Search Documents

By N. J. Grant, B. C. Giessen, R. Koch

The system Nh-Ir was investigated over the complete concentration range by metallography and X-my techniques, using forty one alloys. The solubility limits of terminal and intermediate phases and the solidus temperatures were determined. Five intermediate phases were found: a Nb3Ir, cubic, Cr3O type; tetragonal, ofecr thorhomhic, isostruc-turn1 with (ta-Rh); and a Nhlr3. cubic, AuCu, type. a Nb3lr and a Nbfr3 melt congruently; three eutectic and three pentectic reactions occur. The phase diagram of the Nb-Ir system had not been fully treated in the literature; only surveys of intermediate phases were found.1"5 In this study, the details of the phase boundaries were investigated as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS The experimental procedures such as arc melting of powder compacts, heat treatments, solidus measurements, X-ray, and metallographic observation were identical with those used in the work on the Nb-Rh phase diagram.&apos; They will therefore not be repeated here except where the conditions differed. The purity of the niobium powder was as stated in Ref. 6; the iridium powder of 99.9+ pct purity from J. Bishop and Co., Malvern, Penn., did not contain impurities exceeding 100 ppm, except rhodium (200 ppm). The melting points and vapor pressures of both elements are very similar. This fact contributed to a very small weight loss on melting and facilitated preparation of homogeneous alloys. As shown in Ref. 6 for Nb-Rh, no oxygen pick-up exceeding 200 ppm had to be considered; this was regarded as valid also for Nb-Ir. A total of forty one alloys were used in the determination of the phase diagram; their concentrations are shown in Fig. l, which presents the phase diagram. The concentration limits as determined by the weight-loss method averaged <0.2 at. pct, and never exceeded 0.5 at. pct. Heat treatments were carried out as described in Ref. 6. Depending on the concentration, only tantalum, tungsten, or iridium containers were employed, avoiding oxide crucibles altogether. Alloys from 0 to 25 and from 65 to 100 at. pct Ir were homogenized at 2095°C for 15 hr, intermediate compositions from 25 to 65 at. pct Ir for 65 hr at 1780°C. A typical annealing-time schedule is presented in Table I. Solidus points were measured as described in Ref. 6 with the modification that samples rich in niobium were held between pieces of tantalum foil and samples of high iridium concentrations were held between rhenium platelets or in iridium wire. After each run it was ascertained metallographically that no reaction with the holder had occurred. Rhenium was selected as holder material after it had been shown in separate tests that the melting points of Re-Ir alloys rise continuously from 2440°C. Metallographic examination was carried out as described in Ref. 6, and the same procedure and etchants were used successfully. While metallographic discrimination between a Nb3lr and o was easily possible, X-ray diffraction was necessary to separate al and ct2. X-ray powder patterns were taken and evaluated as for Nb-Rh6 yielding the error limits indicated in Table 111, to be introduced later. For the determination of the invariant reactions and phase boundaries, the same techniques as for Nb-Rh6 applied. The general accuracy of invariant concentrations is regarded as somewhat higher than for Nb-Rh due to the small slope of most solvus lines.

Jan 1, 1964

By Jim F. Lemons

INTRODUCTION A nickel doesn&apos;t buy much anymore. That&apos;s even true in the cost of recovering nickel -- the commodity. A 5[C] per pound (11 [c] per kilogram) increase in the nickel price won&apos;t cover a 10-percent increase in fuel costs for processing laterite ores, nor will it cover a 10- percent increase in wages for recovering nickel from a sulphide ore. It won&apos;t even cover a 5- percent increase in the capital cost necessary to mine and process ocean nodules. The basis for this statement and a quantitative analysis of the variations in costs to recover nickel from different types of nickel ores will be discussed in this paper. During the early part of the 1970&apos;s, the interest in nickel and its potential development was shifting from Canada to the Pacific Basin area. Canadian growth rate was slowing and each additional increase in nickel capacity was very expensive (Argall, G.O., 1970). Laterite ores were attractive to developers since they were easy to mine at a low labor cost, and technologies were being developed that would allow the recovery of nickel in marketable forms (Mohide, T.P., Warden, C.L., Mason, J.D., 1977). During the last decade, new laterite production was achieved in the Philippines and Botswana, and a significant increase in production from Indonesia and New Caledonia occurred. However, recent reports on nickel identify numerous problems plaguing the industry, i.e., high energy costs that are forcing shutdowns (INCO, 1980), (Mohide, T.P., Warden, C.L., Mason, J.D., 1977), high Canadian sulphide mining labor costs (Anon., 1976), and rapid inflation of nickel capital costs (Anon., 1981b). No definitive study has been made to determine how sensitive the total cost of production is to rising energy, labor, or capital costs, or to identify to what extent increased byproduct revenues could be used to offset these production costs. The purpose of this paper is to quantify the effects of increases in energy, labor, capital costs, and by-product credits on the future cost of production from nickel reserves and/or resources. METHODOLOGY OF ANALYSIS In order to evaluate the sensitivity of nickel production costs to changes in energy, labor, and capital costs, and in byproduct revenues, an analysis was made of existing and proposed nickel operations, their costs, and their sensitivity to change. The data for these analyses were obtained from numerous sources including international govern¬ment and university publications, professional journals, company reports, private communications, U.S. Bureau of Mines contracts, and estimates by Bureau of Mines personnel. These data were collected, in part, as an ongoing effort of the U.S. Bureau of Mines Minerals Availability System (MAS) to systematically measure and classify identified mineral resources according to their respective extraction technologies, economics, and commercial availability. The MAS Program is currently evaluating the present and potential availability of nickel to the United States in relation to mining, beneficiation, smelting, refining, leaching, transportation, infrastructure, environment, land use, labor, productivity, technology efficiencies, operating capacities, deposit life, and political factors. As a summary of this data, the following briefly describes nickel ore types as each relates to energy, labor, capital, and byproducts. Sulphide Operations Nickel is currently available from sulphide deposits. Roughly 55 percent of the current world nickel production in market economy countries is from sulphide ores, although only about 20 percent of the known land-based nickel reserves and/or resources are sulphides (INCO, 1981). In 1979, the Western World sulphide reserves were estimated at about 9.2 million metric tons of nickel (Little, A.D., 1979). Sulphide ores are typically mined underground, thus resulting in high mining costs; however, these ores can often be upgraded by flotation prior to final nickel recovery and require about one-third of the energy required to recover nickel from laterites (Anon., 1981c). In addition, nickel in sulphide ores may be associated with economically recoverable byproducts, which include copper, cobalt, gold, silver, and other precious metals. Laterite Operations Forty-five percent of current nickel production is from laterite deposits. Laterite deposits account for 80 percent of the known land-based nickel reserves and/or resources (INCO, 1981). In 1979, the Western World laterite reserves were estimated at over 35 million metric tons of nickel (Little, A.D., 1979). Nickeliferrous laterites are residual soils formed by weathering, typically under tropical or near tropical conditions. They can be easily mined by open-cut methods, but generally cannot be beneficiated; thus, recovery of nickel must entail processing of the total mined ore. Usually, these ores have high moisture content (20 to 30 percent by weight) that result in additional fuel costs to dry the ore. Nickel silicates, garnierites, are, processed by pyrometallurgical methods; limonite nickel oxides are normally leached. Byproduct cobalt is not recovered from most ferronickel operations, and is only recovered to a limited extent from many leach operations.

Jan 1, 1982

By D. L. Rainey, E. R. Goter, W. R. Hudspeth

THE area in which spodumene-bearing pegmatites occur extends from Gaffney, S. C., in a northerly direction to Lincolnton, N. C., a distance of about 16 miles. The zone averages 2 miles in width. Interest in this area was first aroused by the discovery of small amounts of cassiterite in the peg-matites and in greissen which occurs on the walls of some of the pegmatites. Attempts were made from 1880 into the 1920&apos;s to mine and concentrate cas-siterite, but there were no successful operations. In 1935 L. M. Williams became interested in the area and began prospecting by trenching and sinking several small shafts. He gradually gained control of a considerable acreage south of the city of Kings Mountain, N. C. Mr. Williams states that he produced some ore from a shaft which he shipped to the Maywood Chemical Co. in the late 1930&apos;s. In 1937 G. H. Chambers of the Foote Mineral Co. visited the area and examined several properties, but the lithium market was too small to support the necessary concentrating plant. Early in World War II the Solvay Process Co., encouraged by various federal agencies, acquired the Williams properties and leases and started a drilling program to develop reserves for spodumene mining. A study of this area was also made under T. L. Kesler by the U. S. Department of the Interior Geological Survey. Starting in 1942 a concentrating plant, water supply dams, and shops and other buildings were constructed. The Superior Stone Co., a neighboring crushed stone operator, was awarded a contract to mine and crush the pegmatite ore. Late in 1943 the plant started operations, which were continued until February 1946. A drop in demand for lithium chemicals forced it to close and remain closed for several years. In 1948 the Foote Mineral Co. became interested in assuring itself a source of lithium ore on the North American continent, to be used in the production of lithium ore chemicals, and inspected properties in Canada, South Dakota, and North Carolina. The North Carolina deposits were the most promising. In the fall of 1950 the company leased the Solvay interests with option to buy and acquired additional properties. Renovation of the mill and preparation of the quarry for mining was begun in earnest in January 1951. A new crushing plant was built and construction started in July 1951. The flotation process used was developed in the North Carolina State Minerals Research Laboratory located at Asheville, N. C. Foote is now in the process of expanding its production. The crushing plant is being revamped and much of the old milling equipment purchased from Solvay will be replaced by new. Mining equipment of suitable capacity has been received and is in use. The frontispiece is a general view of the mill. The orebodies consist of pegmatite dikes composed of fine-grained albite and quartz, with varying amounts of mica and spodumene. The latter may amount to as much as 50 pct of the rock, but the overall average is about 15 to 20 pct. Tin, columbite-tantalite, beryl, and other valuable minerals are present in varying small amounts. These dikes, which intruded into the Roan Gneiss underlying most of the Piedmont area, strike approximately N 30 E and dip about 85" to the west. The gneiss has the same strike but dips about 70" west. The dikes lie in a belt extending from Lin-colnton, N. C., to Gaffney, S. C., and passing through

Jan 1, 1954

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B POTTER 1888 RICHARD PEARCE 1889

Jan 1, 1923

By H. B. Probst

Mechanical twins were produced in zone-refined tungsten single crystals by explosive working at room temperature. These twins are parallel to (112) planes and have irregular boundaries rather than the classical plane twin boundaries. These boundaries aye grooved surfaces in which the grooves themselves are parallel to a <111> direction and the sides of the grooves appear to be par-allel to (110) planes. TWINS were produced in tungsten single crystals by explosive working at room temperature. These twins differ in character from any previously reported for tungsten; however, they are similar to those found in molybdenum after compression at -196°C.1 Deformation twins "resembling Neumann bands in ingot iron" have been observed in tungsten by Bech-told and Shewmon.2 This observation was made with sintered polycrystalline tungsten pulled in tension to fracture at 100°C and using a strain rate of 2.8 x 10-4 sec-1. More recently Schadler3 found deformation twins in zone-refined tungsten single crystals pulled in tension at -196"&apos; and -253°C. These tests were conducted using a strain rate of 3.3 x l0-4 sec-1, and the twin bands were found to be parallel to a (112) plane. Deformation twins in tungsten&apos;s sister metal, molybdenum, were observed by Cahn.4 These twins were produced by compressing small (0.7 mm) vapor-deproducedposited molybdenum single crystals at -183°C. The compression was performed &apos;by impact." By the use of precession X-ray techniques, Cahn was able to identify the twin plane as {112} and the shear direction as <1ll>. Mueller and Parker1 produced deformation twins in polycrystalline electron-beam-melted molybdenum by compression at -196°C. Their "loading rate" was 5000 psi per min which, judging from their stress-strain curve, corresponds to a strain rate of approximately 0.3 x 10-4 sec-1. These twin bands were found to be parallel to (1 12) planes; however, they differed in appearance from previously observed twins. In place of straight and parallel twin boundaries they were found to be irregular, jagged, and sawtoothed. The sides of the saw teeth were identified as (110) planes and irrational planes of a (111) zone. The twins observed in the present work in tungsten single crystals are similar in appearance to those of Mueller and Parker in polycrystalline molybdenum. The starting material used in this investigation was 3/16-in. diam commercial tungsten rod produced by powder-metallurgy techniques. This material was converted to a single crystal by the electron-bombardment floating-zone technique.= The process was carried out in a vacuum of 10-5 mm of Hg using a traversing speed of 4 mm per min. Segments (=2 in. long and 3/16 in. in diam) of two crystals (A and B) produced in this manner were studied. Crystal A received one zoning pass, while crystal B received two passes. The two crystals were explosively worked at Bat-telle Memorial Institute in the following manner. A 1/2-in.-thick layer of plastic was applied to the crystals to serve as a buffer in an attempt to prevent cracking. The composite, crystal and buffer, was then wrapped with 1/8-in.-thick DuPont sheet explosive EL506A2 and detonated in water at room temperature. Metallographic samples of the worked crystals were prepared, and back-reflection Laue X-ray patterns were obtained using unfiltered molybdenum radiation. RESULTS AND DISCUSSION Blasting the crystals as described above failed to prevent cracking. The crystals fractured into several fragments about 3/16 to 1/2 in. long; however, the fragments were of sufficient size to be useful for the subsequent study. The diamond pyramid hardness of the crystals after blasting was in the range 430 to 450 as compared with 340 for the as-melted material, which shows a definite hardening resulting from plastic deformation. These hardness values were obtained using a 1000-g load and taking readings only in sound portions of the crystals free of cracks. The crystals exhibited profuse twinning as shown in Fig. 1. No such structure is present in the as-melted condition. Most of these twins have jagged twin boundaries and are similar in appearance to those found in molybdenum by Mueller and Parker. The twins in both crystals were found to be parallel to {112} planes. This identification was made by using the conventional two-trace method. Subsequent efforts to describe these twins more fully were carried out on crystal A. If the longitudinal axis of crystal A is placed in the (001)-(011)-(Il l) basic triangle of the standard cubic stereographic projection, as in Fig. 2, then the two sets of twins shown in Fig. 1 are parallel to the (112) and (121) planes. Fig. 3 shows a schematic representation of a twin with jagged boundaries. This type of twin with a <111>

Jan 1, 1962

By Richard J. Borg

The vapor pressure of Cd in equilibrium with CdSb in the presence of excess Sb has been measured using the Knudsen effusion method over the temperature range 276° to 379°C. The free energy of formation of CdSb is given by AF° = -1.58 + 1.53 x l0-4 T, kcal per mole. The enthalpy and entropy are obtained from the temperature coefficient of the .free energy. CADMIUM and antimony have almost imperceptible mutual solid solubility but form a single stable intermediate phase, CdSb. This phase, according to Han-sen,l extends from about 49.5 at. pct to 50 at. pct Cd at 300°C and has the orthorhombic structure. The free energy of formation of CdSb can be calculated from the vapor pressure of Cd for compositions which contain less than 49 at. pct Cd. The appropriate reaction and formulae are given by Eqs. [I] and [2]- CdSb(s, ~ Cd(g)-, +Sb(s) [1] Since Sb is in its standard state, Af - N,,AF&apos;-,, = NcdRT In a,, = NcdRT InP/PO [2] In Eq. [2], P, is the vapor pressure of Cd in equilibrium with the alloy, and Po is the vapor pressure in equilibrium with pure solid Cd. It is implicit in this calculation that the free energy only slightly changes within the narrow limits of the single phase field. Thus, the value obtained from the antimony-rich boundary is truly representative of the stoi-chiometric compound. The results reported herein are obtained from a mixture near the eutectic composition, i.e. 59 at. pct Sb. Only two previous investigations" of the free energy of formation of CdSb have been made. Both relied upon the electromotive force method, and measurements were made over relatively narrow temperature ranges which strongly influences the reliability of the values of AH and aS. EXPERIMENTAL The eutectic composition is prepared by fusing reagent grade Cd and Sb by induction heating in vacuo with the starting materials held in a graphite crucible having a threaded lid. The material obtained from the initial melt is pulverized, sealed under high vacuum in a pyrex capsule, and annealed at 420°C for two weeks. X-ray analysis"gives the following lattize parameters: a = 6.436A, b = 8.230& and c = 8.498A using Cu Ka radiation with A = 1.54056. These values are in fair agreement with the result? previously reported by Al~in:4 i.e. a = 6.471A, b = 8.253A, and c = 8.526A. Vapor pressures are measured using an apparatus which has been described elsewhere,= however, with a single important modification. Knudsen effusion cells are made of pyrex with knife-edged orifices made by grinding the convex surface of the lid on #600 emery paper. Photographs taken at known magnifications using a Leitz metallograph enable the determination of the orifice area. Numerous calibration measurements of the vapor pressure of pure Cd give close agreement with values previously reported5,= thus indicating that no significant error can be ascribed to the substitution of glass cells for metal cells used in previous work. Because the vapor pressure of Cd is reliably established and because it is difficult to obtain Clausing factors for the glass cells, the final values used for the orifice areas are calculated from the calibration measurements of the vapor pressure of pure Cd. Effusion runs are started in an atmosphere of purified helium which is quickly evacuated as soon as the cell attains thermal equilibrium. Less than one minute is necessary to obtain high vacuum after evacuation begins, and the temperature seldom varies by more than 0.5oC from the value obtained prior to pumping out the helium. RESULTS The results of this investigation along with other pertinent data are tabulated in Table I. Fig. 2 is the familiar graph of log P against T-10 K. At least mean squares analysis of the data presented in Table I yields the following equation: log1DJP = 8.790 - 6472 x T"1 [3] The deviations of the individual measurements from the values calculated with Eq. 131 are given in column six of Table I; the average deviation is 4.0% of the calculated value. Although the partial molal properties change significantly with composition within the single phase region, the integral thermodynamic value should remain relatively constant. Hence the results of the following calculations, which use the data obtained for the eutectic composition, are probably representative of the equi-atomic compound. Eq. [4] describes the vapor pressure of pure Cd as a function of temperature and may be combined with Eq. [3] to

Jan 1, 1962

NEW MEMBERS The following list comprises the names of those persons who became members during the period of July 10, 1917, to Aug. 10, 1917. ARNOT, STANLEY L., Engr., Plymouth Cons. Gold Mines; Ltd., Plymouth, Amador Co .2 Cal. BARRETT, LESLIE PARK, Asst. Geol.... Michigan Geological Survey, Lansing, Mich. BENNIE, JOHN WILLIS Gen&apos;l. Mgr., Shannon Copper Co., Clifton, Ariz. BRINTON, OWEN FUGATE Mgr., Admiralty Zinc Co., Quapaw, Okla. BRODERMANN, JORGE, Civil Engr., Compania Minera San Francisco, Havana,Cuba. BROWN, RICHARD HENRY JR., Sales Engr., Ingersoll Rand Co., 300 N. Broadway, St. Louis, Mo. BROWN, STANLEY Chile Exploration Co., Chuquicamata, Chile. BUDDECKE, WILLIAM A Pres., Point Milling & Mfg., Co. Mineral Point, Mo. BURGESS, GEORGE K., Physicist and Chief, Division of Metallurgy, Bureau of Standards, Washington, D. C.

Jan 9, 1917

By William E. Ford, Edward Salisbury Dana

Normal phosphoric acid is H3P04, and consequently normal phosphates have the formulas R3PO4, R3(P04)2 and RPO4, and similarly for the arsenates, etc. Only a comparatively small number of species conform to this simple formula. Most species contain more than one metallic element, and in the prominent Apatite Group the radical (CaF), (CaCI) or (PbCI) enters; in in the Wagnerite Group we have similarly (RF) or (ROH).

Jan 1, 1922

By R. F. Miller, R. F. Campbell

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942

By R. F. Campbell, R. F. Miller

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942

By C. A. Heberlein

C. A. HEBERLEIN, New York, N. Y.-The results stated by Rey and Brevers are so startling that they are of great interest, as the concentration of a low percentage of cinnabar by differential flotation yields a high-grade concentrate in the presence of either arsenical or iron pyrite. The authors say: "Cyanide can thus be used to depress arsenopyrite and make a good cinnabar-arsenopyrite separation. A cinnabar-pyrite separation could probably be effected in the same way." Corrosive sublimate at the present price of mercury would be a very expensive reagent but the expense would be justifiable if a high rate of concentration could be obtained with a high extraction. On my request, special tests were made in the Punitaqui mill in Chile along the line suggested by the authors, without any improvement of either grade or extraction. As the recovery of the cinnabar in a complex sulphide of chalcopyrite and pyrite gave unsatisfactory results, I had tests made at the testing laboratory of the American Cyanamid Co. at Stamford, Conn. As these tests turned out to be highly satisfactory, not only at Stamford but later at the mine, they are presented here. [ ] The pulp had a density of 22 and a pH of 7.8. Total time of conditioning was one minute. The reagent added was Texas fuel oil, 0.116lb. of 33.7 Bé. gravity containing 0.9 per cent sulphur. Frother, 0.062 lb. of No. 5 pine oil. Rate of concentration of mercury was 25.7: 11. [ ]

Jan 1, 1941

Jan 1, 1969

By P. P. Gregory

The rate of drilling operations in the West Texas district during 1940 was approximately equal to that of 1939. The total number of wells dillled in the area during the year was 1834, of which 1716 were completed as oil producers, 12 were gas wells and 106 were dry holes. The number of wildcat wells drilled during the year was comparatively small. The drilling of inside locations in proven areas and the drilling of wells for the purpose of extending the productive limits in producing fields constituted the bulk of development during 1940. Gaines County led all other counties in the district in the total number of oil-well completions. The oil production totaled 83,345,381 bbl., the highest figure for any year since proration was begun. The 1940 oil production exceeded the 1939 production by approximately four million barrels. Discoveries While comparatively few new oil-producing areas were discovered during 1940, it appears that the oil production found in simpson lime in the Abell field, pecos County, was an outstanding discovery for the year. This was the second Ordovician discovery in Pecos County. Taubert, McKee & Siemoneit located its discovery well, V. W. Crockett No. 1, set. 4 1/2 H. & T. C. R.R, co, survey in the Imperial area of northwestern Pecos County. The top of pay was encountered at 5270 ft., and the well was bottomed at 5357 ft. in simpson lime, on act. 17, I940. The initial production was 928 bbl. of 43" gravity sweet oil in 11 hr. 23 min., flowing naturally through 2-in. tubing with gas-oil ratio of 783 cu. ft. per barrel. Following the completion of the discovery well, large blocks of land were leased in the area, and several locations were made toward the close of the year. There is every indication that the Abell field will become a major producing field in the West Texas district. There was no pipe-line outlet for the field at the end of the year. Shipley-Silurian field, discovered by the Gulf Oil Corporation, appears to be another major addition to the oil reserves in 1940. The discovery well, Wristen Brothers No. 5, is in sec. 18, block 5, H. & T. C. R.R. Co. survey in Ward County. The well was drilled to a total depth of 9187 ft. and was plugged back to 7075 ft. The Silurian lime section was acidized with 3000 gal., from 6993 to 7075 ft., and on Dec. 5, 1940, the well was completed for initial production of 3040 bbl- of 32.2" gravity oil in 24 hr., flowing through tubing. Todd Deep field, Crockett County, was discovered by the Continental Oil Co. et al. The discovery well, J. S. Todd No. 2, set. 29, block WX1 G.C. & S.F. R.R. Co. survey, was completed on April 3, 1940. The top of pay was encountered at 5623 ft., and the well was bottomed at 5691 ft. for initial production of 1613 bbl. of 40.6&apos; gravity oil flowing naturally through 2-in. tubing. The pay section was found in Strawn lime of Pennsylvanian age. There were six producing wells in the field at the end of the year. This appears to be another major discovery in 1940. There was no pipe-line outlet in the field at the end of the

Jan 1, 1941

By P. P. Gregory

The rate of drilling operations in the West Texas district during 1940 was approximately equal to that of 1939. The total number of wells dillled in the area during the year was 1834, of which 1716 were completed as oil producers, 12 were gas wells and 106 were dry holes. The number of wildcat wells drilled during the year was comparatively small. The drilling of inside locations in proven areas and the drilling of wells for the purpose of extending the productive limits in producing fields constituted the bulk of development during 1940. Gaines County led all other counties in the district in the total number of oil-well completions. The oil production totaled 83,345,381 bbl., the highest figure for any year since proration was begun. The 1940 oil production exceeded the 1939 production by approximately four million barrels. Discoveries While comparatively few new oil-producing areas were discovered during 1940, it appears that the oil production found in simpson lime in the Abell field, pecos County, was an outstanding discovery for the year. This was the second Ordovician discovery in Pecos County. Taubert, McKee & Siemoneit located its discovery well, V. W. Crockett No. 1, set. 4 1/2 H. & T. C. R.R, co, survey in the Imperial area of northwestern Pecos County. The top of pay was encountered at 5270 ft., and the well was bottomed at 5357 ft. in simpson lime, on act. 17, I940. The initial production was 928 bbl. of 43" gravity sweet oil in 11 hr. 23 min., flowing naturally through 2-in. tubing with gas-oil ratio of 783 cu. ft. per barrel. Following the completion of the discovery well, large blocks of land were leased in the area, and several locations were made toward the close of the year. There is every indication that the Abell field will become a major producing field in the West Texas district. There was no pipe-line outlet for the field at the end of the year. Shipley-Silurian field, discovered by the Gulf Oil Corporation, appears to be another major addition to the oil reserves in 1940. The discovery well, Wristen Brothers No. 5, is in sec. 18, block 5, H. & T. C. R.R. Co. survey in Ward County. The well was drilled to a total depth of 9187 ft. and was plugged back to 7075 ft. The Silurian lime section was acidized with 3000 gal., from 6993 to 7075 ft., and on Dec. 5, 1940, the well was completed for initial production of 3040 bbl- of 32.2" gravity oil in 24 hr., flowing through tubing. Todd Deep field, Crockett County, was discovered by the Continental Oil Co. et al. The discovery well, J. S. Todd No. 2, set. 29, block WX1 G.C. & S.F. R.R. Co. survey, was completed on April 3, 1940. The top of pay was encountered at 5623 ft., and the well was bottomed at 5691 ft. for initial production of 1613 bbl. of 40.6&apos; gravity oil flowing naturally through 2-in. tubing. The pay section was found in Strawn lime of Pennsylvanian age. There were six producing wells in the field at the end of the year. This appears to be another major discovery in 1940. There was no pipe-line outlet in the field at the end of the

Jan 1, 1941

By J. R. Cahoon, H. W. Paxton

The possibility of using unidirectionally solidified, two-phase alloys as an approximation to fiber composite materials is investigated. The short-term me.chanical properties and failure modes of unidirectionully solidified A1 (rich)-Cu alloys containing ap -Proximately 0, 17.5, and 27.7 vol pct of 0 phase &apos;fibers" are determined at temperatures from 25" to 500" and compared with those obtained for conventionul SAP alloys. In a previous publication,&apos; hereafter referred to as I, the possibility of understanding some of the room-temperature mechanical properties of unidirectionally solidified castings was explored. For Al(rich)-Cu and Al(rich)-Mg two-phase alloys over a substantial range of compositions, the yield and ultimate strengths and common ductility measures were very adequately predicted from the principles of fiber strengthening4 and the analysis of ductility outlined by Gurland and Plateau." The results obtained in I suggest the possibility of using unidirectionally solidified, two-phase alloys to simulate fiber composite materials where the inter-dendritic second phase or constituent acts as the reinforcing material. Recent attempts concerning the fabrication of fiber conlposites have concentrated on producing composites with a good bond between fiber and matrix and with very long fibers so that their maximum contribution to the strength of the composite may be realized. However, these objectives are difficult to attain in practice and present fabrication processes are either extremely laborious or costly.13 The slow, unidirectional solidification of eutectics has received considerable attention as a method for producing composite materials. 5,6 This method can fulfill both of the above objectives but it is currently laborious, expensive, and has the additional disadvantage that the volume fraction of reinforcing phase cannot be easily varied. On the other hand, unidirectionally solidified, two-phase alloys, also with a good bond between the phases, are relatively easy to make and the volume fraction of reinforcing "fibers" can be easily varied by changing the average composition of the alloy. The disadvantage of the cast alloys is that the mechanical effectiveness of the "elongated interdendritic reinforcements" (EIR)* may be reduced due to their rela- tively short lengths, the w factor in Eq. [2] of I. However, if the EIR have a high strength their contribution can be considerable. For composite materials containing discontinuous cylindrical fibers of various lengths the ultimate strength is given by1 where it is assumed that the composite fractures when the fibers fail. In Eq. [I], a, is the stress in the matrix just prior to failure of the composite, Vf is the total volume fraction of fiber reinforcing constituent, Vf(l+) is the volume fraction of fibers whose lengths exceed the critical length, I,, which is defined as the shortest length of fiber in which the stress can build up sufficiently to break the fiber. af is the fracture strength of the fiber material, w is a factor accounting for the discontinuity of those fibers whose lengths exceed I,, 1-/d is the average aspect ratio of those fibers whose lengths are shorter than I,, and t is the shear stress in the matrix at the fiber-matrix interface. The factor w is dependent on the length of the fibers and also on whether deformation of the matrix occurs plastically or elastically. However, for a given length of fiber, w is smaller when elastic deformation of the matrix is assumed.&apos; It is of interest to consider the properties of simple unidirectionally solidified, two-phase alloys at elevated temperatures in view of the possibility of using suitable modifications for high temperature service. Knowledge of the creep behavior of these materials is still rudimentary (although under active investigation) and the present paper concerns itself with short time tensile properties of some alloys similar to those investigated in I (i.e., unidirectionally solidified Al(rich)-Cu alloys). Unidirectionally solidified alloys containing 5.6, 17, and 23 wt pct Cu were tested parallel to the direction of solidification at temperatures from 25" to 500°C. In the present investigation, the alloys were homogenized for 2 days at 535°C giving a matrix of homogeneous a phase (5.2 wt pct Cu) and an interdendritic constituent (EIR) which was completely Q phase (53 wt pct Cu). EXPERIMENTAL Alloys of nominal composition 5.6, 17, and 23 wt pct Cu (containing approximately 0, 17.5, and 27.7 vol pct 8 phase, respectively, after homogenization at 535°C) were prepared by melting 1200 g of A1 (99.99 pct) in a high purity graphite crucible and adding the appropriate amount of freshly cleaned copper chips (99.9 pct). The molten alloy (at 700°C) was poured into a preheated graphite mold (also at 700°C) and the ingot unidirectionally solidified by impinging water on the steel baseplate of the mold. The alloy was degassed immediately

Jan 1, 1970

Univ of Alabama-University, Alabama-Mining and Metallurgical Society William L Mason, Faculty Sponsor, E C Wright, Dept Head Univ of Alaska-College, Alaska-Mining Society of the Univ of Alaska Douglas W Huber, Faculty Sponsor, E H Beistline, Mining & Metallurgy Dept Head, Troy L Pewe, Geology Dept Head, James Crawford, Chapter Counselor Univ of Arizona-Tucson, Arizona-Miners Society Willard C. Lacy, Faculty Sponsor, J D Forrester, Mining & Metallurgy Dept Head, F. W Galbraith, Geology Dept Head Univ of California-Berkeley, California-Mineral Technology Association H E Hawkes, Faculty Sponsor, Joseph A Pask, Dept Head Carnegie Inst. of Technology-Pittsburgh, Pa -The Metals Club William R Bitler, Faculty Sponsor, Robert F Mehl, Dept Head

Jan 1, 1960

By R. W. Parsons

This discussion concerns fitting an ellipse to angle, where the permeability k is measured for a series of plugs cut from varying angles in the horizontal plane. The conclusions and procedures given by Greenkorn, et al. are in no way affected by these comments, since the degree of anisotropy (ratio of maximum to minimum permeabilities) they found is generally quite close to one (see their Table A-1). However, since large anisotropies may arise, I feel that the comments should be made. Both Marcusl and Scheidegger2 have shown that there are two limiting expressions for the permeability of an unbounded anisotropic media. If the permeability is measured in the direction of the pressure gradient, the result is equivalent to the author&apos;s Eq. 11. This is the equation used to find kl1 and k22 from the experimental data. If, however, the permeability is measured in the direction of flow, then the resulting equation for the measured permeability is From these equations it follows that plots on angle will be ellipses. The principal axes will correspond with the major and minor permeability axes. The question arises as to what permeability is actually being measured on an anisotropic sample in the laboratory. An overall pressure gradient and a gross flow rate are determined and a permeability calculated by Darcy&apos;s law. The details of the macroscopic flow within the sample will be determined by the boundary conditions of the sample and the orientation and magnitude of the major and minor permeability axes. The situation is shown in Fig. 1 for the two-dimensional case. Using the method of conformal mapping, Marcusl has solved the problem of determining the overall apparent (or measured) permeability for this experiment for any condition of W-L ratios and orientation and magnitude of the principle permeability axes. For W-L ratios approaching zero, the streamlines are all forced by the boundary conditions to be in the direction of the measured permeability which is equal to kg. For W-L ratios approaching infinity, the effects of the no-flow bounds are negligible, and the pressure gradient and measured permeatility direction are parall;l. The streamlines are

Jan 1, 1965

By G. Bassi

RECENTLY Wallbaum¹ found that copper wires with different degrees of deformation up to 98.7 pct area reduction recrystallize giving a [112] texture, while deformation over 98.7 pct gives either a [l00] texture at low temperatures or a [1ll] texture at high temperatures. Furthermore it was found that the recrystallization temperature as a function of deformation up to 98.7 pct decreases as expected, but increases over that deformation. Wallbaum concluded that the different textures have different recrystallization temperatures. The [112] texture has the lowest and [Ill] the highest. At the same time Bassi² found that for high deformation (over 99 pct area reduction) and for an annealing temperature of 400°C, the [l00] texture first forms and with prolonged annealing time the [12] texture appears through grain growth. This secondary texture does not appear if the wire is annealed at 1000°C before the deformation. From these two papers it might be concluded that the [I12] texture can appear either as a primary or as a secondary texture after annealing. The texture formed in a special case depends on the previous history of the wire. Probably the texture of the wire prior to the last deformation is important. To investigate this, wires were produced by adequate deformation and annealing to give a [l00], a [112], and a [lll] texture. The wires then were given a series of different deformations and were annealed at various temperatures, after which the textures were studied. Experimental Work The copper used was electrolytic tough-pitch (Cu 99.90 pct and 0, 0.04 pct). Three wires with the different initial textures were made in the following way: The [l00] and [112] by drawing a 16 mm rod to 1 mm and annealing it 16 hr at 200°C and 2 hr

Jan 1, 1953

By D. M. Waldorf

Steam permeability measurements have been made in the laboratory on several samples of natural reservoir materials. The steam temperatures and pressures were selected to simulate conditions which might exist in a reservoir during the injection of steam. For each sample tested, the experimental permeability to superheated steam was comparable to that measured with air and no evidence of plugging was detected. Some samples were exposed to water at various temperatures and plugging was found to occur in materials which contained significant quantities of monmorillonite clay. Temperature had little effect on the degree of plug-ning between 75 and 325 F. The measured pemeabilities tended to increase slightly with temperature, but the changes were small compared with the initial loss of per~neability on wetting. Sequential pemzeability measurements were made on two samples using air, water, steam, water and air, in that order. Both samples were water-sensitive and plugged extensively after the initial injection of water. Upon exposure to superheated steatm the samples dehydrated and their permenbilities to superheated steam were comparable to those initially measured with air. The remaining measuretnetzts with water and air confirmed that the water plugging was reversible and that the samples were not seriorrsly damaged during the tests. INTRODUCTION The swelling of water-sensitive clays during water floods has long been recognized as a potential source of reservoir damage. The recent extensive application of steam injection and stimulation has compounded this problem since both hot water and steam (as well as fresh water at reservoir temperatures) are, at sume time, in contact with the producing zone adjacent to the bore of a steam injection well. The purpose of this paper is to present data which compare the sensitivity of some natural sedimentary rock samples to water at various temperatures, and to super-heated steam. Some properties of montmorillonite clay are briefly reviewed, and comparisons are drawn between empirical data and the predicted behavior of the montmorillonite known to be present in the samples. PROPERTIES OF MONTMORILLONIT E CLAY Water initially adsorbs on dry N a -montmorillonite clay in discrete layers in the interlaminar space between clal platelets. The platelet spacing, which is 9.6 A (angstroms) for a dehydrated clay, has been observed to expand in discrete steps to 12.4, 15.5, 18.4 and 21.4 A spacings, indicating the formation of four discrete layers of regularly oriented water molecules.&apos; The first two layers are easily formed by hydrating a dry sample to equilibrium in an atmosphere with carefully controlled humidity. The formation of the higher layers is more difficult. The usual X-ray diffraction patterns of the more highly hydrated samples indicate a gradual increase in the average spacing betwcen 15.5 and 19.2 A, followed by a discontinuous expansion to 31 A when the weight ratio of water to dry clay is between 0.5 and 1.2.&apos; Platelet expansion above 31 A proceeds monotonically as the moisture is increased and no regular arrangement of the platelets ib observed. Water-sensitivity in sedimentary rocks is usually associated with Na-montmorillonite clay when it is in the noncrystal-line state. Mering3 found that the average lattice spacing of sodium montmorillonite hydrated at 68 F and 70 per cent relative humidity was 15.5 A, and that the spacing, at 92 per cent humidity was 16.5 A. The water adsorbed at the higher humidity has the same free energy as liquid water at 65.6 F. Kolaian and Low&apos; used a tensiometer to measure the thermodynamic properties of water in diffuse suspensions of montmorillonite clays relative to pure water. They observed that water in suspensions as dilute as 6 per cent clay became partially oriented when left undisturbed. The bonding associated with this orientation was not extensive because the free energy difference between the water in suspension and pure water was only a few millicalories per mole. They also found that the measured free energy difference decreased rapidly with temperature and became negligible above 100 F. This evidence indicates that montmorillonites contained in sedimentary rocks would dehydrate to a crystalline structure when exposed to superheated steam, and that the rock permeability measured with steam would be equivalent to that measured with air. The effect of elevated temperatures on the swelline of montmorillonite clays in aqueous suspensions has not been investigated. The Gouy-Chapman diffuse-ion-layer theory has been used to predict the swelling pressure of clay suspensions in dilute salt solutions at room temperature with reasonable success. theory also correctly predicts the direction of the thermal response of Na-mont-morillonite swelling pressures in dilute salt suspensions, 9 Over the temperature range of 33 to 68 F, an increase in

Jan 1, 1966

By FRANK FIRRISTONE

Ix the summer of 1842 my father, William Firmstone, was engaged by Charles Jackson, Jr., of Boston, to examine the conditions in the Lehigh valley as a site for blast-furnaces using anthracite for fuel. In consequence of his report, he was further engaged by Mr. Jackson to build a furnace for him and his partners on the Lehigh canal, 2 miles above the mouth of the river at Easton. Work was begun in the fall of 1842, and the first furnace blown-in in 1844. The history of the works, therefore, from 1844 to 1887, when my own connection with them ceased, covers only four years less than the whole period of the rise, culmination, and commencement of the decline in the smelting of iron with anthracite in America, the beginning of which, in a commercial sense, may be put in 1839.&apos; Although this paper, as the title indicates, is concerned almost exclusively with the furnaces at Glendon, still what was done there was more or less influenced by current opinion in the dis¬trict, and even reflects, to some extent, the changes in opinion and practice with mineral fuel the world over. No. 1 Furnace was built of red brick, on four piers, had three tuyeres and fore-hearth and tymp, as was universal with furnaces using mineral fuel until the introduction of Liirmann&apos;s cinder-tuyere. The dimensions and profile are shown in Figs. 1 and 2. The first hearth (Fig. 1) was of sandstone; all after were of fire-brick (Fig. 2). The profile was no doubt derived directly from Gibbons&apos;s furnace,2 for it appears from W. Firmstone&apos;s note-books that in October, 1840, he visited ." Gibbons&apos; new furnaces building at Corbyn Hall," and I have an old drawing,\

Sep 1, 1909