Search Documents

By Steven A. Fechner

The U.S, Bureau of Mines is conducting a four-year (1987-1990) study to assess the mineral resources and mineral development potential of the Valdez Creek Mining District in southcentral Alaska. This study is part of the Bureau's ongoing statewide mining district evaluation program. This report summarizes the Bureau's site specific evaluations of two areas (Tyone and Peters Creek) of the district that were investigated to determine the bedrock sources of gold and PCM in the alluvial gravel of both areas. In the Tyone Creek area, grains of gold (up to 0.0212 oz/yd3) and platinum group minerals (PCM) were recovered from alluvium and weathered conglomerate of the Jurassic Naknek Formation and Tertiary age using placer sampling techniques, Platinum and palladium were detected in the heavy mineral concentrates recovered from placer sampling the alluvium, and Naknek Formation and Tertiary conglomerates. In the Peters Creek area, grains of gold (up to 0.014 oz/yd3) were recovered from the alluvium and Tertiary Sterling Formation conglomerate. The Bureau's evaluations indicated that drainage basins containing conglomerate are the most favorable targets for placer gold and PGM exploration; and Tertiary conglomerate represents a high volume, low grade gold resource.

Jan 1, 2011

By Donelson A. Robertson

Literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet. No direct evidence of change in water quality or well performance was produced by blast vibrations, but removal of downslope support by excavation does cause lateral stress relief which permits the water-bearing fractures to become more open. This additional storage capacity causes the static water level to drop and for well-bore permeability to improve. Static water level recovers if sufficient recharge is available and well performance is improved.

Jan 1, 1980

By Charles Will Wright

This paper is one of a series dealing with mining problems and summarizing the data contained in the Information Circulars on individual mines that have been prepared by the managers or superintendents and published by the Bureau of Mines. The purpose of this paper is to present the problems encountered in the development of an efficient mine organization and to show the means used by certain mining companies in promoting efficiency. There is also a discussion of the advantages and disadvantages of the various systems of paying and handling labor and a description of their application at the individual mines.

Jan 1, 1932

By R. M. Santmeyers

This paper presents one of a series of digests of foreign mining legislation and curt decisions that is being prepared in advance of a. general report relative to the rights of American citizens to explore for minerals and own and operate mines in various foreign countries. This interpretation of the mining legislation of Madagascar was prepared from the best information (in French) available in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers, to whom it dill be referred through the courtesy of the Department of State. INTRODUCTION The basic mining law of Madagascar is the decree of 1923, signed at Rambouillet by the President of France on July 19, and published in the Journal Official de Madagascar et Dependances. It has been modified by a number of subsequent laves and regulations, generally of minor importance.

Jan 1, 1933

By Eric E. Ungar

Some fundamental facts regarding noise are summarized. Guidelines for reducing plant noise are indicated, and simple means are discussed for determining, whether quieting of specific equipment items will reduce plant noise significantly. Design and installation recommendations are made for quieting chutes by means of dams, impact cushioning pads, impact shields, and damping materials, and for quieting; screens by means of resilient decks, lined screen bottoms, drive mechanism enclosures, and side plate additions. A brief account is appended of the wear and productivity performance of resilient materials observed in three cleaning plants.

Jan 1, 1976

By Robert J. Tuchman

This report presents the origins of the Bureau of Mines and the evolution of the Pittsburgh Research Center from its inception to its present form. Areas of major research emphasis over the years, as well as administrative reorganizations, are discussed.

Jan 1, 1998

By Sidney Katell

This Bureau of Mines study estimates capital investment, operating costs, and selling prices for three underground bituminous mines producing coal with annual production ranging from 1.03 to 3.09 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of November 12, 1973, under the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 indexes. Initial capital investment ranges from $12,938,200 for the 1.03-million-ton-per-year (MJ.Vl tpy) mine to $31,435,500 for the 3.09 MM tpy mine. Total capital investment ranges from $21,607,200 to $51,982,000 for the same mines. Corresponding selling prices for the coal range from $9.11 to $8.06 per ton, assuming a 12-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1974

By A. F. Baker

The Bureau of Mines conducted pressure-drop studies in a 4-foot-diameter simulated blast furnace shaft to compare anthracite metallurgical briquets with coke and formcoke. The test materials were used alone, layered, and in mixed burdens of commercial fuel-to-ore ratios. Anthracite briquets had a higher pressure drop per foot than furnace coke, but they had a lower pressure drop per foot than formcoke. This appears to be due to packing and shape, as well as to particle size. The superficial air velocities at which beds of briquets and furnace coke disrupted were about the same. However, if briquets of the shapes and sizes tested are substituted for furnace coke in commercial metallurgical furnaces, higher blowing pressures will be required to deliver comparable amounts of air. Test burdens with more than 5 percent material smaller than 1/4-inch diameter showed significant increases in resistance to airflow.

Jan 1, 1967

By S. L. Ausmus

The work covered in this report is a continuation of an earlier feasibility study by the Federal Bureau of Mines and points out improvements in the skull-melting method for casting reactive metals such as titanium, zirconium, and hafnium. Machined graphite molds with laminated sections can be reused many times. Large tube sections can be produced by spin casting. Graphite powder is the best expendable mold material, but binders for this use must be compounded carefully. The effects of current and furnace atmosphere on the dependent variables of the casting technique are shown. Because of developments in casting technology for titanium which eliminate the basic problems of melting and pouring the metal, opportunities for improvement in the method have increased. The mold material and gate and riser configurations require particular attention. The limits of application of the casting method have yet to be defined. New knowledge in anyone of these areas could result in marked improvements and simplifications in casting methods.

Jan 1, 1960

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1956 was made under a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 120 samples of aviation gasoline and for 38 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' 1956 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 17 producers of aviation jet fuels are represented.

Jan 1, 1957

By D. R. Brooks

The Bureau of Mines has tested a dewatering technique for phosphatic clay waste. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen or trommel. In field tests conducted in central Florida, clay wastes containing approximately 4 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO-treated material will dewater to 30 pct solids in 80 days. Pretreatment of phosphatic clay waste with lime lowers the PEO dosage required for dewatering.

Jan 1, 1986

By J. R. White, S. W. Lambert, C. M. McCulloch

Examination of several coalbeds in Walker County, Ala., Cambria, Greene, and Fayette Counties, Pa., and Raleigh and Wyoming Counties, W. Va., indicates that cleat orientations are similar throughout a vertical sequence of strata. Studies of cleat orientation were carried out in underground mines that are operating in separate coalbeds vertically above one another. The data show that over a vertical separation of 100 to 400 feet, the average difference in coal cleat orientation between mines is 04° for the face and 08" for the butt cleat. Variations of coal cleat direction between coalbeds examined in strip-mined areas show similar values. Cleat orientations measured at outcrops agree well with the directions measured underground, suggesting that the amount of vertical separation between coalbeds has little effect on the resulting differences in cleat directions. The largest variation of cleat directions between adjacent coalbeds occurs where a large horizontal distance separates two sample locations. Cleat orientations for deeper coalbeds are most reliable where the data are taken from directly above.

Jan 1, 1976

By Verne S. Mutton, William A. Slivensky, Eric S. Weiss, Kenneth L. Cashdollar, Deepak R. Kohli

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, cooperated with Tecrete Industries Pty. Ltd. and BHP Australia Coal in a research program to evaluate the strength characteristics and air leakage of four seal and two stopping designs for use in underground coal mines. A fundamental safety research area for NIOSH is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach to achieve this goal is to develop new and innovative seal designs that provide increased explosion isolation protection for the mining personnel against ignitions that originate from within the gob or. other worked-out areas of the mine Full-scale seals and stoppings were constructed in the Experimental Mine at Lake Lynn Laboratory near Fairchance, Fayette County, PA. They were ail--leakage tested, then subjected to a series of explosions with average pressure pulses ranging from 25 to 500 kPa (3.5 to 72 psi). Instrumentation measured seal displacement and acceleration as a function of time, providing data to assist in the development of numerical models 1'01- future seal design. All three seals designed with Meshblock wire forlnwo~-k ant1 a lnonolithic shotcrete core withstood the first explosion test, which generated an avcr-age rnaximu~n pressure of - 140 kPa (-20 psi) while maintaining acceptable air leakage rates. These seals I-anged from 175 to 325 mm thick. They included a 2.7-m-high by 325-mm-thick seal that was tesled 27 hr after completion against this - 140-kPa explosion pressure, a special requirement of the test program. This seal survived explosions with pressure pulses up to 300 kPa (43 psi). The 2.3-m-high by 325-mm-thick Meshblock seal survived three explosion tests with overpressures up to 455 kPa (66 psi) and satisfied the air leakage criteria. A I ,200-mm-thick plug seal was constructed of two Gunmesh formwork walls in-filled with shotcrete and a 3,450-kPa (500-psi) strength Aquablend core. This plug seal survived three explosions with pressure pulses ranging 11-om 150 lo 430 kPa (-22 to 62.5 psi) with no measurable postexplosion air leakage. Two Gunmesh stoppings with thicknesses 01' 40 and 75 inln withstood explosion overpressures of 23 and 115 kPa, respectively. Anchoring all seal and stopping designs into the roof, ribs, and floor with steel "rootbolts" provided very effective boundary constraint that is critical to the performanceofstructures subject to explosion overpressures.

Jan 8, 1999

By A. D. Hahn

The Federal Bureau of Mines examined ilmenite-bearing sands in southern Texas as part of a program to discover sources of supply for the domestic titanium industry. Deposits were examined from May 1956 through January 1959 in the outcrops of sandstone beds in the Jackson group of Eocene formations in Lee, Burleson, Fayette, and Starr Counties on the Gulf Coastal Plain; in alluvial valley fill in Brewster County in southwest Texas; in the sand beaches of Matagorda Peninsula and the Galveston, Padre, and Brazos Islands--part of the offshore chain of barrier islands along the Texas coast; and in unconsolidated sediments in Willacy County on the Rio Grande delta in the southeast Texas.

Jan 1, 1961

By Ludwig Schmidt

This report, the second of a series, presents the results of laboratory corrosion studies which were made in connection with a one-year test on aluminum lease tanks conducted by the United States Bureau of Mines. Part I of the report contains the results of the field teats.5 The studies were made on an oil lease in a so-called "sour district," near Borger, Tag., where free hydrogen sulphide accompanied the production of oil, gas, and salt water. Steel tanks previously used on the lease had suffered severe corrosion, because steel is inherently susceptible to attack by hydrogen sulphide. Because of the high resistivity of aluminum to the action of hydrogen sulphide, it Was believed that this metal had promising possibilities as a material for the construction of lease tanks in "sour districts." The results of the one-year field teat proved that aluminum lease tanks will withstand corrosion by hydrogen sulphide, but it was found that aluminum was susceptible to attack by salt water, which was invariably present in certain portions of the tanks, and that hydrogen sulphide accelerated this salt-water corrosion in an indirect manner, as will be explained hereinafter. In order to study corrosion conditions encountered in the tanks during the test period, a laboratory was maintained at the site of the aluminum lease tanks.

Jan 1, 1931

By G. T. Fisher

The U.S. Bureau of Mines conducted research on calcium ferrite slags to determine the distribution of Pb and minor elements (Ag, Cd, Zn, and Co) between Pb bullion and slag. These fundamental data are required to evaluate nonferrous smelting with calcium ferrite slags as a substitute for conventional iron silicate slags. Determinations were made in 25-cm3-capacity MgO crucibles at 1,250° C for 2 h in a CO-CO2 atmosphere with an O2 potential that would retard the formation of magnetite. Calcium ferrite slag composition variables studied were from 16 to 32 wt pct CaO in 2-pct increments and Si02 ranging from 1 to 5 wt pct in 1-pct increments with equal additions of MgO. For all compositions studied, the retention of Pb in the calcium ferrite slag was less than 1 wt pct, which compares favorably to about 6 wt pct Pb in conventional iron silicate slags used in smelting of Pb concentrates. Minor element distribution was insensitive to changes in slag composition in the range studied. However, slag composition had significant impact on the melting and fluidity of the slag.

Jan 1, 2010

By D. J. Bauer

The Bureau of Mines demonstrated the feasibility of fractionating lanthanide nitrates with a tertiary amine on lanthanum-cerium and thulium-ytterbium pairs. Optimum values were determined for pH, phase concentration, and percent chelation of metal ions in the aqueous phase. Percent extraction is markedly dependent on the concentration of lithium nitrate in the aqueous phase. Selective masking of the heavier element in each extraction system with DTPA or EDTA aqueous-phase chelating agents resulted in lanthanum-cerium separation factors of 8.5 and thulium-ytterbium separation factors of 3.4.

Jan 1, 1966

By F. X. Tartaron

This report describes work done by the Bureau of Mines to simplify the design and operation of the vortex cone, a new device for prerefining blast furnace iron. Three new apparatus arrangements were tested. Results with one of these arrangements average 74.2 pct silicon removal and 61 pet oxygen efficiency (disregarding removal of carbon and manganese).

Jan 1, 1965

By L. R. Fisher

The purpose of this investigation was twofold: (1) To devise a rapid method for determining quantitatively the porphyrin-carboxylic acid content of a particular crude-oil porphyrin aggregate, and (2) to isolate porphyrins in the crystalline state from crude-oil porphyrin aggregates. The first purpose was accomplished by applying adsorption chromatography. In fulfillment of the second aim three different crystalline porphyries were isolated by methods which involved both adsorption chromatography and fractionation of benzene solutions with hydrochloric acid of varying strength. The three porphyrins had etio, rhodo-, and phyllo-type absorption spectra, respectively. INTRODUCTION Many samples of petroleum have, as interesting minor constituents, chemical compounds known as metalloporphyrins. Their presence in crude oil and other bituminous materials was first discovered by Treibs a quarter century ago. Much experimental work has been done on metalloporphyrins because of their importance to the petroleum industry. They have a deleterious effect on refining catalysts. The ash resulting from the burning of heavy fuel oil is very reactive, We to the presence of metallic constituents, particularly vanadium. In oil-fired gas turbines, the ash may build up on the blades, causing imbalance of the rotors and, in addition, severe corrosion. In industrial boilers, the ash residue is responsible for severe damage to boiler tubes and to the refractory brickwork (15).4 Through study of the chemical constitution of the various metalloporphyrins found in petroleum, much can be learned concerning the origin, migration, and history of crude oils.

Jan 1, 1961

By M. C. McCall

When electric current of any appreciable magnitude flows from a power line into the earth, a change sometimes takes place in the conditions of resistivity immediately surrounding the electrode or medium of contact. If the conducting medium is composed of moist earth or clay the effect is to increase rapidly the resistance. If the conducting medium is coal or a coal bed, the effect is one of slowly decreasing resistance as the coal is carbonized, If, however, the flow of current is not enough to carbonize the coal, it will dry slowly, with a resultant increase in resistance. Measuring ground resistance, or impedance, with conventional commercial ground testers does not always indicate the current that will flow in the earth circuit from a direct-current or an alternating-current power circuit. The exact reason for this has not been determined however, it is thought to be due to the comparatively minute currents used for such testing. A typical ground, tester used by the authors for this work indicated a maximum current of 25 milli-amperes. The frequency of this testing current also has an effect on the readings in all probability. While the possibilities of the effects of varying frequencies has by no means been fully explored in this investigation, there are very definite indications that the impedance of a circuit through a section of earth will vary in some inverse relationship to the frequency of the applied voltages. This is evident at ordinary power-line frequencies ns well as at higher frequencies up to 200 kilocycles, which was the highest frequency available for tests in this investigation. This report is written in the hope that it will stimulate further investigation of the possibilities suggested for communication and the development of safety devices for increased electrical safety in coal mining.

Jan 1, 1952