Search Documents

By G. E. Christidis, P. W. Scott

The deposits were formed from low-temperature alteration of pyroclastic rocks. Properties investigated include their cation exchange capacity, swelling capacity, pH, rheological properties, the green and dry compressive strengths, shatter index, wet tensile strength, compactability and permeability. It was found that deposits with abundant opal-CT have poor physical properties. The rheological and swelling properties were found to be influenced by the bentonite grade (smectite content) and the degree of disaggregation of the smectite quasi-crystals. The only deposits of high grade which had good foundry properties were those with no opal-CT. Hydrothermal alteration was detrimental to the physical and chemical properties of bentonites in that it decreased the smectite content and the pH and changed the smectite layer charge and the lattice dimensions

Jun 18, 1905

By P. Varona, L. Lorig, M. Board, E. Chacon

Geomechanical factors at the mine are important and will become even more relevant as the pit expands and deepens. To address these demands a team was assembled to collect geomechanical information and perform numerical analysis. The west wall is the largest and flattest of all the design sectors in the pit and rigorous studies were carried out on this wall. The wall behaviour is controlled mainly by a set of steeply dipping joints within the slope in the Fortuna Granodiorite and a weak zone, the Zona Plastica, that extends vertically near the pit bottom. These features lead to large toppling displacements in the upper portions of the wall. Two numerical models were used to reproduce the general features of failure observed in the wall. The modelling indicated that a toppling mode of failure results from shear on the steeply dipping joints. The toppling leads to slumping or landslides whereby the west wall flows slowly downslope as the Zona Plastica compresses

Apr 1, 1996

By J. E. Misiewicz, A Rozendaal

Paper presented at Geofluids '93, held in Torquay, UK, 4-7 May 1993. The tin field consists of a fragment of Lower Proterozoic volcanosedimentary rocks surrounded by granitoids. Almost all the significant deposits are hosted by arkoses and are classified as replacement and space-filling types, with particular styles of mineralisation dominating at different mines. Petrological and geochemical investigation of borehole cores from four centres indicated the presence of a stratified zone 500-600 m thick and continuous over at least 20 km along strike, consisting of pervasively altered clastic arenitic sediments. The alteration is zoned into a grey-green sodic albitised footwall, an 80 m thick sericitised-tourmalinised sulphidic tin zone and a red haematitic potassic hanging-wall. The zoning and the localisation of three cassiterite phases are consistent with the tectonic history and with multiple pulses of stanniferous hydrothermal fluids derived from late differentiates of the granites over a prolonged period. Areas of high fracture density acted as conduits for the fluids, whose initially rapid ascent was retarded by decreasing pressure contrast, limited development of fracturing and/or impermeable shaly arkose to cause lateral spreading and pervasive alteration over a broad, stratified front. Lateral overlapping of local fronts at the various centres suggests a continuous zone, while the many petrological and geochemical similarities point to a shared fluid composition

Aug 1, 1995

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

By K. D. Russ, A. J. Beer

Non-contact systems for measuring underground voids have used theodolites, reflective or non-reflective laser methods and sonar techniques. An effective but cheaper alternative is based on use of a Wild T1000 electronic theodolite coupled to a Leica Data DISTO and a Wild GRE3 data logger. The software used to process the theodolite data is a spreadsheet and macro combination, while Surpac, Datamine and AutoCAD modelling packages have been investigated for viewing the tunnel profiles. The main limitations were found to be blinding, when irregularities in the stope obstructed the line of sight, and the 30 m range of the Data DISTO model used in the study, although more powerful models are available. All three modelling packages proved suitable, with Surpac providing the best-quality printed images of the voids surveyed and AutoCad by far the cheapest alternative

Jun 21, 1905

By P. H. Morris

Nineteen field trials of the co-disposal of fine coal tailings and coarse coal wastes were conducted at the dual Goonyella-Riverside mine in Queensland and at the Hunter Valley No. 1 and Warkworth mines in New South Wales, Australia. The profiles of and the sorting that occurred on the co-disposal deltas are described and an existing theory of subaerial deposition, originally developed for mine tailings alone, is shown to apply to the co-disposed wastes. This enables the dimensionless profiles of large deltas, which may take years to deposit, to be predicted from data obtained from a small delta formed in a few days or even hours

Jun 19, 1905

By C. A. Pickles, J. M. Toguri

The refining of two molten Ag-Cu alloys, containing 7.5 and 11.2 mass% Cu, with a borosilicate slag was investigated using both air and pure O2 to determine the effects of the following variables: flow rate of oxidising gas; injection time; mass of sodium borosilicate flux; and injection of the oxidising gas into either the slag or the metal. The results demonstrate that more than 90% of the Cu can be removed with Ag losses of less than 5% and that refined metal with a Cu content of less than 0.5 mass% can be produced. Ag losses to the slag increased with the amount of Cu removed, and a mechanism is proposed to account for this

Dec 1, 1995

By P. P. Jenkins, T. G. Ball

Paper presented at the Drillex '90 conference held in London, 5 April 1990. Two drilling techniques are employed - guided longhole drilling and reverse circulation coring - for underground longhole exploration of the coal reserves and the fault structures that affect them. These are complementary to, or replacements for, surface boreholes, underground development drivages and seismic techniques. The developments of the drilling techniques and some case histories are presented in detail.

Jan 1, 1991

By L. E. Mordberg, E. N. Nesterova

Geochemical studies of the bauxite deposits show that the primary composition is gibbsitic. Some trace elements were relatively mobile during bauxite formation with the content of Th, U and Zr increasing and that of Rb, Ni and Co decreasing. Y and Pb were relatively immobile during lateritisation; their contents and ratios were inherited from different types of underlying rocks. The supply of Ni and Co took place at the diagenetic or epigenetic stages; their ultimate source was the crystalline basement in the region. The studies support the view that the bauxite was likely to have originated as a result of in-situ lateritisation and not through sedimentary transport and redeposition

Jun 18, 1905

During the construction of storage caverns, and during their lifetime if the use to which they are put so requires, it is necessary to provide adequate ventilation to ensure the safety and comfort of the underground workforce. An analysis of likely contaminants during construction has indicated that where a large facility is situated in a rock mass of even moderate temperature climatic conditions are likely to be the limiting factor during most of the mining operation and atmospheric pollution when blasting is undertaken. Possible options for improvement are increased air flow, cooling of intake air and reduction of the heat source by altering the number and type of haulage units employed in the cavern. Local solutions are an alternative approach where heat problems are confined to a few specific locations

Aug 1, 1994

By E. Niehuis, J. Y. Kim, H. G. Cramer, S. L. Chryssoulis, K. G. Stowe, C. Bendel

TOF-SIMS was used to detect, identify from parent molecular ions and determine the relative concentrations of collectors sorbed on the surface of mineral particles in concentrate and tailings samples from three Canadian concentrators. In the Kidd Creek Zn circuit, sphalerite lost to tailings carried on average a quarter of the amount of isobutyl xanthate present on that recovered to Zn concentrate; amyl xanthate, which is not reported as added to the circuit, was also detected on floated sphalerite and pyrite. At Brunswick, sphalerite particles lost to the scavenger tailings had ten times less amyl xanthate and isobutyl xanthate than those recovered to the Zn final concentrate, while both xanthates were detected on sphalerite floated to the Cu-Pb cleaner circuit. At Matagami, significantly more isopropyl xanthate and isopropyl dithiophosphate were detected on sphalerite recovered to the final Zn concentrate than on that lost to the Zn rougher tailings

Dec 1, 1995

By G. D. Schena, M Zanin

A numerical approach is presented for predicting the liberation of phases during comminution, with direct calculation of a liberation spectrum giving the fraction of the particulate system in each narrow size-composition class. The numerical model uses a Poisson flat process for stochastic generation of the non-convex three-dimensional Poisson polyhedral textures and the system of fractures that give rise to convex fragments. With this numerical approach, there is no need to assume random uniform isotopic fracture (lack of selective liberation); only computational geometry primitives are exploited for the derivation. The agreement with relationships obtained previously under the random uniform isotopic fracture hypothesis demonstrates that the approach is capable of deriving full liberation spectra directly. Both volumetric and superficial composition can be calculated

Jun 21, 1905

By L. T. Isaacs, W. H. Traves

A numerical model for analysing the drainage of fill in mine stopes has been described. The model can be used to analyse the process of fill drainage in existing and proposed mine stopes. The validity and potential value of the model have been established by experience with a simpler, 2-dimensional numerical model and by testing the new model against the earlier model. The new model is more useful than the 2-dimensional model because it allows for heterogeneity of fill material within the stope - a factor that has been demonstrated to affect drainage characteristics significantly. The 3-dimensional model is also capable of predicting pore pressures and drainage rates at specific locations in the stope without the need to resort to 2-dimensional generalisations. Such information, integrated with relevant field data as they become available, will provide valuable mine planning information for the scheduling of filling operations and design of fill mixes

May 1, 1991

By F. T. Da Silva

Concentrates of titaniferous minerals containing around 30 wt% Ta2O5 are processed hydrometallurgically by hydrofluoric acid leaching and solvent extraction, followed by the precipitation of hydrated potassium heptafluorotantalate. A fundamental study of the thermodynamics of this precipitation and recrystallisation was undertaken to increase understanding of the conditions most conducive to the production of pure, well-crystallised K2TaF7. Activity-pH diagrams for the Ta-K-F-H2O system explained the dissolution of Ta2O5 in fluoride solutions quite well and also the precipitation-recrystallisation of K2TaF7.H2O. X-ray diffraction and scanning electron microscopy confirmed the thermodynamic observations. It was concluded that the best precipitating agent for K2TaF7 from fluoride solutions is KF but a recrystallisation step in a HF environment produces purer, well-crystallised K2TaF7.H2O, eliminating oxy-salts and other impurities

Jun 21, 1905

By A. M. Tunstall, N. Djordjevic, H. A. Villalobos

The damage zone behind a typical smooth-wall blast in the open pit was assessed by visually examining diamond drill core to identify blast-induced cracking, mapping core rock quality designations to identify changes in fracture frequency and conducting uphole seismic testing to determine changes in rock mass characteristics. The results from the three techniques show reasonable correlation. They suggest that major damage, in the form of fracturing of intact rock, occurs at least 7 m behind the smooth-wall blast and significant damage, in the form of opening and extension of calcite-filled fractures, at least 12 m from the blast. At greater distances the dominant damage mechanism is the loosening of existent joints within the rock mass. In the trachytes at El Soldado these damage mechanisms correspond to peak particle velocities of 2 000, 900 and 500 mm/s respectively

Jun 19, 1905

To maximise recovery by highwall mining, pillars must be designed which are long, slender and of relatively low width-to-height ratios. The strength of pillars with width/height less than 2 depends primarily on the mechanical response of the coal, due to the reduced influence of frictional restraint between roof and floor. A suitable pillar design approach therefore requires a method of estimating coal-seam properties. Experimental studies were carried out to determine ways of reliably predicting the large-scale mechanical properties of coal seams from small-scale test data. The studies led to a method of practical, systematic assessment of coal-seam properties based on measurement of coal rank and seam brightness profiles. The criterion employs the parameters sigma(c), m and s of the generalised Hoek-Brown empirical strength criterion for rock masses. A novel design approach combines the flexibility of modern numerical modelling programs with simple hand calculation for rapid assessment

Jun 21, 1905

By A. E. Tercan, D. Mamurekli

Ordinary kriging on the assumption of a gaussian error distribution and indicator kriging were used to derive the probability that a given calorific value would or would not be exceeded by coal from an area of a deposit. The two techniques led to similar probability maps despite local differences; the lack of an absolute reference makes it impossible to judge which method is better for this particular application

Jun 19, 1905

By R. L. F. Kay, T. A. Fletcher, A. J. Boyce, C. M. Rice

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The synorogenic, mafic Ordovician intrusion comprises orthopyroxene-rich xenoliths and mafic-ultramafic cumulates with low-grade pyrrhotite, chalcopyrite and pentlandite mineralisation. Despite abundant textural, mineralogical and O isotope evidence for significant assimilation of country rocks, S isotopes indicate only a modest uptake and suggest that mineralisation is dominated by magmatic sulphur. The preferred explanantion is that the magma was close to S saturation on emplacement. Uptake of elements such as Si and O led to early crystallisation of orthopyroxene, resorption of olivine and early segregation of a sulphide liquid. Post-magmatic interaction with a high-temperature, surface-derived fluid, whose movement may have been controlled by regional shear zones, reset biotite and whole-rock O isotope values but not those of orthopyroxene. This model identifies the presence of olivine-rich rocks and evidence of extensive assimilation as guides to prospectivity

Jun 19, 1905

By Qing Wang, H. Sevim

Belt network simulators are the most widely used models in the design of belt networks. The simulators developed in the past two decades are reviewed and their limitations are discussed. To overcome these limitations and to provide a design model that can be used efficiently in real-life applications, a comprehensive non-simulation model has been developed. The features of this model are briefly discussed. A real example is used to demonstrate the model's superiority over belt simulators

Sep 1, 1991

By C. McCall, J. T. Knight, J. R. Ridley

Gold mineralisation in the gabbro sills is mainly stratabound to quartz- and Fe-rich, granophyric-textured units and is sited in undeformed, brittle quartz vein sets, which form pipe-like orebodies. Hydrothermal wallrock alteration consists of hornblende-plagioclase-calcite-quartz with minor biotite, garnet and chlorite and with arsenopyrite and pyrrhotite as the dominant sulphides. Geothermobarometric data suggest that gold was deposited at around 520 degrees C at 2.8-3.8 bar. Mineralisation is thought to have occurred during amphibolite-facies metamorphism. Fluid inclusion and isotope data indicate that gold mineralisation was the result of deposition from a low-salinity H2O-CO2-CH4 fluid of either metamorphic or magmatic origin. Although the Three Mile Hill deposit differs from others in the area in its wallrock-alteration assemblages, peak-metamorphic timing of gold deposition and distinct geochemical associations it forms a brittle stratabound ore body which suggests structural and gold-depositional mechanisms in common with those of the other gabbro-hosted gold deposits

Jun 18, 1905