I) Hypoeutectoid compositions: 0.50 pct carbon and 0.80 pct manganese (z) Hsereutectoid compos-sition&apos;: 1." pet carbon and O.35 pct manganese. Only the steels having compositions reasonably close to these corrected values were included, because large adjustments inevitably introduce increased error such as are experienced in using the formula. The straight lines of Fig I were drawn by the authors. These data obviously do not settle the question Of the effect Of chromium On the Md Oint, particularly at low chromium contents. While it is fairly well established that chromium causes the M, to be lowered when present in quantities of I pet Or more, Grange and Stewart1 have suggested that in small amounts (less than 1 pet) it is more effective in lowering the Ma point, while Klier and Troiano2 have suggested that in small amounts it is less effective in lowering the Ma point. Payson and Savage3 concur with Klier and Troiano and further suggest that the effect is not linear at these concentrations. Rose and Fischer4 report that small amounts of chromium actually raise the Ma point of a 0.20 carbon steel. Material Two series of 35 Ib induction heats were melted for this work, the analyses of which are given in Table I. One series was aimed at 0.50 pct carbon and 0.80 pct manganese with chromium additions in 0,25 pet increments from o to 1.5 pct with a single heat at 2.0 pct Cr. This series was considered necessary because the commercial heat treatment of SAE 52100 does not generally introduce more than about 0.60 pct carbon in solution in the austenite. The high

Jan 1, 1949

By James C. M. Li

The Petch relation between the flow stress and the gain size is derived from a consideration of gain boundary sources of dislocations without the need of dislocation Pile-ups. Three mechanisms for inierpreting the yield stress: the gain boundary strength, the unpinning of Frank-Read source near a grain boundary, and the generation of dislocations from the grain boundary are compared and the condition of their equivalence is shown. The effect of the average angle of misfit of pain boundaries is found to be sma11 and so is that of the average angle of misfit of subboundaries having impurities. The effect of impurities on the ledge density in the grain boundary is treated thermodynamically and a relatwn is proposed for the variation of Petch slope with impurity activity. The effect of temperature on the Petch slope is interpreted as due to the change of ledge structure in the grain boundary. It is indicated that the effect of annealing temperature may be more important than that of the test temperature and therefore should be studied. The effect of plastic strain on the Petch analysis is deduced from a work-hardening equation in which the generation of dislocations has first-order kinetics and the annihilation of dislocations has second-order kinetics. It is concluded that the Petch slope will decrease with plustic strain if the rate of annihilation of dislocations is sufficiently large. Critical experiments which may shed light on the mechanism for the Petch relation are suggested. THE relation between the yield or flow stress, 0, and the grain size, l, was first proposed by all&apos; and later studied more extensively by Petch and co-workers, who also proposed a similar relation for the fracture stress and deduced from these a grain-size effect of the ductile-brittle transition temperature. The microscopic mechanism used by all&apos; and petch2 involves a pile-up of dislocations of like sign generated from a Frank-Read source. The yielding or flow takes place when the pile-up exerts sufficient stress at the grain boundary so that the plastic deformation can propagate from one grain to another. If the average strength of the grain boundary is ai and the average length of the pileup is lp, the Petch slope, k, is given by" where p is the shear modulus, b the Burgers vector, and v the Poisson ratio. This slope will be independent of the grain size if l/lp is a constant. This is possible, since, if the Frank-Reed source is situated near the grain boundary, lp = 1, and if it is situated in the middle of the grain, Ip = 1/2. cottrell,12 also using the pile-up mechanism, proposed that the stress concentration at the grain boundary will initiate Frank-Read sources near the grain boundary and in this manner a Lüders band can propagate from one grain to another. Assuming that the average distance between the Frank-Read sources and the grain boundary is 1, and the unpinning stress of the Frank-Read sources is op, Cottrell obtained the following Petch slope: This slope will be independent of the grain size if ls is independent of the same, which is not as obvious as the condition, Ip = I for Eq. [2]. In addition to this assumption, the direct relation between the Petch slope k and the unpinning stress, up, was recently questioned by Johnsonon grounds that it is inconsistent with the following observations: the independence of k with temperature and strain rate, and the small k in columbium, which, like iron, has a sharp yield point. As pointed out by ohnson," the most important objection both to the Hall-Petch mechanism, in which the strength of the grain boundary plays the role in yielding, and to the Cottrell mechanism, in which the unpinning of Frank-Read sources plays the role in yielding, is the lack of direct observation of the pile-ups. The dislocation structure in deformed iron has been examined recently in the electron microsope.&apos;-&apos; Dislocations appear to be generated from grain boundaries or other interfaces; they form clusters and tangles within the grain at very early stages of deformation, even in the Lüders band, if the deformation is slow or at normal and elevated temperatures. Although it is still too early to interpret bulk properties from thin-film observations, it does seem worthwhile to look for a mechanism for the Petch relation which does not require dislocation pileup. SUBBOUNDARY SOURCES In order to show that a consideration of grain boundary sources can lead to the same Petch relation as does the consideration of the strength of the grain boundary, we shall first discuss the case of a simple tilt boundary whose elastic properties have been studied in detail.17 The strength of a partially

Jan 1, 1963

By Martin Mayers

IT has long been recognized that it would be highly desirable to be able to predict the temperatures at various points in a burning fuel bed and their variations with changes of the properties of the fuel and the rate of air supply. Experimental investigations of fuel-bed tempera-tures1-4 have not been lacking, but the absence of any theoretical back-ground has made it impossible to use the results of these tests as a basis for prediction, except in a very general way. A mathematical analysis5, based on a somewhat simplified theory of the distribution of heat in a, fuel bed, has recently been completed by the author. Even though numerical values of some of the coefficients are not. known, the calcula-tions result in some conclusions of general significance. Thus, for example, it appears that when the temperatures throughout the fuel bed can be calculated, the rate at which ignition of the fuel by underfeed action can be maintained can also be calculated. The uncertainty concerning the values of the coefficients referred to above is a serious limitation on the use of that method. The following paper presents a discussion of these coefficients and includes estimates of their values based on the data now available. A brief description of the theory on which the analysis is based, and some results of the calculations showing their degree of agreement with experimental results, are presented by way of introduction to the discussion of, the coefficients. For a more extended discussion of the theory, see the A.S.M.E. paper5.

Jan 1, 1937

By G. R. Love, M. L. Picklesimer

Aboue 950°C the Nb-Zr system consists of a completely miscible bcc solid solution, commonly called the phase. Between 950 and 600°C, and between 20 and 85 pct Nb, the phase deconlposes, after sunciently long times, into two bcc solid solutions. The pct Zr alloys are conveniently descibecl with T-T-T (time-temperature-transformation) curves having a nose at about 2 hr at 700°C. The reaction rate varies only slowly with zirconium content and negligibly with oxygen contanzination; it is speeded up by a factor of 10 to 15 by 90 pct cold ulork and slowed dou by n factor oj 10 to 30 by a two-hundrecljold increase in grain size. Nb-r alloys with compositions between 40 and 85 pct Nb have been the basis for the majority of commercially important superconducting materials. In part because of their commercial promise, more is known about these alloys than about most other high-field superconducting materials. At the same time, there is considerable disputed or incomplete metallurgical information. For example, although Rogers and tkins&apos; indicate a monotectoid reaction at approximately 600°C and a two-phase 01 + 0, field extending between 20 and 85 pct Nb and to a maximum of 95OGC, erhout&apos; has reported that this entire region would be a single homogeneous B were it not for oxygen contamination. Again, although it has been shown that relatively short-time heat treatments in the vicinity of 700CZ significantly improve the ability of short wire samples to carry high currents in high magnetic fields at 4.2K, these observations have never been fully correlated with the structural change or changes occurring during the anneal. We intend to investigate in detail the effect of metallurgical variables, including heat treatment, on the superconducting properties of hard superconductors. To verify that our experimental techniques are valid and to establish a relative standard against which other materials may be measured, we feel it advisable to know the behavior of the Nb-Zr alloys under a variety of processing conditions. As an initial step toward this goal, we have determined in detail the kinetics of the transformations in Nb-Zr alloys. EXPERIMENT A number of problems had to be solved before beginning any fruitful work on the reaction kinetics in this system. While solving some of these problems, either by chance or by design, small amounts of information were obtained about alloys containing 40, 50, 60, 65, 67, 70, and 75 pct Nb, bal. Zr. In addition, a large range of grain sizes and a range of temperatures considerably greater than the range indicated by Rogers and Atkins phase diagram were examined. We will, however, report in detail only the results obtained for the Nb + 33 pct Zr and Nb + 25 pct Zr alloys at three grain sizes, two levels of oxygen contamination, and the temperature range 550 to 950°C. These data are most complete, but the other data are sufficiently complete to indicate the kind and magnitude of the variation of the transformation kinetics outside this range. The first and most difficult problem encountered in this inquiry was one of sample homogeneity. When Nb-Zr alloys are arc- or electron-beam-melted on a cooled copper hearth, solidification is sufficiently slow that there is appreciable coring in the cast structure and a large variation of grain size across the button thickness. Both these factors significantly affect the apparent reaction rate in the system. A two-step solution to the problem was attempted; an arc-melting and drop-casting technique has been developed by conald that greatly reduces the as-cast grain size and virtually eliminates coring segregation. Ingots made in this way exhibited no detectable (3 pct maximum) zirconium segregation. Before it was evident just how good this technique was, we attempted to supplement it with rather long-time, high-temperature annealing of the cast ingots. This annealing was carried out in evacuated and sealed (seal-off pressures < 1.0 x 106 torr) quartz capsules lined with tantalum foil at 1400 to 1450 C for 8 to 72 hr. There were two principal effects of this treatment: the grain size increased to a fairly uniform 150 p, and the surface and all grain boundaries near the surface acquired a film of a second phase, tentatively identified as an oxide (possibly additionally contaminated with silicon). There was no evidence that this 1400 C treatment had affected the zirconium segregation. High-temperature annealing was subsequently used only for grain-size control, but anneals of longer than 4 hr at temperatures greater than 1000°C were performed in dynamic vacuums (pressure no greater than 1.0 x lo torr). Any contamination resulting from these treatments was well below the limits of detection of our techniques. All samples, as cast, were cold-swaged to at least 85 pct reduction in area. The samples called cold-worked were tested as swaged. The minimum re-crystallization anneal for these alloys was about 12 hr at 1050 C; this produced an equiaxed grain diameter of about 4 to 8 P. Annealing for 4 hr at 1450°C produced a grain size of about 80 to 150 p; and annealing for 4 hr at 1650aC, close to the melting point of many of these alloys, produced a grain size of 0.5 to 1.0 mm. At all temperatures, the larger grain size was

Jan 1, 1967

By A. P. Watt

Foreword...............................................................323 Location of District..................................................... 324 Geology and Mining..................................................... 325 Topography and Climate................................................. 325 Lcad Production of the District...........................................325 Operating Companies in Southeast Missouri................................ 327 History of the District................................................... 329 Present Method of Treating the Ore....................................... 335 Character of Ore Treated...........................................338 Chemical Analyses............................................. 339 Description of Polished Specimens.................................340 The Concentration Problem of the District............................. 341 Handpicking at Mine La Motte....................................... 343 Crushing............................................................344 Roll Practice in the District.......................................... 346 Screening Practice................................................... 347 Jigging the Ore..................................................... 347 Bull Jigging.................................................... 348 Hancock-jig Practice............................................ 348 Classification of the Ores.............................................. 350 Table Treatment....:............................................... 352 Regrinding of Middling.............................................. 354 Description of Marathon Mill..................................... 358 Results of Preliminary Tests.....................................359 Rod Wear in the Marathon Mill.................................. 367 Steel Consumption.............................................. 368 Design of Marathon Mills.............. :......................... 368 Treatment of Table Middling........................................ 368 Slime Concentration................................................. 370 Methods Used in the Past.......................................370 Present Methods of Treatment................................... 371 Flotation of Slime.......................;........................ 371

Jan 1, 1918

By W. R. Crane

THE effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. There is no doubt but that in time, because of failure of pillars, extensive fracturing and widespread settlement of the surface will result, particularly along the slope of Red Mountain, where mining has been under way for many years. Were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Until development openings and surface plants are transferred to Shades Valley, protection of the surface will probably not be considered imperative, as the area involved is not of particular value for agricultural or building purposes. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. The occurrence of heavy beds of strong tough materials at varying distances above the orebed make it doubtful whether any serious disturbance of the surface will be experienced at any considerable distance from the outcrop, although some settlement will probably take place. It is certain, however, that no great volume of water will enter the mines from fracturing of the Fort Payne chert bed, as this is known to be a compact and practically impervious formation beyond the leached zone. Not so much can be said, however, regarding other possible sources of water, as pervious beds and through faults that may be encountered in future mining operations.

Jan 8, 1925

• The Venezuelan Trade Mission to the United States announced that Bethlehem Steel Corp. will begin exporting iron ore from its El Pao concession, south of the Orinoco River in Venezuela, in about three months. The ore will be transported by rail from the mines to barges on the Orinoco and transshipped to ore vessels at the coast for shipment to the Sparrows Point, Md., plant. The Latin American business men warned that projected increases in the United States tariff on petroleum imports from Venezuela would force that country into bilateral trade agreements with other countries and would mean drastic curtailment of Venezuelan imports from this country. •Bethlehem, South American Gold and Platinum Co., and U. S. Steel are investigating the possibilities of securing American foodstuff for their South American mining camp commissaries through the International Basic Economy Corp. IBEC buys in quantity to supply its subsidiary companies operating in Venezuela and Brazil. The mining companies will rid themselves of this burdensome task as well as realizing a saving from the bulk purchases of IBEC. •Oliver Iron Mining Co. has begun construction of a fine ore and taconite agglomeration plant at Virginia, Minn. It is expected to be ready in six months. The plant will be used to experiment with the making of clinker cakes and egg-sized lumps by sintering machines and nodulizing kilns respectively; about 1 million tons per year will be produced. • Roof pinning has been adopted at the iron mines of TCI, near Birmingham, to support overlying strata as mining progresses. Favorable results have been obtained in that dilution of the ore has been reduced by 50% which is attributable to this method of supporting the roof. •An American mining engineering team has gone to Turkey for a two-year assignment assisting Turkish government agencies in the $45 million ECA development, mechanization, and construction of cleaning plants for the Zonguldak coal field, 200 miles east of Istanbul on the Black Sea. The group consists of James Beeley, John E. Good, John S. Lambright, David Renshaw, and Charles R. Weir, all of the Paul Weir Co. •Arthur F. Taggart describes a new way of training engineers by emphasis on broad, basic engineering courses on page 460 of this issue. •Lawrence T. Tierney, chairman of the National Bituminous Coal Advisory Council, released a report stating that the increase in oil imports since the latter part of 194$ has caused significant damage to the U. S. fuel economy. It has reduced the strength of and employment opportunities in the coal, domestic petroleum, and transportation industries, as well as in related service and supplier fields. •Women, camels, and donkeys are the beasts of burden of the Sahara, according-to the UNESCO World Review. •Increased demand for magnesium sheet in airplane construction ana other phases of the national security program have led Alcoa to establish a sheet magnesium rolling division at its New Kensington, Pa., works which will begin operation shortly. Novel prospecting methods being used by the USGS in its search for uranium include: shock-mounted instruments in light trucks,. Geiger-counter probes lowered into augur holes, and experimental airborne prospecting.

Jan 4, 1950

By A. Sutulov

The segregation process, an alternative to benefi-ciation of oxidized and mixed sulfide-oxide copper ores, is studied here with particular emphasis placed on time, temperature, and coke and salt percentage factors. The results show that in a segregated charge, the copper assay of the coarsest fractions normally is of the same order as the copper assay of the tails obtained from grinding and flotation of the same charge. This observation suggests the possibility of limiting or even eliminating the grinding step from the flowsheet of a segregation plant. The segregation process, which offers an alternative to beneficiation of oxidized and mixed sulfide-oxide copper ores, was discovered in 1923 by Moulden and Taplin1,2 who were attempting to apply the Perkins process3&apos;4 to a Chilean ore from the Sagasca mine. After a number of investigations and pilot plant tests,&apos;-&apos; the segregation process became a successful industrial operation.&apos;r9 The process aroused considerable interest in Chile because of the existance of large reserves of oxidized copper minerals which could not be treated by conventional hydrometallurgical methods because of the high consumption and prohibitive cost of sulfuric acid. During the last two years, the Mineral Dressing Dept. of the Institute de Investigaciones Tecnology cas of University of concepci6n (Chile) has carried out a test program on 23 different ore samples representative of the national territory. These tests were carried out on a semi-continuous and batch scale with a rotary, automatically controlled and gas-fired furnace (supplied by Bartlett and Snow, Fig. 1). The results of these tests indicate that out of the 23 samples 20 can be successfully treated by this process with recoveries of copper ranging from 85 to 95%.10,11 The purpose of this paper is to treat some specific problems related to the segregation process. TIME AND TEMPERATURE FACTORS Time and temperature of calcination play an important role in the segregation process. When moderate salt and coke conditions were maintained (each of reagents was added in the quantity of 1 — % wt), systematic testing easily demonstrated the influence of these two factors on segregation and flotation recovery. The pertinent results are summarized in Fig. 2. To determine what specific changes the segregation process made on the ore, the samples, segregated at 700°C for different periods of time and under standard conditions, were granulometrically analysed and

Jan 1, 1963

By E. A. Nesbitt

THE important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent- magnet properties. In recent years great, advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,l an alloy of iron, cobalt, and molybdenum, the various iron- nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be .rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat- treatment, and at this time the ductility A of the alloy disappears. If the cast alloy is heat-treated without cold-working the magnetic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X l06. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold- worked in such a manner as to improve its energy product substantially, it is called Vicalloy II. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone In a variety of forms Vicalloy I or II is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age- hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of com- position are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. PREPARATION AND PROPERTIES OF VICALLY I The alloys were usually cast in graphite molds into bars ¾ in. in diameter and

Jan 1, 1946

By K. L. Woodruff

The first step in processing municipal solid waste (MSW), principally household waste, for resource recovery is usually shredding. A trommel has been investigated as a step to precede shredding. This way abrasive inorganic materials, such as stones and metals, would be removed prior to shredding, thus lowering the amount of feed and hence maintenance on the shredder. In addition, friable materials such as glass would be removed in large pieces, rather than pulverized too mall to process for recovery. The utility of a trommel for these purposes was investigated on a pilot scale using a unit 9 ft diam by 10 ft long with 4-in. square clear openings. Experimental results indicate that up to approximately half of the MSW may be removed as -4-in. material prior to shredding. The -4-in. fraction contains approximately 70% of the metals and 95% of the glass present in the MSW feed to the unit. Scale-up and cost information necessary for the design of a 60 to 70 tph unit is developed.

Jan 1, 1977

By M. Kaufman, A. E. Palty

The phase structure and aging characteristics of two nickel-base alloys, Inconel 718 and 702, were investigated. Wrought and cast Inconel 718 showed ArisCb as the major hardening phase, as well as ture was positively identified. Inconel 702 had Ni3Al as the major hardening phase, as well as Cr7C3-of the phase amounts with temperature was determined. 1 HE value of phase structure and aging rate information in the utilization of alloys has been well established. As part of a continuing program, the results obtained on two nickel-base alloys, hconel 718 and Inconel 702, are presented here. Inconel 718 is a relatively new alloy considered for application in both sheet and cast form. Its novelty lies in the use of high columbium tantalum levels in a Ni-Cr-Fe base. No previous work on this type of alloy has been reported in the literature. Inconel 702 is being used now as an oxidation-resistant sheet alloy. Occasional fabrication problems spurred work on its basic structural behavior. The composition of 702 is essentially nichrome plus aluminum and titanium for strengthening and added oxidation resistance. This puts it in the basic class of other nickel-base alloys which have already been studied. The two alloys will be treated separately. INCONEL 718 Phase Study Methods. The phases present after the various conditions investigated were determined by X-ray diffraction analysis of two different elec-trolytically extracted residues and microscopic examination. The extraction methods, using 10 pct HC1 in alcohol and 10 pct H3PO, in water and the X-ray technique have been described previously.&apos; The effect of temperature on the phase behavior was studied on sheet material using the following heat treatments: 2250°F, 2 hr, ice brine quench 1300 100 hr, water quench 2250°F, 2 hr, ice brine quench 1400°, 100 hr, water quench 2250°F, 2 hr, ice brine quench 1500°F, 100 hr, water quench 2250o 2 hr, ice brine quench 1700°F, 48 hr, water quench 2250°F, 2 hr, ice brine quench 1850°, 24 hr, water quench 2250°, 2 hr, ice brine quench 2000°F, 6 hr, water quench The high solution temperature was an attempt to dissolve as many phases as possible without causing melting. Aging exposures were made longer than normal heat treating times in order to approach equilibrium conditions more closely. Cast material was examined only in the as-cast condition and with the normal heat treatment (1700°F, 1 hr, air cool 1325oF, 16 hr,air cool). Materials. The full phase study was performed on sheet specimens approximately 1/2 in. by 2 in. by 1/16 in. The cast pieces were cut from the gating system of a vacuum-cast test piece. An all weld-metal specimen was made by running many weld beads on the sheet using filler made from the sheared edges of the sheet. All external contamination was removed by belt-sanding followed by an electro-polishing treatment. The typical composition of wrought Inco 718 is as follows: The alloy is air-melted. Cast hco 718 may have higher molybdenum. Due to the expectation of finding a Ni-Cb phase (Ni, Cb) for which no X-ray diffraction pattern was available in the ASTM Index, a special 5 Ib heat to the stoichiometric composition of this intermetallic

Jan 1, 1962

J. R. Lane (Metals Research Laboratory, Washington)—A new type of deformation called "kinking" has recently been described. Is there any relation between the "rumpling" described in this paper and "kinking?" D. C. Jillson (author&apos;s reply)—Both are manifestations of bending about [210] axis. The difference is one of degree. W. C. Ellis (Bell Telephone Laboratories, New York) —Some observations of deformation in zinc recorded in this paper may be applicable generally to flow in metals. One of these, deformation in torsion without evidence of slip or twinning in the early stages and with startling ease, when the twist is about the hexagonal axis, adds another method of flow to the presently increasing list of mechanisms. This illustrates again that a crystal will utilize any realizable process to flow and relieve stress. The process is not necessarily classical directional slip—& this case, it is rotational slip. The question naturally occurs: Will face-centered cubic metas stressed by twisting about an octahedral axis flow in a similar manner by rotation on an octahedral plane? I would like to ask Dr. Jillson if he has made any experiments or knows of any experiments of this type on face-centered cubic metals? Face-centered cubic metals possibly would behave differently from zinc, since, for one thing, the stacking sequence is different for the two structures. The results of such experiments, however, would be instructive in providing more information about deformation processes. D. C. Jillson—Dr. Roy E. Swift, working in the Hammond Laboratory at Yale, performed a twist test on a single crystal of brass. The work has not been published, and I do not know the crystallographic direction of the axis of the specimen used. Lo-ching Chang (Columbia University, New York)— Observations similar to Figs. 1 and 2 of the paper were obtained by us during the bending and unbending of an orthorhombic Au-Cd alloy.&apos;l This orthorhombic alloy is the product of diffusionless transformation from a single crystal of p Au-Cd alloy (CsC1 structure) containing 47.5 atomic pct Cd on cooling to about 60 "C.62 Referring to the effects of annealing, has the author tried any loilg time high temperature anneal, such as 150 to 200 hr at 40O°C? D. C. Jillson—No. C. Crussard (Ecole des Mines, Paris: France)—I

Jan 1, 1952