Search Documents

By E. H. Jr. Dix

THE use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong-aluminum alloys, magnesium is present to the extent of ½ to ¾ per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth1, 2,3,4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high purity aluminum manufactured by this company .5

Jan 1, 1929

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By Walter Herd

For the past eight years, No. 2 mine of the Cumberland Railway & Coal Co., Springhill-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Depart~ of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. °This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room-and-pillar method was employed, and in January of that year (there being a cessation of work from March to August due to labour troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine, was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In ?the interval, development work for longwall retreating below the 5,900-foot level was vigorously pushed.

Jan 1, 1929

By Z. T. Bieniawski, E. H. Skinner, R. A. Cummings, F. S. Kendorski

INTRODUCTION Caving Mine Drift Support Design The support of production drifts remains a high-cost item facing the developer or operator of an underground caving mine. Support costs are incurred well in advance of ore production, and there is a strong need to minimize these pre-production commitments of capital. Due to the extensive rock loads that normally develop during the caving process, the support used in caving mines is typically quite heavy and therefore costly. The process of designing this support increasingly makes use of basic tunneling principles, but is hindered by the still-incomplete state of knowledge of rock behavior in caving mines, and high variability of geological conditions in caving orebodies. Caving mines differ from tunnels in that the deformations and rock loads induced are transient and dynamic in occurrence, and are normally large in magnitude, often well in excess of rock mass strength. As opposed to tunnels, caving mine layouts are more intricate, and the methods and effects of construction ordinarily are not as closely monitored. Safety factors in mining tend to be lower and rock masses tend to he weaker. These aspects prevent strict application of tunnel design technology to caving mine drift support, with the result that mine drift supports are commonly designed chiefly on the basis of experience at other mines. Mining procedures at caving mines are evolved in response to site-specific requirements, to the extent that there are really as many caving methods as there are caving mines.

Jan 1, 1983

By D Craw, S Clearwater, S Hammit, C Smith

Prior to rehabilitation, plant cover on quartz gravel overburden at Wangaloa coal mine was highly patchy. Stabilisation techniques have since considerably altered the condition of the main overburden yet deposits in the east and west remain largely intact. On the eastern overburden, three distinct zones of revegetation have naturally developed: Zone 1 represents a dense plant cover, Zone 2 a patchy cover and Zone 3 a sparse cover of isolated plants. Aerial photographs show much of the eastern overburden was deposited between 1940 and 1960s. Yet we found that the temporal scale of deposition did not wholly account for the differences observed in vegetation development. To investigate other influential factors, we set up 12 study plots using four replicates in each vegetation zone. The diversity and density of plants in each plot were measured to quantify the degree of vegetation development. Samples from the substrate in each plot were collected using soil cores to a depth of 10 cm. Cores were analysed for indicators of nutrient availability, metal content and physical composition. We found that substrate chemistry varied between individual study plots, but showed little difference overall along the vegetation gradient. Substrate physical differences were much greater. The ratio of coarse quartz pebbles: fines was considerably higher in Zone 3 than other zones, and within zones where plants were not growing. Bulk density also increased successively from Zone 1 - 3. We found clear evidence for the reversed stratigraphy of excavation superimposed over the time scale of deposition, and the corresponding nature of fine particles. The rate of revegetation was therefore highly dependent upon the substrate composition of the last surface deposit from the dumping truck. Our data suggests an optimum ratio exists between inert coarse material and a fine matrix for progressive natural vegetation development on mine substrates.

Jan 1, 2004

By Nolan Eckroade, Nigel Pereira

Wireless electronic blasting systems are a new technology that enable truly wireless initiation through rock, air and water. This is achieved using low frequency magnetic induction waves to wirelessly send a firing command to groups of in-hole primers. Fully wireless initiation not only removes the limitations imposed by a wired connection to each primer in a blast, but also enables users to alter the paradigm of conventional mining techniques to advance operational productivity and reduce personnel exposure to high-risk activities. While initially deployed in underground applications, wireless electronic blasting is now being used in the open cut environment. To capture the early impacts in surface mining operations, case studies conducted at three surface mines evaluated blasts utilizing a wireless electronic blasting system against baseline blasts using conventional, wired initiation systems. The purpose of this paper is to outline the specific learnings associated with wireless electronic blasting in surface mining to date. The paper will include references to these specific case studies as well as benefits realized and applications for the future.

By Hal T. Morris

The main Tintic mining district in central Utah has produced approximately 13,500,000 tons of ore, containing silver, lead, gold, copper, zinc, and other metals, valued at more than $315,000,000. More than 90 per cent of this ore has come from large, irregular ore bodies that have replaced folded and faulted limestone and dolomite strata. Of lesser importance are replacement veins that chiefly cut contact-pyrometasomatized carbonate rocks and fissure veins that cut altered intrμsive bodies and volcanic rocks. The district is in the west-central part of the East Tintic Mountains, a north-trending fault-block range near the eastern margin of the Great Basin. The consolidated sedimentary rocks exposed at the surface and in mine workings are miogeosynclinal deposits more than 10,000 feet thick that range in age from late Precambrian to Late Mississippian. They are folded and strongly faulted and are partly overlain by volcanic tuffs and agglomerates and by extensive flows of porphyritic and vitrophyric quartz latite, latite, and trachyandesite of Eocene age. All of these rocks are locally concealed beneath thick alluvial deposits of Pliocene and Quaternary age. The Eocene and older rocks are cut by dikes, sills, and small stocks of porphyritic quartz monzonite, monzonite, and latite, which are genetically related to the ore deposits. The district is inactive except for the production of halloysite clay and for minor leasing activity and exploration ventures. Several exploration targets remain untested.

Jan 1, 1968

By J. F. Havard

The enterprises based upon the industrial minerals are diversified in geologic habit, mining systems, processing techniques and marketing methods. Nevertheless, in 1972 these enterprises faced many of the same frustrations and hopes and knotty problems and crucial decisions. Volume and profits were generally improved but were uneven in extent and effect. The U.S. cement industry, for example, was unable to meet demand in major markets. It was constricted by a frozen low-level price structure, faced expensive pollution control measures and watched heavy imports penetrating its markets from several European nations, Mexico and Canada.

Jan 1, 1973

By Sun Shao Xian

The Port of Shekou is situated at Shenzhen Bay on the east side of the Pearl River estuary. Geological condition of the site is quite complicated. On top of the sea bed, there is a layer of soft silt 8 - 14 m thick. Under the soft silt, there are intercalated layers of sand, silt and clay. Average surface elevation of the underlying undulatory weathered bed rock is about - 20 m, with a variation of about 10 m. In certain locations, the weathered bed rock is covered with a layer of silt 3 - 4 m thick. This paper gives brief account of three types of wharf structures which are of particular interest, constructed in the last few years: (A) Platform type wharf structure with frontal sheet piling and steel raking pile in the rear; (B) Relieving Platform type structure with steel sheet piling and inclined anchoring HP pile ; (C) Steel pipe pile row supported apron added to a marginal quay. Average construction time of a deepwater berth is about six months.

Jan 1, 1991

By Gustavo Quiquia Mucha

El presente texto describe las experiencias realizadas por la Compañía Minera Milpo SAA en el marco de una gestión social basada en la consulta previa, libre e informada en la Exploración Minera Responsable. En ese sentido, es importante la cooperación entre la empresa minera y la comunidad, así como la incorporación del marco ideológico empresarial y metodológico, basado en los principios del Convenio 169 de la OIT sobre Pueblos Indígenas y Tribales en Países Independientes, las estrategias y las líneas de intervención social de la Compañía Minera Milpo SAA en los proyectos de exploración minera responsable.

Sep 12, 2011

By B. J. Dave, Ashok J. Desai, Allen J. Hulshizer

This paper presents various design and construction considerations involved in developing an underwater installation of lined, large diameter shafts not known to have been previously accomplished for the diameter size, depth or ground conditions identified with the Seabrook Power Station. Outlined approach provides for driving tunnels independent of shaft sinking operation, permits the use of prefabricated shaft lining and incorporates a safe dry tap method for connecting the shafts to the tunnels. INTRODUCTION The Seabrook Power Station, located two miles inland from the Atlantic Ocean, at Seabrook, New Hampshire, is a two unit, nuclear powered, electric generating plant, each unit having a capacity of 1150 megawatts (electric). Typical to all steam driven generators is the requirement for large quantities of water. Requirements for the Seabrook Plant will be met by intaking and discharging approximately 850,000 gpm of ocean water at a considerable distance from the shore line in water depths that render the environmental impact inconsequential. Obtaining, conveying and discharging such large quantities of water represents a major undertaking, particularly under today's environmental controls. Tunnels are well suited to reducing the environmental impact at the Seabrook site by conveying the water about 250 feet deep under the salt marsh (a valuable ecological feature) and under the beach well out into the ocean without any noticeable ground surface disturbance. An alternate approach utilizing trenched piping would have created some disturbances and was environmentally less desirable. The tunnels connect to intake and discharge

Jan 1, 1976

By AIME AIME

THE 122d meeting of the Institute was held in the Lake. Superior Copper and Iron Country Aug. 20 to Sept. 3, 1920 with an approximate registration of 1100 members and guests. This is the 'first visit of, the Institute to this vicinity since 1904 although previously it held meetings there every six or, seven years. 'The eastern party assembled at Buffalo and sailed on the S. S. "Tionesta ". on Friday morning, Aug. 20, arriving at Houghton, Mich., Monday, Aug. 23. En route stops were made at Detroit, where sightseeing auto trips were taken, and at Mackinac Island, where a short stop permitted a visit to the picturesque and historic Fort Mackinac.

Jan 1, 1920

By Steve Kral

The mining industry has waited a long time for the resurgence in commodity prices and demand for its products that it is now experiencing. Base and precious metals prices have reached levels not seen before. Coal prices have also shot up. And there are encouraging signs in the uranium market. China’s nearly out-of-control economic growth is said to be the leading driver for much of this resurgence. But demand for energy, metals and building materials in the United States and elsewhere are also major factors. The result is that expansions and new mines for nearly every commodity are in the works.

Jan 1, 2005

The modern Golden Cross mine entered the production phase in January 1992. The project is designed to produce over 100 000 oz/yr of gold and over 300 000 oz/yr of silver during a mine life of eight years. An open pit and an underground mine are operated producing around 850 000 t/yr of ore, to feed a conventional carbon-in-leach processing plant. Golden Cross is owned in joint venture by Coeur Gold New Zealand Limited (80%) and Viking Mining Company Limited (20 %).   Since the start of production several major aspects of the design have altered. The underground mine began as a mechanised cut and fill operation. The cut and fill stoping progresses in 3.3 m flatback lifts with maximum stoping width of 6 m. Where the ore zone is wider than 6 m a post pillar cut and fill method is used. In 1993 a new bench mining plan was introduced between the 270 and 260 levels. Flatbacking continued in the footwall drives in anticipation of variability of the ore width and orientation. The development of levels below the main service 200 level has indicated a possibility of bulk mining the ore block rather than flatbacks. This could lower mining costs but also introduce higher dilution rates. Development is in the advanced stages for trialing this method.

Jan 1, 1994

By Janet M. Epps

The international climate regulating environmental management in mining is rapidly evolving through the combined influences of the development of international guidelines, resolutions, protocols, treaties and conventions; the influences of the international lending and aid institutions who seek a consistent but constantly evolving standard of environmental performance from their clients; the legal precedents being developed in courts al over the world; and the activities of multinational countries who tend to rapidly upgrade technological performance through their international activities (particularly influencing developing countries). In this rapidly evolving regulatory environment, the more 'models' available to this international pool of resource materials that demonstrate practical. cost-effective and (most desirably) incentive based regulatory mechanisms, the better will be the eventual body of 'international standards' we will al have to work with. Australia can make a significant contribution to this process, however, it has only been on the margin of this dynamic, North American and European led process, up to this time. It is in the Australian minerals and energy industry's best interest to take an active part in the evolution and direction of this process.

Jan 1, 1996

By G. N. Shannon

Keywords: inclusions, slag, modeling, interfacial energy, capillary force, particle flotation, particle separation A previously introduced model of inclusions separating across a steel-slag interface, developed by Nakajima/Okamura and Bouris/Bergeles, is expanded to include different inclusions shapes (octahedral and plate-like, besides spherical) as well as comparison between model ladle-, tundish-, and mold-slags. Investigation of the relation of these shapes with the interfacial capillary force ? which arises due to the dynamic interfacial energy during separation ? has shown that the force has a significant effect on whether the inclusion separates rapidly or settles at the interface. For the slags considered, the most significant physical property is found to be viscosity, which resulted in fast separation times for inclusions in the mold and ladle slags, relative to the more viscous tundish slag. Particle dissolution (using experimental data) is included in separation modeling.

Jan 1, 2005

By L. R. Stace

Arguably, one of the most significant technological breakthroughs that had been experienced during the period when British Coal was the major coalmine operating company in the UK, the use of rockbolts as principal support in underground roadways brought with it the need to re-assess the technical knowledge, management controls and legislative frameworks associated with the support of mine workings. Following a major roof fall in a roadway supported principally using rockbolts in which fatalities occurred, the process of the design of rockbolted support and the systems and procedures that had been put in place to control its use in the UK were further reviewed. The paper discusses the outcome of these reviews, and how the incident initiated a major new interest in strata control research in the UK against the background of the fragmentation of the ownership of the mines following the sale of the former British Coal assets at the end of 1994, together with the proposed introduction of new strata control legislation in 1996.

Jan 1, 1996

By L. E. Cardwell

This publication contains routine analyses and related source data for 377 natural gas samples from 19 States and two foreign countries. Of this total, 373 samples were collected during calendar year 1970. The remaining four samples were collected during previous years, but releases granting per-mission to publish the analyses were not received until 1970. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Twelve previous publications have presented the results of 9,050 gas analyses prior to 1970. The first three, Bulletins 486,6 576,8 and 617,7 contain analyses and related source data on 5,218 gas samples collected from

Jan 1, 1971

By Libby R. Ricafort, Victorio V. Pato, R. S. Pizarro

Introduction Atlas Consolidated Mining and Development Corp. (ACMDC) started gold production at its Masbate gold mine early in 1980. This involved an open-pit mine and a 3.5-k/d (3850-stpd) carbon-in-pulp processing facility (Pizzaro and Antonio, 1981). When this operation started, the mine began stockpiling sub-grade milling material averaging 1 g/t (0.029 oz per st) gold. Furthermore, geologists estimated that there were additional low grade reserves within the ultimate pit limits. These amounted to 2.4 Mt (2.6 million st) with an average grade of 1.1 g/t (0.03 oz per st) gold. The success of low cost heap leaching prompted an investigation to determine if this tech¬nique would be applicable for the low grade Masbate ore. The findings were favorable and a series of laboratory tests were undertaken. These tests indicated the amenability of this subgrade milling ore to heap leaching. Depending on ore size, gold extractions of more than 60% were obtained. To further define operating parameters for a commercial heap leaching plant, a 400-t (440-st) batch pilot plant was built and operated. These test results were used to design the first commercial heap leaching plant in the Philippines. One design concern was the control of solutions during the rainy season. Due to the material's low grade, every effort was made to minimize capital and operating costs. To this end, surplus mining equipment from the copper operations of ACMDC and used machinery in the crushing circuit were considered. Location: The Masbate gold heap leaching operations are located on the northeastern part of Masbate Island, Philippines. This is about 480 km (300 miles) south-east of Manila. Climate: The climate is moderate with two distinct periods. The dry season runs from January through June, and the rainy season extends from July through December. During the wet season, the rainfall at the mine site averages 300 mm/m (11.8 in. per month) for a total of about 2000 mm/year (78 in. per year). However, heavy downpours in excess of 100 mm/h (4 in. per hour) can occur. Geology: Four distinct rock types have been identified in the pit area. They are tuffaceous agglomerates, andesitic agglomerates, metasedimentary rocks, and hornblende augite andesitic porphyry. The tuffaceous agglomerate occupies the northern and western flanks of the mine. Andesitic agglomerates are localized distinctly in the central portion of the volcanic plug within the mine site. The eastern boundary of the mine is occupied by metasedimentary rocks, whereas, the hornblende augite andesitic porphyry occurs as an intrusive within the andesitic agglomerate and tuffaceous agglomerate. Some areas of the pit contain high proportions of clay minerals, requiring an agglomeration step in the flowsheet. This ensures satisfactory percolation through the heaps. Ore characteristics: Gold and silver are microscopically dis-

Jan 9, 1987

By K. L. Paciorek

Organic materials utilized as cable Jacketing, cable insulation, standoffs, insulating boards and potting compositions were identified and d literature survey performed to obtain the required thermal oxidative and moist tracking data. Thirty representative compositions were procured and subjected to thermal and moist tracking evaluations. Tracking was found to invariably result in ignition or glow of the test specimen. Influence of parameters such as electrolyte strength and composition, temperature, conductor spacing, and electrode material were investigated. Volatile s produced by selected insulators on thermal oxidative and electrical stress were identified, quantitated, and their potential impairment action upon a current interrupter assessed.

Jan 1, 1980