Search Documents

By Jiann-Yang Hwang

Hydrogen storage is a critical issue for the hydrogen economy. Current storage technologies are not able to meet the combined gravimetric, volumetric, and system cost targets set by the Department of Energy. To solve the problem, the development of a new material - perhydride ? is proposed. Perhydrides are defined as materials that contain more hydrogen atoms in their molecules than conventional hydrides do based on the valence. This concept is supported by the versatile bonding capability of hydrogen and the recent discoveries in the chemistry of hydrogen clusters.

Jan 1, 2006

By M. C. Ruiz

The leaching behavior of chalcopyrite concentrate in acidic CuC12-NaCI-O2 solutions was investigated. Experiments were conducted under continuos flow of oxygen at atmospheric pressures. The results indicated that among the variables temperature has the largest influence on the dissolution of chalcopyrite in this medium, and high copper extraction can only be obtained at temperatures near the boiling point of the solution. It was also found that the stirring speed did not influence appreciably the dissolution of chalcopyrite. An increase in the oxygen flow rate up to 0.1 1/min increased the copper extraction. The total chloride concentration affects the dissolution of chalcopyrite up to about 4 M. Copper extraction of 93 % was obtained in leaching chalcopyrite of size fraction -400 # Tyler at 105 OC in 2 hours.

Jan 1, 1997

By Norbert L. Piret

From the copper smelter operation a various outputs are to exert negative impacts on the environment. Particularly, emissions like SO2 and dusts, solid wastes like contaminated gypsum and arsenic sludge, effluents and heated cooling water are generated. Most countries have sitipulated an environmental legislation to provide the framework for an efficient environmental management. As part of the planning activities for x major greenfield copper smelter, the Following elaborations are required and were drawn up. -The Environmental Impact Assessment which is the first step of environmental management and mandatory for every new project. - The Environmental Monitoring Plan, which describes the monitoring procedures for the main impacts identified and assessed. -The Environmental Management Plan, which deals with the minimization of environmental impacts, and the methods of its implementation.

Jan 1, 1996

By David Tisdale, Phillip Mackey, Nagendra Tripathi, Matthew Kreuh, Pascal Coursol

Xstrata Nickel’s Sudbury smelter operation is based on fluid bed roasting of Ni-Cu sulphide concentrate, followed by electric furnace reductive smelting and Peirce-Smith converting to produce a Bessemer matte for electro refining, along with sulphuric acid produced from smelter gas. While the site dates back to the 1930s, the present smelter configuration has been operational since 1978, and currently has a nominal capacity of about 67,000 tpy of contained nickel and is investigating options to expand in future up to 85,000 tpy. As part of a review of plant capacity options, a new metallurgical model of the plant was developed in order to examine a number of processing alternatives. Based on the METSIM™ platform, the present model includes the ability to examine the impact of a number of plant parameters on potential plant performance including; for example, the following: percent of sulphur elimination in roasting, matte grade, degree of matte metallization, temperature, coke requirements, sulphuric acid production, CO2 emissions and overall energy requirements. The process model also includes a number of special features adopted; for example, approaches to effectively model the complex Ni-Cu-Co-Fe-S-O matte system. This paper provides a description of the model and gives an overview of the results. As well as presenting the results of the present study, the applicability of this modeling approach to pyrometallurgical systems in general is also briefly discussed in the paper.

Jan 1, 2009

By L. W. Beckstead

The use of acid ferric sulfate solution as a lixiviant for chalcopyrite concentrates has been of little interest from a practical standpoint due to the formation of a tenacious layer of elemental sulfur which severely impedes the reaction progress. CuFeS2 + 4Fe+3 ?Cu+2 + 5Fe+2 +2s° For example, an acid ferric sulfate leach of chalcopyrite concentrate results in only 12% copper extraction in a three hour leach at 93°C. Experimental results suggest that particle size is the only controllable variable which has a significant effect on the rate of acid ferric sulfate leaching at ambient pressure. Size reduction of the concentrate prior to leaching was exam¬ined using various methods of grinding. Of the grinding methods considered, attrition grinding was found to be the most effective. Leaching of an attritor-ground product (median particle size 0.5 microns) resulted in approximately 90% copper extraction in a three hour leach at 93°C. Energy measurements suggest that the costs associated with attrition mill¬ing are not unreasonable. Evidence indicates that "activation" or stored strain energy is not responsibile for the enhanced reaction kinetics of the finely ground concentrate, but rather the experimental results can be explained simply in terms of the increased surface area due to size reduction. Leaching reaction mech¬anisms operative in the acid ferric sulfate system are discussed and the application of ultra-fine grinding technology to other systems is considered.

Jan 1, 1976

By Ronald Klepper

In hydrometallurgy, pure gases like oxygen and hydrogen are used for oxidation and reduction. The gases are expensive and therefore should be used efficiently. Non reacted gas can be recycled into the liquid. Historically vortex gassing has been used; Le. a mixing impeller close to the liquid surface entrains gas from the headspace into the liquid through a gas vortex. Novel and more efficient methods are surface gassing with up pumping impellers and self- inducing gassing impellers. These alternative impeller systems are well established and common in the chemical industry, but have not been used until recently in hydrometallurgy. Gassing impellers act as internal compressors and increase the interfacial surface for a much higher mass transfer compared to alternate methods mentioned. In the paper results from lab and pilot tests and data from operated plants will be presented. The reactions with gases normally take place under moderate to high pressure, therefore a safe enclosure with mechanical seals and the safety "philosophy" is important. Experienced life and replacement cycles will be reported.

Jan 1, 2000

By Vadim J. Jabotinski

This paper describes several areas of application for electron beam processing of materials. The technology and use of electron beam systems in gas phase synthesis reactions are described. Gas phase reactions may be used to generate ultra- fine metal or ceramic powder that are very pure and crystalline. Among the examples presented are: the generation of nanometer sized metal powders and the gas phase synthesis of silicon carbide for silica and methane. The experimental system is described and future theoretical and experimental objectives are identified.

Jan 1, 1998

By Akira Nishikawa

During the twentieth century, the copper smelting industry achieved dramatic expansion corresponding to the vast growth of global economy. This was largely due to innovations in pyro-metallurgical processes, such as autogenous smelting and continuous smelting and converting technologies. However, as copper production capacity increased, its impact on the environment also could not be ignored, and thus with increasing global environmental awareness, many smelting operations either had to renew or rebuild their facilities. In addition to these changes, in places like Japan and Europe, with scarce primary resources, the treatment and recovery of metals from a variety of items such as car shredder dust, used electrical appliances and electronic devices, on top of scraps traditionally treated, is having a profound effect on the reduction of waste and the preservation of primary resources. Thus compared to the days when copper smelting focused on the environmental control in order to break with "Smoke Stack Industry", copper smelting today is making an important contribution to the sustainable development of human society.

Jan 1, 2003

By Hua Hou, Xiaofeng Niu, Wei Liang

"The explicit finite difference (EFD) method is used for calculating the casting temperature field during solidification. Because the time step is limited, the computational efficiency of the EFD method is lower. In order to improve the computational efficiency, a fourth-order in space and second-order in time model based on the equivalent specific heat method and the alternating direction implicit (ADI) method is established. The degree of similarity between the simulation results and the experimental results is analyzed. The results show that the simulation results of this high order mathematical model are close to the experimental results.IntroductionThe 3D heat transfer equation of temperature field during solidification process is as the following: [1-3]."

Jan 1, 2013

By Junji Shibata

Heavier rare earth, which is contained in a small amount in ores such as bastnesite and monazite, has been accumulated as a heavier rare earth residue without doing separation and purification due to the lack of suitable methods. The heavier rare earth residue includes seven rare earth elements such as Tb, Dy, Ho, Y, Er, Tm and Yb. Separation and recovery process of Dy, Y, Tm and Yb from leached solution of the heavier rare earth residue was investigated by using a column method with solvent impregnated resin. The solvent impregnated resin was prepared by impregnation of organophosphorous extractant whose trade name is PC-88A into a macro porous resin, Amberlite XAD-7. It was almost impossible to separate them in simple adosorption and elution steps. However, we attained to individually separate Dy, Y, Tm and Yb from the leached solution first by changing eluent concentration gradually from pH2 to 0.02kmol/m3 HC1 in the elution step, and secondly by using a development column and changing eluerit concentration in the elution step. The separation process flow was proposed for a heavier rare earth residue by using the solvent impregnated resin method.

Jan 1, 1998

By N. El-Kaddah, J. W. McKelliget

"A mathematical model for the analysis and design of hybrid plasma reactors for advanced materials synthesis is presented. The model is based upon a solution of the electromagnetic vector potential equation and is capable of predicting the two-dimensional velocity, temperature, and electromagnetic fields as well as the reaction kinetics inside the reactor for any axi-symmetric coil configuration. The model is used as a computer aided design tool for the design of hybrid plasma reactors consisting of a conventional DC torch augmented by an RF induction coil and it is demonstrated that the hybrid system possesses superior characteristics for materials synthesis over conventional DC or RF systems. The coupling between the RF and DC components is found to affect both the temperature field and the flow field and to have a significant effect on the reaction kinetics and on materials recovery. The model is used to study the thermal decomposition of silicon tetrachloride as a function of reactor design and operating parameters and it is demonstrated that through a CAD approach it is possible to significantly improve the operation of materials synthesis systems.IntroductionIn recent years there has been growing interest in the use of the inductively coupled plasma for chemical synthesis as a way of meeting the increasing demand for high quality, high performance materials for use in critical applications/l/. Although the basic feasibility of this approach has been demonstrated in the laboratory/2,3/ there still exists a number of operational problems that adversely affect system performance for some applications. In particular, the recirculation and back flow effects that arise from the electromagnetic forces in the plasma can result in the repulsion of the reactants from the hot plasma core and their subsequent deposition on the walls of the reactor. Another operational problem arises from the fact that the energy dissipated in the plasma has to compensate for the heat losses to the environment by conduction, convection, and radiation in order to maintain the ionization of the plasma and, hence, the stability of the plasma may be affected by the presence of the reactants and their products."

Jan 1, 1988

By Zhang Yongzhu

The metallogeneticy and mineralogy of three types of Chinese refractory gold deposits (Au-As; Au-As-MeS; Au-As-C) which are somewhat different from those abroad are discussed. The modes of occurrence, the distribution of grain size, and the morphological features of gold in minerals and their influences on gold recovery by direct cyanidation are also discussed. According to the mineralogy of gold and minerals, bacterial leaching, pressure leaching and roasting technology are suitable for the pretreatment of arsenopyrite-Au, pyrite-Au and carbonaceous-clay-Au refractory gold ores prior to cyanidation, respectively. The most important sulfide pyrite bearing much gold is difficult to be oxidized, its crystalline structure, conduct-types , and minor elements in different mineralizing stages are also discussed. The pyrite aggregates in different deposits are very complicated and much different. Gold grade of arsenopyrite is much higher than that of pyrite for some deposits which have a high correlation coefficient of Au vs As.

Jan 1, 1992

By Robert F. Jenkins

This document addresses the use of practical and basic engineering principles to develop a computer model for the analysis of the various issues which affect heat transfer in aluminum sidewell furnaces. These issues include furnace charge conditions, furnace operating conditions, furnace general arrangement, furnace combustion conditions, and furnace ambient heat loss. The engineering principles applied to this model were first put to test over 20 years ago. A prototype computer model developed 12 years ago has been in continuous use by Thorpe Technologies to determine the performance of sidewell furnaces for the aluminum industry. A new computer model has enhanced capabilities for more detailed performance analysis including regenerative and oxygen enriched combustion.

Jan 1, 2000

By Carlos A. Ferreira, Betina Hansen, Marco A. S. Rodrigues, Marcela P. Proença

"Nowadays, the concern with the reduction of industrial pollution has motivated researchers to found out new technologies for treatment of industrial waste. The clean technologies, as electrodialysis, are capable of treating these residues, minimizing the impacts when they are discarded directly on the environment. Membranes of SPS/HIPS, PAniCSA/SPS/HIPS, SPAN/SPS/HIPS were developed using chemical mixture method. Membranes were characterized by Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA) and Scanning Electronic Microscopy (SEM). Membranes were submitted to electrical polarization and to electrodialysis at NaCl and KCl solutions, in order to determine ionic transport through the membranes. Results were compared with commercial membranes. The average percent extraction for Na+ ions obtained by membrane was beyond 20%.IntroductionThe high environmental impact caused by the galvanoplastic industries represents today a world concern(1). In the galvanoplasty, thin metallic layers are deposited on metallic surfaces(2) through chemical methods or electrochemical process. This industrial process presents some disadvantages that limit its utilization, as the generation of toxic effluents containing concentrations of heavy metals usually above the limits allowed for his release in receiving bodies(1), the production of galvanic sludge which is considered hazardous waste and that is very difficult to treat, beyond the high consumption of water (3).Stimulated by the development of new ion-exchanged membranes with high selectivity, lower electrical resistance, and improved thermal, chemical and mechanical properties, the use of electrodialysis in the wastewater treatment has recently gained a broader interest(5). The electrodialysis (ED) is a mass separation process in which electrically charged membranes and an electrical potential difference are used to separate ionic species from an aqueous solution(5). The technique permits the recovery and the reutilization of the waste products from the industrial process, avoiding the discharge of them on the environmental (acting as clean technology)."

Jan 1, 2008

By M. Fafard, R. Ahmed, O. Dion-Martin

"The optimization of aluminum sheet and tube forming needs the use of large strain finite elements software. The precision of the predicted results from those simulations depends mainly on the quality of constitutive law of the material used. In order to improve quality of these simulations, Barlat has suggested a new yield function named YLD2000-2d. This criterion describes the anisotropic behavior of the rolled aluminum plates. This work consists of characterizing the AA5754 alloy and estimating the material parameters needed for the YLD2000-2d criterion in LS-DYNA. In order to get these parameters, various mechanical testing were performed such as bulge and tensile tests. Moreover, the bulge test was also used to obtain an estimation of work hardening curve in large strain condition, up to 50%. The objective of this paper is to share the experimental results of the characterization of AA5754 aluminum alloy.IntroductionResearchers from National Research Council Canada's Aluminium Technology Center (NRCATC) and Aluminium Research Centre - REGAL, are working on aluminium tube hydroforming processes of AA-5754-0 alloy, used in automotive industries. Hydroforming process presents several difficulties such as wall thinning and section changes. In order to control them, some parameters can be set during the process like pressure rate and end feed level [1]. Given the complexity of the parts and the variability of the control parameters, the use of finite element method (FEA), like LS-DYNA, based on large strain theory is thus necessary. The accuracy of predicted results depends mainly on the quality of the constitutive law used to model the behavior of material. FEA results seem to be valid with the von Mises yield criterion used in some cases. But, given the anisotropic properties of the AA-5754 alloy, a more appropriate criterion could be used. The *MAT_ BARLAT YLD2000 shell material criterion, developed by Barlat [2], who's taking into account the anisotropic behaviour, was chosen due to its large flexibility and its good adaptation to particular elastoplastic behavior of aluminum. However, the use of this criterion needs to determine some material parameters by experimental way."

Jan 1, 2013

By Nathanael Hudson, Ruel A. Overfelt, Sushil H. Bhavnani

"In the aerospace and automotive industries, complex shapes exist which require casting. The problem with these cast parts is the empiricism required to develop the casting process and the accompanying time and expense to develop that process.There has been an interest in using fluidized beds to allow molding sand to better encapsulate the complicated surface geometries of lost foam patterns. Fluidization coupled with a mixing jet helps to homogenize the sand through stirring and may improve the integrity of the casting.At issue is the hydrodynamics of the sand and air around the foam pattern. The commercial package PHOENlCSTM is used to simulate the flow around the pre-casting foam geometry. Employing a two fluid approach, each component is considered a fluid that interpenetrates the other phase. To this end, the kinetic theory of granular 'flow for the sand phase was incorporated into the re-compilable PHOENlCSTM code.The results of this study consist of time-averaged void fraction patterns, with voidage being defined as the fraction of air in the mixture, around the foam pattern submerged in a two-dimensional fluidized bed. The model was benchmarked against past fluidized bed experiments. In order to better understand the dependence of the void fraction pattern around the lost foam pattern, certain physical parameters are varied and the resultant void fraction maps are predicted with the model. Physical parameters such as the aspect ratio of length to width, the placement of the mixing jet, and different mixing jet velocities are varied to illustrate the dependence of the time-averaged void fraction on those variables.Results consistently indicate the presence of channeling around the lost foam pattern, with the extent of the channeling and void formation reliant to a greater degree upon the placement of the mixing jet, and to a lesser degree on mixing jet velocity and aspect ratio.The increase in radial position of the mixing jet from the bed centerline had the desirable effect of granting the churning benefits of a penetrating jet, while at the same time minimizing the formation of excess void fraction at the top of the pattern."

Jan 1, 2001

By C. Frias, M. Garcia, G. Diaz

Advances in hydrometallurgy promoted by Tecnicas Reunidas are providing increasingly simple and clean means for controlling the entire lead recycling chain. Used in parallel with pyrometallurgy, these processes allow furnace temperatures to be reduced and fumes and atmospheric pollution to be minimised. Furnace slags are digested, and residues (mainly gypsum) are non-toxic and convertible into marketable products. In addition, the global economy of the process is substantially improved by reducing the operating cost, increasing the lead recovery above 99% and obtaining a 99.99% pure lead product. These new PLACID and PLINT processes may provide the cleanest and healthiest practicable means for recycling lead from batteries.

Jan 1, 2000

By Ch. -A. Gandin, M. Rappaz

"The grain selection mechanism which occurs during the growth of columnar dendritic structures is routinely used in the investment casting industry to produce directionally solidified (DS) and single crystal turbine blades. However, the evolution of the grain density with increasing distance from the chill has rarely been correlated with the evolution of the grain texture. This contribution presents a three-dimensional (3-D) stochastic modeling approach which permits the computation of grain maps, pole figures and grain density evolutions in DS superalloys. These predictions are compared with measurements resulting from an automatic indexing technique of Electron Back-Scattered diffraction Patterns. This 3-D stochastic model, which applies to uniform temperature situations, has to be extended to the dendritic growth in a thermal gradient. As a preliminary step, a 2-D Cellular Automaton (CA) has been coupled recently to Finite Element (FE) heat flow computations in order to predict the grain structures in complex shape investment cast part. The application of this CAFE model to the investment casting of a turbine blade is presented. Considering these results, the extension of the CAFE algorithm to three dimensions is discussed.INTRODUCTIONThe selection of columnar grains during the directional solidification of alloys plays a key role during the investment casting of directionally solidified (DS) and single crystal (SC) components for aerospace applications [I]. This selection mechanism, leading to a competition of the dendritic network propagation at grain boundaries, has been the subject of many investigations. In particular, the study of Walton and Chalmers [2] is remarkable since it provides a link between the evolutions of the density and of the texture of columnar grains with increasing distance from the mold wall. Since this original work of Walton and Chalmers, two new tools have become available, which enable one to revisit the problem of grain selection in much greater depth. The first one is a fully automatic indexing technique of Electron Back-Scattered diffraction Patterns (EBSPs) [3-6] which directly gives the crystallographic orientation of the solid at any location of the specimen. Pole figures, orientation distributions, misorientations between grains can be visualized very easily with this technique. This information can be directly compared with the results of a second tool: a three-dimensional (3-D) stochastic model (SM) describing the nucleation and growth of grains in a uniform temperature field [6-9]. In order to extend this model to non-uniform temperature situations, a preliminary 2-D model has been developed [10]. It is based on a Cellular Automaton (CA) algorithm coupled with Finite Element (FE) heat flow computations. Since the details of both the automatic indexing technique of EBSPs and the simulation tools have already been published [3-10], only a brief summary is given here."

Jan 1, 1994

By Elli Miettinen, Markku Lahtinen, Ilkka Kojo

"The recent trends of decreasing energy consumption and environmental emissions and utilization of economies of scale are strong drivers favoring continuous copper converting processes. Flash Converting benefits from low off-gas volumes and low investment and operational costs for off-gas treatment. Separate matte and blister furnaces allow the adaptation to concentrate quality changes and flexibility in layout and maintenance.The stationary blister copper bath in Flash Converting furnace is less aggressive to the furnace linings than agitated processes, resulting in low refractory consumption, long campaign life and high on-line availability.Copper Flash Converting has been successfully applied in Kennecott with a campaign life now exceeding five years. A second FCF was started at Xiangguang Copper in China in 2007. The process itself is proven, as its features are similar to those in FSF, Direct-to-Blister and Direct Outotec Nickel Flash Smelting (DON), with one significant difference: it is the easiest of all to operate.The paper presents differences between continuous Flash Converting and conventional converting based on recent experiences and studies."

Jan 1, 2009

By Thomas F. Hagelien, Stein Tore Johansen, Svend Graadahl

"The dross appearing at the surface of an aluminium melt consists, in addition to aluminium, of mainly oxide films but also other non metallic inclusions. The inclusion particles are often poorly wetted by the metal and accumulate at the metal surface. However, in impeller stirred reactors for melt refining stirring may be exceedingly strong and inclusions accumulated at the metal surface may be entrained into the bulk metal. Concerning inclusion removal, such effects may deteriorate the effectiveness of melt refining.In this paper we investigate the surface entrainment of buoyant particles in a water model of an impeller stirred refining reactor. Under varying operating conditions the particle concentration in the bulk liquid is measured by laser light attenuation. The observed entrainment of particles is explained theoretically and metallurgical consequences of the findings are discussed.IntroductionIn the modern cast house continuos metal refining and casting is well established. One of the most distinct advances in metal refining has been the introduction of degassers which introduce bubbles into the metal. The bubbles act to remove dissolved elements together with nonmetallic inclusions. In the most efficient degassers stirring by different kind of rotors is applied to increase mass transfer and inclusion removal. However, it has been known from experience in the cast house that for violent stirring the concentration of some types of inclusions may increase from inlet to outlet of the reactor. This phenomenon has so far been attributed to production of dross in the reactor due to oxidation of metal. Due to removal of inclusions by bubbles the dross layer inside the reactor must be expected to increase in thickness by time. The removed inclusions and produced oxides due to strong stirring is removed at regular interval by the operators of the degasser. However, a fundamental understanding of the phenomena which take place in and below the dross layer is lacking. In the present work we add buoyant particles to the surface of a refining reactor and investigate how these particles may be entrained and dispersed into the liquid depending on the flow conditions. Similar investigations for gas stirred ladles have been performed by Taniguchi et al [1] who found that below a critical gas flow rate all particles are trapped at the surface. Above the critical gas flowrate the surface velocity are sufficiently high to entrain the particles. In this situation it looks like all particles are ready for the melt and a balance between terminal velocity and turbulent dispersion determine the concentration in the liquid."

Jan 1, 1999