Search Documents

By I. E. Odom

A study was made of the physical and chemical nature of silica minerals found as natural impurities in bentonites and montmorillonitic Fuller&apos;s earth clay products as well as in <10 micron dust from eight processing plants. The results show that the silica minerals present in these clay materials are totally encapsulated or encased in clay. No "free" silica minerals could be observed in SEM images of either granular or powder products or in dust samples collected for MSHA crystalline silica analysis. Silica minerals, such as quartz, are identifiable by SEM and EDS analysis only after removing the clay coatings by vigorous washing. After washing it can be observed that all crystalline quartz grains also have diagenetic overgrowths of what is probably opaline silica. The clay and opaline silica encapsulation of quartz plus the strongly hydro scopic nature of montmorillonite are believed to be responsible for there not being a single confirmed case of silicosis among workers in the subject plants after more than 65 years of production.

Jan 1, 1996

By D. J. A. Chambers, J. M. Wempen, K. D. Koper, M. K. McCarter, K. L. Pankow

"The EarthScope Transportable Array (TA) of broadband seismometers (www.usarray.org) was deployed across southwest Wyoming from November 2007 through May 2009. During this time period the Array Network Facility (ANF, anf.ucsd.edu) detected and located a total of six seismic events near the trona-mining district. This lack of seismicity is atypical compared to coal mines employing similar mining methods. In this study, eighteen months of continuous seismic data from several nearby TA stations are reexamined using conventional and correlation-based methods to detect seismic events. Waveform cluster analysis and epicentral locations are used to discriminate between mining induced seismicity (MIS) and seismic energy generated from surface blasts at nearby coal mines. The locations and magnitudes of the 143 newly detected MIS events are compared to regional subsidence as measured by Differential Interferometric Synthetic Aperture Radar (DInSAR). INTRODUCTION An abundance of natural resources and a favorable political climate have made southwest Wyoming home to multiple large mining operations. Among these operations are five underground trona mines located approximately 50 km west of Rock Springs, Wyoming. The trona mines employ room and pillar, longwall, and solution mining methods over an area roughly 900 km2, and produce a sizable portion of the world’s soda ash (Brown 1995). Historically, in the Rock Springs mining district, several relatively large magnitude seismic events have occurred. These events are thought to have been related to mining activity and have caused notable subsidence (Case 1997). The largest event in the region recorded by seismometers, ML 5.1, has been confirmed as the 1995 Solvay Trona Mine collapse (Pechmann et al. 1995). In addition, blasting at surface coal mines near Rock Springs produces significant amounts of seismicity; approximately 50% of all daytime seismic events in the Mountain time zone from 2007 to 2009 locate near an active surface mine in this region (Astiz et al. 2014). Much of the current research related to surface subsidence and induced seismicity focuses on wastewater impoundment (Ellsworth 2013) and hydraulic fracturing. The observable seismicity in geological injection environments is widely variable and McGarr (2014) has argued that, in such environments, the maximum amount of seismic energy that can be released is proportional to the injected volumes. Like injection environments, in extraction (mining) environments seismicity is highly variable depending on many geological and operational variables (Boltz et al. 2012; Carnec and Delacourt 2000; Fritschen 2010; Iannacchione et al. 2005; Sen 2013) and does not always correlate well spatially with subsidence, a surface expression of extraction at depth."

Jan 1, 2015

By Kevin Andrews, Zach Agioutantis

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

By Ryan Marsters, Adam Pring, Robin Dornfest

Raw water supply in the central Rocky Mountains often relies on trans-basin conveyance. Many of these older diversions incorporate high-elevation, miles-long tunnels driven over a century ago in hard rock. Tunnels were excavated using conventional drill-and-blast mining and weak ground was supported by timber sets and other various means. Over time, timbers rot and fail, rock quality deteriorates, and the timbers are gradually replaced by more timber, steel patches and braces, formed concrete, rock bolts, split sets, shotcrete, and other means which are commonly applied over existing support, thereby reducing tunnel cross sections, obscuring previous support systems, and rarely addressing the failing rock itself, leading to further deterioration of both the rock and the existing support. Traditional investigation techniques to assess compromised areas are often unfeasible due to access, depth, rubble and voids behind weight-bearing existing supports, confined space, poor invert conditions, poor ventilation, and flowing water. This presentation will discuss design procedures for assessing obscured ground conditions, assigning support classes which accommodate for unknowns, and implementing contractual means to address inevitable surprises or quantity overruns. Case studies include raw water supply tunnels in the Rocky Mountain region constructed between early to mid-20th century.

Dec 1, 2022

By C. N. Bensley, S. K. Nicol, R. Lamb, G. W. Kidd

Flotation circuits in the metalliferous industry recover high value concentrates from very fine (minus 0.lmm), low grade, slow-floating feeds. Flotation columns acting as final cleaners within these circuits offer the benefits of higher grade concentrates, reduced circuit complexity, improved control and reduced power consumption. By contrast, in the coal industry, these benefits have not been realised, principally because columns are not well suited to the treatment of conventional coal flotation feeds (minus 0.5m). However, this does not imply that columns do not have a place within the coal industry, rather that they must be applied in a role where all the unique advantages of column flotation can be of benefit. The development of a commercial scale column to recover discarded ultrafines from the Riverside preparation plant of BHP-Utah Coal Limited is discussed. Particular emphasis is placed on the column design features pertinent to the recovery of ultrafine coal. Pilot and commercial scale column performances are compared. The results of the commercial scale testwork indicate that a full installation at the 5.5 MTPA Riverside plant would annually recover additional coal worth $US 6.6M.

Jan 1, 1988

By D. D. Harbuck

The U.S. Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent such as 502 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage counter-current leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with 502 or sulfuric acid.

Jan 1, 1991

By Swan. J. D.

Repairing and replacing equipment damaged by corrosion and abrasion is a major cost throughout industry, especially in the coal mining industry. Careful study of corrosion and abrasion, and their causes and effects, often leads to the selection of alternative materials which can provide economies. What, actually, are corrosion and abrasion and how do they contribute to the cost of operating a coal-preparation plant? Furthermore, what can be done to alleviate corrosion and abrasion problems and thereby reduce operating costs? These questions will be answered in the following discussion, which will describe the destructive action of corrosion and abrasion and give several methods for controlling corrosion and abrasion losses, These methods include the substitution of stainless steel for carbon steel, the use of corrosion inhibitors, and the use of design to eliminate corrosion and abrasion. Examples will be given illustrating the benefits that have resulted in plant tests when these methods of controlling corrosion and abrasion were used.

Jan 1, 1970

By Shiou-Chuan Sun

Notwithstanding the fact that unsaturated fatty acids are used in preference to saturated acids for most flotation purposes, information regarding their collecting properties is sketchy. Keck, Eggleston, and Lowry1 reported in 1939 that the collecting power of fatty acids on hematite decreased in the order of oleic, lauric, myristic, palmitic, and caprylic acid. Keck and Jasberg2 described in the same year that "unsaturated oleic acid with 18 carbon atoms was a better collector than saturated stearic acid" for floating magnetite. Gaudin and Cole3 stated in 1953 that the double bonds of oleic and linoleic acid were not oxidized during the flotation of fluorite, whereas the double bonds of linolenic acid were measurably altered even after one single flotation step. In August, 1953, Hukki and Vartiainen4 concluded that the collecting power of palmitic, oleic, linoleic, and linolenic acids on ilmenite, magnetite, pyrite, and rutile increased with an increasing number of double bonds in the acid molecules. This was subsequently proved to be generally true for the flotation of mapganese5, phosphate6, and magnetite7. The above cited literature indicates that, prior to the present paper, only about ten minerals were tested with pure unsaturated fatty acids as collectors.

Jan 1, 1959

By R. L. Grayson

A goal programming-based worker scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model the accomplishment of each regular and non-regular job is a goal. The objective is minimization of the deviations away from the goals. A number of coefficients are used as premultipliers of the decision variables in order to address practical considerations associated with the utilization of workers and the requirements of jobs. Some of these premultipliers will be updated expertly within MMSS, timely updating the statuses of the dynamic parameters.

Jan 1, 1991

By James A. Jessop

The Bureau of Mines is investigating the use of geophysical methods to determine rock mass characteristics, particularly rock quality, lithology, and fracture parameters that are important for determining the feasibility of in situ leaching operations. As part of this research, two Bureau-developed crosshole geophysical systems are described that can be used for site investigation and rock mass characterization. Results are given for performance tests at field sites in Arizona and Texas and for correlations between the crosshole seismic data with fracture frequency, rock quality, and lithologic variation. Recommendations are made for using elastic waveform propagation characteristics and dynamic elastic properties for improving rock mass characterization in the geomechanical assessment of in situ leaching deposits.

Jan 1, 1990

By K. F. Unrug

Martin County Coal Corporation is located in Martin County, Kentucky in the Appalachian coal fields, near the West Virginia border. The total leasehold covers more than 33 000 acres. Total annual production at Martin County Coal Corporation is currently 2,500,000 tons, but in certain years exceeded 3,000,000 tons. Approximately 45 percent of the annual production comes from two surface mines. The balance is produced from five underground mines. Martin County Coal Corporation&apos;s work schedule consists of 240 days/year, two nine-hours shifts/day.

Jan 1, 1991

By J. Fritz, V. Gangrade, J. Briton, K. M. Ajayi, M. L. Harris, G. Cole, M. Young

Mine workers using diesel-powered equipment experience the highest occupational exposure to diesel particulate matter (DPM). This problem could be aggravated in underground stone mines due to their unique ventilation challenges with the large openings for airflow. Hence, adequate ventilation in these mines requires a combination of effective ventilation planning and delivering needed air quantities using auxiliary fans and stoppings. To meet this challenge, the National Institute for Occupational Safety and Health (NIOSH) developed the Air Quantity Estimator (AQE) software as a mine planning tool to help underground mine operators estimate the air requirements necessary to dilute DPM in the main air stream to statutory levels. The major parameters required for the calculations are the engine’s horsepower, DPM emission rate, the percentage operating time, catalytic converter efficiency, and filter efficiency. In efforts to provide major updates to this software, this study describes the recent development of a revised version of the Air Quantity Estimator (AQE 2.0). With the revised version, users have access to a comprehensive database of over 40,000 pieces of equipment, can define their specific target DPM level, and can create specific equipment for a customized database, in addition to having an improved easy-to-use interface. The software output provides an estimated total airflow necessary to dilute DPM based on the projected emissions, and the user can generate a related results report. The results also provide the mine personnel with a tool to identify vehicles that are high DPM contributors and could further be used to optimize the ventilation requirement by making changes to the percentage operating time of the engine. This software provides the mine with a user-friendly tool that could help reduce the DPM exposure of workers.

Feb 1, 2023

By E. H. Cho

An acid mine drainage sludge sample containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn was obtained from the central part of West Virginia and leached with sulfuric acid at pH 3 and at room temperature. Air was bubbled through the leach solution to precipitate the iron content from the solution at pH 4.5. The leach solution contained 258ppm Zn, 105ppm Ni, 90ppm Co and 2050ppm Mn. Three distinctive solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA, Cyanex 272, and then Lix 84. The AIO ratio was 1 and the extractants were diluted 10 times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to pH 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1993

By Jose F. T. Agapito

The mining engineer must be able to predict the structural behavior of the rock around underground openings so that he can answer questions relating to safety and economics. With the present status of rock mechanics knowledge, exact predictions cannot be attained and approximate idealizations are made. As a first approximation, structural design makes use of theory, laboratory testing of rock properties, and available experience from excavations in similar rock formations. However, realistic design can usually be obtained only after in-situ observations and measurements are made. After all the information is collected, judgement and experience play a most important role in the final formulation of the design. This paper describes part of a geotechnical program which was instrumental in obtaining information for the design of large oil shale pillars. The work was carried out during 1971 and 1972 in the experimental mine of the Colony Development Operation. Colony is an oil shale venture formed between Atlantic Richfield Company, Operator, The Oil Shale Corporation, Cleveland-Cliffs Iron Company, and Sohio Petroleum Company to conduct research and development in mining and retorting of oil shale, The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 250 miles west of Denver (Figure 1) . Mining was conducted by the room-and-pillar method in a 60-ft high portion of the Green River Formation at a depth of 600 to 850 ft, Pillar dimensions are approximately 60 ft by 60 ft. The mine site is in the eastern face of the canyon containing the Middle Fork of Parachute Creek, The distance from the mine to the side of the mountain varies from 500 to 1,200 ft, and its height above the stream floor is approximately 700 ft.

Jan 1, 1974

By Cary Hirner, Sarah Lothman, Chris Mueller, Savita Schlesinger, Mike Hanna, Ian Fitz-James

Loudoun Water is currently implementing a quarry to reservoir conversion that will improve water supply reliability in periods of drought and flexibility in water supply operations when turbidity in its Potomac River supplies are high. The Milestone Reservoir Project consists of an inter-tie to the existing Potomac River Pipeline; new pipeline and tunnel; and a pumped intake and outlet works. Planned construction involves significant risks due to underground conditions which includes hard, igneous rock and high groundwater at the creek crossing. In addition, the site is constrained by Goose Creek, an adjacent residence, active mining in a quarry next to the new reservoir, public use of adjacent park space, and the Washington and Old Dominion Trail. Working with these constraints will require close coordination with active mining operations and public and private property owners. Safety of personnel involved with construction also represents a concern with quarry high walls over 30 meters in height near the planned construction. In consideration of key projects risks, Loudoun Water determined that an innovative CMAR delivery approach provided the best opportunity to achieve its goals in quality, innovation, front-end cost and schedule certainty, and operational flexibility and reliability. What matters most to Loudoun Water is the value in having a builder participate in the design process where key decisions can be made based on consideration of risks, cost, schedule, quality, and operability and maintainability of the system. While a progressive design-build delivery model may have produced similar outcomes, Loudoun Water had already invested in substantial development of the design for the work, and ultimately, CMAR provided Loudoun Water the opportunity to retain the partnership with the design team while gaining valuable input from a contractor. Among the challenges with CMAR in the Commonwealth of Virginia is a substantial limitation on self-performance corresponding to 10 percent of the construction value of the work. A significant industry outreach program was initiated by Loudoun Water to encourage participation with incentives in contract terms that allowed for the CMAR Contractor to make a reasonable profit. This paper reviews the CMAR procurement process and discusses contract incentives that were adopted to promote the work within the constraints of contract law in Virginia.

Jun 13, 2021

By R. Raymond

The occurrence and distribution of organic sulfur in coals may be investigated using electron probe microanalysis, scanning electron microscopy, and optical petrography. A general relationship exists between macerals and organic sulfur contents in individual coals: sporinite, resinite = micrinite, vitrinite > pseudovitrinite = semifusinite = macrinite > fusinite. With increasing organic sulfur content of a coal, the total range in organic sulfur content between macerals containing high and low organic sulfur contents likewise increases. Furthermore, the organic sulfur content of the vitrinite in most coals equals the organic sulfur content of the coal. For any individual coal, organic sulfur contents of macerals correlate inversely with reflectance-in-oil measurements, but the amount the organic sulfur contents vary between macerals cannot be calculated based solely on the coal&apos;s rank. Formation of pyrite following peatification has no effect on organic sulfur contents of surrounding macerals.

Jan 1, 1986

By Richard C. Mayberry

Phosphate reserves have been and still are a controversial subject. Some published estimates are particularly conservative and have caused concern in government and political circles that southeastern phosphates are a dwindling resource. "Ores and ore bodies" are a function of economics that relate to a time/demand factor. The history of phosphates and other mineral commodities is one of mineral deposits (resources) ever becoming ore (reserves) via a long term logic based on price, supply, and demand factors operating through time and improved technology. Projections indicate that southeastern phosphates are sufficient for several centuries of operations at present production rates.

Jan 1, 1981

By Roy A. Grancher

?The Horn of Plenty seems to have sprung a leak?.? anonymous For the first time in the Nation&apos;s peace-time history, shortages have become a way of life for the United States. Such words as scarce, tight, and critical are used in regard to supply, leading to priorities, allocations, and possible rationing as make-shift attempts to satisfy demand. Almost every day a new type of shortage appears in another product area that has traditionally been taken for granted as being in perpetual abundance. The range of coverage extends from basic commodities such as oil, chemicals, cement, steel, copper, cotton, etc., through to machine tools, motors, bearings, electronic components, etc. , to those finished outputs that satisfy our fundamental requirements for food, clothing and shelter. Signs of the times appear in cancelled airline flights, unfilled lines at gasoline stations, no available home freezers, lengthy delays in any furniture deliveries, or to that little old lady seen walking out of a local supermarket clutching her hoard of twenty rolls of toilet paper. What a sad commentary to have to make about our Land of Plenty, so long the envy of the World for its material wealth -- and today with its initials "U. S." seemingly standing for ?Unlimited Shortages.?

Jan 1, 1974

By Sidney M. Cohen

[Portland cement is a product made from a combination of limestone and argillaceous material which would supply the necessary amounts f calcium, silica, alumina and iron to form cementious compounds when fired at high temperatures. The resulting mixture, usually around 80% limestone and 20% argillaceous, is ground nine (80% -200 mesh), blended and then fired1 (2600-2700°F) to produce a cement clinker from which the final cement product is produced by grinding. The argillaceous component can be shale, clay, slate or other sources of the individual components of silica, alumina and iron. This paper deals with a case where a clay component was under consideration. The planned Plant site was to be located at a well defined limestone deposit. When it came to the argillaceous component, the nearest uniform deposit of clay was over 50 miles away and would require purchase of land or clay from the owner plus the daily delivery costs to the plant site. This situation made the plant site economically questionable. It was decided that a local clay deposit, which was available at the plant site but was orginally not considered due to lack of chemical uniformity and its high free silica content, would be reconsidered.]

Jan 1, 1983

By J. A. Herbst

It is widely recognized that Semiautogenous Grinding (SAG) circuits require the use of effective process control techniques to achieve their full processing potential and to protect them from the harmful effects of overloads and grind-outs. This requirement is even more essential as the variability of the ore being processed increases. The new Chino Mines Company concentrator located near Santa Rita, New Mexico started operation in June of 1982. At least eight major rock types are mined and milled. Ore hardness, feed size, and specific gravity are quite variable. Typical feed rates per grinding line are 850-900 tph but extremes of 260-1200 tph have been encountered. Normal feed rate variations of between 400 and 1100 tph are encountered on a weekly and sometimes daily basis. Feed size varies with rock type from a maximum of eight inches for the harder ores to two inches for the softer ores. One somewhat unique characteristic of the Santa Rita ore body among major copper mines is the wide variation in ore specific gravity. Specific gravities of the major rock types range between 2.7 and 3.6. The specific gravity variations are due to large changes in magnetite concentration throughout the pit. The result of this is large variations in SAG mill throughput which can have a harmful effect on downstream ball milling and flotation performance. Due to these wide fluctuations in ore characteristics, it was recognized soon after startup that successful operation of the grinding circuit and the plant at large was dependent upon the development of an effective automatic grinding control strategy. Research at the University of Utah has suggested that control based upon critical but difficult or costly to measure variables would improve automatic control performance. A project team made up of the Chino process control staff, Kennecott&apos;s Process Control department and the University of Utah Metallurgy Department was established to assess these concepts at Chino. This paper describes the development and on-line plant implementation of an Extended Kalman Filter that uses simple models of the SAG milling process, to predict the volumetric loading, the rock mass, the water mass, and the ball mass within the SAG mills at Chino. The on-line estimation of these parameters is the first step in the development of an integrated SAG mill/ball mill control strategy which is hoped to L eventually maintain the grinding circuit at its maximum capacity, while balancing the grinding load between the SAG and ball mills. Examples of long term estimation with the models and filter are shown for typical operating conditions as well as a SAG mill overload and grind-out.

Jan 1, 1983