Search Documents

By A. Madrazo

The Standing-Katz method for predicting liquid densities of reservoir fluids has been tested using experimental data of 154 bottom-hole or recombined reservoir fluid samples. New pressure- and temperature-correction curves for the Standing-Katz type correlation are presented which improve the accuracy of prediction. INTRODUCTION The present study was undertaken to investigate the known methods of determining liquid densities and to select one of them which might yield a better correlation if additional data were employed. An appropriate correlation would incorporate the following characteristics: (1) ease of handling in the computations, (2) results within engineering accuracy and (3) data easily accessible. After careful investigation of the different methods, the Standing-Katz correlation1 appeared to have these characteristics. The Standing-Katz correlation for liquid densities of hydrocarbon systems is based upon limited data. The original work, which employs apparent densities for methane and ethane, was based on data of 15 saturated crude oils in equilibrium with natural gas. Therefore, a test of the correlation using additional experimental data would serve either to validate the Standing-Katz correlation or to form a basis for corrections if such were necessary. PROCEDURE AND GRAPHICAL SOLUTION The data of 154 bottom-hole or recombined reservoir fluid samples were employed to calculate the densities at 14.7 psia and 60°F by the method described in Table 1. Volume contributions for methane and ethane were assigned from the pseudo liquid density plot (Fig. I), but volume contributions for N2, CO2 and HzS were not considered. The densities computed at reference conditions of 14.7 psia and 60°F were then elevated to their respective temperatures and pressures by the use of the correction curves proposed by Standing.' The percentage differences between the experimental values and the calculated values were determined; these samples were grouped into temperature, pressure and density ranges to determine a possible trend. It appeared that, at temperatures above 160°F, the calculated density values were consistently larger than the experimental density values; however, no obvious trend was found for the density and pressure ranges. There is a relationship between the pressure-correction and temperature-correction curves. This relationship, embodied in the temperature-correction curve, can be expressed as follows. The experimental densities of 125 samples above their bubble points were known. From these isothermal data, it was possible to determine an experimental-density difference between two pressures; and (from Fig. 2*), a calculated density difference between the same two pressures was determined. The relative effect of temperature must be considered in the calculated-density values. The effect of temperature can be determined by entering Fig. 3* at the two densities in consideration and obtaining the change in density at constant temperature. This change, or delta density, must be added

By G. T. Pruitt, T. L. Irby, P. B. Crawford, H. Ferrell

In water flooding peripheral, center-to-edge, line-drive or water-encroachment patterns the question has arisen, "when should a producing well be converted to a water-injection well?". It is realized that, if the producing well is shut in when water breakthrough occurs, some oil could be left in an unswept area. Yet, operation to high water-oil ratios may require processing much additional water. If a well is shut in, "where should the allowable be transferred?". A review of the literature indicates that very few data are available to the engineer to assist him in answering these questions. It is the purpose of this paper to present information which may be of value in selecting the flooding technique and the injection and producing wells and in scheduling injection and production rates. Certain phases of these problems can be studied in the laboratory. The Potentiometric model is well suited for studying many waterflooding problems. This model assumes that steady-state flow exists, that the mobility ratio is equal to one and that gravitational effects are neglected.'-' The three-phase sand model also has been recognized as an effective means for studying certain reservoir problems. Both models were used in making the study reported here. This paper discusses seven cases utilizing various waterflooding techniques. Data for the first five cases were obtained on the potentiometric model. Data for Cases VI and VII were obtained by constructing and flooding an unconsolidated sand pack (a three-fluid-phase system) and by determining the swept area and cumulative oil recovery for various types of operations. APPARATUS AND PROCEDURE The potentiometric model reservoir was 30 in. long X 10 in. wide by about 1/2 in. deep. Four wells were equally spaced in a line array along the lateral center line. (See Fig. 1.) Well No. 1 initially was an injection well for each of the patterns reported. The cases studied with the potentiometric model and sand model are described herein. The laboratory sand model reservoir was a 30- 10-in. rectangular Lucite vessel packed with sand to a depth of about 0.65 in. Four wells were equally spaced in a line array along the lateral center line. The reservoir material was an unconsolidated sand into which the reservoir fluids were mixed to yield fluid saturations of 55 per cent oil, 25 per cent water and 20 per cent gas. The water was added to the sand and the material mixed, after which the oil was added. Kerosene and water, the fluids used, gave a viscosity ratio of 1.64:1. In packing the reservoir, care was taken to assure constant fluid saturations and constant porosities. A new mixture was prepared for each run. During water flooding, a colored water was injected by a constant rate pump. The injection rate was 1.1 B/D/ft of sand thickness. For this series of tests, each of the producing wells was open to the atmosphere and, as in the potentiometric model study, Well No. 1 initially was an injection well for each of the patterns. KESULTS OF POTENTIOMETKIC MODEL STUDlES Two cases (Cases I and 11) involving equal pressure injections were studied, with the following results. Case Water injection was initiated at Well No. 1; the producing wells (Nos. 2, 3 and 4) were operated at constant and equal bottom-hole pressures. When water broke through at Well No. 2 and achieved the selected water-oil ratio, Well 2 was converted to a water injection well, resulting in two injection and two producing wells. The injection pressures at Wells 1 and 2 were maintained equal and constant; pressures at the producing wells were held equal, but they were lower than those at the injecting wells. A similar process was repeated when water broke through at Well No. 3. The flood was terminated when

By W. G. Pariseau, C. H. Schmuck, Fei Duan

The Homestake Mine is located in steeply dipping Precambrian metasediaents, an environment common to a number of world class ore bodies. Development of a pronounced plane of schistosity raises a question concerning the importance of anisotropy to the design of vertical crater retreat stopes. Little is known about the actual influence of elastic anisotropy in such -circumstances; even less is known about strength anisotropy. A cautious step- by-step approach was therefore taken towards a numerical assessment of the role of anisotropy in the analysis of stress and stability. The sequence of analyses begins with elementary test problems for computer program checks and proceeds to the analysis of a study stope area between the 6950 and 7100 Levels of the Homestake Mine. Anisotropy (orthotropy) is important at the Homestake Yine. No simple guidelines for evaluating in advance the need for plastic and strength anisotropy in design analysis appear to be forthcoming, ;o that some physical properties testing is necessary where the question is in doubt

Jan 1, 1984

By C. W. Arnold, H. L. Stone, D. L. Luffel

The purpose of this research is to determine (I) the efficiency of small banks of enriched gar driven by methane in displacing oil from a porous medium and (2) the effects of variation in bank size and composition of that efficiency. Most of the experiments were conducted in a sand-packed tube 20-ft long and 1/2-in. in diameter. The hydrocarbon system generally used was methane, butane and decane at 2,500 psia and 160°F. The results of these experiments indicate that, in the regions contacted by the gas, a small bank of an oil-miscible gas driven by methane can displace all of the oil in a piston-like manner. If the enriched gas is of such composition as to remain immiscible with the oil, displacement of oil is less efficient than for the miscible case, and the gas bank travels through the sand with a velocity less than that of the driving gas. These data along with theories discussed imply that smaller banks and less total gas are required when the enriched gas and oil are miscible. INTRODUCTION Widespread application of enriched-gas drive to the recovery of oil rests upon a key factor — the use of limited quantities, or "banks", of enriched gas. At the present time, the value of liquefied petroleum gas or other enriching agents discourages their use in a continuous injection technique, or even in a large bank, except in a few isolated reservoirs. If small banks of enriched gas driven by methane were as effective in displacing oil as is continuous injection, the enriched-gas drive process might be applied to a larger number of reservoirs. Previous research on the mechanics of the enriched-gas drive process reported by Stone and Crurnpl and by Kehn, Pyndus and Gaskell has utilized continuous injection of enriched gas. This work has shown that two types of displacements occur. With gases containing sufficient intermediates. the oil is displaced misciblv and complete recovery is obtained from the regions swept. When gases are used which contain insufficient intermediate hydrocarbon for miscible displacement, oil is displaced immiscibly. In the latter type, selective solution of the intermediate hydrocarbons causes a swelling and reduction in viscosity of the oil and leads to an increased recovery over that obtained by dry-gas (methane) drive. The size of the enriched-gas bank necessary for efficient displacement of oil is determined by those factors which cause deterioration of the bank. A differentiation may be made between those factors which operate on a microscopic scale and those which act on a macroscopic scale. On the smaller scale, the enriched gas mixes in the direction of flow by diffusion and convection with the fluids immediately preceding and following it. On the larger scale, the gas may by-pass the oil by flowing through permeable streaks, by overriding the oil because of density difference, or by fingering because of unfavorable viscosity ratios. In such cases, the enriching material tends to mix with the oil both laterally and in the direction of flow. The increase in effective area available for diffusion and dispersion of the enriching components leads to a faster degradation of the bank and a need for a larger bank than is necessary for those cases in which no by-passing occurs. The effects of such macroscopic factors in the deterioration of enriched-gas banks have been reported in a separate paper by Blackwell, Terry and Rayne. The present study was confined to the factors which operate on the smaller scale, in particular to the behavior of banks of enriched gas in sands uniformly swept by the gas. Experiments were designed to answer the following questions. 1. Can small banks of enriched gas driven by methane be used to secure oil recoveries comparable to those obtained by continuous injection of enriched gas? 2. What is the optimum bank size (the minimum bank size necessary to obtain a recovery comparable to that obtained by continuous injection of the same enriched gas)? 3. How many total pore volumes of gas must be injected to obtain the maximum recovery when the optimum bank size is used? 4. What is the effect of varying the number of enriching components in a gas bank? This report describes the experimental investigations and discusses the results in terms of their significance to reservoir behavior.

By Robert Glass Cleland

THE MEMBERS of the Phelps-Dodge, Phelps-James co- partnership differed widely from one another in certain aspects of temperament and personality; but in one thing Anson Phelps, William Dodge, and Daniel James were fundamentally alike. They were all bred in the English Puritan tradition. Their creed, moreover, was the stern, militant, uncompromising creed of John Calvin and John Knox. The present generation, harshly intolerant of such a creed, has little understanding of the authority it exercised on the thinking and conduct of its adherents or of the contributions that those same adherents made to human welfare and social progress. The men who accepted its authority "were characterized by a blend of strong individualism and an equally strong sense of social duty, and they submitted their own souls to the same searching scrutiny that they applied to their business ledgers." To all three of the immediate founders of Phelps Dodge, their religion was the most real and important thing in life. It was with them day and night, in joy and sorrow, in loss and prosperity, in their most trivial personal affairs, in business transactions of the greatest moment. It was with

Jan 1, 1952

By J. L. Fitch, B. G. Hurd

The presence of gypsum in samples subjected to standard core analysis introduces serious errors in the measurement of water saturation and porosity. The magnitude of these errors, depending upon the type of analysis procedure used, has been evaluated experimentally and theoretically. Water-saturated pore volumes determined by vacuum distillation or retort procedures may be too high by as much as 48 per cent of the volume of gypsum present. The maximum error in this value determined by Dean-Stark extraction with toluene is 36 per cent of the gypsum volume. If pore space is measured by a Boyle's law type porosimeter the maximum erorr due to gypsum is 38 per cent of the original gypsum volume present. The conscientious core analyst may eliminate the errors caused by gypsum by either of two methods. He may apply suitable corrections for the water of crystallization removed from gypsum, or take special precautions to prevent dehydration of gypsum during core cleaning and alzalysis procedures. These alternatives are discussed and methods for obtaining reliable core analysis data are proposed. Gypsum (CaSO4 . 2H2O) occurs as a common mineral in many of the world's sedimentary basins. In addition to its presence as primary bedded evaporitic deposits, it is often found as secondary replacement zones and pore-fillings in host rocks. That it may cause false indications in porosity, both on neutron logs and in standard core analysis, has been generally recognized. False porosity interpretations from neutron logs result because the chemically bound water in gypsum attenuates neutrons as effectively as free water. Errors in core analysis result when gypsum is dehydrated prior to or during the analysis. Vacuum retort procedures used by many laboratories to determine fluid saturation and porosity effect a complete removal of water of crystallization from gypsum. The crystal water, distilled and collected with free water from the sample, is counted as water-sat11rated pore space. Dehydration of gypsum results in a decrease in volume occupied by calcium sulfate and a corresponding increase in pore volume. Thus, if gypsum is dehydrated by sample cleaning and drying procedures, subsequent porosity measurements with gas expansion or compression instruments will be high. The qualitative effect of gypsum on porosity determinations by retort procedures was discussed in a recent article by Bynum and Koepl3. They concluded that since false porosity was interpreted as being water saturated, determinations of oil content were not affected. Others in the industry, however, have pointed out that porosity values are often used with values of water saturation determined independently, e.g., from electric resistivity logs in making reserve estimates. Values of water saturation calculated from the formation resistivity using the Archie equation, S4= are actually low if values of are high due to gypsum. In this case, false porosity values due to gypsum could cause serious errors in calculations of oil-in-place. This investigation was made to determine quantitatively the effect of gypsum on porosity values determined by different core analysis procedures. EXPERIMENTAL PROCEDURES Dehydration of Gypsum The extent and rate of removal of water of crystallization from gypsum under conditions encountered in core analysis procedures were studied. Taken for the experiments were three types of relatively pure, naturally occurring gypsum, viz. selenite, satin spar and massive gypsum. Although all samples probably contained trace chemical impurities, each type lost the theoretical amount of water upon complete dehydration. An automatic recording thermobalance, similar to one described by Mauer2, was used to obtain dehydration rate data for samples heated in dry air. Water

By C. E. Reistle

All crude oils become more viscous when chilled, but the only oils that congeal and precipitate paraffin to such an extent as actually to cause production troubles are those that contain an appreciable amount of wax. In handling these oils of high wax content, three distinct problems may be encountered before the oil reaches the refinery. The first problem is the precipitation and accumulation of paraffin in the well, either in the oil string or on the face and in the pores of the sand. The second problem is the accumulation of paraffin and the congealing of oil in the transportation lines. The third problem is the precipitation of paraffin and the formation of tank bottoms. Factors That Control the Solubility of Paraffin in Crude Oil Two main factors, possibly three, govern the solubility of wax in crude oil. The first of these is temperature. The solubility of wax in crude oil increases with an increase in temperature, and as the temperature approaches the melting point, the wax becomes soluble in all proportions in the crude oil. The higher the melting point of a wax, the less soluble it is in crude oil below its melting point. All crude oils containing wax can be chilled to a point where the oil is saturated with wax. If the temperature is decreased below this point, some of the wax will crystallize from solution. Fig. 1 shows the effect of temperature on the solubility of crude paraffin in oil. The second factor is the amount of volatile constituents and gas removed from the crude oil. Evaporation of the volatile constituents and gas lessens the volume of the oil and concentrates the solution of wax in the oil; therefore less wax can be held in solution at a definite temperature. As the natural amount of wax present in the oil is constant, this results in the oil becoming saturated with wax at a higher temperature than if the volatile constituents and gas were still in the oil. As an example of this, a fresh sample of crude oil having a gravity of 39.8

Jan 1, 1928

J. T. Pullon, Rowangarth, Roundhay, Leeds, England :— In discussing Mr. Lee's paper, I wish to call attention to the fact that Mr. B. II. Thwaite (who was heard here yesterday on the subject of the application of blast-furnace gas for the production of power, of which he was undoubtedly the pioneer) read, at the Engineering Congress in Glasgow in 1901, a paper on the profitable utilization of power from blast-furnace gases,' in which he suggested the diversion and cleaning of the whole of the waste gases coming from the blast-furnace and their utilization for power-production, so as to obtain, with proper manipulation, from 4 to 6 times the efficiency of present methods. He suggested also the heating of the stoves with producer-gas of a higher and therefore more suitable calorific value, so as to maintain them in a constant state of maximum efficiency, free from dust, and to avoid the irregular working of the furnace, besides obtaining a maximum supply of air-blast, of 15 or even 20 lb. pressure, by means of internal-conibustion blast-engines driven by the cleaned waste furnace-gases, with a surplus of gas left for other uses. Since that time, in view of the necessity of having a stand-by plant, immediately available, in case of strikes or other reasons causing the banking or blowing-out of the blast-furnace, he has developed, as an addition to his other types of producer, a high blast-pressure gas-generator, producing a gas identical with, or somewhat superior to, blast-furnace gas; and in which all the ash of the fuel is turned into fluid slag, which is available for, the production of slagwool. The gas is a little richer in carbon monoxide than average blast-furnace waste gas, and has only from 1 to 3 per cent. of hydrogen. Fig. I, drawn from a photograph, shows a plant containing this generator, now in operation at Leeds. It is made in units of from 1,000 to 10,000 h.p. capacity for each vessel, and coupled,

Jan 1, 1907

By Robert Livermore

It has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining CO. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining CO. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently fay from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, by means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities of ore, and made development in certain

Jan 1, 1915

By H. L. Hopkins, OHIO, L. W. Kemph, CLEVEL AND, E. V. Ivanso

A balanced system of internal stress is set up in any metallic structure by plastic deformation below the annealing temperature. The internaI stress induced by cold rolling or other fabricating processes is generally recognized and its magnitude is known to be, within certain limits, a function of the degree of cold deformation. The plastic deformation that may accompany rapid cooling from elevated temperatures may not materially change the form of the product. The internal stresses so induced are not, therefore, so evident and nonrecognition of their presence has at times led to engineering failures. The heat treatment of aluminum alloys is a relatively new art and little information is available regarding the magnitude of stresses induced during the commercial heat treatment of aluminum alloy products. As the industrial use of aluminum increases, it is inevitable that products of increasingly large volume will be required. It has become necessary in the present commercial utilization of aluminum to heat-treat castings and forgings weighing hundreds of pounds. One of the factors governing the magnitude of internal stresses arising from rapid cooling from elevated temperatures is that of the size of the structure being treated. Some of the other factors are: cooling rate, elastic properties of the alloy, thermal expansivity, thermal conductivity, and the presence or absence of phase changes. Practically all aluminum alloys have a high coefficient of thermal expansion and some are capable of developing relatively high elastic limits. On the other hand, all commercial aluminum alloys have relatively high thermal conductivities, no invariant phase changes, and the quenching temperatures are comparatively low. In the absence of invariant phase changes involving change in the type of crystallographic lattice, the fundamental basis for the development of internal stress

Jan 1, 1934

By George Gauci

INTRODUCTION The Broken Hill orebody was discovered in 1883. The richness of the deposit encouraged rapid development of the field and within fifteen years ten mining companies were operating. By 1940, several companies located in the centre of the field with limited reserves, had ceased operation. These leases have been acquired by Broken Hill South Limited and North Broken Hill Limited. The four companies currently operating in the field are, in order of increasing production rate:¬- Broken Hill South Limited (BH South) North Broken Hill Limited (North BH) The Zinc Corporation, Limited (ZC) and New Broken Hill Consolidated Limited (NBHC) The tonnages treated by each company since the present plants have been in operation are shown in Figure 1. The leases are located as shown in Figure 2, and an aerial view of Broken Hill showing the spread of the City on each side of the line of lode is shown in Figure 3. The present treatment plants date back to the early 1930's when the BH South plant was built. The North BH and ZC plants were built in 1939 and NBHC's in 1952. The three plants built before 1940 have similar crushing and grinding flowsheets. NBHC differs in that it includes rod mills with consequent differences in fine crushing equipment.

Jan 1, 1970

By Edward P. Barrett

DURING the past few years numerous references have been made in the technical press and Bureau of Mines Bulletin 270 to sponge iron' and so-called "direct metal" processes. The idea has been prevalent that sponge iron and "direct metals" are cheap commodities. In many instances it has been proposed that these processes be used to treat low-grade ores, utilizing low-grade coals as reducing agents. It is questionable whether or not high-grade sponge iron can be made from low-grade materials. Particles contain¬ing iron oxide and gangue become, upon almost complete deoxidation, particles containing metallic' iron and gangue. The possibility of mechanically separating the metallic iron from the gangue in these particles depends . on the physical characteristics of the particular ore under treatment. Some ores, in which the minerals constituting the gangue break free from the iron oxide upon crushing, may be concentrated magnetically after the iron oxides have been reduced to metal. The finely disseminated ores are least amenable to concentration. In general, high-grade sponge iron can only be made from high-grade raw materials. Sponge iron containing small amounts of sulfur can only be made from raw materials containing small amounts of sulfur or by

Jan 1, 1930

By J. M. Callow

The selective action of oils for lustrous minerals was first disclosed by Haynes in 1860. In 1885, Miss Carrie Everson elaborated this idea and also disclosed the fact that acid increased the so-called selective action. Her patent called for oils, either animal, vegetal or mineral, also for an acid or salt. The process was tried out on a practical scale in Baker City and Leadville, in 1889, and failed: first, because, as has since been shown, of the unsuitability of the ore to flotation; and second, because the invention was too far in advance of the times. Then followed the Elmore brothers, first with their bulk oil processes and later with their vacuum method. The basic principles of oil flotation were undoubtedly covered by the above inventors, the work done since their time being merely a building up on ground work laid by them. Different kinds of oil, different quantities of oil, and all the varying degrees of agitation, were all exemplified and practiced by them in one phase or another, and the developments that have since been made are but elaborations of the fundamental principles laid down by Haynes, Everson, and the Elmore brothers. In 1902, the Potter-Delprat process was developed in Australia. In this process no oil was used, the mineral being raised by the generation of gas, brought about by the introduction of acid into the pulp. The mineral particles appeared on the surface of the separatory vessel, in the form of a scum or froth, buoyed up by minute gas bubbles attached to them. This no doubt first gave the suggestion of gaseous flotation. In 1902, also, Froment, an Italian, was granted a patent in which he combined violent agitation with oil and gaseous flotation, the gas being generated within the pulp, in much the same way as in the Potter-Delprat process. In the same year, Cattermole came out with a unique method. First, the pulp was emulsified with a small quantity of oil, by violent

Jan 1, 1916

By Laurence Delisle

The aim of this paper is the description of a technique to be applied to the study of sections of metal powder particles, less than 20 microns in diam. with the electron microscope, by the replica method, using for replica a material such as formvar or parlodion. This work originated with the study of particles of tungsten powders. Such particles were too small to be examined in sufficient detail with the light microscope. On the other hand, examination with the electron microscope of the powders dispersed in the supporting film was not found satisfactory because: 1. It did not permit differentiating between single particles and aggregates. 2. It did not show the true outlines of the particles but only the projection of a whole surface. 3. No details appeared. For that reason it was attempted to make replicas of sections of the particles imbedded in a mounting material suitable for polishing and etching. The method proved satisfactory for the examination of tungsten powder and was then extended to car-bonyl nickel and carbonyl iron powders. Procedure Several mounting materials commonly used in ordinary metallography were investigated. The problem consisted in finding a mounting material

Jan 1, 1950

Jan 1, 1900

By Ralph A. Sherman, J. M. Pilcher

BY surface treatment of coal is meant the application of a material, either solid or liquid, to the surface of pieces of coal. The purposes of surface treatment are varied. They may be to identify or "trade-mark" the coal, to modify the burning characteristics, the coking tendencies, or the behavior of the ash, to prevent the freezing of wet coal, or to control the dust. The control of dust is the usual purpose of surface treatment. TRADE-MARKING COAL The application of color to the surface of coal for the purpose of identification and registration of the trade-mark has been practiced to some extent. In 1928, the Glen Alden Coal Co. began to color its coal and adopted the trade-mark, "Blue Coal." The Old Ben Coal Co. later followed a similar practice with "Green Coal." A commoner means of identification of coal has been the stenciling of designs or pasting labels on large lumps or in the distribution of small cardboard tags through the smaller sizes. The details of the method used to color coal have not been revealed. Usually all of the coal is not treated, because of the expense. Only enough pieces are colored to show clearly when distributed through the coal.

Jan 1, 1943

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

By C. O. Swanson

In the iron ranges of northern Michigan, magnetic data have been used as an aid in geologic field work since the time of the earliest surveys. The presence of complex structures containing magnetic formations, and the general scarcity of exposures, guided the early work into this line of attack, and later field studies tended to place more and more emphasis upon this geophysical relationship, until, at present, the collection of magnetic data is a matter of routine in any areal survey. At first, horizontal deflections of the compass needle were the only data collected. In subsequent surveys, greater dependence was placed on dip-needle readings, which record variations in the intensity and inclination of the earth's magnetic field. Recently the trend has been toward adjusting the instrument so as to reduce the influence of changes in inclination, and using a more sensitive modification, called the Superdip,' in weakly magnetic areas. To a minor extent, the magnetometer has also been employed. The object of this paper is to present the writer's experience with magnetic data in this region. The conclusions are based on work covering a period of 10 years, and spread over nearly all of the iron ranges and a large part of the intervening areas. The viewpoints expressed are purely geological ones. In other words, any opinion as to the usefulness of a certain relationship is based upon the writer's experience with it as a guide in interpreting the structures of this region, and not upon its soundness theoretically, nor its usefulness under other conditions. A very brief summary of the conclusions is as follows. The most important step is that of collecting the magnetic data. This requires a suitable adjustment of the dip needle, and sufficient readings to accurately portray the variations in the magnetic field, which are apt to be irregular. Once the readings are taken and plotted in some clear fashion, the interpretation of them is usually merely a matter of observing their relation-

Jan 1, 1934

By M. J. Kirwan, K. A. Covell

This paper covers a brief discussion of pumping 38° to 41° gravity oil from Wilcox sand wells ranging in depths from 4000 to 4900 ft. in the Seminole field, Oklahoma. As recently as a year ago it was the general belief among Seminole operators that most wells in that district could not be successfully or economically pumped. Also the idea was prevalent at that time that the crookedness of the rotary holes would cause a large amount of mechanical trouble and the use of the air-gas lift would leave the wells depleted with sand conditions and fluid levels unfavorable for pumping. At that time it was predicted that wells would be abandoned when the economic flowing and swabbing period was reached. Contrary to these beliefs it has been demonstrated that wells can be profitably pumped to limits as low as 10 bbl. of oil per day where conditions are favorable. The Serllinole field, unusual in its rapid development, has served as an experimental laboratory for many oil field pumping devices with which this paper will not concern itself. Discussion will be confined to equipment and methods in general use throughout the field. The outstanding features of equipment and pumping operations covered in this paper may be summarized as follows: 1. Pumping equipment from the standpoint of prime movers, energy cost, power transmission equipment, derricks, counterbalances, beam hangers, tubing, sucker rods, pumps, etc. 2. Pumping problems peculiar to the Seminole field, including the proper time at which to change from air-gas lift flowing to pumping. Pumping Equipment There have been no basic changes in pumping equipment in the past 20 years with the exception of some refinements in design brought about by the demand for equipment suitable for pumping deep wells. Results of research in the heat treatment of metals and progress made by the American Petroleum Institute in standardization of equipment, together with the cooperation of oil field equipment manufacturers, have

Jan 1, 1929