Search Documents

By Joseph W. Siefke

Jan 1, 1985

By H. Ries

THE stabilization of a gravel road with soil is a method of treatment developed in recent years by the United States Bureau of Public Roads for the purpose of binding the constituents together better, and maintain-ing a more durable surface. The process consists in adding to the gravel or crushed stone and sand, a soil mortar, so-called, of fine sand, silt and clay, mixed in the proper proportions. The coarse gravel and sand supply structural strength and hardness; the fine sand adds embedment support to the coarse sand; the silt acts as a filler to prevent the granular particles from rocking; while the clay serves not only as a binder but also provides pores minute enough to cause connecting moisture films which are supposed to have high cohesive properties1. It will be recognized that the clay is an important ingredient both when wet and dry, and should not show excessive expansion when wet, nor correspondingly high shrinkage in drying, as otherwise there is danger of unseating the nonplastic particles. Such a stabilized road, although an improvement on one with a floating surface, will in course of time be subject to wear, and become dusty when the clay dries out and breaks up. It has been found that if some salts are added to the road mixture they tend to maintain the soil moisture and prevent dustiness of the road or raveling of the road surface. In addition to this, it is claimed that these dissolved salts cause a thinning of the moisture films on the particles, thus permitting greater compaction of the road mixture, and thereby increasing its density. This fact can be proved by noting the increased compaction which a road mixture shows when certain salts are added to the soil water. Since certain chemical substances such as sodium chloride are electro-lytes, the question arises whether they cannot have some effect on. the qualities of the clay in the soil mortar, and perhaps improve them. In view of the fact that certain salts seem to exert a favorable effect on the road mixture it is desirable that they be held in the road soil as long a time as possible.

Jan 1, 1936

By W. P. Haynes

DuRing 1939. there were no discoveries of oil and gas in Rumania worthy of mention. and the only important extension was the anticipated

Jan 1, 1940

By Francois E. Heuze

INTRODUCTION Rock slope stability typically is governed by the geological discontinuities. This stability can be improved by drainage, unloading, adjustment in slope orientation, adjustment in slope angle, and also by reinforcement such as bolts or tendons. This paper addresses the modeling of bolt reinforcement in rock slopes. Most geological discontinuities such as joints have rough surfaces; they dilate during shear displacement. Their shear strength is characterized by two envelopes (Fig. 1); the peak envelope is distinct from the residual envelope when the joints can dilate. If the dilation is restrained transversely, such as with bolts, the normal stress will increase and the joint strength also will increase. It has been demonstrated that this increase may be considerable (Obert et al., 1976). The new normal stress at peak strength is a com- posite function of the properties of the rock mass and of the steel (Heuze, 1979). Hence, the dilation and its resultant effects on joint shear strength must be included in the analysis and design of the reinforcement. We present a model which can be used to perform such an analysis. Early studies of rock reinforcement in mining and civil applications (Lang, 1957 - Panek, 1962 - Osen and Parsons, 1966 - Lang, 19721, did not consider the specific effects of bolts on joint shear strength. In 1973, Heuze and Goodman reported direct shear tests on rough sandstone joints with bolts perpendicular to the joint plane (Fig. 2). The peak shear strength of such joints was greatly in excess of the shear strength of the unbolted joints. The excess

Jan 1, 1983

By Roswell Johnson

ALL strata not yielding oil or gas in commercial quantities or a corresponding amount of water may be called dry in a wide sense. In petroleum geology,, however, we may exclude all sands of too low or fin porosity to yield gaseous or fluid contents to the hole drilled in the sand before any original pressure that its contents may be under is disturbed. Most rocks are of this class and they are not reservoirs in our definition; their "dryness" is wholly a matter of course. What are the contents of the pores or what is the exact porosity of such rocks is of almost no concern to us, for economically they are "dry." What does interest us is the content of a rock having sufficient porosity and the pores of sufficient size to yield oil or gas in commercial quantities, if they were present under original pressure: Dryness of these reservoirs is a matter of supreme practical importance. Three views current as to such dryness seem, to me, to apply in a few cases only. It is the purpose of this paper to give reasons for this position and for believing that, in ordinary sedimentary rocks, there is only rarely a reservoir of competent porosity and undisturbed pressure that is dry in the sense of not yielding water, oil, or gas when first penetrated. 1. Gardner1 writes of some Kentucky sands, "There has never been present any salt water or other water in the sand." Absence of water cannot demonstrate this position. It is necessary to show that the rocks were not laid down in water, but in air, and that they became so enclosed, while still above the water-table of the, ground water, that water has not been able to enter since. Most of these sands, and certainly the productive limestones, were deposited in water; and such sands as have been commercially productive show no reason for believing that the overlying shale or limestone was not laid down progressively from one direction and in water that would have flooded it. No adequate explanation has been offered for this hypothesis, which is so inherently improbable.

Jan 1, 1920

By E. H. Dix

The purpose of this paper is to introduce the subject of Stress-Corrosion Cracking at the Joint Symposium of the American Society for Testing Materials and the American Institute of Mining and Metallurgical Engineers. In this Symposium we are concerned with spontaneous cracking which results from the combined effect of high, prolonged stress, and corrosive attack. Stress-corrosion cracking may be considered a specific phase of the more general subject of the effect of high constant stresses in accelerating the rate of corrosion of metal products. The kindred subject of corrosion fatigue in which the life of a metal part under repeated stresses is reduced by corrosive attack is not a part of this Symposium. Likewise "creep," the failure of a metal part by high constantly applied stress, in the absence of a corrosive environment, is not to be included. How- ever, corrosive influences may have more effect on creep failures than is sometimes realized. The penetration by molten metals such as often occurs during tinning or soldering operations, or by mercury, frequently causes cracking when the part is stressed. Strictly speaking this is not stress-corrosion cracking. However, the committee has decided that this phenomenon should be included in the Symposium. The penetration by molten metals such as often occurs during tinning or soldering operations, or by mercury, frequently causes cracking when the part is stressed. Strictly speaking this is not stress-corrosion cracking. However, the committee has decided that this phenomenon should be included in the Symposium.

Jan 1, 1945

By Joseph W. Leonard

Seven formulas commonly used to evaluate industrial screening efficiency are investigated to determine if they are suitable for calculating the efficiency of rectangular-hole screens. Six formulas were found to be limited in application to square-hole screens. The seventh, although acceptable for evaluating rectangular-hole as well as square-hole screening efficiency, was found to be unwieldy. A new formula is developed based on the concept of misplaced sizes. This proposed formula permits the single step determination of efficiency and is applicable to all types of screening applications.

Jan 1, 1975

By Thomas Fraser, Abreu Alvaro

THE work described in this paper was carried out under the sponsorship of the Foreign Economics Administration and in cooperation with the Departamento Nacionál da Produção Mineral, Rio de Janeiro. The project was undertaken to obtain complete data on the variations in washability of coal to be used for coke manufacture in the steel industry and to determine the economy of preliminary hand-sorting operations. The coal-producing industry of Brazil is in that pioneering stage in which operat¬ing practices and methods are just being developed. Increased wartime demand for fuel, coincident with a drastic curtailment of foreign supplies due to lack of shipping facilities, has put a tremendous pressure on the national industry to furnish more coal. Under this incentive, production facilities are being expanded and new methods of operation are being tested. Such changes are being developed both by improvement of existing methods that originated in the field and by adaptation and modification of methods introduced from the United States and Europe. These mining condi¬tions and mining practices in Brazil are typical of what the American mining engineer will find in many instances when he goes pioneering into the developing coal fields of the Southern Hemisphere. The producing coal fields of Brazil are all in the southern states of that country. The coal measures are in a band roughly paralleling the coast and extending in a generally southwesterly direction from northern São Paulo through the states of Paraná, Santa Catarina and Rio Grande do Sul to near the Uruguayan border in the vicinity of Bajé. The accompanying map1 (Fig. I shows the general location of these fields and also the principal routes of movement of both national and imported coal in a late pre-war year (1940). Statistical data on production by states up -to that year are given in Table I. Rio Grande do Sul is still the largest producer among the coal states; but wartime

Jan 1, 1946

By George S. Rice

The extremely valuable papers and discussions on coal-cluat explosions by Bache,' Eavenson, Shurick, Mannakee,* and Raymond are of unusual interest to me, since it has been my duty to carry on investigations on this and allied subjects for the Technologic Branch of the United States Geological Survey during the past year, and to make a series of coal-dust tests in the explosion-gallery at Pittsburg during a short periocl when its use could be diverted from the pressing work of testing explosives. In several of the discussions mentioned, it has been assumecl that the Technologic Branch of the Survey mas not paying attention to certain phases of the general problem, or to the specific question of temperature and humidity of mine-air in its effect upon the explosibility of coal-dust. This assumption is not correct, since from the time of the establishment of the " Mine-Accident Division," with its subdivisions of explosives, rescue-work, and mine-investigation, the mining engineer.; of the last-named section have made the subject one of chief consideration. Their general duties, including mine-sampling for governmeilt purposes, emergency-calls for rescue-work, and esplosion investigations, have prevented undivided attention, but all of them have been supplied with instruments for such determinations, and special report-forms have been in use and a great many observations made in mining-districts to which the mining engineers have gone. With the idea of obtaining a uniform system of reporting these data, and in the hope that the work may be of service to mining engineers in the field, the collecting blanks in use are shown in Forrns 1 and 2.

Jan 1, 1911

By L. D. Stamp

In view of the comprehensive accounts which have appeared in recent years of the oil fields of Burma, Assam and the Punjab,' this brief account will be restricted to an outline recapitulation of the position of the fields and a note on progress and developments in the last two or three years. It is actually peculiarly difficult to give an account of recent developrnents in the oil fields of the Indian Empire. The companies naturally are compelled to make a return to the Government of India of oil produced. These figures are published annually (about 10 months later) for each administrative district (which may include more than one field) where oil is produced, in the Annual Review of the Mineral Production of India (Records of the Geological Survey of India). Some details of recent developments may be given in the Annual Report of the Geological Survey of India (also published in the Records), but otherwise the companies tend to preserve a policy of extreme secrecy. Some of the smaller companies usually publish wellhead production month by month in order to encourage their shareholders when such figures are encouraging, but the larger companies do not necessarily even give figures of production in their annual reports to shareholders. Occasionally details of new tests, new machinery, and so on, leak out through the daily or weekly press in India, but, except for generalized official statements, no details :ire available as to the number of new wells, depths, wells abandoned, or other figures which are common property in other parts of the world. In the country itself the geologists preserve the utmost secrecy, and at times quite a serious system of espionage is developed. Of recent years there has been a slight tendency towards the pooling of experience, but actually the Indian Empire, particularly of course Burma, where there is a

Jan 1, 1933

By A. C. Bluemel, J. S. Harper, J. H. Jett

Can the mining industry in the United States accept the change and challenge of the "Now Generation" of an entirely new high-performance automated transportation system? Advanced transportation systems for the mining industry can be defined as those which lend themselves to automation and meet definite performance and cost objectives. The term automation shall mean that control of transportation system is accomplished by a closed loop electronic circuit which, when started on command, will continue to cycle as programmed until such time as an intelligent feed-back causes the system to shut down.

Jan 1, 1970

[ ]

Jan 1, 1938

By J. J. Lillie

Sublevel stoping was first developed in the Michigan iron mines many years ago. Since that time this method, and modifications with long hole drilling, have been used in a number of non-ferrous mines and have been described in various papers and articles. With a few exceptions, the operations where sublevel methods have been applied are producers of large daily tonnages from ore bodies of considerable size. In selecting mining methods for small properties or relatively small detached ore bodies, sublevel methods often have been overlooked. The method has been used successfully in relatively small operations at Copper Canyon, Nevada, and, more recently, in mining small ore bodies at Darwin, Calif. As a result of this experience, we believe that a review of the general procedure, the advantages noted, and the results obtained will be of interest to many operators of relatively small mines. General Description Briefly, sublevel stoping consists of, first, driving sublevel drifts at predetermined vertical intervals through the length of the stope block; second, breaking an initial mining slot across the stope; third, driving crosscut benches from each sublevel by slabbing into the slot; and, fourth, breaking the ground between benches. Applicability Since this is an open stope method, it requires wall rock that will stand over reasonable stope lengths without caving or excessive slabbing. Ore must be moderately firm but need not be hard. The method is best adapted to steep dipping, tabular or lenticular ore bodies but may be applied to ore bodies of almost any shape if their vertical extent is appreciable. It can be used with dips that are too flat for successful shrinkage stopes and can be modified for use with slushers on dips below about 40". Initial mining at the Copper Canyon operation consisted of sublevel stopes for the wider ore sections and shrinkage stopes for the narrow sections where ore widths averaged about 15 ft. After some experience and a study of comparative results on completed stope blocks, sublevels were substituted for shrinkage stopes even in the narrow ore widths. Practical stope lengths depend upon the character of the walls and the continuity of values within the ore body. Where blocks of low grade or waste are included in the stoping limits, these areas can readily be left as pillars for intermediate wall support and longer stope lengths may be planned. Raises can be spotted in narrow or low grade areas and stope lengths adjusted accordingly. Stoping Details To illustrate stoping details, assume that we have an ore shoot 15 to 30 ft wide and about 200 ft long, with walls that would stand over a stope length of 80 to 90 ft (Fig1). PRELIMINARY DEVELOPMENT Preliminary development for sublevel stoping would be simple. A service raise is driven at about the center of the block and stope limits planned to leave a pillar around this raise. Sublevel drifts driven each way from this central raise will outline the

Jan 1, 1950

By T. L. Joseph, G. Bitsianes

THE layered structure of partially reduced iron ore was described in a previous paper.' Reduction by hydrogen was found to take place at well-defined interfaces between layers of the solid phases. In the present investigation, a detailed study was made of the wiistite phase that had formed during the partial reduction of a cylindrical compact of chemically pure hematite. An unusually wide band of wiistite permitted a rather detailed study of this phase. The specimen was made from Baker's C.P. hematite in the form of a cylinder 1.5 cm in diameter and 1.8 cm long. A dense ore structure with about 6 pct porosity was attained by heating the specimen in air at 1100°C for 3 hr. To confine reduction to the top surface, a ceramic coating was applied to the bottom and sides of the cylindrical compact. The specimen was then partially reduced in hydrogen at 850°C and subjected to a coordinated sequence of macro-, micro-, and X-ray examinations. A section of the partially reduced cylinder is shown in the macrograph, Fig. 1. Four layers consisting of metallic iron, wustite, magnetite, and unreduced hematite are clearly shown. The effort to force reduction to proceed downward in topochemi-cal fashion was only partly successful, as some reduction occurred along one side and bottom of the cylinder. A rather wide layer of dark wustite phase had formed, however, and permitted sampling for X-ray studies as indicated. To supplement previous work and to study the wustite layer in more detail, ten separate layers were removed for X-ray examination. Broad and diffuse patterns were obtained with the as-filed powders, especially with those of iron and wiistite, and the condition indicated a cold-working and variable composition effect within the respective layers. This condition was corrected by annealing the entire series of powders at an appropriate temperature. For the annealing treatment, the ten powder samples were wrapped in silver foil, sealed under vacuum in small quartz tubes, and heated at 750°C for 16 hr. The specimens were then drastically quenched in cold water to preserve the annealed condition. These annealed specimens were X-rayed in turn and the compiled patterns are shown in Fig. 2. The standard patterns for iron and its oxides have been interjected at appropriate positions for purposes of comparison and phase identification. All of the patterns obtained were clearcut and concise so that positive identifications could be made for all of the phases. The outermost layers A, B, and C were composed almost entirely of iron with a small amount of wiistite being detectable at the X-ray limit of phase detection. Layer D from the iron-wustite interface showed both of these phases. The next four layers E, F, G, and H were all in the dark phase band which had been tentatively identified as wustite by the macroexamination, Fig. 1. The diffraction data with their single-phase patterns of wiistite for these layers checked the visual evidence. Continuing the X-ray analyses after layer H, the macrograph (Fig. 1) shows that layer I came largely from the magnetite zone but included some fringes of the wiistite-magnetite interface. The diffraction pattern for the sample confirmed this observation. Layer J came from the unreduced core of the specimen and its diffraction pattern indicated a preponderance of hematite phase. The reduction behavior of synthetic compacts has thus been found to be similar to natural dense iron ore. The previous results were supplemented with measurements of the diffraction films and calculations of the respective unit parameters. These X-ray data are summarized in Table I and offer some interesting correlations as to the compositions of the various phases undergoing reduction. The iron layers that were analyzed gave lattice parameters close to that of pure iron at 2.8664A. Evidently this iron was present in layers A through D as a pure phase with little or no oxygen dissolved in its lattice. With the wiistite layers an entirely different situation prevailed in that there was a definite and

Jan 1, 1955

By H. W. Camp

Although the situation in the oil industry during the past year has not been conducive to large expenditures for development and research, there is little indication that such expenditures have been curtailed. While few outstanding achievements have been reported, considerable progress has been made in the development of new product,s and the adaptation of petroleum derivatives to new uses. The most important question facing the refiner today is the antiknock quality of his gasoline. This year has seen the widespread adoption of the term "octane number" as a measure for anti-knock values, and in the latter months of the year the public has been made acutely aware of this condition through competitive advertising. Gasoline is no longer priced on volatility and gravity alone, but on octane number as well; and premiums are being paid for material of relatively high octane rating. The situation has grown more and more competitive and has forced refiners continually to raise the octane rating of their regular and competitive grades, and at this writing the same situation exists for premium grades which have possessed relatively high anti-knock properties for some time. Straight-run gasoline produced from paraffin-base or semiparaffin-base crudes has an inherently low anti-knock value, and in order to convert this material to a higher quality it has been found necessary to crack an increasing percentage of the crude oil charge. By completely cracking the heavier portions of the crude and blending back with the straight-run gasoline, it has been possible to produce an average of 63 to 65 octane number gasoline on average Mid-Continent crude. This operation carried to the fullest extent does not suffice, however, and the recent and rapid development of the so-called '(reforming unit," has resulted. The straight-run gasoline fraction is cut into two parts: a light, low boiling point gasoline; and a heavy gasoline or naphtha. The latter containing the low anti-knock portions of the gasoline, is sent through a re-forming unit and subjected either to high temperature or pressure, or both, which materially increases its octane number. On average Mid-Continent the blend of low boiling point straight-run,

Jan 1, 1932

By W. H. McCormick, H. J. Benecki

CONSIDERING that a typical modern drilling machine strikes approximately 2000 blows per min and may develop a force of 30 to 200 ft-lb, de- pending upon size of the drill used, the importance of uniform stress distribution in this type of drilling becomes obvious. If the rod were perfectly symmetrical, and if it did not rotate, the problem would be relatively simple, however, the necessary forging, machining and heat treating operations prevent attaining this state of perfection. Take the modern hollow drill rod. The blow is transmitted not from the striking end of the rod directly through to the point of impact of the bit in the rock, but rather through a somewhat complex tool. To add further problems, this entire assembly is rotated immediately after the impacting blow. Rather than attempt to discuss the magnitude and distribution of stresses, it is desired to present a few things that will minimize unusual stress concentration and produce a rod in which the stress distribution will approach the theoretical ideal.

Jan 3, 1954

By William B. Plank

ENGINEERING educators and industries are worried about the engineering manpower shortage that is predicted as a result of the increasing demand for trained engineers not only by industry but by the armed services. This is in the face of a decreasing supply, as is shown by this and other studies. Not only has the number of entering freshmen been decreasing since 1947, because of a decrease in the number of high school graduates entering engineering, but the total number of high school graduates will continue to decrease until 1958 because of the lowered birth rate during the depression years.

Jan 8, 1951

By David R. Hargis, John W. Harshbarger

The Upper Santa Cruz Basin lies in the drainage area of the Santa Cruz River in Arizona, and extends upstream from the community of Rillito to the international boundary [(Fig. 1)]. The principal water use area lies between, and includes, the cities of Tucson and Nogales. A subsurface geologic barrier near Rillito provides a reasonable dividing line between the ground waters of the upper and lower Santa Cruz basins. The upper basin contains the Tucson and Sahuarita-Continental critical ground water areas. The Tucson water use area encompasses the Tucson metropolitan area and extends from the northern boundary of the basin south to the boundary between the Tucson and Sahuarita-Continental critical ground water areas near San Xavier. The San Xavier use area is the San Xavier Indian Reservation. The north and south boundaries of the Continental use area coincide with the limits of the Sahuarita-Continental critical ground water area. The first study of ground water in this valley was initiated by Dr. G. E. P. Smith in 1905, and the results were published in 1910, followed by a series of bulletins of the Arizona Agricultural Experiment Station, University of Arizona, covering the general field of ground water development and utilization. Beginning in 1939, the ground water branch of the US Geologic Survey, in cooperation with the Arizona State Land Department and the Arizona Water Commission (AWC), published a series of bulletins concerning ground water occurrence and utilization in various areas of the state. In 1975 and 1977, the AWC published the Arizona State Water Plan (Arizona Water Commission, 1975) comprising a detailed inventory of water availability and use in Arizona and a study of alternative futures. The importance of ground water supplies in the Upper Santa Cruz Valley cannot be overemphasized. Metropolitan Tucson, surrounding agricultural areas, and the mineral industry are completely dependent upon ground water. Agriculture has been the largest user of ground water. The land distribution of the Upper Santa Cruz Basin is rural in character with large tracts of land included in national monuments and national forests. The Upper Santa Cruz is one of several state basins that does not depend upon one single industry as its major economic activity. Agriculture, mining, tourism, international commerce, and manufacturing all contribute to a viable economy. The city of Nogales, on the Mexican border, and the city of Tucson, to the North, are the centers of commerce in the basin.

Jan 1, 1982

By V. R. Garflas, J. W. Ristori, R. V. Whetshel

Preliminary estimates indicate that world consumption of petroleum products and related fuels in 1937 shattered previous records with a figure of 1,920,000,000 bbl.; that is, 124,000,000 bbl. more than the 1936 total. The writers, as in previous years, have been unable to account for all the available supply in 1937. This "unaccounted-for" supply, which formerly was thought to go largely into storage in foreign countries, was close to 53,000,000 bbl. in 1933; 93,000,000 in 1934; 111,000,000 in 1935; 75,000,000 in 1936 and 148,000,000 in 1937. As this discrepancy between supply and demand continued year after year, it became evident that other reasons than additional foreign stocks were responsible for it. It can now be stated that the "unaccounted-for" supply (see Table 1) goes to take care of: (1) consumption of petroleum products and related fuels for military purposes, the figures of which have been and are kept confidential by foreign countries, (2) additions to stocks to be consumed for military and nonmilitary purposes in foreign countries on which likewise no information is available, (3) errors incurred in the conversion of figures of production of crude oil, its products and related fuels from "weight" units, as used in Russia, for instance, to their American or "volume" equivalents and vice versa, and (4) to the lack of reliable statistics on production and consumption, particularly from Russia, the

Jan 1, 1938

By R. B. Adair, J. S. Browning

The Bureau of Mines conducted laboratory research to determine the applicability of heavy liquid separation to the evaluation of certain mica ores and plant products. After careful standardization of the particular mica ores and associated gangue, accurate analysis of muscovite content could be obtained from results of heavy liquid separation. Where applicable, the method should be particularly suited to the analysis of ores and control of plant operations wherein savings in time would be of considerable advantage. Specifically, there are many instances where a quick plant control method should enable the production of a more uniform grade of mica concentrate. The laboratory use of various heavy liquids for separating minerals of different specific gravities has been recognized for many years.1-8 Sink-float procedures have proven their utility as a rapid and moderately accurate means for determining the mineral content of ores, test products, and plant products in certain nonmetallic concentrating operations. A standard method of analysis for mica in ore samples has not been published or generally accepted by the mica industry. Recently, the U.S. Bureau of Mines investigated methods for analyzing mica by heavy liquid separation. This report has been prepared to make the methods available to others who may need simple, relatively rapid methods of determining the mica content of ores and plant products. The heavy liquid method of mica determination has recently been adopted by one of the major mica producers for evaluating exploration and mill control samples. DESCRIPTION OF THE ORES AND HEAVY LlQLllD The weathered mica pegmatite ores used in the investigation were obtained from commercial mica op erations in Alabama, Georgia, and North Carolina. The major mineral constituents of the ores were muscovite, quartz, kaolin, and minerals of the feldspar group. The ores also contained minor quantities of biotite, limonite, and tourmaline. A comparison of the specific gravities of the major constituents of the ores (muscovite 2.76 +, quartz 2.65, kaolin 2.61, and feldspar 2.57), indicates that an effective separation of muscovite from the other minerals can be made in heavy liquids at a specific

Jan 1, 1968