Search Documents

By John Platt, Mark Stephens

"When blasting is required in critical areas and anticipated shot movement and quick cleanup areessential to the success of the project it is extremely important to use the best technology available to achieve the goals expected by the customer. Wampum Hardware was given such a challenge in 2014-2015 when the PA Turnpike and New Enterprise Stone and Lime hired the company to do presplit blasting along the PA Turnpike. The face height averaged 45 feet (13.72m) and the shots had to be controlled to stop within 60-75 feet (18.29-22.86m) of the face or in this situation before they entered the travel lanes on the PA turnpike. In many if not most blasting environments, it is essential in controlling the movement of a blast, to make certain that the face holes are drilled at exactly the right place, with the proper amount and type of burden in front of and to the sides of the borehole. Profiling is an important first step to insure that the holes are drilled at exactly the right place and showing us the correct amount of burden in front of each and every drill hole."

Jan 1, 2016

By Erica Lorenzo García, Benjamín Cebrian Romo, Antonio Morato Medina

This paper presents the results of a preliminary study on blast-induced vibrations conducted at a Radioactive Waste Storage Facility, located in Spain. The study was undertaken as a preparatory step prior to the blasting operations required for the construction of a new platform located near critical infrastructure housing very-low, low and intermediate-level radioactive waste. The primary goal was to establish a site-specific vibration attenuation curve to safely determine allowable explosive charges based on their distance to sensitive structures. The study followed the criteria defined in the UNE 22.381-93 standard, which regulates permissible vibration levels for different structural typologies. In this case, the existing facilities were classified as Type III structures, given their heightened sensitivity to vibrations. Two experimental campaigns were conducted. Test 1 consisted of a series of 10 individual blasts with increasing charges, monitored by five strategically placed seismographs to record seismic wave propagation and determine the attenuation parameters via regression analysis. Test 2 simulated a production blast using operational charges of 41.7 kg (91.93 lb), applying different delay sequences (42 ms and 25 ms) between holes to assess wave interference, resonance, and constructive effects. Data analysis showed that the longitudinal component dominated vibration transmission, and the predominant frequencies in the most critical zone ranged between 18 and 20 Hz. Based on these values, a conservative peak particle velocity (PPV) limit of 4.75 mm/s (0.19 in/s) was established for blast design. The recorded vibration levels during the tests remained within regulatory limits, with maximum values of 2.35 mm/s (0.09 in/s) and 2.86 mm/s (0.11 in/s) for the sequenced blasts, and peak acceleration of 0.0464g.

Jan 26, 2026

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By Jennifer Williams, Donald J. Berger

Originally built between 1913 and 1916, the Ashton Dam & Hydroelectric Facility has experienced various seepage and piping incidents since completion. Ashton Dam is located within 15 miles (24 km) of the historical Teton Dam failure site and about 2.3 miles (3.7 km) west of Ashton, Idaho. Numerous repairs conducted over the years ranged from filling sinkholes on the crest of the dam to placement of rockfill on the upstream slope to improve seismic stability. In addition, the existing low level outlet works was grouted full and abandoned in 1991 due to significant vibrations induced on the dam during its operation.

Jan 1, 2014

By S. Lim, G. Walsh, V. Romero

The cable television show, Mythbusters, contacted the New Mexico Institute of Mining and Technology requesting a pressure gauge to be used in underwater testing. The requirements for the gauge were: it must be passive (i.e. require no power to function), it must indicate when a certain, pre-determined pressure was reached, and that indication was to be visual. A pressure gauge was developed, using standard, commercially available rupture discs, set to burst at 500 psi. Underwater testing was conducted using a 400 lb Pentolite charge. Test devices were set out at ranges from 50 to 200 feet from the seat of the blast. The rupture discs showed a lethal range up to 100 feet, but not at 150 feet. This result matched well with the behavior predicted through modeling and simple shock physics calculations. Additionally, the geometry between the incoming shock and the pressure gauge did not seem to have a strong effect on gauge performance.

Jan 1, 2009

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

Determining the transitions from run-up to optimal cut length and optimal cut length to run down, without bias, from the penetration of a linear shaped charge (LSC) is difficult. The stresses applied to the targets during explosive testing can distort the targets in such a manner that determining the true distance of cut, penetration, or fracture can be demanding. Through the course of this research, it was observed that the researchers made many of the errors involved in the collection of data. Among these errors researchers found problems in: determining and fitting the sample to a single plane from which to read measurements, determining where along the path of cut the three phases of penetration transition, and the precision of measurement based on handheld tools and the human eye. This study looks at three methods of recording the data of a series of linear shaped charge tests. The tests resulted in samples which are not ideal for measuring with common laboratory devices like measuring tapes, calipers, or rulers. The first method utilized these common laboratory devices and the difficulties the authors experienced are described in this paper. The second and third methods involve digital photography, image manipulation, and the use of AutoCAD. Methods two and three are then compared to the simple observational method and discussion is made in regards to the precision and accuracy of each method.

Jan 1, 2013

By David S. Shatzer, Michael R. Purcell

Current world events have demonstrated the use of commercial vehicles, other unconventional modes of transportation and unusual materials as explosives or incendiary weapons, affecting commerce, disrupting cities and even entire societies. Since the implementation of the Organized Crime Control act of 1970 the Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF) has been investigating and studying explosives and incendiary devices and their related effects.

Jan 1, 2004

By César Ugaz, Jorge Cardenas

Mitigating the vibrations resulting from a blasting rocks is one of the most common challenges that Peruvian mining has, since if this impact is not mitigated it can generate discomfort and altercations with neighboring communities and also puts the continuity of the mining project at risk. In that sense, we must establish control parameters to mitigate these effects as much as possible. As a starting point we must establish areas of interest that in this context would be the communities near the mine; first stage to carry out constant monitoring at these points, the registration of vibrations and noise is vital for the success of this control, with this information we can establish predictive models, the registration of elemental waves and the evaluation of human perception. In a second stage, this information allows us to make decisions in engineering such as the selection of delay times, elaboration of detonation sequence schemes, maximum amount of operating load per delay window, as well as the use of special load designs (Decks). There is a fear that these controls generate negative impacts to the process, referring to fragmentation, dig rate, throughput, etc. Since we limit the explosive load necessary for the results we need. To avoid this we use "Decks" type load designs under a sequencing between these under time calculations by elemental waves, which generate a reduction in vibrations up to 50%, also complying with strict regulations without affecting the power factors to comply with our performance indicators. Finally, in a third stage we must carry out a constant evaluation of results according to the progress of the mine.

Jan 26, 2026

By S B. Richardson, D Mead, N T. Moxon

The use of air-decks to reduce explosive costs has become very topical in recent years. The majority of the research in this area has been arried out between the Soviet Union where reductions in explosive consumption of between 10-30% have been claimed with apparent benefits being gained in both fragmentation and movement. Work carried out by the University of Maryland using thick plexiglass blocks has supported these findings and indicated that air-decks in measetbe duration of action of the shock wave on the surrounding material by a factor of 2 to 5 (see Figure 1). Although the fracture network resulting from this mechanism is not as intense as that produced adjacent to the explosive charge it does appear to act over a larger volume of material. Although the mechanism attributed to air-decking has been studied in some detail the effect of this mechanism on the size distribution of material produced during a blast does not appear tot have attracted much attention.

Jan 1, 1991

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Damien Bretall, William Fourney

Due to the changing face of warfare there is an ever growing need to protect the underside of combat vehicles from mine blasts. This paper presents a new method to better characterize the pressure profiles experienced by a plate as the blast develops. The explosive deformation of a small-scale plate was recorded using synchronized high-speed digital cameras, and then analyzed using 3D Digital Image Correlation software. Time-varying pressure profiles were input into an axisymmetric FEM simulation by fitting curves to data obtained from tests using Kolsky bars to measure pressures. These were then modified to find possible profiles that produce the measured deformations. It was discovered that the final deformation cannot be determined from only total impulse or peak pressures, and that it is very sensitive to the time and spatial decay of the pressures.

Jan 1, 2009

By G. Geremia, M. I. Serrano, L. Costa, Strohaecker

The advances in electronics and the development of more efficient algorithms, allow for the designing of more complex and sophisticated automated systems. The new devices include lighter, faster, reliable, and stronger robot manipulators. One available technology, with relatively low cost, is a simple robot manipulator controlled by remote control. The device has been designed to be used in both mining and law enforcement, where it can be useful for inspection, rescue, gas analysis, and even to manipulate dangerous objects, such as explosives. The applications may even include the rescue of trapped miners in risky environments. The major advantage is the fact that the robot can be controlled with a remote and monitored through a video camera, minimizing human exposure to hazardous areas, where robots can perform tasks in an aggressive atmosphere and confined spaces. This article presents a mining robot manipulator controlled by remote control, using video cameras for positioning and sensors for movements, which are located on the operator's arm. With this system, it is possible to create a sensation of virtual reality, allowing easy operation for anyone trained in dealing with explosives, rescues, or other dangerous tasks. Blasting and mining are becoming perfect applications for robots, and its use should increase very soon. The results are discussed and presented for the brand new Xiru 01 robot manipulator.

Jan 1, 2010

By Corry Goumans, Ron J. Elliot

This paper discusses the challenges encountered in drilling and blasting of a small diameter shaft underneath a parking garage in historic Gastown, Vancouver, BC. This project involved drilling in a restricted headroom area, blasting in a confined space environment, and excavating using a novel vacuum technique. The 1.2m x 1.2 m x 8.5m deep shaft was required for installation of a hydraulic piston for a show lift. The project called for very accurate drilling through inter-bedded sandstone and siltstone within the water table. Development of a unique blast design was required for blast vibration control on a historic structure located just 15.8 meters away. The shaft was successfully completed without damage to any of the surrounding structures.

Jan 1, 2004

By Brandon Fryman, Josh Hoffman, Rhys Baker

A post-detonation debris collection project was led in conjunction with a large ammonium nitrate (AN) railcar detonation conducted by the Department of Homeland Security-Transportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in a Quantitative Risk Assessment (QRA) tool.

Feb 1, 2020

By Corry Goumans

Photos 1 - 4 – Chris Elliott is a rock slope supervisor on a construction project east of Seattle, Washington. His job is to look after a “two man” scaling crew working on the rock bluffs some 300 feet in height along the I-90 interstate just east of the town Hyak. The Washington State Rock Engineers noticed a very large mass of unstable rock along the upper rock face and asked us to take it out. Chris is loading explosives in 1½" ” holes that are 8 to 10 feet deep by 40 feet long with 1¼” x 8” power primer on the unstable rock mass that is about 300 feet above the new road construction. I-90 runs east and west longside the new construction note the containment fence and the ship containers along the highway for protection and Lake Keechelus in the background.

Jan 1, 2014

By Huang Daguang, Paulo Couceiro, Juan Navarro

Mining is typically conducted through a set of interdependent unit-operations, which commonly include drilling, blasting, digging and hauling, in order to deliver the required ore material into the comminution circuit and to remove waste rock with minimum impact in the operation. In such complex environment, the identification of critical paths, and respective interfaces between different unit-operations, are necessary to determine a sustainable long-term operational program. Facing this challenge, adaptive cost optimization strategies are required to increase productivity and revenue while minimizing potential environmental impacts. Since the overall mining efficiency can be strongly impacted by blasting outcomes, an operating method based on the searching of the ideal blast design is required in order to minimize the mine total cost of ownership. The implementation of a consistent continuous improvement program requires specific care in terms of design, control and execution of the different stages of blasting. For that, the application of the most advanced technologies for rock characterization, based on drill monitoring systems, and smart explosive products, allows the improvement and control of blast results by adapting the explosive energy distribution to the rock condition, so as to optimize the performance of downstream stages such as digging, hauling and comminution. This paper describes the application of a heuristic optimization approach, where blast parameters are used as decision variables to evaluate the potential impact of several blasting scenarios on subsequent unit operations, under the continuous ability of modelling, measuring and calibrating operational performances along of the mine cycle.

Feb 6, 2023

By Ali Kahriman, D. Adiguzel, R. Ulger, U. Akkaya

The environmental problems arising from ground vibration has been faced and discussed frequently in various industries such as quarry, mining, civil works, shaft, tunneling, pipe line and dam construction etc. where the blasting operations are unavoidable. This paper presents the results of ground vibration analysis induced by blasting during the construction of the Istanbul Kadiköy-Kartal metro tunnel. Different rock formations in this tunnel route which is 21.6 km in length were encountered during the excavation process by blasting. As a first stage, Hoek’s Geological Strength Index (GSI) values of rock units were determined by using inverse distance weighting method. The GSI values which were obtained from boring data were used when evaluate the data. GSI values were estimated by inverse distance method (figure 3) along with the tunnel route. Afterwards, ground vibration parameters induced by 21 shots which were made in different locations was monitored and passing routes of vibration waves determined. Weighted averages of GSI values were calculated according to distance of the regions where vibration waves passed. Multi regression analyze were made with using frequency, charge per delay, GSI and the distance between the shot point and monitor station. The main goal of this study is to investigate the relationship between ground vibration frequency induced by blasting and GSI.

Jan 1, 2011

By George E. McCormack

At the time of my visit to the Peoples Republic of China I was employed by the E.I. DuPont Company as a Technical Specialist in the Explosives Department. The purpose of my visit was to observe the use of explosives in mining and tunneling in a coal field 500 miles south of Peking near Hsu Chou in Kiang Su Province. The DuPont Company was preparing a proposal for the sale of a Tovex water gel plant to the Chinese Government.

Jan 1, 1982

By Robert Hopler

RBH Note: The Illinois Powder Manufacturing Company was established in 1907 and was acquired in 1957 by American Cyanamid. The latter company left the explosives business in 1969.

Jan 1, 2010

By Diogo Fonseca, José Manuel, Nuno Fernandes, Francisco Monteiro, Andrew Palangio, Blessing Taiwo

This study aims to enhance the integration between blasting and primary crushing operations in quarrying by optimizing the size of oversize and bypass fragments, ultimately reducing energy consumption. Using simulations of multiple blast rounds at the dstgroup aggregate quarry in Portugal, the research seeks to refine blasting practices and improve crushing efficiency. Part 1 of this study, presented at the International Society of Explosives Engineers' 51st Annual Conference, introduced a baseline framework for assessing the compatibility between blasting outcomes and crusher requirements. This methodology was applied to two blasting rounds, revealing discrepancies between expected and actual fragmentation results. The assessment raised key questions, including the root causes of fragmentation mismatches and the identification of controllable parameters that can be adjusted to align the particle size distribution (PSD) with the crusher’s optimal input range. Based on these findings, six key modifications were proposed to improve blast performance: (1) reducing the drill and blast pattern to limit boulder formation in the overlapping regions of hole influence, (2) increasing both the size and length of stemming material to enhance energy confinement, (3) decreasing subdrill depth to prevent toe burden issues from toe deviation, (4) modifying inter-hole timing to relieve back hole burden, and (5) improving drilling accuracy. Part 2, presented at Fragblast 14, explored advanced modifications to the initial blast design. The first adjustment was reducing subdrill and altering stemming material resulted in an 11% reduction in D80, a 19% decrease in maximum fragment size, and a 21% improvement in blast fragmentation efficiency. These changes shifted the PSD by 15% closer to the crusher compatibility envelope established in Part 1. Despite these improvements, boulder generation persisted in the front and back rows of the blast. This third part of the study focuses on implementing the remaining recommended modifications from Part 1 to further enhance blast efficiency and ensure crusher compatibility. The findings contribute valuable insights into the benefits of integrating blasting and crushing optimization strategies to achieve more consistent and efficient fragmentation outcomes.

Jan 26, 2026