Search Documents

By R. F. Hammen

Copper is one of the most widely used metals in industrial processes and is also present in most mining operations. Extraction of copper from solutions often proves difficult due to the presence of complexing agents. ChromatoChem, Inc. has developed a Solid Phase Extraction (SPE) support (HiPAC) for removal and recovery of metals from wastewater. The HiPAC SPE support employs chelating agents covalently coupled to a long linker molecule. Several solutions containing copper and complexing agents were tested including 1) copper and carbonate, pH 9.8, 2) mixed metals and anions with copper and cyanide, pH 11, and 3) copper and the chelating agent EDTA, pH 11. The copper was extracted from solutions one and two at high pH, but the EDTA containing solution needed the pH lowered to make the copper available for capture. In each example, the copper concentration was significantly reduced by HiPAC SPE treatment.

Jan 1, 1994

By Shengli Wu, Mingyin Kou, Feng Chang, Laixin Wang, Hua Lu, Jianliang Zhang

Sintering dust has been regarded as an important secondary resource in a modern steel plant. Sintering dust was mechanically treated using different milling machines and experimental conditions in air atmosphere. The changes in phase constitution, particle size, specific surface area, particle morphology, and lattice parameters of activated sintering dust were determined. It was found that the agglomeration of the particles take place during extended dry milling with accessible pores for Nitrogen gas. The maximum specific BET surface area in the stirring wet grinding and planetary wet grinding increases to 43.06 and 46.45 m2/g after activated 360 min respectively. With the increasing of energy input, the intensity of diffraction peaks of dolomite and hematite gradually decreased. Furthermore, the previous phase almost disappeared eventually under any experimental conditions. In addition, Fourier transform infrared spectroscopy indicates that organic matter and carbonate decompose easier than other phases, especially under stirring wet milling.

Jan 1, 2016

By P. Klut, D. Groult, R. Marechalle, B. T. H. Bonnema

In the past 5 years, Compagnie Europeenne de Dezingage (CED) has developed a successful dezincing process and the St. Saulve pilot plant has evolved into a commercially successful production plant. Currently the plant meets all the required standards for scrap and zinc quality, output capacity, availability, and meets the prescribed environmental emissions standards. The initial process problems relating to zinc recovery, uncontrollable explosions and sodium hydroxide aerosol emissions have all been solved. Presntly, the yearly production of dezinced scrap is around 50.000 tonnes/year; this capacity is enough to supply the local market. This capacity can be increased easily to 65.000 tonnes/year or more. The market for dezinced material is growing due to the increased consumption of galvanized material on one hand and on the other hand the higher demand for high quality scrap. The proven technology of CED is currently patented worldwide, but CED is inviting licensees to implement the dezincing technology in other parts of the world.

Jan 1, 2000

By W. F. Whittaker

Systematic control of process parameters during electrorefined copper cathode production and final product inspection ensures high quality of produced "ORC brand copper. Since 1986, substantial increases in tankhouse productivity have been achieved by a number of technological and process control changes. This paper reviews the changes implemented to achieve higher productivity and cathode quality.

Jan 1, 1992

By Geza Kisvarsanyi

Ore deposits composed of enargite, tennantite, gold, and pyrite have been mined in volcanic rocks of Oligocene age (35 m.y.) at Recsk, Hungary. Vertical and horizontal zoning of the alunitic-argillic alteration and of the ore minerals led to the concept of an intrusive heat source at depth. Subse-quent drilling disclosed a series of ore deposits in a zoned pattern in and around a stock, separated by a barren gap of 1000 meters from the shallow ore. The ore system is in a intracaldera horst-graben structure, formed by collapse and intrusion in a microplate subduction. volcanic-arc tectonic environment.

Jan 1, 1987

By W. G. Davenport

Chapter 4 examined Inco (oxygen) flash smelting of pure chalcopyrite concentrate. It showed that the oxygen and flux requirements for auto thermal smelting are readily determined by a matrix calculation. This chapter extends this matrix approach by applying it to a multi-mineral concentrate.

Jan 1, 2001

By Susanne Pignolet-Brandom

Reflected light microscopy scanning electron microscope energy dispersive spectroscopic analysis and backscatter electron image and electron microprobe chemical analysis have been used to study lead sinter and lead blast furnace slag. These studies provide invaluable information on the phases present their intergrowths, and their chemical composition. Such information increases the understanding of the nature of pyrometallurgical processes and the behavior of minor elements during these metallurgical processes.

Jan 1, 1987

By Mark Jolly

"Over the last ten years or so many man hours have been dedicated to developing methods for simulating shape casting processes. The majority of the methods developed have been devised by a combination of computer, mathematics and materials specialists often with limited knowledge of foundries and foundrymen. As a result of this it would appear that although there are many software packages for the foundryman to use there still exist fundamental misunderstandings as to their usefulness and suitability within the foundry.The paper aims to identify how well current software packages perform. The relationships between physical phenomena, practical defects and software capabilities are presented. Some discussion of the use of criteria functions is also presented. Finally issues arising from the postprocessing of results are discussed as the presentation of the results to the lay-person in simulation techniques is possibly one of the most important aspects in influencing the adoption of this type of software in the foundry community."

Jan 1, 1999

By Corby G. Anderson

For over a century, the Sunshine Mine in Idaho has been a major producer of silver. An estimated 335,000,000 troy ounces of silver has been mined. This has established the Sunshine Mine as the largest single source of silver in the world. Because the dominant silver containing mineral is tetrahedrite, a copper and antimony sulfide, normal metallurgical treatments to recover the precious metal are not practical. Thus, over the course of the company's history, novel, hydrometallurgical technologies have been developed on-site to handle complex, precious metal containing materials. Recently, the use of Sunshine technology has been extended to the recycle of secondary materials. As well, the use of Sunshine technology by other organizations for treatment of both primary and secondary feedstocks containing precious and base metals is an area of growing interest. This paper will provide an overview of Sunshine hydrometallurgical technologies including the applicability of Sunshine technology to the recycling of precious and base metals.

Jan 1, 1995

By Gustavo Díaz, Miguel A. García, Carlos Frías

"Under the auspices of the Commission of the European Union, a consortium composed of six European organi~ations has conducted a project to scale up the PLACID electrowinning cell to industrial size within the Placid process development. This paper is concerning the results and achievement of the industrial cell prototype after more than 1,000 hours operating time and about 10,000 Kg electrolytic lead production. In general, results have been very satisfactory, demonstrating the ability ofthe PLACID electrowinning cell to produce top quality electrolytic lead (> 99.99 %) with high current efficiency and low energy consumption.IntroductionThis paper is concerning the development of an industrial size PLACID electrowinning cell within the PLACID process development. This project began on January 1993 and was finished on April 1996.Lead metal production and manufacturing industries produce large amounts of dusts and also lead bearing slags. Spent lead-acid battery recycling also produces lead oxides from the battery pastes rather similar to those mentioned above. Those lead secondary materials are hazardous and difficult to handle by usual procedures.Existing processes to treat-lead oxides may inflict considerable damage on the environment, incur high operating costs and have limitations to produce top quality lead.The main aim of this project has been to develop a novel hydrometallurgical process able to deal with different lead bearing materials, mainly lead oxide secondaries: lead-acid battery pastes, lead fumes, furnace slags, oxide residues, etc., producing ""four nines"" pure lead in an efficient manner with a benign influence on the environment; it is called the PLACID process."

Jan 1, 1997

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Robert E. Brown

Magnesium recycling has been used to recover both new scrap and old scrap. It was used extensively in Germany during WWII to expand the magnesium supply. There were a large number of magnesium recyclers in the US who got their start smelting old scrap, old airplanes and old waste dumps from the WWII build up. As the world magnesium industry dwindled, only a few companies were left that did magnesium recycling as a primary business. The sand foundries tended to recycle of their production scrap in their melting furnaces. Even the original die casters tended to put scrap directly back into melting furnaces at the die casting machines. As high purity alloys were developed and the use of die castings in automotive work increased, the tendency was to let the magnesium recyclers convert the scrap back to high quality ingot. Automotive use has grown because of the low density of magnesium. This property is the one of the biggest problems to overcome in shipping scrap. Gates and runners from die casting are very irregular shapes and it is very hard to load a truck with enough material to get a low shipping cost per pound. Recent new equipment companies have developed magnesium equipment that is specifically designed to recycle, refine and cast secondary magnesium metal. These melt cells are supplied as integrated units to magnesium casting sites. The cost and effectiveness of this approach will be discussed.

Jan 1, 2000

By J. Alexandre

The use of bricks of soil-cement is proving to be an important constructive methodology due to low environmental impact in the production process of these blocks comparing with conventional bricks are burnt, besides being easy to produce. However during the process of production of bricks, which are compressed, knowledge of the properties of the soil used is critical to the quality and durability of the blocks. The objective of this work is to evaluate the feasibility of using soil from the municipality of Goytacazes for the production of soil-cement bricks. Assays were performed the compaction, liquid limit, plastic limit, particle size analysis, EDX and X-Ray diffraction for later pressed blocks and analyze their compressive strength and water absorption.

Jan 1, 2015

By Guodong Lai, Shixing Wang, Lijuan Chu, Jinhui Peng, Zebiao Zhang

"The beneficiation of poor manganese ores containing phosphate gangue is very difficult by conventional processes, because of the similarities in the physico-chemical properties of the constituent minerals. The shaking table gravity concentration process and concentrated strong acid selective intensified leaching process were used for dephosphorisation of Yunnan manganese ore. The leaching process was effective. The effects of intensified leaching time, solid-liquid ratio and particle size were investigated. The relevant leaching factors were optimized as -0.125+0.088 mm particle size with 68% nitric acid for 24 h when using a solid-liquid ratio of 1:1 at room temperature and atmospheric pressure. Under these conditions, the P/Mn ratio was reduced from 0.0107 to 0.0056, and the grade of manganese was increased from 12.32% to 42.76%. The dissolution of manganese during leaching was negligible.IntroductionManganese and its compounds are widely used in the iron and steel industry as deoxidation and desulfurization agents and as alloying additives [1-2]. Because of the increase in demand, low grade refractory manganese ores are becoming a new source. Many Chinese manganese ores are high in phosphorus, which cannot be used directly for metallurgical purposes. This occurs because phosphorus enters into the metal phase during smelting and its presence sharply deteriorates the mechanical properties of the metal [3-4].Kanungo and Sant [3] investigated the dephosphorization of phosphorus-rich manganese ores by selective leaching with dilute hydrochloric acid. They observed that leaching with dilute hydrochloric acid (0.1-0.6M) could reduce the phosphorus contents to the specified limit of 0.12%. Ye [5] investigated dephosphorization of high-phosphorus manganese ore of the Huayuan type. Using high intensity magnetic separation, roasting and leaching with acid for dephosphorization, as used in the industry, a 40.15% manganese concentrate with a P/Mn ratio of 0.0037 was obtained. Yimin [6] investigated magnetic separation followed by inverse flotation of high-phosphorus manganese ore, and found that the P/Mn ratio could be reduced from 0.046 to 0.002."

Jan 1, 2012

By Daniel Gauthier, Patrick Sharrock, Cedric Verwilghen, Gilles Flamant, Ange Nzihou, Jocelyn Ramaroson

Clean processes are needed to dispose of many wastes. The incineration of 1 ton of municipal solid waste generates 6000 Nm3 of combustion gases contaminated with heavy metals and other pollutants. Gas scrubbing processes are required to clean incineration fumes in order not to transfer pollution to the atmosphere. We are investigating the use of Hydroxylapatite (Ca-HA) particles for use as sorbent for the removal of volatile heavy metals. We have carried out the synthesis of Ca-HA by two precipitation methods from solution and obtained solids with specific surface areas reaching more than 100 m2/g. Preliminary adsorption experiments were conducted in a horizontal furnace by mixing Ca-HA with 5% by weight of cadmium chloride in solid state. The mixture was heated to 600°C under air atmosphere during 6 hours. Chemical analysis of the solids confirmed that 85 % of the cadmium was retained in the solid phase. Such laboratory results showed that Ca-HA is capable of adsorbing cadmium chloride vapors, and pilot scale studies confirmed cadmium abatement in an industrial context.

Jan 1, 2008

By M. Save, N. Menad

"This paper gives the overview of different alternatives to recycle the following wastes: slag, dusts, wastes of electric and electronic equipment (WEEE) and auto shredder residues (ASR). Based on modified Bogue calculations, steelmaking slags were combined in order to produce a belite-rich clinker activated with sulphoaluminate. The EAF dusts containing significant amount of metals can be recycled in different ways: The carbothermal treatment and INTECT process are reported. The results obtained from the model of Auto Shredder Residue injection into blast furnace show that ASR can be used as reducing agent in the BF process if certain conditions are met. The particle size of this material must be controlled to ensure optimal gasification of the material in raceway. The non-ferrous contents may affect the pig iron quality, which is difficult to rectify at a later point. It seems the pyrolysis is the most attractive process to handle ASR. The BRGM flow sheet of WEEE treatment is also reported.I. Introduction The activities of human been may generate wastes and by their accumulation during several years, these wastes may have an impact on the environment and on the human health. These wastes can be generated in the forms of solid, liquid and gas. A variety of industrial wastes can be recycled for use as products. There are three ways in which industrial waste recycling occurs: at the facility itself (on-site recycling), at commercial facilities that gather waste streams from several companies (off-site recycling), and at a company that uses as inputs in its production process the waste products of another company. The industries producing iron and steel may generate different solid wastes which are classified in three main categories: 1. Ferrous material (mainly dusts and sludges from gas cleaning), 2. Slags (these by-products are generated from different process stages), 3. Others by-products (including refractories and material generated from engineering activities). According to this review, the most quantity of the metallurgical wastes is deposed. Currently, the public opinion opposes the creation of new sites. This leads to the growth of the waste disposal costs. Such situation reduces the enterprise competitiveness and decreases their market share on regional and/or national and/or world scales. In these conditions, the economical activities can be decreased leading probably to social problems. The problem of wastes and/or by-products can be treated on three levels:"

Jan 1, 2008

By Ahmet Geveci

In this work it is aimed to assess the plant analytical data which appeared during efforts to decrease the effect of carry-over slag (basic oxygen furnace slag) that can not be prevented to leak during tapping of steel in the ladles. While the amount changes, carry-over slag that escaped to ladle, consists of appreciable amount of reducible oxides (?FetO? and MnO) which act as oxygen source for steel bath. By using aluminum dross, containing %30-35 metallic aluminum, which is a non-recoverable process outcome (discard) for most of the aluminum factories, slag reduction behavior will be analyzed together with other parameters such as reaction time, initial amount of total Fe+MnO, amount of reducing agent and reducing effect of soluble aluminum in steel bath while obtaining a slag composition which promotes higher desulphurization capacity and inclusion removal for liquid steel.

Jan 1, 2006

By H. -Peter Sattler

The laser sorting technique for replacing the handpicking of the non-ferrous metal scrap from auto shredders was first introduced 1990, The process is based on the use of atomic emission spectroscopy induced by lasers to identify the scrap particles and sort them with adequate systems into main fractions of Al-, Zn-and Cu-alloys, stainless steel and lead, In the meantime the handling technique for the scrap, i.e. the singling and sorting technique as well as the analytical detector were further developed for more efficiency and higher reliability, i,e. less maintenance, minor sorting errors etc. These developments were mainly based, on and initiated by operational experiences from the startup phase of a first production plant. Part of the on going research work was the development of an ,aluminium detector which makes it the first time possible to sort mixed aluminium scrap automatically into specific alloy fractions.

Jan 1, 1995

By Hongmin Zhu, Suning Liu, Kai Huang

"Recovery of silicon particles from the cutting slurry for the manufacturing of solar grade silicon is very important to recycle this kind of special resource. The challenge is to separate the silicon particles from the mixed abrasive particles which contain SiC. Various methods such as sedimentation, centrifugation, and flotation have been conducted, while in present work, a simple and effective novel method was proposed to study the separation of Si and coexisting SiC particles in the cutting slurry. The new process is based on the size difference between the two kinds of microparticles. And the membranes with the different pore sizes of 1µm, 2µm, 3µm and 5µm were used to test the pass ratio and separation efficiency of the suspension. Results shows that the effective separation of Si and SiC microparticles was obtained under the optimal conditions, and indicating great potential of practical enrichment of Si from the coexisting abrasive particles.IntroductionWith the development of the world economy, energy shortage and environment problem is becoming more and more seriously. Solar energy, which is regarded as one of the most important new energy in the word, has received much attention and interest from the scientists [1, 2]. More than 80% solar cells are manufactured by the high purity polysilicon as the raw material. The main process of producing silicon wafer is by multi-wire slicing. In this slice processing, large amount of slurry is produced. The slurry contains more than 30% wt silicon powder, silicon carbide powder as the abrasive, scraps of metal chips, as well as cutting abrasive suspension polyethylene glycol (PEG). The high-purified silicon powders are worth recycling and reusing as the materials for preparing solar-grade silicon though it is a big challenge [3].Most of the current studies were focusing on the recycling of the silicon carbide and PEG, while work on the recycling of the high-purified silicon is not so been focused since there is lacking of very effective separation and recovery technologies till up now. Nishijima utilized the method of superconducting magnetic to recycle the abrasive [4]. Wang applied a combinational process of chemical treatment, high-gravity centrifugation, high-temperature precipitation technique and directional solidification to enrich the silicon [5]. And other purification methods, such as centrifugation [6], froth flotation technologies [7], electrical filed separation [8] and phase-transfer process [9] have been employed. The disadvantages such as using poisonous media or complex equipments decrease the feasibility and efficiency of the above mentioned techniques."

Jan 1, 2014

By W. Marnette

Norddeutsche Affinerie is the largest West European copper producer with an annual output of more than 350,000 tonnes of refined copper, about half of which is produced from copper concentrates. However, in addition to concentrates, Norddeutsche Affinerie processes secondary raw materials and recycling materials which contain a combination of copper and lead. These materials were previously treated in blast furnaces, a technology which has meanwhile been superseded at NA by the electric furnace process, primarily owing to the necessity of complying with the increasingly stringent requirements for environmental protection.

Jan 1, 1994