Search Documents

By H. R. Batchelder

Much information on oxygen production and the manufacture of synthetic liquid fuels has been published during the past several years. From time to tine the investment and operating cost of oxygen plants of various sizes has been estimated. Surveys have been made so that the various processes by which oxygen is produced commercially might be compared. The gas-making processes in which oxygen is employed, which wore used in Germany during the war, have been described in T.O.M. reels, and this information has been published. Descriptions of pilot-scale or proposed commercial plants for the production of synthesis gas or hydrogen and their conversion to synthetic liquid fuels also have been published. In general, each of these publications has dealt with a particular phase of the over-all problem. The present paper will discuss the relationship between these phases: The factors that affect oxygen manufacture and costs, the methods for the use of oxygen and for the production of synthetic liquid fuels, and, to some extent, the economic factors that must be considered.

Jan 1, 1951

The latest Active List of Permissible Explosives and Blasting Devices was published in July, 1929, as Bureau of Mines Report of Investigations 2947, 2 under the title or "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1929.' Subsequent Reports of Investigations 2253, 2958, 2962, 2972, 2988, 2992 and 3000, were issued to record the official actions taken during July, August, September, October, 1929, and January, February, and March, 1930. No changes were made during November and December, 1929, and April, 1930. The following additional changes in the list recording the actions taken during May, 1930, are now authorized. [ ]

Jan 1, 1930

By L. A. Neumeier

The Bureau of Mines evaluated creep and other properties of extruded Zn-30 pct-AI alloys containing 0 to 0.7 pct Mg. The alloys were extruded both above and below the Zn-Al eutectoid temperature of 275° C. Creep behavior is defined for the alloys as extruded and after various heat treatments. Tensile properties, hardness, thermal expansivity, impact resistance, and microstructures are given. The alloys, either with or without magnesium, required substantially less pressure for extrusion near 275° C than at higher or lower temperatures. The alloys containing magnesium exhibited significantly greater hardness, tensile strength, and creep resistance, but much lower ductility than the 2n-30 pct Al alloy. The properties were very sensitive to the processing conditions.

Jan 1, 1971

By Barry W. Klein

The performance of the U.S. economy in 1977 was similar to that in 1976 which, in turn, had been a considerable improvement over 1974-75. In 1977 real gross national product (GNP) showed a similar, but some-what slower, growth pattern compared with 1976. Real GNP increased sharply in the first quarter of the year followed by smaller increases for the remaining three quarters. With only two exceptions, the monthly unemployment rate declined or remained steady throughout 1977, falling to a low for the year in December. The inflation rate in 1977 was slightly higher than in 1976, but the rate still remained far below that of 1974-75. Total U.S. output as measured by GNP in current dollars rose 10.8% in 1977. Real GNP in constant 1972 dollars increased 4.9%, and inflation, as measured by the implicit price deflator, rose 5.6%. In real terms, gross private domestic investment for residential structures increased 19.3% in 1977, only slightly below the 22.9% rise in 1976; State and local government expenditures increased 1.1 % in 1977; and personal consumption expenditures for services rose 4.5%.

Jan 1, 1980

By Charles L. Kimbell

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in the country and regional reports that comprise the five other sections of 1991 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible, without the efforts of the personnel of national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, appreciation is expressed to the multitude of persons employed by these agencies.

Jan 1, 1993

By K. P. V. Lei

An electrochemical process was developed for the preparation of vanadium from vanadium carbide. Commercially available vanadium carbide (V2C) was used as the starting material. Vanadium was obtained by electrolysis of the V2C in a BaCl2-KCl-NaCI-VCl2 electrolyte at 670° C using a helium-atmosphere, molten-salt electrolytic cell. Vanadium products were recovered with purities high as 99.6 percent. Current efficiencies of 87 percent and vanadium recoveries of 84 percent were attained. The cathode products were amenable to electrorefining to high-purity vanadium of 99.96-percent purity.

Jan 1, 1971

By R. D. Leitch

Tests have recently been conducted by the Bureau of wines on the ignition hazard of exposing heated filaments of electric mine lam bulbs in an explosive mixture of methane and air. This investigation was undertaken in order to settle a question that had arisen in connection with the safety of miners? electric lamps. For several years, in view of former studies made by the Bureau and reported in Bulletin 524, the fact that the heated filaments of even low voltage, lour candlepower bulbs constitute a danger was generally accepted by the Bureau's engineers. These early tests, as well as subsequent tests, were conducted with Pittsburgh natural was as the testing medium.

Jan 1, 1925

By P. Kovalchik, S. Peng, G. Cole, R. Matetic

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90 percent of coal miners and 49 percent of metal/nonmetal miners had a hearing impairment by age 50 (Franks, 1997). Mine workers are exposed to additional noise levels underground due to the reflection of machine-generated noise that would otherwise dissipate in an aboveground setting. Determining the sound-absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed rather than being reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes a finite room, a diffuse field and a relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper presents a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients are essential for determining and predicting potential overexposure to machine operators in different mine environments.1

Experience, it is said, is the best teacher. Some experiences, however, should be shared so that no one else will ever have to live through them again. The fire at the Sunshine Mine is one such experience. ?Hard-rock mines don?t burn.? The Sunshine Mine near Kellogg, ID, was the nation?s premier silver producer for many years. In 1972, the mine was nearly 6,000 feet deep, contained hundreds of miles of worked-out areas, and employed nearly 500 people. Because of its depth and the type of host rock for the silver (unburnable quartzite), the general thinking of the day was that fires in mines such as the Sunshine were impossible, because ?hard-rock mines don?t burn.? What wasn?t really considered was that timber supports, foam insulation, and mining equipment do burn and that the carbon monoxide gas produced by burning is far more deadly than fire itself. Thus, no one was prepared when, on May 2, 1972, a fire of un-known origin broke out below the 3100 level of the mine. Before long, 173 miners on the day shift were trapped by thick, black smoke. By the time the fire was out, 91 miners had died, and the Sunshine Mine Fire became known as one of the worst mine disasters of the 20th century. It became the catalyst for passage of the Metal/Nonmetal Health and Safety Act of 1977, which applied the same federal safety standards to hard-rock mines as those regulating coal. Mandated safety training, mine inspections, and equipment standards were brought into force.

Aug 1, 2002

By J. Burlin Johnson

In small-scale blasting experiments conducted in the Bureau of Mines laboratory, small charges were used to produce craters in blocks of concrete mortar. The results are compared with larger scale experiments of other research workers, and the comparison demonstrates the similarity of the results obtained and indicates that small-scale blasting should be a useful tool for predicting large-scale blasting effects. INTRODUCTION The purpose at this investigation was to conduct blasting experiments in mortar in the laboratory and then, by comparing the results with those from larger scale field blasts in rock to determine to what extent, if any, the laboratory results resemble those in the field. The work described herein was the initial phase of a project aimed at evaluating small-scale blasting as a tool for use in improving blasting techniques. It is evident from the stand-point of control and cost that small-scale blasting would be valuable in the study of rock fragmentation by blasting in mines and quarries, if the extrapolation is valid.

Jan 1, 1962

By D. R. Flinn

The Bureau of Mines has studied the electrochemical parameters important to the preparation of coatings of the platinum-group metals. Using molten mixtures of sodium and potassium cyanides in an inert atmosphere, techniques have been developed that permit the preparation of baths for platinum, rhodium, and iridium electrodeposition. Cyclic voltammetric and slow sweep rate linear polarization techniques have been utilized to determine optimum potential and current values for preparation of plating baths and for the electrodeposition of coatings. Techniques are described for the deposition of platinum and rhodium coatings at near 100 percent anode and cathode current efficiencies, and for iridium at approximately 80-percent efficiency. Palladium deposition from these molten cyanide baths remains un-satisfactory. The chemistry of the palladium-containing cyanide bath is discussed. Examples of scanning electron microscope photomicrographs of typical platinum coatings are presented. Techniques are described for the preparation of platinum coatings on large objects.

Jan 1, 1982

To pinpoint dust sources and to improve dust control on longwalls. Approach Use short-term gravimetric sampling to determine the severity of various dust sources, and to evaluate dust control techniques used in longwall mining. Short-term gravimetric sampling can be used to isolate dust levels produced by various dust sources. How It Works Traditionally, gravimetric samples have been collected over an 8-hour shift, yielding time-weighted, average dust concentrations. This method gives a good indication of the full-shift respirable dust exposure of underground workers, but is less than satisfactory for identifying dust sources, determining their severity, or for evaluating the effectiveness of dust control techniques. Short-term gravimetric sampling uses equipment available to all mine operators. Two individuals composing the survey team each collect multiple (three to four) gravimetric samples during selected segments of the mining cycle. Multiple samples are necessary to insure accuracy, and to obtain a valid average measurement of the respirable dust concentration when sampling for short periods of time (typically 20 to 30 minutes). The gravimetric instruments may be carried in a sampling package or in a "sampling vest." A fishing vest with four large pockets can be used for this purpose. The sampling pumps are carried in pockets and the sampling head assemblies arc hung across the front of the vest.

Jan 1, 1982

By R. L. Brown

This report, the seventeenth in an annual series, summarizes Bureau of Mines research and technologic work on coal and related investigations for July 1, 1951, to July 1, 1952. It 1s based largely on publications issued during the fiscal year, although 10 some instances data are presented that have not been published previously. Footnote references are given to the publications so that further details on the work may be obtained. Bureau of Mines research on the mining, preparation, and utilization of coal is directed toward developing and encouraging safer and more efficient mining practices and preparing and utilizing coals to the best advantage.

Jan 1, 1953

Continuous remote sensing of methane concentration in underground mines. Approach A methane transducer, developed as a fixed point rib-or face-mounted operating device, measures ambient levels of methane and produces a signal that is proportional to the measured concentration. How It Works The methane transducer, developed under contract for the Bureau of Mines, uses a catalytic-type sensor which will detect methane concentration. The transducer is mounted vertically, as shown. This type of mounting minimizes dust accumulation on the sensing element, which might cause degraded operation. The unit must not be located in an area where water can continuously drip or run on It. The transducer generates an electrical signal proportional to methane concentration at the sensor. A sensor failure output indicates the status of the sensing element A circuit within the methane transducer detects whether the sensing element is shorted or open. A high signal (approximately 8 Vdc) on the failure output Indicates the sensor element is operating In Its normal range. A low output (less than 1 Vdc) indicates an element fault. The methane transducer, enclosed in a stainless steel

Jan 1, 1982

By J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 3S0 meters (1150 ft.) and 488 meters (1600 ft.). The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broadband, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or F layers of ionosphere as an upper plane and the earth as a lower plane.

Jan 1, 1974

By C. H. Elder

Coal degasification boreholes drilled from the surface have been success-fully hydraulically stimulated to increase the flow of gas from the coal. This Bureau of Mines report describes the hydraulic stimulation procedure for a coalbed, the equipment required, and design criteria for the treatment. Three examples of stimulation treatment show from fivefold to twentyfold increases in gas production. The tests were conducted in the Pocahontas No. 3 coalbed, Buchanan County, Va., the Pittsburgh coalbed, Washington County, Pa., and the Mary Lee coalbed, Jefferson County, Ala. Two sites where the coal was hydraulically stimulated and exposed by subsequent mining show no adverse effect on mining operations through the treated zones. The induced vertical partings were confined to the coalbed and did not in any way affect either roof or floor rock.

Jan 1, 1975

By James H. Russell

The Bureau of Mines, U.S. Department of the Interior, in cooperation with the Department of Energy, has attempted to increase the activity of nickel catalysts for converting synthesis gas, derived from coal, to a substitute natural gas. This report describes the effects of low-level additions of B, Ca, Ce, Co, Mn, Mo, Pd, Re, Ti, Y, Zn, and Zr on the methanation activity of Raney nickel. The methanation rate at 320° C and the resistance to poisoning by 2 ppm H2S were used to compare catalysts. The effects of the additions were small, and the experimental variances were large, necessitating the use of statistical methods to identify significant effects. Co, Ti, Y, and Zn improved the resistance to H2S poisoning, but only Co improved the methanation rate In some individual catalysts containing Ca, Mo, or Mn, both the methanation rate and resistance to H2S poisoning were improved.

Jan 1, 1980

By J. R. Hoskins

A recent survey of 23 vein-type metal mining operations in several western states discloses that some of the more serious deficiencies in ventilation technology are associated with inordinately high levels of mine resistance. This problem has progressively increased over many years of operation (without adequate remedial action) as mines have become extended in depth. Where two shafts form the downcast and upcast airways of a relatively deep mine, the whole of the mine air volume must pass through each shaft in turn. Since at least one of these shafts contains hoisting equipment, structural members are necessary to support the rigid guides and shaft walls. These offer high aerodynamic resistance. In some deep mines, a single shaft of this nature may represent upwards of one-half of the total mine resistance. The second shaft, depending upon its design, may represent an additional one-third of the mine resistance. Therefore, the various working levels throughout the mine contribute only the small remaining amount of the total mine resistance.

Jan 1, 1972

By Ivan F. Avery

DOMEST1C production of carbon black in 1963, remained at about the same level as in 1962. Carbon black produced by the furnace process increased 2 percent to 1,880 million pounds in 1963 and accounted for 91 percent of the total output. Channel black production continued to decline and was 14 percent less than a year ago. Shipments during 1963 totaled 2,098 million pounds, a 1 percent increase for the year. An increase of 88 million pounds in domestic sales was partially offset by a decrease of 72 million pounds in carbon black exports. Total value of carbon black production in 1963 was $148 million. The average value per pound was 7.18 cents or 0.12 cent per pound more than in 1962.

Jan 1, 1964

By William H. Schiffbauer, William D. Mayercheck, August J. Kwitowski

This report summarizes work sponsored by the Bureau of Mines in the development of a remote operating system (ROS) for controllng a thin-seam continuous miner (TSCM) 500 feet or more distant from the extraction face. Detail s are provided on ROS subsystems including the continuous miner, video equipment, controls and displays, the electronic control system, and the operator station.