Search Documents

By John Nagy

Large-scale tests in the U.S. Bureau of Mines Experimental Coal Mine show that the explosion hazard of coal dust on shuttle-car roadways can be con-trolled by proper application of water, dry rock dust, a saturated solution of ammonium phosphate, or mixtures of water or the water-phosphate solution with rock dust. The experiments were made with loadings of 1.0 and 5.0 pounds of mine size coal dust per linear foot of entry, and with a 3-or 4-inch-thick layer of coal rubble on the floor, The data from the tests with mine-size coal and rubble are comparable. The water contents of the dust loading were determined from samples collected just prior to initiation of a gas-air mixture in an ignition zone at the face Dust samples were collected 1 inch deep from the coal-rubble deposit. One experiment was made with the dust in the coal rubble bound with latex applied as a water solution by spray. The binding action was inadequate and explosion propagation was obtained.

Jan 1, 1970

By Welby G. Courtney

The Bureau of Mines conducted a field test program in the Pittsburgh coal seam to investigate the effect of water sprays in the suppression of respirable dust being formed while cutting with a continuous-mining machine. Emphasis was given to the location of spray nozzles on the top and bottom of the cutting boom. Results showed that (1) sumping caused about 60 percent of the dust escaping the face area, and shearing and loading caused the other 40 percent; (2) during sumping, top and bottom sprays were equally effective in dust suppression and reduced dust ~13 percent; (3) during shearing and loading, bottom sprays reduced dust 61 percent and were about 50 percent more effective than top sprays; (4) the combination of top and bottom sprays was slightly more effective than the separate systems, but water consumption increased 60 percent; and (5) inclusion of throat sprays decreased dust reduction by removing some of the water from top and bottom sprays where it was more effective.

Jan 1, 1978

By R. M. Santmyers

Of the sand and miscellaneous silica produced in the United States , ordinary sand and gravel are , of course , the most important, at least as regards volume of output . The building- construction industry absorbs approximately 75 per cent of the total value of all quartz and silica , as shown in Table 2 of Quartz and Silica, Part I, under "General summary . " Because of their unusual physical properties tripoli and diatomite find extremely wide uses in industry, and as the commercial deposits of these ninerals , especially tripoli , are scattered, large quantities enter into interstate commerce . Whereas ordinary sand and gravel are bulky commodities , these specialties have a fairly high unit value and hence can be transported relatively long distances .

Aug 1, 1931

Although the technology involved in removing material from below the earth's surface has a long history, communication systems in underground workings are relatively new to the industry. Communication equipment did not begin appearing in underground mines until the early 1900's. Figure 1-1 shows a miner using a Western Electric standard telephone set for underground mines in 1913. These early phones were essentially the same as those used aboveground, except that they were enclosed in cast-iron boxes as protection against moisture, acid fumes, and gases.

Jan 1, 1984

By Aner W. Erickson

"Magnetite iron deposits on Tolstoi Mountain were examined as part of the investigations by the Bureau of Mines of iron and copper ores on Prince of Wales Island. The Tolstoi Mountain project was a part of a program for investigating mineral deposits in Alaska, under the general supervision of R. S. Sanford, acting branch chief.A preliminary examination was made by S. P. Holt, mining engineer of the Bureau of Mines, in company with John Reed, L. A. Warner, and W. S. Twenhofel of the Federal Geological Survey, on July 14, l943. Three samples were taken, rough estimates were made, and it was proposed that the area be mapped, topographically and geologically,. Dip-needle work was added to the program, and it was decided that, should results warrant, the deposits would be diamond-drilled.From March 26 to May 28, 1944, the deposits were examined thoroughly by Bureau of Mines personnel under the direction of the author. Thirty-two acres were mapped with contour intervals of 10 feet, grids were established covering the principal outcrops, over 1,500 dip-needle readings were secured, and the magnetite bodies were outlined. Additional information was gathered by trench inch and channel-sampling, 600 linear feet of trench being dug and 32 channel samples being cut. Finally, the mapped area was checked for nonoutcropping deposits by taking dip-needle readings at 10-foot intervals along the traverse lines, creeks, trails, and all outstanding topographical features. This re-connaissance work gave sufficient coverage of the 32 acres to eliminate the possibility of further magnetite bodies of any consequence remaining undiscovered.Acknowledgment is made to Nile Johannsen, assayer, Territorial Department of Mines, Ketchfkan, Alaska, for determination of samples.The deposits are on Prince of Wales Island in Southeastern Alaska near Tolstoi Pay, a deep-water indentation at the northwest and of Kasdan Peninsula. The physical features are shown on figures 1 and 2 and the location of the deposition figure 3. Old workings were found on the west side of Tolstoi Mountain; between elevations of 650 and 1,150 feet, at distances of 3/4 to 1-1/4 miles from the east shore of Tolstoi Bay.Access to the area is over a brushed foot trail built by the Bureau of Mines. Topography would permit construction of either surface or aerial tramways at moderate cost but would make road building expensive. Deep-water navigation, permitting inexpensive water transportation, is possible the year around.Kasaan Peninsula is an area of moderate relief, being considerably less rugged than the mainland to the east. Most of the mountains and ridges are less than 2,500 feet in height and show evidence of having been covered by the ice cap of the Pleistocene age. Rock exposures below elevations of 2,000 feet are limited, as extensive overburden 2 to 20 feet deep covers the greater part of the peninsula."

Dec 1, 1948

By Martin J. Gavin

[The theory of fractional "eduction" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil f roan the oil shales of the United States. The term fractional "eduction" gives expression to the rather common belief that when an oil shale is he-test et produces light, low-boiling oils at to temperatures, and increasingly heavier, higher-boiling oils as the temperature of retorting rites. The theory evidently had its is origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases. Thus, gasoline is produced from petroleum at relatively log: temperatures, kerosene at a higher temperature, and heavier products such as gas-oil and lubricating distillates at still higher temepratures, The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and en some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperatures, and so on. Such retorts are usually designed to operate continuously, and. have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts expect that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale basses to zones of increasingly higher temperatures, the vapor lines leading from these zones will remove increasingly heavier products such as kerosene, gas-oil, etc.]

Jan 1, 1924

By F. D. Stevenson

A metal diaphragm pressure relay system was constructed to measure vapor pressures of the metal halides, oxyhalides, and other substances at temperatures up to 700° or 800° C. The vapor pressure of arsenic (III) oxide (As2O3) was determined to verify the reliability of the apparatus for such measurements. The data for the liquid AS2 Os (2820 to 4830 C) are represented by the equation, log Pmm = 6.875 - 2,929/T, from which the normal boiling point was calculated to be 461° C. The heat of vaporization calculated from this equation was 13.40 ±0.09 kcal/g mole As4OS and is essentially constant over the interval studied. The melting point of the octahedral arsenic (III) oxide was determined to be 278° C from the inter-section of the solid and liquid vapor pressure curves, A thermal analysis apparatus is also described by which melting and transition temperatures could be checked by a method independent of vapor pressure data. The melting points of the monoclinic and octahedral forms were determined to be 314.4 ±1.4° C and 278 ±5° C, respectively.

Jan 1, 1963

By P. G. Guest

"INTRODUCTION Need for More information on Spark IgnitionMany questions have yet to be answered more completely concerning the ignition of flammable gases and vapors by electric sparks. Among these one might mention the following: How do the mixture limits for ignition by sparks and by other means compare? Are the most explosive mixtures of the gases the most easily ignited? How ""hot"" must the spark be or what is the minimum energy required for ignition? Does the electric spark act merely as a source of thermal energy or do aggregations of ions, electrons, and metastable atoms formed during and just before the spark play an important part in promoting chemical reactions that ultimately lead to ignition? It is possible for ignition to occur as a result of a silent or brush discharge? How do the ignition energies with single and rapidly recurring sparks differ? What is the relative effectiveness of long, tenuous sparks in ignition as compared with intense, short-gap sparks of equal energy? What is the influence of the material, size, and shape of the spark electrodes? Does the energy for ignition change noticeably with moderate changes in pressure and temperature of an enclosed gas mixture? What order of lag exists between the occurrence of an incendiary spark and the first evidence of flame propagation? What part of a spark in space and time is most effective in producing ignition? Answers to these questions bear directly on the general problem of flame initiation and propagation and, if sufficiently comprehensive, should contribute much to an understanding of the actual mechanism of combustion."

May 1, 1944

By D. E. Stone

Solid and liquid impurities must be removed almost completely from synthesis gas for the production of synthetic liquid fuels because of their effect on the synthesis catalyst and turbocompressors. The maximum permissible concentration of dust has been set at 0.05 grain per 100 cubic feet.5/ This is one part per million by weight, or about the same concentration as in average city air. The cost of synthesis gas is estimated to constitute 60 to 70 percent of the total cost of the synthetic liquid fuel. For this reason this station is developing processes using coal instead of the more valuable coke as raw material, which promises reduction in cost of the synthesis gas. This, however, increases the difficulty of attaining the above dust value. As failure of the dust-removing equipment to produce high-purity gas may ruin valuable equipment within a few minutes, it is imperative that a reliable and continuous method be obtained for determining such extremely low concentrations .of dust in the purified gas. A suitable device must also instantly sound an alarm and, if necessary, automatically actuate the proper valves to prevent damage. The Ess Instrument Co. designed and built an instrument which they believed might fulfill these specifications. It' continually compared, by means of photoelectric cells, the intensity of a light beam passing through the gas and a similar beam passing through clean air. For maximum sensitivity, the photocells were connected back to back, i.e., anode to cathode and cathode to anode. The difference in voltage produced by the two cells was amplified and operated an indicator.

Jan 1, 1951

By J. A. Woolf, E. S. Leaver, N. K. Karchmer

"In the cyanidation of silver ore, the need of oxygen is well recognized. Various methods have been introduced for supplying the oxygen. In usual practice, air is the source of oxygen and the methods of application are mechanical.This article gives the results of touts made to show the rate of dissolution of silver from each of the common silver minerals in cyanide solution, under conditions similar to those used in the practical recovery of silver from its ores. The effect of oxygen in aiding the dissolution of the silver from each mineral is also shown by a comparison of the methods of supplying the oxygen. Oxidation by preliminary roasting (500°C.) of each mineral sample gives the maximum extraction of the silver by treatment with cyanide.Each silver mineral5 used in these experiments was as pure as could be obtained from the mineral dealer. In their natural occurrence, silver minerals are not usually free from mineral impurities. They are usually closely associated with other minerals often forming, a complex mixture. The form of crystallization, the proportions, and properties of the diluent that incases or has been dispersed with the silver mineral may decidedly affect the dissolution rate of the silver from each mineral. While the following results should aid in the cyanidation of silver ores, each ore should be studied from the basis of the form and condition of the silver that is to be recovered.All the tests reported in this article were made on synthetic samples, prepared by mixing the particular silver mineral with clean sea sand. Each mineral was ground in an agate mortar to pass 100-mesh before mixing with the sand which had previously been ground in a porcelain pebble mill to 100-mesh. Such proportions of each mineral and the sand were used as to give a head assay of approximately 20 ounces of silver per ton to the synthetic sample.Agitation was carried on in stoppered bottles approximately one-third full of pulp, method apparently supplied all the atmospheric oxygen that would be taken up by the solution under usual conditions, because tests conducted in open bottles did not show increased recovery,"

Jan 1, 1931

By R. R. Nothdurft

The internal friction of eight single crystals of magnesium with orienta-tion ranging from 10° to 84° was measured at 33.5 kc and 272° C, and the results were interpreted in terms of the pinned-dislocation model proposed by Granato and Lucke. Results show that the strain-amplitude-dependent decrement varies with orientation in a manner predictable by the G-L model. Different values of strain-amplitude-independent decrement were observed at different orientation angles, but correlation with the theory was not conclusive. Problems and steps for further study are discussed.

Jan 1, 1965

By W. W. Graff

This paper describing the mining practices at Mine, No. 4 on the Marquette range, Michigan, is one of a series of articles on mining methods and practices in various mining districts in the United States. Mire No. 4 is located in the Swanzy district, in the southern end of the Marquette range, about 3 miles from Gwinn, Mich. The Swanzy district is an isolated ore-bearing formation, and Mine No. 4 is at the extreme southeastern end.

Jan 1, 1930

By J. J. Burns

Disasters such as occurred at Oppau, Germany, in 1921, at Tessenderloo, Belgium, in 1942, and in this country at Texas City, Tex., in 1947 clearly indicate the explosive hazard associated with the manufacture, storage, and transport at ion of ammonium nit rate The importance and extent of the hazard may be Judged from the large amount of ammonium nitrate produced and transported annually in this country. Between July 1, 1947, and June 30, 1948, it was estimated that the United States produced 461,528 tons of ammonium nitrate commercially for agricultural purposes alone .5/ In addition, U. S. Army Ordnance plants have manufactured and shipped 779,730 tons of ammonium nitrate fertilizer to Germany, Japan, and Korea.6/

Jan 1, 1953

By S. H. Ash

In the early nineties it was observed by several European investigators and by C. S. Rice4 that an explosion could be checked and would not propagate in the parts of a mine where shale or other inert dust was present in large amounts.5 After the disastrous Courrieres explosion in France that killed 1,100 men, coal-dust explosion tests were made in France in 1907 and in Great Britain in 1908 which resulted in the conclusion that if enough incombustible dust were properly spread throughout passageways charged with coal-dust, the propagation of an explosion by the coal-dust could be prevented. In 1908 the Federal government authorized the investigation of the causes of mine explosions and of possible methods of preventing them, with the result that during 1911 the United States Bureau of Mines, after making several tests, suggested that rock-dust be used in gassy or dusty bituminous coal mines. Since that time, experiments and investigations6 have proved conclusively that widespread explosions can be prevented in coal mines by efficient rook-dusting.

Jan 1, 1930

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

"INTRODUCTION The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment, and details of the procedure are given in A.S.T.M. Designation: D271-44 5/. According to the specifications, the following features should be incorporated in the equipment used:1. Oven must have uniform temperature in all parts.2. Oven must be constructed with minimum of air space.3. Oven must have means of changing the air two to four times per minute.4. Air must be dried over sulfuric acid (sp. gr. 1.84).The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general and of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.The semi-automatic moisture tester manufactured by the Brabender Corp. has proved itself in many industrial processes where the rapid estimation of moisture is of vital importance. With the approval of A. C. Fieldner, chairman, A.S.T.M. Committee D-5, and through the courtesy of Lowell Malan, chief chemist, United Electric Coal Companies, who loaned the tester, tests were made to determine the feasibility of using this instrument to determine the moisture in coal."

Jun 1, 1948

By Maria I. DeRosa

This Bureau of Mines report describes the Automated Breathing Metabolic Simulator and its hardware and software systems with emphasis on the role exerted by the software program subroutines in controlling the hardware mechanisms during the simulation of man's respiratory and metabolic functions.

Jan 1, 1978

By Keith D. Rosbury

The basic objective of this project was to determine the cost-effectiveness of dust control used on unpaved mine haul roads. Field testing was conducted at three surface coal mines (two in Wyoming, one in southern Illinois) for a total of 20 weeks. The highest control efficiency measured for a chemical dust suppressant, 82 percent, was for calcium chloride two weeks after application. Generally, however, the control efficiencies hovered in the 40 to 60 per-cent range over the first two weeks since application, and then decreased with time. After the fifth week, the limited number of data points suggest a control efficiency of less than 20 percent. Composite watering data were fairly uniform. Watering once per hour resulted in a TSP control efficiency of approximately 40 percent. Doubling that application rate increased the control effectiveness by about 15 percent to 55 percent. Chemical dust suppressants (primarily salts and lignons) can be shown to be more cost-effective than watering under some conditions. Delta summaries and the analysis of data are contained in Volume I. Volume II contains basic data.

Jan 1, 1983

By Potter G. M.

Ore-dressing tests were conducted on a sample of ore submitted by the Richmond Hill Mining Co. of Lead, S. Dak. as a part of the Bureau of Mines program for investigating potential domestic sources of manganese. Half of the sample was taken from the 300-foot level and half from surface cuts. The problems involved were liberation and rejection of silica and iron and removal of lead, Silver, and gold from the manganese concentrates. Although a portion of the silica and iron oxides was too intimately associated with manganese minerals for rejection by ore-dressing methods, thus limiting recovery of high-grade concentrates, the Richmond Hill ore was found amenable to simple gravity methods of concentration for producing intermediate-grade products. By jigging and tabling, 73.8 percent of the total manganese was recovered in a product that, when sintered, assayed plus 40 percent Mn. Lead, silver, and gold were successfully removed from gravity concentrates by a chloridizing roasting treatment.

Jan 1, 1948

By H. B. Brunot

The United States Bureau of Mines under provisions of Schedule 2C4 issues approvals covering complete operating units such as loading machines, room hoists, and storage-battery locomotives. Certain manufacturers design and build entire machines. Other manufacturers purchase a part or all of the electrical accessories from manufacturers of electrical equipment and make up permissible units by assembling them. Before the assembler purchases electrical accessories for use in such contemplated units he may require certain information from the accessory manufacturer as to whether the particular accessories are suitable for assembly in his proposed permissible outfit. To aid accessory manufacturers in marketing their product, a provision was incorporated in Schedule 20 whereby tests might be made on individual accessories and reports rendered as to the suitability of a given accessory for use in permissible assemblies.

Jan 1, 1935

By Oliver Bowles

The wire saw, introduced by the Bureau of Mines about two years ago, has revolutionized slate quarrying in Pennsylvania. The success of the saw since its early accomplishments has become greater and greater as the equipment has been perfected and skill acquired .in its use. In the first test made, a cutting rate of 9.7 square feet per hour was attained; in the next four cuts, made early in 1927, the average rate of cutting was increased to 12.8 square feet per hour; in 1928 a maximum of 34 square feet per hour had been attained, with a general average of about 20 to 25 square feet, The wire saw is now regarded as essential equipment in practically all of the quarries in the Bangor, Pen Argyl, and Windgap districts. The wire saw consists of a three-strand steel cable of 3/16 or 1/4 inch diameter running as an endless belt. The driving pulley is a 40-inch double-groove cast-iron sheave. A tension pulley supported by a frame mounted on wheels may travel back and forth on a short track. A weight of 800 to 2,000 pounds gives the desired tension on the wire. The driving units consist of electric motors with direct-drive compactly enclosed gear reduction, or double-belt speed-reduction units; the former is preferred. Silent chain and. pinion gear reductions are used to a limited extent. The travelling speed of the wire is about 15 feet per second. The driving and tension equipment are shown in Figure 1, A.

Jan 1, 1929