Search Documents

By Zhiqiang Han, Anil K. Sachdev, Baicheng Liu, Guomin Han, Alan A. Luo

The growth of precipitate phase ,B-Mg11Al12 in Mg-Al alloy is closely related to interface anisotropy and elastic interaction. The aim of this work is to investigate the effects of the interface anisotropy and elastic interaction on the morphology evolution and growth kinetics of the precipitate. In the work, the precipitation of ,B was studied using phase field modeling. In the model, the chemical free energy of the precipitate and the matrix were obtained via thermodynamic calculation. It is demonstrated that the interface anisotropy results in lath-shaped precipitate and the elastic interaction affects the shape of the end of the precipitate. The interface anisotropy causes uneven growth in different directions and the elastic interaction influences its preferential growth orientation. By combining the interface anisotropy and elastic interaction in the phase field modeling, the results showed that the precipitate phase has a lath-shape with lozenge ends, which is in agreement with experimental observations.

Jan 1, 2013

By Ragnhild Aune

In fire refining of copper, the affinities of various impurity elements on dissolved oxygen is of great significance. Further, in the design of oxygen probes in liquid copper, the influence of solute interactions on the activity of oxygen need to be considered in order to evaluate the oxygen concentration in molten copper. The present paper presents a series of measurements of the activities of oxygen in liquid Cu-M-o alloys (where M stands for Mn, Zn, As, Se or Te) carned out by the present group employing the solid electrolyte galvanic cell technique. Extreme care was taken to control the oxygen potentials in the inert gas atmosphere, and to keep the oxygen levels very low in the molten metal. The oxygen content was determined by analysis of the samples taken out from the melt. The results obtained showed that Mn has a strong negative influence on the activity coefficient of oxygen in liquid copper. A similar, but less prominent effect was observed in the case of Zn. Arsenic had no influence on the activity of oxygen in Cu (liq.). Se and Te had slight negative effect on oxygen activities in copper at XQ >10-5, while at lower oxygen levels the interaction coefficients were found to be positive. The results obtained were compared with empirical models for the calculation of interaction coefficients available in literature.

Jan 1, 2003

By J. A. Jensen

In-situ composites were produced in both Ti matrix (Ti-20Y) and Mg matrix (Mg-20Ti, Mg- 20Nb, Mg-20Fe, and Mg-8Li) alloys. In Ti-20Y, a < 1010 > fiber texture formed in both the Ti and Y phases, and UTS increased from 240 MPa, (as-cast) to 950 MPa after deformation processing to a true strain of 7.3. Deformation processing produced smaller UTS increases in the Mg-matrix composites, but they showed exceptional resistance to weakening from exposure to elevated temperatures. The Mg-20Fe, Mg-20Nb. and Mg-20Ti composites tolerated 6-hour exposure to 400°C with no reduction in their 250 to 300 MPa room temperature UTS. All composites studied had excellent ductility and machinability.

Jan 1, 1995

By William Petruk

A mineralogical and image analysis study was conducted on samples of U tailings from pilot-plant runs on Midwest ore in Northern Saskatchewan. The tailings had been subjected to simulated weathering for the equivalent of 10 years in a tailings facility (lysimeter). The pH varied from 7.0 at the beginning of the test to 5.9 at the end. The results show that during the simulated weathering sane of the gersdorffite, uraninite, galena and pyrite had oxidized, with gersdorffite being the most reactive and pyrite the least. Reaction was evident at the top of the lysilleter , but was most intense at the seepage discharge. sane of the released ions precipitated as Ni, Pb, and U arsenates, sulfarsenates, sulfates and oxides on particles of all minerals. Green crystals of Ni sulfate and white crystals of ca sulfate had precipitated at the surface of the lysilleter. Clay minerals and chlorite had washed from the top of the lysirneter towards the seepage discharge.

Jan 1, 1989

By S. Moussa

The formation of boron-doped nickel aluminides Ni3AI, (76 at. % Ni) from elemental powders by reaction synthesis using reactive sintering was studied. The process involves the mixing of elemental powders of nickel and aluminium with various wt % of boron up to 1 wt % boron. Nickel and Aluminium powders were mixed in the correct proportion to form the intended boron-doped nickel aluminide intermetallic. XRD, SEMI EDS, Image analysis and Archimedes principle; were used to study the effect of Boron addition on the final microstructure, bulk density, average grain size of as reactively-sintered nickel aluminides (boron-doped), compared with no boron addition. The results showed that at greater boron content than 0.3 wt %, a two-phase non-equilibrium microstructure of consisting of NiAI phase in NiJAI matrix was formed that have been primarily retained even after heat treatment for 5 hours at 1000 °C. Boron was present in solid-solution within both the NiAI and the Ni3AI (in greater amounts) phases.

Jan 1, 2001

By A. M. Blount

In 1983, a final ruling of the U.S. Occupational Health and Safety Administration (OSHA) specified that chemicals containing >0.1 % of a carcinogenic substance or > 1 % of a substance hazardous to health must be labelled. Amphiboles of the fibrous or asbestos-type must be quantified at levels of 0. I % whereas the status of non-fibrous types is not finally determined at this time. Tremolite and actinolite can possibly be measured to 0.1 % by XRD, but anthophyllite cannot be so measured. Recently the International Agency for Cancer Research (IARC) has designated quartz as a suspected carcinogen, and its quantity must be measured to the 0.1 % level. Thus, it has become Increasingly important to be able to detect and quantify minerals in bulk samples down to low or "trace" levels. It has been found that minerals needing to be quantified can often be concentrated by microcentrifuge and counted by means of polarized-light microscopy. For example, amphiboles in talc samples can be separated by using a heavy liquid (thallium formate-malonate) of density 2.810. Talc floats, and amphiboles sink. After centrifuging, the denser particles are removed from the bottom with a Pasteur pipette and placed in a clean centrifuge tube. Distilled water is added to the tube containing the denser minerals and the tube centrifuged again. After several washings with distilled water, the sample is removed along with a drop of water to a clean glass slide. A drop of 1 .584 refractive index liquid and a cover glass are placed over the dried sample. The slide is scanned for particles greater than 5 um in length and having an aspect ratio greater than 1:3. These are checked for refractive index, sign of elongation and extinction angle to differentiate them from talc particles on edge and other minerals. Amphiboles have all indices greater than 1.584, and talc has all indices equal to or lower than this value. Alternately the heavies at the bottom of the centrifuge tube can be filtered through a nucleopore filter. After the filter has been washed with distilled water and dried, a 1.584 refractive index liquid renders the filter transparent in two of the four extinction positions so that a count of amphibole particles can be made directly on the filter. The refractive index-density method which is so useful for talc powders should be equally useful for other nonsoluble industrial minerals.

Jan 1, 1989

By Gordon A. Irons, Diancai Guo

"Uneven movement of scrap during melting in an Electric Arc Furnace causes operation problems: cave-ins interrupt electric power input. The movement also influences the radiation heat loss to water-cooled side panels and roof. An apparatus has been built to simulate the flow of scrap that may be interlocked. It has been observed that flow starts at the point where the suspended length of the pile bottom reaches the average scrap size, and proceeds in the form of cave-ins, but scrap pieces slide with each other as ordinary granules. After a cave-in, the pile angle usually remains much larger than the normally observed angle of repose. The force balance of a partially suspended scrap pile has been analyzed, and the equivalent cohesion due to interlocking estimated. A numerical model has been developed to simulate the scrap flow. Simulated results agree reasonably with observed phenomena.IntroductionWhen one considers the melting of steel scrap in an electric arc furnace (EAF), it is helpful to understand the movement of the material during meltdown. As industrial experience demonstrates, scrap movement greatly affects EAF operation. In a typical operation, scrap is dropped into the furnace from scrap buckets. The roof and electrodes are swung into position, and power is applied to the electrodes situated over the scrap. The electrodes ""bore"" into the scrap by melting into the steel in the immediate vicinity of the electrodes as they are lowered. If solid scrap pieces gradually slide towards the arc area, the electric power supply can be maintained at a high level, with few interruptions or drastic electrode adjustments. This results in a high production rate and low power consumption per tonne of steel produced. On the other hand, if the charge moves down unevenly, i.e. in large surges, usually called cave-ins, the electrodes must be drastically raised, and power supply frequently interrupted. This is also accompanied by a high level of harmonics induced in the power network, deteriorating the quality of electricity supplied to other users.In addition, the movement of scrap in an EAF also influences the furnace heat efficiency, as the scrap pile is much closer to the electric arcs compared to the furnace wall and roof, and absorbs more radiated heat. Early exposure of the wall and roof to the arcs will increase the heat loss due to radiation, and reduce the service life of the furnace."

Jan 1, 2004

By Osamu Takeda

A decomposition process for PCBs by using basic molten salts as a reaction field was investigated in order to establish a safe, simple and highly efficient decomposition process for polychlorobiphenyls (PCBs). PCB containing chlorine (e.g. 2, 2?, 4, 4?-tetrachlorobiphenyl) dissolved in n-nonane solution was supplied into basic molten salts (NaOH-Na2CO3 or KOH-K2CO3) maintained at 500-700 ?C together with the carrier gas (N2-21% O2) through an injection tube. The injected PCBs in a bubble are decomposed by the reaction with the molten salts and oxygen during rise in the molten salts. The decomposition efficiency of PCBs increased with increasing temperature and was achieved to be higher than 99.995% in a certain condition. From a series of systematic study, the effectiveness of the decomposition process for PCBs by using molten salts was demonstrated.

Jan 1, 2008

The merging of flash smelting with spray converting in one single furnace is proposed as a continuous copper making process. The proposed process is expected to produce blister copper, clean slag and gas with high sulfur dioxide concentration. Some high grade matte is an intermediate product recycled within the proposed furnace, spray-atomized and converted. The thermodynamic equilibria of the simultaneous oxidations which take place during copper smelting and converting are discussed in order to establish the gradient of oxygen potential along the furnace required for smooth operation. The proposed process is a dynamic system designed to reach equilibrium only close to the slag skimming end of the furnace. The process feasibility is based on the predesigned significant difference between the rates of converting reactions in a finely dispersed system and the rates of deconverting reactions between immiscible liquid phases of restricted interface area. The converting of small stationary droplets of matte, in a silica saturated system, was studied in the laboratory for extremely short oxidation times (10 to 120 seconds). These experiments led to some interesting observations on reaction mechanisms and kinetic trends. The droplet size and the matte grade affected very strongly the oxidation rate and the proportion of the different products obtained.

Jan 1, 1976

By Hiroaki Nakano, Kenji Hara, Shunsuke Kawano, Takeshi Ohgai, Michiaki Ikeda, Hisaaki Fukushima, Shinji Yamashita, Tetsuya Akiyama, Hisayuki Kaku

"Ni-Fe alloys have an inverse magnetostrictive effect (Villari effect) in which its permeability varies according to the ·applied strain. This alloy film has a potential for application as force sensors such as torque sensors, tension sensors and so on. Electrodeposition is promising as a technique for preparing Ni-Fe alloy film because of its convenience and economy. In this paper, the effects of electrolysis conditions on the magnetic properties of electrodeposited Ni-Fe alloy films were investigated. Hysteresis loops of Ni-Fe alloy films on copper substrates from sulfate bath were measured by a vibrating sample magnetometer (VSM). The films of low coercivity, which were preferred when used as a force sensor were obtained by introducing certain additives to the sulfate type bath.INTRODUCTIONNi-Fe alloys show an inverse magnetostrictive effect (Villari effect) that their permeability varies depending on the applied strain. The films of this alloy have a potential for application as force sensors such as torque sensors, tension sensors and so on. The authors et al. tried to prepare Ni-Fe alloy films using the sputtering technique, and produced a prototype of Ni-Fe alloy torque sensor [I]. The sensitivity was higher in the torque sensor thus produced than the strain gauge type one, and this torque sensor enables non-contacted detection. It showed excellent durability and reliability. However, the formation of Ni-Fe alloys by sputtering requires higher costs and brought an another problem that the shape of the substrate on which the film was formed was considerably limited. This causes a hindrance to the wide-range application of the force sensors. Electrodeposition is promising as the technique for preparing Ni-Fe alloy films because of its convenience and economy. In this paper, the effects of the conditions of electrodeposition on the magnetic properties of Ni-Fe alloy films were studied."

Jan 1, 2000

By James Vaughan

Ionic liquids are solvents of interest for applications such as electro- plating, winning and refining of metals. Of particular interest is the possibility of processing reactive metals such as aluminium, magnesium and titanium that cannot be deposited from aqueous solutions. Aluminium has been electro deposited from AlCl3 : ionic liquid mixtures at low temperatures relative to conventional Hall-Héroult smelting. Imidazolium ionic liquids are have been used in the past due to their relatively high ionic conductivity and cation stability. The less studied and less expensive phosphonium ionic liquids systems may provide a viable alternative to imidazolium ionic liquids for certain applications. New information regarding the physical properties and electrochemical behaviour of phosphonium ionic liquid systems is presented.

Jan 1, 2006

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Anze Shui, Joaquin Lira, Cyril Lavelle, Midori Saito, Thierry Poirier

"Dispersed and flocculated alumina (non-spherical particles) slurries were prepared by pH controlling with HCL Spray-drying of these resulted in dimpled granules with a smooth surface and high density, and spherical granules with rough surface and low-density, respectively. Detailed characterization on granules and their compacts includes: SEM observation, density measuring (mercury porosimetry and Archimedes's Principle) and liquid immersion optical microscopy. Compaction of these granules originated a larger particles rearrangement in the samples made with the spherical granules than with the dimpled granules. This was verified through the orientation of alumina particles, which was pronounced in the compact made with the former granules.IntroductionOn immersing a ceramic powder in water, the surface usually acquires a charge by interaction with ionic species in solution. The charge is affected by pH and the electrolyte concentration of the water. 1 The dispersion in a slurry is achieved through the interaction of charges on the particle surface with the media. In the ceramic processing, especially in the process of casting, the dispersion of slurry has been one of the most important topics studied for many years. Recently the attention is paid on its role in the pressing. The granule characteristics are governed by the dispersion state of slurry. Takahashi et al2 , Tsubaki et al3 and Walker et al4 showed that the granules from dispersed slurry were dimpled and of high density, while granules from flocculated slurry were spherical and of low density. This variation in the granules characteristics should have a marked effect on the structure of compact.This paper presents the influence of the dispersion state of alumina slurry on the granules characteristics and also on the internal structure of compacts. Different dispersion states were elaborated by adjusting pH of the slurry. In this method, the particles are dispersed or flocculated only by the effect of surface charging, and thus some secondary effect such as the steric hindrance from an electrolyte dispersant is avoided. The characteristics of granules and compacts are examined with SEM, density measurements by mercury porosimetry and by Archimedes's Principle and liquid immersion optical microscopy. This novel microscopy provides various important information on packing structure of particles, such as their orientation. 5"

Jan 1, 2000

By Pengkai Wang, Huimin Lu, Xiaoxiang Zhang

"In this paper, it was studied an electrochemical reduction process of carbon dioxide in ionic liquids such as 1-n-butyl-3-methylimidazolium hexafluorophosphate ([Bmim] PF6) as the electrolyte. The electrolysis experiments were carried out under current and potential controls. The cathode products contained carbon nanotubes, carbon nanofibers, nanographites, and amorphous carbon. To establish the actual current and potential ranges, the electroreduction of carbon dioxide dissolved in the ionic liquid was studied by cyclic voltammetry on glass-carbon (GC) electrode at room temperature. The electrochemical mechanism of carbon dioxide electroreduction was studied for explanation of all obtained results. Carbon dioxide in ionic liquids was electroreduced, similar to metals oxides being electroreduced in molten salts.IntroductionGlobal warming caused by the increase of carbon dioxide in the atmosphere has become one of the most concerning environment problems, so the solution to this greenhouse effect is very urgent. However, the carbon dioxide is also a cheap and abundant raw material that represents a potential source for the production of chemicals and fuels. Therefore, the development of the technologies that achieve simultaneous reduction and conversion of carbon dioxide to fuels is important. The electrochemical reduction of carbon dioxide is one of the effective approaches to transform CO2. Many investigations have been carried out on the electrochemical reduction of CO2 in both aqueous [1] and non-aqueous [2] electrolyte solutions with different electrodes. The solubility of CO2 in water is very low even under high pressure of CO2, and some investigators have brought focus into the electrochemical reduction of carbon dioxide in organic solvents, because they dissolved much more CO2 than water did. However, the hazardous or toxic properties of organic solvents hinder their use."

Jan 1, 2009

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the furnace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By T. E. Warner

In order to detect arsenic and antimony in zinc, various electrochemcial experiments were performed involving the electrochemical introduction of sodium atoms into molten zinc using a solid electrolyte. Under high rates, the formation of the intermetallic phase NaZn13 was assumed to form. Under more moderate injection rates of sodium, employing a symmetric "zinc/zinc cell", a qualitative relationship between the current generated during cyclic voltammeuy and the arsenic and antimony concentrations in molten zinc was observed.

Jan 1, 1999

By Robert Matusewicz

Ausmelt Technology has been applied to the recycling of spent pot liner (SPL) generated from primary alnminum production. The process is centered on the Ausmelt furnace, in which the SPL is converted under high temperature, oxidizing conditions to an HF containing gas stream and inert slag. fluorine is recovered from the SPL as HF gas and is concentrated and used to manufacture AIF) for recycle to the aluminum smelters. Approximately 87% of the fluorine can be recovered and converted to AIF), with the remainder being effectively tied up in the by product slag. Cost projections show that the recycling process will be competitive with other processes for SPL. The production and recycling of AIF) provides available credit that significantly offsets the operating cost of the facility. Ausmelt Technology for recycling of SPL is currently being marketed in North America by Ausmelt Technology Corporation in Denver, Colorado, and in the rest of the world by Ausmelt Limited of Dandenong, Australia.

Jan 1, 1996

By Kurt Westerlund

Three years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm3/0h at Boliden Rönnskär Sweden on a TBRC smelting galena (PbS). Operating experience from the Kivset flash WHB 11.900 nm3/h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3/h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992

By Grigore Matei

The thermodynamic properties of CU2S-FeS system are important not only in the case of copper smelting but also in the case of general pyro-mctallurgy, However there are not many reported activity data In this study, activities of FeS and CU2S in the CU2S-FeS system were calculated using the Darken&apos;s method from the activity data of the CU2S-FeS-Sb2SJ systems measured by the transportation method at 10S0°C. The activities of CU2S and FeS in the CU2S-FeS system showed negative deviation from the ideal behaviour and satisfied the relation of the Gibbs-Duhem equation,

Jan 1, 2003

By John Anawati

Bauxite residue is an environmentally unfriendly byproduct of alumina manufacturing, produced worldwide in large quantities. This material contains 50– 100 ppm of scandium, a critical material for the production of stronger, weldable, corrosion resistant, and heat tolerant aluminum products. Aircraft manufacturers are particularly interested in Al–Sc alloys because of its ability to form weldable alloys that could potentially reduce aircraft weight by 15–20%. Because of its abundance and low cost, bauxite residue has the potential to be used as an efficient feedstock for valorization processes to recover its scandium content, while in turn degrading this problematic waste. In this project, we developed an efficient process to recover scandium and rare earth elements from a Canadian bauxite residue with high extraction yields, using industrially scalable and economical techniques. The process employs a modified version of sulfuric acid leaching and subsequent impurity removal by selective precipitation. This article outlines the current progress and design rationale in the development and optimization of this innovative and sustainable recovery process.

By C. J. N. Buisman

THIOPAQ technology developed and marketed by PAQUES Bio Systems in Balk, Netherlands, has been successfully used at commercial scale at the Budelco zinc refinery in the Netherlands for the treatment of contaminated groundwater since 1992. In essence, THIOPAQ technology consists of two biological process steps in series: sulfate reduction to hydrogen sulfide (anaerobic) and sulfide oxidation to elemental sulfur (aerobic). The biogenic sulfide produced can be employed for the chemical precipitation of metals in solution either inside the anaerobic reactor or in a separate vessel. Since the solubilities of most metal sulfides are much lower than of their respective hydroxides, considerably lower effluent metal concentrations can be achieved with THIOPAQ systems than in neutralization processes which immobilize metals predominantly by hydrolytic precipitation. In recent years, PAQUES has made significant advances in the design and operation of aerobic and anaerobic bioreactors for metal-sulfur systems. Moreover, the company has increased its technology portfolio to allow the development of more process oriented applications of THIOPAQ technology. A new PAQUES designed plant at Budelco treating sulfatecontaining proceswaters will be started up in 1999. The sulfate reduction is accomplished in a 500 m3 reactor in which hydrogen is used as electron donor. The endproduct, ZnS, is used for Zn and H2S04 production.

Jan 1, 1999