Search Documents

By Avi Nanda, Robert Brandt, Alex Piatkiewicz, David M. Jones

In 2010 the United States Environmental Protection Agency (UESPA) revised the National Ambient Air Quality Standards (NAAQS) by lowering the permissible value to a 1-hour average SO2 concentration of 75 ppb. In 2012, the USEPA designated the Miami area as non-attaining for the new SO2 NAAQS. A number of options were studied to assist in bringing the Miami smelter into attainment with the new standard. The chosen solution included: Installation of a large tertiary hooding system over the converter aisle; Hooding of the anode vessels and treatment of the anode gas in a baghouse; Installation of a large 2,325,212 Nm3/hr caustic scrubber to treat the captured converter fugitives and anode off-gases; Installation of a secondary ESP for the tapping fugitive off-gas treatment system; and the continuous scrubbing of all acid plant tail stack gases. The modifications have reduced smelter SO2 emissions by 85%, achieving a world class SO2 stack emissions rate of 0.45 kg of SO2/tonne Cu. INTRODUCTION The Freeport McMoRan Miami smelter has been previously described in literature (Steinborn, Pasca, Sallee, Binegar, Bhappu). For the sake of brevity a brief description is given here. The Miami smelter is located 129 km east of Phoenix, Arizona near the town of Miami, Arizona. The smelter was established in 1915 and has undergone a number of process upgrades and modernizations over the years. The present smelter consists of an Isasmelt furnace, an electric settling furnace, four Hoboken converters, two anode refining vessels & one casting wheel; and one double contact sulfuric acid plant. Concentrates are railed & trucked to Miami from four Freeport McMoRan mines located in Arizona & New Mexico. The wet concentrates, typically containing 10% H2O with a Cu/S ratio of 0.85, are smelted in an Isasmelt furnace to a matte grade of 58%. The entire output from the Isasmelt is laundered into an Elkem electric furnace (originally installed in 1972 as the primary smelting furnace) for separation into matte and slag. Slag containing 0.85% Cu is skimmed from the electric furnace and discarded. Molten matte, containing 60% Cu, is tapped from the electric furnace and processed in one of four Hoboken converters to produce blister copper. Two anode refining vessels further refine the blister copper before the final product is cast on a single, 30 mold, casting wheel. All of the anodes produced at Miami are shipped to the Freeport McMoRan electrolytic refinery in El Paso Texas for refining into cathode copper. Smelter off-gases from the Isasmelt, electric furnace and Hoboken converters are combined and treated in a double contact acid plant to produce sulfuric acid. Acid produced at Miami is internally consumed at Freeport McMoRan mines in the region.

Jan 1, 2019

"This document establishes standards and guidelines for scientific and technical disclosure by Issuers listed on the TSX Venture Exchange on their mineral properties. It incorporates and expands upon the minimum standards prescribed by Securities Laws and applies to all oral statements and written disclosure made by an Issuer or on behalf of an Issuer involving mineral properties.1. Introduction1.1 General(a) This Appendix establishes standards and guidelines for scientific and technical disclosure by Issuers on mineral properties. These standards and guidelines should be applied prudently and with common sense by those Issuers in conjmction with the applicable requirements of section 1.2.(b) This Appendix incorporates and expands upon the minimum standards prescribed by Securities Laws and applies to all oral statements and -written disclosure made by an Issuer or on behalf of an Issuer involving mineral properties.(c) This Appendix is not intended to be exhaustive or all-encompassing and greater detail may be appropriate and required in certain situations. Issuers are encouraged to contact Exchange technical staff where they are not certain about the requirement for disclosure on mineral properties."

Jan 1, 2003

By Sadough vanini Ali

Hot deformation behavior of functionally graded steel (FGS) was investigated via conducting hot compression tests at different temperatures and strain rates. Functionally graded steels consist of ferrite, austenite, bainite and martensite layers that are made by diffusion of alloy elements during the melting process. The zenerhollomon parameter has been used to describe the flow stress variations as a function of temperatures and strain rates. The parameter values for all the layers via using the boundary conditions was determined based on composite graded behaviors. Furthermore by applying the rule of phase mixtures, the whole strain rate applied on composite would be the sum of layers strain rates considering the layers volume fraction, while the layers have the same stress. Consequently the composite flow stress for each strain rate and temperature was determined.

Oct 1, 2011

By Helmer Kraemer

One of the CIM 2003 conference themes is ?Globalization and the impact on mine operations?. In this context, the first official version of the new ?International Rock Excavation Data Exchange Standard? (IREDES) is being released. This new standard is a highly flexible data interface for exchange of information between production equipment and central computer systems. The standard was defined by global players in the mining industry and will soon be used to enhance local operations of global mining companies. Beside the standard definition now other aspects are coming into focus: The question how to design and how to implement IREDES compliant data exchange in practice. Implementation of IREDES covers the following aspects: !" Implementation on in-field production systems !" Communication and networking !" Implementation on databases and commercial IT systems In-field production systems are characterized by a big variety of different automation systems. Therefor, different IREDES implementation philosophies have to apply to those systems. One philosophy uses an integrated IREDES compliant automation system on every machine. The alternative method uses one shared IREDES compliant ?Proxy server? for a number of machines connected to this server using proprietary interfaces. Communication and networking can be integrated openly and independently from hardware infrastructures. The only precondition is that communication and networking has to be Ethernet - TCP/IP protocol compatible. IREDES Implementation on the commercial IT level means to exchange IREDES data sets with databases, simulation software, office packages and special applications. Interfacing is easy as long as the software or the database system provides an interface to the Extensible Markup Language (XML).

May 1, 2003

By B. D. Frater

Geometallurgy or process mineralogy is an integrated part of the scoping, pre-feasibility and feasibility phases of a project as well as an existing operation. A well planned and executed geometallurgical testwork programme during the early phases, will result in a more accurate decision making process during the selection phase. The better this integration between geological, mining and metallurgical data gathering during the early phases, the more accurate the predictions will be with regards to throughput and recovery during modelling and process and equipment selection in later phases. This will enhance and improve the mine and process scheduling and subsequent NPV. Geometallurgical information gathered during plant operation and testwork can for example be used to statistically model the pit optimisation, plant throughput and optimise the plant for certain feed material (characterised by statistical models).

Jan 1, 2017

By S. Rash Ahmadi

Thin brittle coatings are deposited or developed on component surfaces for different reasons. In many practical applications the coatings are stressed by externally applied loads. Under such conditions, coating failure can occur. In this paper the probability of the extension of surface crack in coated materials due to cylindrical sliding indentation is analyzed. Contact loading problems typically result in multi-axle and strongly inhomogeneous stress fields near the contact surface. This property which strongly affects the stress intensity factors is taken into account in the failure analysis. Edge cracks were selected to model the actually accruing surface flaws. A suitable method is described for calculating the contact stress fields in coating and substrate. The coating is idealized as a brittle-elastic layer of uniform thickness, which is bonded to the surface of a half space. Method of linear elastic fracture mechanics are then used to calculate the load required to cause fracture in the coating.

Oct 1, 2011

By Torsten Zeller

Due to the increasing worldwide demand for raw materials and the resulting rise in commodity prices more expensive processing that is able to utilize complex ores becomes economically viable. This and increasing ecological awareness is why the interest in recycling and urban mining is steadily growing in Germany. In addition to that; landfills do also contain elements, which were not targeted over the period, when they were being accumulated. Examples are rare earths, indium, gallium, cadmium, arsenic, selenium and tellurium. Also copper, zinc and lead, the target components of ancient mining, can be obtained due to more effective processing and smelting technologies. Funding by the German Federal Ministry for Education and Research, entitled "r³ ? Strategic Metals and Minerals ? Innovative Technologies for Resource Efficiency" also indicates the high level of strategic interest. It is against this background that the research project "Exploitation of the Raw Material Potential of Mining and Metallurgical Tips in Respect of Sustainability as Exemplified in the West Harz Mountains (ROBEHA)" has been implemented. A major concern of this project is the possible transfer of results to landfills in other areas. Therefore the development of an expert system based on the innovative processing methods and a method manual for urban mining are the central components of the investigation. This will provide an important contribution to the cost optimization of ensuing urban mining projects. To ensure the success of landfill mining projects it is necessary to record the composition and quality of the deposits accurately. Also the environmental impact caused by landfill mining and changes in the natural and cultural landscape will be considered in a multicriteria evaluation method. Depending on their origin the tips are divided into the categories mining, processing, and smelting. The content of a landfill and thus the economic potential in terms of urban mining is dependent on the type and composition of the deposits (host rock, gangue, and ore mineral), the available processing and smelting technology, and the target components at the time of mining. Zinc, for example, was not been processed until the 19th century, when it gained attention as being material of economic importance. After such knowledge about a landfill is obtained the decision for further investigations can be made. For a total of 158 landfills in the Harz Mountains, both the volume and the approximate contents of copper, zinc, and lead has been estimated for the different types of tips within past research projects. Based on the prices of the London Metal Exchange (LME) and a euro/dollar exchange rate of 0.76 (as of 03/05/2012) and assuming a minimum density of ? ? 1.5 t/m³ a average value of 1.6 billion ? in copper, zinc, and lead can be obtained. Although only these three metals are considered in this first estimate, it demonstrates the potential of landfill mining and the need for further research. KEYWORDS Urban Mining,

Aug 1, 2013

By T. Cutard, E. Cailleux, F. Nazaret, G. Bernhart

This paper deals with the study of the mechanical behavior in the 20°C-900°C temperature range of refractory concretes reinforced with metallic fibers. Fibers are introduced to improve the damage resistance and to minimize the quasi-brittle behavior of refractory concretes. In some cases, a plastic or ductile like behavior can be obtained. Two approaches are considered in these studies. The first one is based on the micromechanical scale. Main objectives are to understand, quantify and predict the thermomechanical behavior of monofiber microcomposites. Such considerations are helpful to optimize the composite formulation for a better behavior. The second one is based on the macromechanical scale. Main objectives are to characterize and to model the macroscopic thermomechanical behavior of randomly reinforced refractory concretes. A particular attention is firstly paid to the relationships between the microstructural changes and the mechanical properties and secondly to the structural size effects.

Jan 1, 2004

By S. A. Sadough vanini

In this paper the influence of temperature on the flow behavior and rheological characteristics of an A356 alloy in the semi-solid state using backward extrusion process are studied experimentally and numerically. Simulation process is done by dynamic explicit in ABAQUS software for each forming condition. A cooling slope treatment was employed in order to obtain a non-dendritic microstructure. Experiments were performed in 5 temperatures and 4 different wall thicknesses. In the low forming speeds, liquid fraction had time to escape from solid phase forward the samples? wall. This condition was the main reason for the segregation phenomenon seen in the base and walls. Viscosities were determined using the force-displacement graphs obtained form back-extrusion tests. As observed experimentally, in a constant temperature, increase of shear rate resulted in decrease of alloy viscosity exponentially. Raising the temperature increases the liquid fraction hence reduces the semi-solid alloy viscosity. The results of experimental and simulation are compared and there is a good adaptation.

Oct 1, 2011

By D. Naden, D. J. King

"The high capital and operating cost of liquid-solid separation circuits in hydrometallurgical plants has led to an increased focus on the use of in-pulp systems for metals recovery in order to eliminate the need for solids washing and to reduce the need for liquid-solid separation.Carbon-in-pulp (CIP) has now been accepted in Canada and around the world as the leading process for recovery of gold and silver, replacing the Merrill-Crowe process and thus removing the need for CCD thickeners or belt and drum filters. The overall design of conventional CIP adsorption circuits was established in the late 1970s and it has remained substantially unchanged until now. Most of the development work since 'hen has been concentrated on improving methods of separating pulp and carbon and on reducing carbon losses during transportation and agitation.Resin-in-pulp (RIP) has been used for many years in uranium mills in the USA. However, most of the plants were built in the 1960°s and RIP was only chosen when liquid-solid separation of leach pulps proved very difficult. The plants are far from ideal as they have high resin losses and high maintenance costs. Consequently, there is room for improvement.Davy McKee has taken a fresh look at the engineering development of in-pulp contactors leading to a fundamental redesign of the adsorption units. The improved in-pulp technology uses a modification of the proven air-swept screen techno1ogy together with a new technique of process operation. The new contactor operates at high pulp throughput rates with high concentrations of carbon or resin in the recovery stages, resulting in a significant reduction in the contactor size over conventional design. As a result of this reduction in the size of the contactor by up to 80%, significant savings can be made in equipment and building costs. In addition, the plant 1s easier to operate than a conventional CIP plant."

Jan 1, 1987

By Adriana Ramirez, Bradford C. Wesstrom, Blanca Olave

The Freeport McMoRan El Paso Copper Refinery optimizes electrolyte quality using a number of systems. The facility controls copper, arsenic, antimony and bismuth using electro-winning cells within the Tank House and Nickel Carbonate Plant Liberator Circuit (NCP). The NCP manages sulfuric acid content utilizing recycled electrolyte in the slimes autoclave as well as operation of the Acid Purification Unit, APU. The El Paso Refinery removes common sulfates using metal hydrolysis with sodium carbonate. Finally, a Mechanical Vapor Recompression, (MVR), at the water recovery plant removes sodium sulfate generated by the NCP. This paper will provide a summary of these operations. INTRODUCTION In the mid 1920’s Nichols Copper Company, in Laurel Hill, New York, recognized the need for a modern copper refining facility in the southwest. Because of the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the ideal location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Water is a precious commodity in the desert southwest, making conservation of this natural resource an important goal for the El Paso Operations. In the 1980’s, work on the treatment of slimes was improved through the use of pressure leaching of the refinery slimes using an autoclave. Due to the high tellurium content in the leached slimes solution, it was crucial to implement a method for its removal before the solution returns to the tank house electrolyte. A copper telluride cementation operation was installed for tellurium recovery and the ability for the recycle of the leachate and wash water to the refinery electrolyte. In October of 1997, ground was broken for the construction of the water recovery plant using an MVR to reuse process water, reducing water consumption by 25%. In 2002, electrolyte purification was further improved with the installation of an Acid Purification Unit, (APU) (Sheedy, Pajunen, & Wesstrom, 2007). The APU recycles 90% of the acids (both sulfuric and arsenic acids) back to the tank house electrolyte. The solution that passes through the APU is treated with soda ash to precipitate metals out of solution as carbonates and generates a sodium sulfate solution. This sodium sulfate solution is easily processed in the new water recovery plant, where the majority of the water recycles back into the plant as pure condensate. In 2012, the power plant at the refinery upgraded its Reverse Osmosis System to provide RO water to the tankhouse. This insured that the refinery would not have to bleed electrolyte for metals contained in well water such as: calcium, magnesium, iron and sodium chloride.

Jan 1, 2019

By I. B. Lambert

The guide has been developed by officials from resources and environment agencies in the Australian Government and the South Australian and Northern Territory Governments. It elaborates on the Australian Government?s policy that new uranium mines are to be approved subject to world best practice environmental and safety standards. The guide outlines the best practice principles and approaches that apply generally to mining in Australia, before giving more detailed consideration to best practice environmental protection and regulation for ISR mining.

Aug 1, 2010

By O. Zach, K. Gamweger

"The Process of gas purging in molten Aluminium has been an industrial practise for many years. The melting of alloying elements and their rapid distribution in the bath is very important. To improve the mixing and homogenisation process, at RHI NON FERROUS METALS ENGENEERING GMBH a lot of CFD calculations were done. The so developed new ""purging program"" was tested at Alumino Catalan S.A., Spain. The results of the testtrials were very satisfactory and corresponds very well with the calculated data."

Jan 1, 2004

By A. Bouajila1

Minerals processing organisations will be more and more under intense competitive pressure. Major changes are being experienced with intense respect to resources, processes, production strategies and markets. As result of international competition, only the most productive and cost-effective operations will survive. That is why operators in the minerals industry have always aimed to obtain better performance from their processes along the mineral extraction cycle starting from exploration up to the smelting step if any. A principal ingredient and perhaps the most important one in the process of evolution toward improved productivity is the achievement and implementation of an error-free production synonym of an ignorance-free operation. This is, at the same time, a guarantee for quality, a minimising factor for waste materials production, handling and disposal, and a maximising factor for labour utilisation. The notion of ?error or ignorance-free? -usually identified as a ?made in Japan? manufacturing mythology, will sound, at first impression, like a pious ideal, to be striven for but impossible to attain. Nevertheless, the introduction of measurement and detection technology in the minerals industry along the last century should benefit from the today?s sensors and control systems that explosively expanded beyond their traditional production base into far-ranging commercial ventures. The fastness and spread of those technologies will play an important role in the survival of innovative plants. Their role in information assimilation, and control of operations to maintain an error-free production environment, will help many plants to stay effective on their competitive course. In this paper the feasibility of the zero process ignorance concept as applied to the comminution circuits will be discussed and the challenge behind this ambitious move toward improved productivity will be outlined. Examples of pre-competitive R&D projects started at COREM in order to fulfil this prerogative will be presented.

May 1, 2001

Operationalizing the Ruggie Framework in a Mining Context Ruggie?s 3 Pillars: The State?s duty to Protect Policies, regulation, adjudication The Corporation?s responsibility to respect Acting with due diligence to avoid infringing Addressing adverse impacts when involved in abuses Access to Remedy ??even the most concerted efforts cannot prevent all abuse.?

May 1, 2013

By J. Shibata, N. Murayama, H. Yamamoto

As one of effective usages of wastes discharged in the non-ferrous metal industry, the syntheses of AlPO4-5 and hydrotalcite were carried out using aluminium dross as a raw material. AlPO4-5 is an aluminium phosphate condensate with properties of zeolitic materials and large pore size. Hydrotalcite is an inorganic anion exchanger and has a layered structure of complex hydroxide. They were synthesized in an autoclave at high temperature and pressure. Various physical properties such as crystal structure, surface texture, and specific surface area were measured. AlPO4-5 can be synthesized from aluminium dross under hydrothermal conditions at 180°C-200°C, and 3h. At the same time, AlPO4-34 and non-porous AlPO4 were also formed as by-products. The crystals of AlPO4-5 have a hexagonal structure. Lt is desirable to heat the reaction product at around 550 °C to remove tri-ethyl amine. The specific surface areas of the reaction product before and after heat treatment at 550°C were 17.9m2/g and 358m2/g, respectively. Hydrotalcite can be obtained by a co-precipitation method from the aluminium dross and waste MgCl2 solution discharged in the aluminium regeneration process. Small amounts of SiO2, Al2O3, and Fe2O3 remain in the reaction product as an impurity component. The interlayer distance of the obtained reaction product is about 0.3 nm. Hydrotalcite changes to Mg-Al oxide during calcination at 500 °C for 3h, and then hydrotalcite is formed again by a rehydration operation. The physical properties of the reaction products obtained from the wastes were very similar to those from fresh reagents.

Jan 1, 2004

By T. ?kre, O. M. Dotterud, S. Haarberg, J. Thonstad, G. M. Haarberg

An electrowinning pilot plant has been constructed at Falconbridge Nikkelverk A/S, Kristiansand, Norway. The equipment consists of a mixing tank where the electrolyte composition and temperature are controlled, an electrowinning tank equipped with five cathodes and six anodes of commercial size and design and a dechlorination facility. Electrowinning experiments were carried out in this pilot plant using acid cobalt chloride solution from the cobalt tankhouse. Key parameters were varied to obtain an improved understanding of the cobalt electrowinning process, focusing on the detrimental deposition of cobalt oxide on dimensionally stable anodes. The extent of anode scaling was found to be dependent on the electrowinning conditions. Low pH, temperature and cobalt concentration resulted in less scale being formed, however at the expense of cobalt current efficiency and cell voltage, adversely affecting electrowinning production capacity and energy consumption. When operating at high acidity, pH in the anolyte was higher than in the catholyte, which is believed to be due to H+ ions taking part in the current transport across the diaphragm, migrating out of the bags surrounding each anode.

Jan 1, 2005

By R. Tipman

"In 25 years, processing of tar sand progressed from two small pilot plants to two major commercial operations owned by Syncrude and Suncor. These plants mine tar sand and extract the bitumen which is then converted into a synthetic crude oil. Considerable research on extraction of bitumen from tar sand has been undertaken by these two companies as well as other major oil producing companies, private individuals, universities and the federal and provincial governments. These studies have produced a number of alternate processing schemes which have yet to be commercialized. The producing companies are focusing their efforts on achieving increased processing efficiency, which includes improved bitumen recovery, reduced unit cost, energy conservation, and equipment reliability. In this review, the Syncrude process and examples of new process developments will be briefly described. IntroductionTwenty-five years ago, tar sand processing was limited to two pilot plants owned by Cities Service Athabasca Ltd., and Great Canadian Oil Sands. Earnest Manning was Premier of Alberta and was inviting proposals for the construction of a commercial tar sands plant. The invitations called for a much larger operation than those which had been undertaken in the past. All of the previous attempts at commercial operations up to 1960's had failed, largely because of a poor technical understanding of the process requirements, lack of suitable equipment, and lack of adequate capital. The previous record was not good. The pending new large scale plant was based on improved but not proven technology and equipment, which were developed from the pilot plant studies. In addition, the surplus of conventional oil in Alberta and low world oil prices were factors reducing the need for such a plant."

Jan 1, 1987

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By D. A. Akinlade, N. L. Richards, D. C. Murray, W. F. Caley

To investigate the effect of adding Ti to a Ni-Cr-Fe powder metallurgy alloy, a thermodynamic software package was used to predict the phase transformations that occurred during thermal processing. Specifically, the effect of adding 3w/o Ti to a 6w/o Al modified ternary Ni-Cr-Fe alloy (the quaternary) was simulated and the phase transformations that might occur in the material on sintering were obtained using the thermodynamic modeling tool. These predictions were subsequently compared with experimental results obtained by X-ray diffraction and metallography. For comparison, selected compacts were prepared containing only the ternary + 3w/o Ti (no Al). Based upon compressibility curves, the optimum pressure for producing the new Ti compacts was 500 MPa vs 600 MPa for the quaternary composition with Ti. In each case, hardness of the base alloy was enhanced by the Ti addition whereas the residual porosity remained relatively constant at about 19%. Finally, although SEM/EDS failed to confirm the presence of Ti in the gamma prime intermetallic, XRD spectra showed a shift in lattice parameter on addition of Ti, suggesting that the intermetallic was of the form Ni3(Al,Ti).

Jan 1, 2010