Search Documents

By Thomas H. Koenning

The number of spontaneous combustion incidents in the U.S. is expected to increase as the consumption of lower rank coals and the use of longwall mining becomes more prevalent. A spontaneous combustion incident holds the potential for substantial loss of life from a mine fire or explosion if not prevented or controlled at an early stage. Laboratory tests have been developed which are useful in ranking the susceptibility of various coals to spontaneous combustion. Ventilation circuits and mining methods can be designed to minimize the risk of spontaneous combustion. Early detection of spontaneous combustion is possible with the combined use of continuous monitoring, periodic gas sampling, and inspection.

Jan 1, 1989

By Joseph W. Mullan

The today status of air pollution control legislation and regulations can best be described as an exaggerated state of environmental limbo. The '70's began but one and one-half months ago yet it already has been very appropriately named "the decade of the environment." This certainly will be the decade for new legislation - new regulations and hopefully "Clean Air." Already Washington is faced with legislators playing "pollution politics" to the crowds. Students have redirected their efforts from Vietnam to the cleansing of the environment and everyone including the man on the street has become an environ¬mental expert. This is the decade we all face, but where are we today? Pollution is not a new problem. It has been with us for centuries and while much is left to be done, much has already been accomplished. I will try to make some comparisons of what I believe to be the good and bad points in the national air pollution control picture and hopefully will generate within each of you sufficient concern as to which comparisons are sound.

Jan 1, 1970

By T. Yun

The process automation of coal production is one of the important component parts for achieving the modernization of coal industry. To realize the coal mining process automation serves the significant, function of increasing productivity, improving the quality control of raw coal, making efficient use of mineral resources, saving energy and is of great importance in enhancing the safe operation and improving the labour conditions as well.

Jan 1, 1989

By Carl Erickson, James Hislop

INTRODUCTION As practiced today, longwall mining is a mechanical version of an established mining system. The equipment for longwall mining consists of four basic units: roof supports, face conveyor, winning or mineral-getting ma¬chine, and stage-loader conveyor. The system mines relatively thin slices of mineral across a predetermined face length in a virtually continuous sequence. As the winning machine cuts, the mineral is loaded automatically onto the face conveyor. In turn, the face conveyor is pushed over into the newly cut track by hydraulic rams attached to the conveyor and the roof supports. The roof supports then are lowered individu¬ally from the roof, advanced to the repositioned con¬veyor, and reset to the roof. At the end of the pass, the longwall cutter is pushed over, and a slice is taken in the opposite direction, so the system repeats itself. Fig. I illustrates a typical longwall mining system. The principle behind the longwall mining system is that the roof is supported only immediately adjacent to the worked seam, keeping the blocks of immediate roof clamped securely from the face to the rear of the sup¬ports. At the rear of the supports, the roof is allowed to fall and break up, with the swell of the broken material eventually establishing an equilibrium in the strata be¬hind the mined area. Fig. 2 illustrates the principle of longwall support. There are two distinct types of longwall mining. The longwall retreating system is the most common in the United States, South Africa, and Australia. The longwall advancing system is the most common in the re¬maining industrialized countries such as Britain, Ger¬many, Poland, and the Soviet Union. The longwall retreating system comprises a mining panel, where the roadways that form the head entry (end at which mineral is delivered from the face con¬veyor to a stage-loader conveyor) and the tail entry are predriven before the longwall units starts production. In the longwall advancing system, the longwall unit makes the head and tail entries as the face advances, utilizing various techniques to prevent the entries from being destroyed as they are left in a consolidating gob area. Fig. 3 illustrates the comparative approaches of the longwall retreating and advancing operations. As with most other underground mining systems, there are many variations on these two basic systems, using combinations of the systems that are dictated by

Jan 1, 1982

By J. B. Pateiro Fernandez, S. Möllerherm, E. Drüppel

"Since 1997 the Institute of Mining Engineering 1 at the Aachen University is dealing with the concept of sustainable development in the mineral industries. During this time it has conducted several research projects in this field. Its latest project is on the development of sustainability indicators for the German mineral industry. This paper describes some results of this project. A process chain analyses have been carried out identifying economic, social and environmental effects of the minerals extraction. Thirty indicators reflecting the particular conditions in the mineral industry have been designed. One important challenge was the design of quantifiable indicators taking into account the life cycle of a mining operation as well as mineral beneficiation and enrichment of the raw material."

Jan 1, 2005

By F. L. Wilke

Underground mining is a very complicated and complex industrial activity. The uncertain and, in most cases, the incomplete knowledge of the geological and mineralogical nature of the deposits can cause unforeseen difficulties. For a safe and uninterrupted operation, in addition to good planning and scheduling, reliable and up-to-date monitoring and control of all processes and conditions become necessary. Today, this is even more important in view of increasingly difficult working conditions, poorer grades, and more complex and expensive machinery. In short, large capital investment and higher risk of financial losses are involved in modern-day mining operations. Monitoring and control of the underground mining process has become a very complex and difficult task in itself. Many different systems are available, and the correct choice .is of utmost importance from both the economic and safety points of view. This chapter will deal with aspects of underground production monitoring and control. There are, however, many other areas of equal importance which are covered in an excellent manner in a hand- book by Olaf (1976) on monitoring and control of underground operations.

Jan 1, 1979

By D. S. McAllister, P. M. Rice, M. E. Fowler

The Westside Light Rail Project, a major 19.3-km (12-mile) extension of Portland, Oregon's light rail system, includes 4.6 km (2.8 miles) of twin 5.8-m (19-ft) diameter running tunnels, a binocular type station which, at 80 m (260 ft) below the ground surface, will be the deepest mass transit station in North America, two 9.4-m (31-ft) diameter station access shafts, and a 5.2-m (17¬ft) diameter ventilation shaft. The tunnels are being excavated by TBM and conventional rock, soft ground, and mixed-face methods. Geologic conditions, alignment, underground opening design, excavation method selection, and payment provisions for excavation and initial ground support are discussed.

Jan 1, 1995

By Randy J. Mikula

Cleaning of low-rank coals can have several meanings, depending upon the definitions of the terms "low rank" and "cleaning." In general, low-rank coals would be lignite or subbituminous according to the ASTM classification. For the purposes of this summary, cleaning is defined to be any process which materially reduces the proportion of inert material in the coal. For low-rank coals, this often means a reduction in moisture content since moisture is the major inert component in these coals. A brief discussion of conventional cleaning processes is included, as is an extensive reference list.

Jan 1, 1991

By J. A. Murray

Maintaining satisfactory air quality in electro-winning tankhouses has been problematic and costly, particularly as plant operating current densities have increased. Conventional approaches, including the use of beads, hollow spheres, surfactants and coalescer devices, have not proved completely effective, requiring that powerful ventilation systems be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses. The design, development, installation and cost of the new electrode cap system are described.

Jan 1, 1996

By Deepak Gupta, Brij M. Moudgil

Attempts were made to improve the recovery of coarse phosphate particles by adding selected frothers or precoated fine particles. A number of frothers for floating, specifically coarse coal and metallic minerals, were examined. Two of the frothers increased the flotation recovery of coarse phosphate by 3% on bench scale. Plant evaluation yielded improvements in overall phosphate recovery in the presence of these frothers. Addition of fine particles was also found to enhance coarse flotation under given conditions. Size, amount, and hydrophobicity of the fines added was determined to have a major influence on the coarse flotation efficiency. The grade of the product with and without frothers and particulate additives remained the same. Change in froth stability and viscosity are believed to be the primary reasons for enhanced recovery of coarse phosphate particles.

Jan 1, 1989

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation : "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining, the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers, etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables.

Jan 1, 1981

By Brian E. McGee

The Federal Coal Management Program represents the culmination of several years of effort by the Department of the Interior (001) to reformulate the manner in which coal owned by the United States is leased and developed. These efforts began in 1970 with a study by the Bureau of Land Management (BLM), which indicated that unless drastic changes were made in. the federal coal leasing procedures, federal coal lands would be leased almost for the asking while production of coal from those lands had been decreasing. Consequently, informal action was taken in 1971, which resulted in no further leasing being authorized until February, 1973. At that time, a formal moratorium on most coal leasing was established, with exceptions granted only for leases needed to satisfy short-term needs such as maintaining existing mines or supplying reserves for new contracts in the immediate future. This leasing policy embodied a long term objective of developing an entirely new planning system for federal coal leasing, as well as to schedule the preparation of a programmatic impact statement for this new system. As a result of the 1973 moratorium and the ensuing application of short-term criteria, only 10 federal coal leases (covering approximately 30,177 acres) were issued from February, 1973, through January l, 1976.

Jan 1, 1982

By M. R. Yalamanchili, C. A. Young, J. J. Kellar, W. M. Cross, J. D. Miller

Introduction Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available that allow direct in situ analysis of adsorbed layers. With reactive internal reflection elements (IREs), Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IR/IRS) allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar. 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Fig. I is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/dodecylsulfate, CaCO3/oleate, ZnS/xanthate and KCI/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990). Of particular interest to flotation chemists is the conformational behavior of the alkyl chain of adsorbed collector molecules. In the simplest sense, conformation can bethought of as the relative flexibility of the hydrocarbon chain caused by rotations about carbon-carbon single bonds. The flexibility is described by the amount of gauche/trans conformations in the alkyl chain. Figure 2 shows examples of gauche and trans conformations (rotational isomers or rotamers) in a hydrocarbon chain. These two conformations are observed when the terminal methylene groups in any four-carbon subchain are on the same side (gauche) or opposites sides (trans) of the plane of the middle carbon-carbon bond. A gauche conformer (rotamer) is thus a state of maximum potential energy, whereas a trans conformer is a state with minimum potential energy. The difference between these states has been found to be approximately 0.5 to 0.8 kcal/mole (Mead et al., 1986). The relative number of butane molecules present as gauche conformers with respect to trans conformers can be calculated from the Boltzmann equation (Mead et al., 1986). At 25° C approximately 66% of the butane molecules are trans rotamers. [ ] However at 100° C, only 33% of butane molecules are trans rotamers. Exposing the hydrocarbon chain to a polar, rather than an a polar, medium should also cause an increase in the number of gauche butylene groups in a hydrocarbon chain, although this effect has been difficult to observe experimentally (Mead et al., 1986). Forming a crystalline hydrocarbon is equivalent to decreasing the temperature, which greatly increases the amount of trans butylene groups present in the chain. From the preceding discussion, a picture of the solution species of concern can be developed. The collector monomer should exhibit the greatest number of gauche rotamers and most likely will look crumpled or balled-up to reduce the surface area in contact with water. The micellar form is expected to be aggregated, with the hydrocarbon chain existing in a less polar environment. These characteristic conformational features have been examined by FT-IR spectroscopy for various liquid phases of alkanoic acids (Umemura et al., 1981; Cameron et al., 1982a; Yang et al., 1986; Wong, 1987; Wong and Mantsch, 1983; Cross et al., 1992), phospholipid membranes (Fringe Ii, 1980; Casal and Mantsch, 1985: Wong et al.. 1988;

Jan 1, 1994

By John L. Halls

Modern business practice dictates that in order to ensure the economic optimization of investment, the size of any investment venture must be such that every increment of capital invested in such a venture yields at least a corporate minimum acceptable rate of return. This practice is based on the premise that alternative investment opportunities capable of yielding the minimum corporate return are immediately available. If a mining corporation is to make the maximum use of its investment funds, any capital investment in a mining property must comply with the above practice. The most important parameter in estimating ore reserves is the cut-off grade which is used to separate material into ore or waste. The cut-off grade is calculated on the basis that material of cut-off grade produces sufficient revenue to cover the estimated costs of mining and processing through to sales, including depreciation and produce a pre-determined profit. Ore reserves so estimated are adequate for determining the magnitude of an orebody but do not provide a sound basis for determining plant size and therefore capital investment in a new property or for expansion consideration on an existing property. From a financial analysis of this one ore reserve it is impossible to ascertain whether each increment of capital investment is providing the minimum acceptable rate of return, Other difficulties associated with the calculation of a cut-off grade including the determination of depreciation and the amount of pre-determined profit to be included in the cut-off grade calculation are outlined in the text. The proposed solution to determine optimum ore reserves and plant size for new properties avoids the complication of calculating a cut-off grade by computing a series of ore inventories using arbitrarily selected cut-off grades. A comparison of the cash flows generated by production from such ore inventories using incremental financial analysis clearly indicates the ore reserve and plant size which will best serve the corporation's investment and metal production goals. Incremental financial analysis of a corporation's operating mines and prospects assists management in assessing the comparative expansion and investment possibilities of each property for increasing or maintaining metal production on a long term basis.

Jan 1, 1969

By D. R. Zuchelli

The purpose of wrapping ball mills with thermal/acoustic blankets is twofold: 1) to maintain the desired temperature inside the mill, and 2) to reduce the sound emanating from the mill. This field case study focuses solely on the latter, evaluating and documenting the sound level reduction attributed to the installation of the blankets on ball mills and its potential to reduce the noise dose experienced by the process attendant. One of the three ball mills had already been treated (baseline) before the evaluation started. However, treating the remaining two mills still proved to be very effective, further reducing ball mill noise in the near field by as much as 10.0 dBA and producing far field noise reductions of 3.0 dBA or greater, extending as far as 35 feet from the mills and to the floor above. The model developed from the survey data shows that a process attendant spending a substantial portion of a shift in the mill building will experience a significant reduction in overall noise dose.

Jan 1, 2010

By John E. Young

United States Steel Corporation's Winifrede Mine is operated by Lynch District in the mountainous region of Eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slows which present both an opportunity and challenge in the design and selection of coal handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of underground haulage and, thereby, presented the opportunity to use high capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Winifrede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 feet from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede Mine coal handling facilities.

Jan 1, 1970

By P. A. Korpi

In March of 1978 the first set of Angular Spiral Liners utilized in grate discharge ball mills for wet grinding was put into service in the San Flanuel Concentrator of Flagma Copper Company. The use of these liners has decreased grinding media consumption by 19.2% and grinding energy consumption by 15.8%. In addition a 1.1% increase in grinding throughput is being realized through the use of the system. This paper describes the Angular Spiral Lining System and reviews the test program at the San Manuel Arizona Concentrator. Operating parameters are discussed in addition to the current testing program to futher optimize the system.

Jan 1, 1982

By Deepak Malhotra, William F. Riggs, Edward C. Dowling

INTRODUCTION Mining companies are In the business of making an acceptable profit on their Investments, It became obvious in the recent recession that economic profitability/viability depends on being the lowest cost producer In order to compete on a global basis. The burden of achieving this objective falls on the mineral manager. He must strive to produce a salable product in an environmentally acceptable process while continuously Improving the profit margln.(1,2) Metal prices fluctuate on a regular basis. They directly Impact revenue and hence operating philosophy. The mineral engineer needs to develop an optimum operating strategy to meet his overall objectives, One would expect that, In the modem era of complex computer models, it would be easy to develop an economic model to maximize profits and/or cash flow. Discussions with mill managers Indicate that one mine/corporation's optimum operating strategy is not necessarily optimum for another. This paper approaches the problems from basics "Economics 101" and Illustrates the complexity of developing a universal model which can be applicable to all mines. Case examples are used to illustrate the need for better communication to avoid the basic economic fallacy “that optimization of segments leads to optimization of the whole system.” TECHNICAL MODELS Technical models are a prerequisite to the development of economic models because they provide the necessary Input data to these models, The flow of material from a mine through the sale of the finished product is shown In Figure 1. The ore Is mined and milled, and the concentrate can be stored for sale or smelted and refined In-house or at a toll facility. The finished product(s) are held In Inventory until sold either through existing contracts or in the spot market. [ ] Fairly reliable technical models have been developed for mining, milling and smelter operations. Mine plans are developed to provide a good Indication of the relationship between production and cut-off grade. It is easier to change surface mine plans than plans for underground mines. However, there are limits to maximum production that can be achieved with existing equipment. It Is possible that mine benches may not be developed to handle additional equipment, even If It was purchased to enhance production. More often than not, the cut-off grade Is lowered to Increase throughput goals.

Jan 1, 1993

By B. Bergmark, O. Guyot, A. Broussaud, C. Bouché

The Boliden Aitik concentrator in Sweden processes 2,000 t/h (2,200 stph) of low-grade copper ore. The plant consists of five grinding lines that feed four bulk-flotation banks with a scavenger-concentrate regrind mill und a column cleaner circuit with a regrind mill. The authors installed a model-based expert optimizing control system to maximize copper recovery in the bulk-flotation circuit while maintaining an appropriate copper grude in the cleaner feed. The optimizing control system uses on-line assays and calculates and implements set points for cell pulp levels, air rates and reagent- addition rates. It combines the power of a dynamic population-balance model that estimates mineral liberation in each stream, an optimizer that computes appropriate set points and a rule-based module that implements the strategy. The benefits have been evaluated over a period of three months. The model-based expert optimizing control system generates a measurable increase in copper recovery, around 0.5%, and an optimized bulk-concentrate grade. The need to maintain the optimizing control system and other practical aspects are discussed.

Jan 1, 2000

By R. E. Cook

"Mineral deposits require substantial amounts of energy to transport and be processed into usable form and, as such, present a real processing challenge in that the deposits are never homogeneous and orebody compositional characteristics are all over the map. Extracting the desired mineral(s) from the deposit at sufficient profit margin, despite severe fluctuations in market price, requires process automation architecture capable of supporting an integrated enterprise solution. Such an architecture will encompasses the activities of individuals, process units, process areas, plant level activities, mine management and business planning, and accounting systems. Key to the automation process is the aspect of value generation. This article brings together the various requirements for the automation of a mining enterprise and presents the different aspects of how to obtain value across the entire mining operation.Minerals’ processing sites are historically long lived, with 20-year life-of-mine not uncommon and 75 years not unheard of. Considering that hardware technology advancements are introduced every six months, or less, it is prudent to select process automation systems that adhere to “open” industrial standards versus proprietary based systems. In the minerals processing industry, the key to survival is driving the cost of production per unit volume to the lowest possible level and provide enough profit to sustain operations. Control system architecture and business information technology are rapidly becoming important tools in the quest for productivity. Getting key dynamic business performance information at the right time to the right person or process unit is crucial to successfully achieving corporate goals. The process automation architecture selected must, therefore, be able to integrate to the various networking enterprises and business systems.The mining industry is generally known as an extractive industry that is physically oriented with respect to operations and the activities in which workers engage. Large numbers of people performing manual tasks in difficult surroundings, produce variable outputs. But times are changing – and so are industry best practices. While the nature of work still consists of activities such as ore extraction, ore movement, ore concentration, refinement and logistics, automation innovations are starting to change the nature of many of the production steps. The industry has transitioned from requiring more physical activities by workers to more information management, automated control and collaboration within the operation. Humans are good at situational intervention and nonlinear reasoning and do best when empowered with an overall production perspective. Machines and automation are good at repetitive functions, steady state operation, and managing transitions. Thus, a combination of advanced technology solutions, reliable and useful information and full human contributions are necessary to mining operations for value generation."

Jan 1, 2015