Search Documents

By L. Alagha, O. Molatlhegi, S. Khatibi

"In the present study, the effect of organic/inorganic (hybrid) polyacrylamide polymer on fine coal flotation was investigated. Raw coal samples contain about 37% of ash-forming mineral at a feed size of -75 + 38 um were subjected to flotation tests in the presence of in-house synthesized hybrid Al(OH)3-PAM at different polymer dosages and pH values. Results show a significant improvement in both combustible recovery and ash rejection at 1 ppm polymer dosage. Further improvement of combustible recovery was obtained when flotation was performed at pH 5. Interfacial properties of coal particles before and after flotation were examined through electrokinetic (zeta potential) measurements of coal/water slurries. Zeta potential vs. pH curve were established and compared. In the case of raw coal/water slurry, zeta potential-pH curve resembles the ash-forming minerals (silica and clays) more than coal. After Al(OH)3-PAM-assisted flotation, the zeta potential of froth/water slurry shifted to more positive values point which strongly indicates significant removal of ash-forming minerals from coal by Al(OH)3-PAM. INTRODUCTION Coal has been a major commodity in meeting the world energy demand during the past several decades (Milici et al., 2013). According to the international energy agency, global coal demand will continue to increase for the coming decades. With increasing world population, the global electricity demand would also increase as more people would get access to basic electricity especially in developing countries (Maggio & Cacciola, 2012). Due to this increase in energy consumption, operations in coal mining and beneficiation processes have been highly mechanized to meet the demands. This mechanization has increased the quantity of raw fine coal particles produced which contain high amount of ash-forming mineral matter (slimes). Aplan et al., have reported that the major constituents of ash-forming minerals in U.S.A coal are clay minerals such as kaolinite, montmorillonite and illite (Aplan, 1997). Conventional froth flotation for fine coal cleaning suffers mainly from two major problems: 1) Low recovery of ultrafine coal particles due to slime coating by ash-forming minerals, and 2) The lack of selectivity, which results in the flotation of middlings and entrainment of mineral fines in the froth (Polat et al., 2003). Slime coating on both valuable and air bubbles have been proposed to explain the observed reduction in flotation recovery especially when fine grinding is required. In this case mineral matter may be degraded to extremely fine or colloidal sizes thereby creating difficulty in the water clarification process such as flotation. Slimes inhibit bubble-particle attachment, and increases reagent consumption due to the increase in solid/liquid interfacial area, resulting in low coal recovery."

Jan 1, 2015

By J. G. Asbury

Broadly conceived, the demand for electricity depends upon three sets of variables: (i) the growths of the many individual demands for energy services; (ii) the competitiveness of electrically driven technologies in meeting these demands; and (iii) the energy-conversion efficiencies of installed electrical technologies. The first set of variables establishes the size of the potential market; the second, the market penetration of electrical equipment; and the third, the quantity of electricity required to operate the equipment. All forecasts of electricity consumption ultimately depend upon inferred or assumed relationships to describe the future behavior of these variables. This partitioning of the demand-forecasting problem is conceptually useful and will guide the discussion presented in this paper. However, it is also something of an oversimplification. Examined in more detail, the electricity fore-casting problem is exceedingly complex. The variables mentioned above are, in turn, found to depend upon more fundamental sets of demographic technological, resource, and policy variables. The demand projections developed by the major forecasting services are usually developed in terms of these underlying variables, which themselves must be independently forecast.

Jan 1, 1985

By Nicola Della Valle

The Singapore Land Transport Authority (LTA) is currently expanding capacity by extending their Metro system from South of the city to the North East end of the island. The scope of Contract 704 involved excavating a long reach of tunnel which had a complex rock/soil interface comprised of fresh granite overlaid by clayey sand. Two 6.5 m diameter Earth Pressure Balance (EPB) TBM’s were used to bore the tunnels. These machines were designed so that both hard and soft rock could be excavated. The cutter head was equipped with a combination of both rippers and disk cutters. Soil conditioning was achieved by delivering foam through a multiple port injection system. This very irregular profile of the interfaces posed many challenges to the equipment and the people.

Jan 1, 2001

By Christopher Hebert, Michael R. King, Mehdi Ghazi

The Inland Feeder project is a critical component of Southern California’s water delivery system, relying on a strategic plan of water transfer and storage to enable the delivery of an additional 650 million gallons of water a day. The Arrowhead West and Arrowhead East tunnels form part of this system, comprising the construction of nearly13 km (8 miles) of bored tunnel under the San Bernardino National Forest. This paper describes the design and manufacture of the 4.88 m (16 ft) diameter precast segmental primary lining that will be used in these tunnels to resist rock loads, and up to 275 m (900 ft) of external hydrostatic head.

Jan 1, 2003

By P. M. Soupios

The study of soft soil (wastes above the rock bed) an issue of great importance in civil engineering, is usually addressed by drilling boreholes. This method is rather expensive and time-consuming and although the information obtained is usually accurate, on the other hand it is much localized. Recently published researches have demonstrated the ability of the combination of geophysical exploration methods to estimate the thickness of deposited wastes, which provides the layered structure of the study area and certain, method depended, mechanical parameters as well. By theory, the frequency of resonance of an upper layer is a function of its thickness and the average shear velocity in it. Furthermore, the application of H/V spectral ratios of micro-tremors is a fast, straight forward and cost effective methodology, yielding the determination of the main resonant frequency of the soil. Based on this framework, 20 microtremor measurements have been carried out in a Landfill in Heraklion-Crete. Some of these measurements were deliberately close to drilled sites, where the basement had been reached. Three electrical resistivity tomographies were also used, in order to define the landfill structure such as, thickness, determination of different wastes distribution in the study area and other parameters. In addition, estimation of predictive Vs using empirical relationship between shear velocity and penetration resistance (SPT?s) were also conducted. Knowing the thickness and the resonant frequency, we estimated the shear (Vs) velocity of the waste cover. The final Vs model was confirmed using the results from the Vs-SPT correlation. The combinative implementation of the above mentioned geophysical and geotechnical methods have successfully defined geometrical and geotechnical/geophysical characteristics of the area under investigation in a fast and cost effective way.

Jan 1, 2005

By Alten F. Grandt

Surface mining consists of the removal of the geologic strata overlying the coal seam usually with large electric shovels, draglines or bucket wheels. The method produces more or less parallel ridges or peaks of cast overburden, usually called "spoil banks". The mined lands vary widely in their inherent characteristics to produce a vegetative cover and thus can be put to a wide variety of uses. Use is the key to economic and social benefits. Physical and Chemical Characteristics of Soil Material of Surface Mined Lands after surface mining operations, the soil material is a heterogeneous mass whose physical and chemical properties are dominated by the character of the geologic strata overlying the coal. These strata are highly variable in thickness and character. They may include the surface soil, loess, glacial till, sands, shales, slates, limestone and sandstone rock. The method of mining with the several types of mining equipment will also affect the resultant mined area.

Jan 1, 1968

By P. F. Ziemkiewicz, A. S. Knox

Large-scale use of CCBs in mine environments involves filling surface and underground coal mines with ash to address hydraulic problems, AMD, backfilling and subsidence. The environmental risk of land filling CCBs is generally evaluated by the Toxic Characteristics Leaching Procedure (TCLP) or the Synthetic Precipitation Leaching Procedure (SPLP). However, there is doubt regarding the applicability of these tests to long-term CCBs leaching behavior in groundwater associated with coal mines. The Mine Water Leaching Procedure (MWLP) was developed to provide a site specific risk assessment tool. The MWL Pprocedure is presented in this paper and compared with TCLP as a study.

Jan 1, 2003

By R. Stanevich

Studies by the National Institute for Occupational Safety and Health (NIOSH) and the Bureau of Mines (BOM) have demonstrated that: (1) 90% of diesel particulate is less than one (1) micrometer in aerodynamic diameter; (2) more than 90% of the respirable mass in electric coal mines was greater than one (1) micrometer in aerodynamic diameter; and (3) in coal mines using diesel equipment, average diesel concentrations can represent up to 53% of the MRE respirable coal dust standard. For mines approaching the 2 mg/m3 standard, compliance may be easier to attain by controls directed at diesel exhaust particulate as opposed to coal dust control. First, however, a Simple instrument is needed to measure diesel exhaust particulate concentrations. This paper describes such a sampler, its construction, and use. While results from this sampler are primarily utilized to identify control areas, NIOSH is also using the sampler for estimating worker exposures in epidemiologic studies.

Jan 1, 1988

By Tomek Ulatowski

This article discusses four principal areas relevant to financing direct reduction facilities: (1) Lenders' differing requirements with respect to projected cash flows; (2) The impact of leveraging on project viability; (3) The importance of appropriate debt structure; (4) The significance of accurate and complete capital cost estimates. The overall findings emphasize the inseparable connection between the project economics and its financeability, and particularly how direcly intertwined they both are in the project planning.

Jan 1, 1978

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023

By Charles W. Daugherty, Eugene B. Waggoner

In the construction of recent subsurface projects, particularly mined openings and transit systems, it has been apparent that final costs were often greater than first expected. Because many overruns result from alleged differing site conditions, there was reason to suspect that pre-bid geotechnical investigations were inadequate for predicting subsurface geology. In 1982, nine federal agencies involved in constructing underground facilities funded the National Academy of Sciences' U.S. National Committee on Tunneling Technology (USNC/TT) in an effort to evaluate and clarify the relationship between geological knowledge and construction costs. That committee formed the special Subcommittee on Geological Site Investigations, which spent more than two years studying underground projects by examining contract documents and geologic reports, making site visits, and interviewing owners, designers and contractors. The study ultimately encompassed 84 mined tunnels and chambers and three deep shafts in the United States and eastern Canada. Data collected on geologic exploration, design and construction were analyzed and conclusions reached concerning whether and how site investigations need to be improved. The results of the study are published in two volumes by the National Academy of Sciences. Due to the recent completion date of the main report, it was not possible to prepare a summary for inclusion in the RETC Proceedings. However, the complete two-volume report, "Geotechnical Site Investigations for Underground Projects," can be obtained by writing or calling: U.S. National Committee on Tunneling Technology National Academy of Sciences 2101 Constitution Avenue, N.W. Washington, D.C. 20418 (202) 334-3136

Jan 1, 1985

By MARK J. VANARELLI

Estimating ground-water inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies, including the Chattahoochee and Nancy Creek tunnels, for estimating steady-state ground-water inflows into deep rock tunnels. Statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations, and a semiempirical procedure was used to estimate ground-water inflows. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels that exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semiempirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Modeling using Monte Carlo simulations was observed to be an effective tool for removing data distribution irregularities and incorporating high-end permeability data to derive reasonable ground-water inflow estimates.

By Paul B. Queneau, Barry J. Hansen, D. Erik Spiller

Most lead and zinc secondaries are recycled pyrometallurgically. However, many problems encountered in secondary smelters have been solved by addition of physical concentration and/or hydrometallurgical processing steps, with resulting important environmental benefits. U.S. secondary lead and zinc operations are described, covering conventional smelters, EAF-dust treaters, and zinc sulfate/fertilizer producers, including plant capacities, technologies, and outputs. During the past two decades, remarkable advances have been achieved by recycling spent lead-acid battery components. Interaction between primary and secondary zinc producers, the fertilizer industry, and the zinc chemical industry has substantially decreased waste generation.

Jan 1, 1993

By A. G. Provost

On April 3, 1981, Harrison Western Corporation was awarded a contract by Amax Alloy - A Division of Amax Inc., to sink the Henderson #5 ventilation shaft. The project was located on the Henderson Mine site 88 kilometers west of Denver near the town of Empire, Colorado (Figure I). The Henderson No. 5 Shaft, located in an Alpine environment at an elevation of 3145 meters, was a 9.8 meter diameter concrete lined shaft with a total depth of 793 meters. Work started and continued with Harrison Western employees until January 15, 1982. At that time, Amax made the decision to continue the shaft-sinking with their own labor, and with Harrison Western providing supervision under a management service contract. Shaft sinking continued under this arrangement to October 1, 1982, at which time Amax put the Henderson No. 5 project on standby status until further notice.

Jan 1, 1986

By Lawrence K. Nordell

Historical methods of designing steel cord belt splices are compared with modern finite element modeling (FEM) methods. Dependence of the belt strength rating on the splice dynamic fatigue strengths is reviewed. A number of splice schematics are examined, using simple spring theory and FEM methods. Steel cord wire rope design is discussed. The importance of the insulation gum rubber properties and their splice dimensional factors and tolerances are analyzed. Splice fatigue lie analysis procedure is reviewed. This may be used to predict splice life or time of failure, depending on how the conveyor belt is operated.

Jan 1, 1993

By Thomas E. Ban

D-LM at Mobile The qualified success of iron ore pelletizing processes has influenced considerations for production of highly beneficiated fur¬nace charges. Such beneficiation would necessarily involve some forms of chemical and perhaps thermal conversion for production of prereduced pellets, preheated pellets, precalcined pellets, and perhaps pellets which contain all of the above features as preheated, prereduced, precalcined products. This type of furnace burden will be adapted within a new ironmaking process to be activated commer¬cially during the latter part of 196$ in Mobile, Alabama. This process will integrate a new pelletizing system with an electric smelting furnace and the pellets will be comprised of a composite charge blended from metallurgical proportions of iron ore, coal, and limestone. The plant as designed and constructed by McDowell¬-Wellman Engineering Company will feature the D-LM process and will be owned by McWane Cast Iron Pipe Company. It is significant to

Jan 1, 1968

By Robert A. Jankowski, Ellsworth R. Spencer, Jay F. Colinet

Longwall mining is the most productive method of under- ground coal mining in the United States (US.), and record levels of production have been reached in recent years. These ever-improving production levels have the potential to generate significantly higher quantities of respirable dust. Consequently, the longwall industry continues to struggle with controlling dust liberation and maintaining compliance with the federally-mandated respirable dust standard. In response, longwall operators have in- creased the application of primary dust controls, airflow and water flow, in an effort to improve respirable dust control and reduce worker exposure. Pittsburgh Research Center (PRC) personnel conducted dust surveys at 13 longwalls operating throughout the U.S. and collected information to: identify current operating practices on these longwalls, identify the types of dust controls in use, document the levels at which these controls are being applied, and measure the respirable dust levels present. This data was analyzed to quantify the dust levels generated by the major sources on the longwall section and to evaluate the relative effectiveness of the control technologies in use.

Jan 1, 1997

By C. Don Sullivan

Paraphrasing the poetic repetition of Gertrude Stein - "Research is research, is research, is research --- ad infinitum." But research takes many forms and involves many facets. Perhaps the most simple of definitions is that attributed to the late "Boss" Kettering of General Motors who in advising a young trainee said, "Research is an intelligent effort to satisfy the curiosity of the human mind." Reclamation research is complex and requires a diversity of scientific knowledge. The overall aim of land reclamation research is directed to finding practical ways to develop efficient methods to restore mined lands to productive use, compatible with use of adjacent lands, as soon after mining as possible; and, finding practical ways to reduce or prevent damage to surrounding resource areas, which may be affected by the mining process. Research in the field of mined land reclamation is not entirely new, although in some respects we are exploring new areas each day.

Jan 1, 1967

The effect of the chemical composition of pulverized bituminous coal particles on their physical transformation during the initial stages of combustion has been investigated. The results suggested that cenosphere formation does not require extensive thermal decomposition of the coal particles. The vitrinites in the bituminous coal softened earlier and developed larger cenospheres than the othe macerals. The coal particles swell to a higher extent during combustion than in pyrolysis; however, the cenospheres formed in the former process experienced a higher extent of fragmentation. The development of microporosity occurred predominantly after the resolidification of the swelled char particles. The type of macerals originally in the coal did not significantly affect the microporosity of the chars. Conversely, the morphology and anisotropy of the chars were strongly dependent on the maceral composition of the coal.

Jan 1, 1986

By C. B. Manula

Languages such as SIMSCRIPT and GASP have reduced the programming skills required to build simulation models, but not to a level where these can be used by a busy engineer or manager unless he has extensive programming experience. In an attempt to make simulation a more readily available tool, Sanford (1969) structured a generalized materials handling model (UGMHS)* for underground coal mining. The majority of materials handling systems consist of a set of moves and a set of pieces of equipment required to execute the moves. UGMHS gives a technique for describing and classifying the elements in these sets and then a technique for simulating the interactions of these elements as the materials handling system operates. To apply the model, the user simply furnishes data parameters and a fixed set of orders to the computer for his own problem. This new philosophy of dynamic simulation as applied by UGMHS was demonstrated in the paper by Sanford and Manula (1973). A dynamic model of underground coal mining was presented for the purposes of systems design and selection of equipment for a completely new operation and the analysis of existing ones for possible alterations, additions, and general improvements. The main differences between this application and its predecessors is the ability to transport material from multiple mine faces to multiple mine destinations and the ready adaptability to a wide variety of mine layouts. The second difference that characterizes the model is the deterministic simulation of equipment moves according to their mechanical capabilities and the physical profile of the mining scheme. Here, the computer generates performance data in the absence of time studies to compare equipment rather than operator performance.

Jan 1, 1974