Search Documents

By M. J. Pool, P. J. Spencer, J. R. Guadagno

THE present work was carried out as part of a general program to study the magnitude and concentration dependence of exothermic heats of solution of various metals in liquid tin. Thermodynamic data for the Te-Sn system are very limited, particularly for dilute alloys. Indeed, apart from the prior heat of solution determinations of Pool,1 the only other published values are those of McAteer and seltz2 who carried out electromotive force measurements on solid alloys of compositions from 75 to 95 at. pct Te at temperatures between 543° and 668° K, of Colin and Dro-wart3 who made mass-spectrometric studies of the vapor in equilibrium with solid SnTe, and of Robinson and Bever4 who determined the heat of formation of SnTe by solution calorimetry. The present work thus provides further thermodynamic information for this system, specifically in a temperature range where the solubility of tellurium is very limited. The liquid metal solution calorimeter used in this investigation has been described previously.' No further discussion of its design or operation will therefore be given here. For each series of measurements a tin bath consisting of approximately 70 g of 99.99 pct pure Sn was carefully weighed out and inserted in the calorimeter which was maintained at the desired temperature to within ± 1/4°c. Tellurium, of 99.999 pct purity, was supplied by Atomergic Chemetals Co., a division of Gallard-Schlesinger Chemical Manufacturing Corp. Approximately 0.0006 to 0.001 g-atom specimens of tellurium were used for each experimental run and these were added to the calorimeter from a temperature of 273" K. Heat of solution values were calculated by analysis of a strip-chart recorder plot of the heat effect accompanying the solution of each sample in the tin bath. The heat capacity of the latter was determined at regular intervals during a series of tellurium drops by using pure tin or tungsten calibration samples, the heat contents of which were obtained from the standard compilation of Hultgren et al5 The composition of the bath was calculated after each drop from a knowledge of the weights of tin and tellurium added. Values of the heat of solution of tellurium at 725" and 775° K are listed in Table I together with the corresponding tellurium contents of the alloys. The data are also plotted as a function of tellurium concentration in Fig. 1, which includes the equivalent data obtained by pool' at 750° K. It can be seen that the heat of solution remains

Jan 1, 1969

G. D. Kneip, Jr., and J. 0. Betterton, Jr. (Union Carbide & Carbon Corp., Oak Ridge, Tenn.)—The authors have contributed to the theory of zone melting by considering the effects of the solidification of the final zone on the distribution curves for the finite length bar. However, they do not consider in sufficient detail the restrictions imposed by the particular metals involved. Eq. 4 has the analytical solution which is equivalent to Pfann's' equation for normal solidification of the final zone. For distribution coefficients less than one, it is apparent from this form of the equation that, as the solidification approaches completion, the concentration attains extremely large values which are inconsistent with the density of physical materials. The necessary restrictions then are that the solute concentration cannot exceed the density of the alloy, or more frequently, the solubility limit in the solid phase. Secondly, the distribution coefficient cannot be constant from 0 to 100 pet solute unless the liquidus and solidus coincide over this whole region. It would thus be more correct to impose limits on the solubility such as would be indicated by a typical eutectic diagram. Furthermore, in this case the assumption that the distribution coefficient remains constant is more likely to be realized. Eq. 4 should then be replaced by the following C,,(x) =k/L-x [ ?11 3 C11 (x)Ddx - ?11 4 Cn(x)dx= k[Cn (L-l)/k] [ L-x/l]x-1 L-l = x = L-l [kCenterlie/Cn (L-l)]1/k-1 The typical shape for the distribution curve in the final zone is indicated schematically in Fig. 12 for the simple eutectic case. The solidification proceeds according to Pfann's' expression until the concentration reaches the maximum solubility in the solid phasc. At this point, the concentration changes abruptly to the eutectic composition and remains at this value for the duration of the solidification. The width of the flat region, and the back reflection of this effect into the concentration curve on subsequent passes, depends upon the ratio of the eutectic concentration to the original concentration, upon the distribution coefficient, and upon the number of passes. Similar effects on the concentration curves in the first zone length would be expected in many systems for which the distribution coefficient is greater than one, and where the maximum solubility is not too much larger than the original concentration. The discussers agree with the authors that the assumption that the liquid is uniform in concentration should be considered with caution. Kneip and Better-ton' have shown, however, that in floating zone refining of zirconium, using induction heating, the distribution of iron agrees with theory which assumes a uniform liquid composition. Hence, in this case, the experimentally realized distribution coefficient agrees with the present phase diagram within the experimental uncertainty. L. Burris, Jr., C. H. Stockman, and I. G. Dillon (authors' reply)—The authors are happy to have received the comments of G. D. Kneip, Jr., and J. 0. Betterton, Jr., which provide additional insight into the zone refining process. It is true that the equations developed are inapplicable if the solute solubility in the solid phase is exceeded. However, this restriction on the use of the equations was clearly stated in the paper. A closer approach to

Jan 1, 1957

The members of the Institute will recall the account given in the March Bulletin of the inauguration exercises of the Engineering Foundation which was inhibited by an initial gift of $200,000 by Mr. Ambrose Swasey, to be administered by the United Engineering Society as trustees. The Engineering Foundation Board is now constituted as follows: GANG DUNN, Chairman, EDWARD D. ADAMS, Vice-Chairman FREDERICK R. HUTTON, Secretary, JOSEPH STRUTHERS, Treasurer, American Society of Civil Engineers. J. WALDO SMITH, CHARLES WARREN HUNT.

Jan 12, 1915

By James N. Gundersen

Geological Engineering can be all-encompassing and it necessarily overlaps many applications of economic and applied geology. Other review articles will cover specific developments in rock mechanics, open-pit and underground mining, geology, geochemistry, geophysics and geohydrology- all of which overlap many fields of economic and applied geology. Nevertheless, there still remains a diversity of new and innovative applications of geology to engineering works through the activities of federal and state agencies, college and university departments, and industrial or consultant firms-particularly with respect to the properties of earth materials and their behavior "as-is" in nature or under the stress of engineering works. Governmental Agencies: Federal John T. McGill (Chief: Engineering Geology Branch; USGS, Denver) relates that recently the Engineering Geology Branch, together with several other branches of the Office of Environmental Geology, has undertaken the production of interpretive maps of unusual character. These maps are commonly called special-purpose or single concept maps. A folio, or series of maps, is prepared for each topographic quadrangle or area selected for study. The individual maps in a given series are printed on standard-size sheets so that they can be bound together if desired.

Jan 3, 1974

J. A. Mathews,* Syracuse, N. Y. (written discussion?).-It is interesting to note how frequently we hear of some process that is going to revolutionize the tool-steel business. I don't know why it is, but every one seems to have it in for us poor tool-steel men. About 15 years ago, a good-sized plant was built in Syracuse for the manufacture of cast tools of malleable iron. The promoter of the scheme claimed to have a secret, process that had been given to him by a tramp to whom he gave a lift along a dusty road. The widows and orphans invested liberally in the securities of the company without consulting the men established in the machine-tool business in Syracuse. About two years later, when the sheriff's sale occurred, the secret, which was carried on the books of the company as an asset valued at $2,000,000, brought $15 at auction. A little later another concern started on the theory of replacing scrap high-speed steel with new high-speed steel tools made therefrom. All the tool-steel companies have made a practice of purchasing high-speed

Jan 5, 1919

D. M. Riordan has been appointed a member of the Institute Com¬mittee of the Engineers' Reserve Corps movement. Our Committee, therefore, now consists of Henry S. Drinker, Chairman, Messrs. Arthur S. Dwight, Warren A. Wilbur and D. M. Riordan.

Jan 1, 1916

America.-Foreman, J. T. Ashland.-Sturdevant, J. C. AItalIa. Henderson, R. M. Bessemer.-Ball, E. M. Maschmeyer, W. L. McKenzie, W. C., Jr. Birmingham.-Abbott, C. E. Aldrich, T. H. Aldrich, T. H., Jr Aufderhaar, H. C. Berg, H. A. Blair, C. S. Bush, M. W. Clark, G. H.

Jan 1, 1923

ALABAMA America.-Foreman, J. T. Ashland.-Sturdevant, J, C. Altalla; Henderson, R. M. Bessemer.-Ball, E. M. Maschmeyer, W. L. McKenzie, W. C., Jr. Birmingham.-Abbott, C, E. Aldrich, T. H. Aldrich, T. H., Jr. Aufderhaar, H. C. Berg, H. A. Blair, C. S. Bush, M. W. Clark. G. H.

Jan 1, 1929

By R. C. Allen

About four years ago the writer proposed a revision of the correlation of the Huronian formations in Michigan, and noted the bearing of the question on the correlations of the Huronian rocks in Wisconsin and Minnesota.1 Dr. C. K. Leith opposed this revision and argued for the retention of the correlations of the United States Geological Survey, published in 1911,2 for which he and Dr. Van Hise were mainly responsible. As late as June, 1917, Harder and Johnson, following Leith, thought it "premature to change radically a correlation based on years of careful field work."3 The work of Wolff on the Mesabi and Cuyuna Ranges, of Hotchkiss on the Gogebic Range (unpublished), and of the writer and assistants on the Michigan ranges, together with data developed by exploratory and mining operations, has introduced so many new facts not recognized in the scheme of the U. S. Geological Survey that the correlations of 1911 must be considered, in some important respects, obsolete. Indeed, new data are accumulating so rapidly that any classification, which for the moment may seem best to explain the facts, is almost immediately modified or refined by further observations. The problem of Huronian correlations is difficult, but interesting and important. With the aid of fossils, stratigraphers of the post-Algonkian formations have been able to show that slight disconformities mag separate strata of vastly different ages, and that within physically conformable strata may be concealed a hiatus of great magnitude. In the non-fossiliferous Huronian group, minor physical breaks in the strata are only beginning to attract attention, and it is too early to discuss what bearing these will have in correlating the formations of one area with those of another, but it is safe to say that the "lost intervals" which are not disclosed by physical relationships will remain forever lost; therefore we may not hope to discover the ultimate truth concerning the

Jan 1, 1920

By David Keys

THE actual procedure in estimating depth of overburden from mag-netic observations made on the surface will vary with the form of the deposit and any theoretical discussion will apply only so far as the form of the deposit conforms to the mathematical premises on which the theory is based. Since the shapes of natural deposits in the field cannot be expressed rigorously in mathematical form, the best that can be done is to assume some simple form and deduce results. Fortunately many small variations in form produce only slight changes in the estimated depth of overburden, therefore the methods have a definite practical value. For the theoretical treatment, magnetic ore deposits may be divided roughly into three classes, depending upon whether the magnetic anom-alies may be considered to arise from (1) a single magnetic pole, (2) a dike or (3) a magnetic doublet. Particular cases, falling under one or other of these classes, have been discussed by different authors.1-4 In general, it may be stated that when the magnetic effects as measured on the surface are due only to one pole of the body, the other pole being so remote that its effect may be neglected, the resultant anomaly F at any point will vary as the inverse square of the distance r of the point from the pole, which may be expressed mathematically by F = k/r2, where k is a constant. When the deposit occurs in the form of a long, thin dike, the resultant anomaly will be of the form F = k'/r and when the deposit is in the shape of a lens, so that both poles have an appreciable effect on the surface, the result will be similar to that caused by a magnetic doublet, and the form will be F = k'/r3. The particular class under which a deposit falls may be deduced from the results of the magnetic survey. The second class is readily found, but there may be difficulty in deciding between the first and third. Isody-namic contours of both the vertical and horizontal anomalies will often be a good guide in making a correct decision.

Jan 1, 1937

By J. E. Cannaday, R. J. Austin, R. K. Saxer

PREVIOUS investigators have determined activation energies and have postulated various controlling mechanisms for creep.'-' Recently Barrett et 01.I5 have suggested, as the result of their work with cadmium, that the apparent activation energies for creep (AHc) above 0.5 T, could be correlated by means of activation energies for self-diffusion (AHSD) and modulus of elasticity functions: AHC = AHSD - (5RT/E) dE/dT. The wide disparity of apparent activation energies previously obtained with nickel compared to those reported for other fcc metals and the desire to test the postulate of Barrett el al. prompted this study. The as-received 17.5-mil nickel wire used during this work assayed 99.87 pct pure, Table I. X-ray analysis indicated that the wire was in a stress-re- lieved state and metallographic examination revealed an equiaxed grain size of approximately 0.01 mm. Specimens degreased in acetone and cut to 1-1/2 in. lengths were tested in a cam-mechanized constant-stress creep machine. A vacuum of at least lo-5 mm Hg was maintained during all tests. Stresses were applied when thermal equilibrium was established. When a measurable (at least 0.5 pct) secondary creep was observed, the temperature was pulsed to a higher temperature. Pulsing time varied from 30 sec at 480°C to 2 min at 1300'C and above. Slopes of creep curves were determined after the initial acceleration in the strain rate had subsided and steady-state creep was achieved. To confirm the results obtained, additional tests were performed incorporating a temperature pulsing method suggested by sherby. In this method the load was removed during temperature pulsing and reapplied after thermal expansion had occurred. No appreciable differences in results were obtained. Tests were performed over a wide range of temperature (470" to 1310°C) and stresses (250 to 17,000 psi). The expression was used to calculate activation energies. In this expression T1 and T2 are the initial and final temperatures, and el and i2 are the creep rates at T, and T2. The variation of the apparent activation energies with the mean test temperature calculated by means of Eq. [I] are shown in Fig. 1. The mean test temperature (Tmean) was calculated from the relationship

Jan 1, 1967

By Fred Bond

THE process of comminution by grinding is properly classified as an art, rather than as a science. Like most other operations concerned in ore dressing, or in the treat-ment of nonmetallic minerals, the mathe-matical relationships of rock breaking are still obscure, and much disputed. If some basic formula exists, comparable for in-stance to E = RI in electricity, it has not yet been placed in common use. The absence of such a comprehensive mathe-matical background undoubtedly is the cause of many inefficient designs and installations, as well as of much poorly oriented experimental work. On the other hand, the mathematical immaturity of the process constitutes an opportunity for a real contribution on the part of those who enjoy mental pioneering. Some of the statements made in any such exploratory work may be little more than opinions, and it is to be expected that some will later be proved untrue; but such an evolutionary development is necessary if we are ever to arrive at the fundamental laws, the discovery of which can change the empirical art into a mathematically exact science. The most significant principle of com-minution that we possess is probably Rittinger's law, which states that the work done in crushing or grinding is proportional to the area of the new surface produced. There is an alternative theory, known as Kick's law, which formerly was preferred to Rittinger's but which now is rather dis-credited. According to Kick, the work done in comminution is proportional to the volume, or weight, of the pieces broken, or to the cube of their diameters, while accord-ing to Rittinger it is proportional to the square of the diameters.

Jan 1, 1940

By T. J. Koppenaal, M. E. Fine

The critical resolved shear stress of aCu-A1 single crystals has been investigated as a function of composition, testing temperature, and strain rate. The strength, and its temperature and strain rate dependency increase markedly with aluminum content. The solid solution strengthening at 4.2°K is much larger than at room temperature. The activation energy for the low temperature dislocation cutting process increases from about 0.17 ev for a 0.5 at. pct A1 alloy to about 0.50 ev for a 14 at. pct A1 alloy. This result is attributed to an increase in the width of extended dislocations due to the known decrease in the stacking fault energy. In addition, the activation volumes at 4.2 and 77°K decrease with aluminum additions. Concerning the solid solution strengthening in the 296° to 373°K range, no definite conclusions are reached, but it is suggested that subgrains and cutting of subgrains are important. In a previous paper,' the authors reported that adding aluminum to copper produces two types of strengthening: a yield point effect and an increase in the lower yield stress. This behavior is illustrated in Fig. 1 by shear stress-shear strain curves of furnace-cooled single crystals of pure copper and Cu-14 at. pct A1. The yield point effect, At, was thoroughly studied previously1 and shown to be associated with short-range order. The present paper reports an investigation of the lower-yield stress in aCu-A1 single crystals as a function of composition, testing temperature, and strain rate. EXPERIMENTAL PROCEDURE Single cryski1 tensile specimens were prepared in the same manner as previously described.l Briefly,

Jan 1, 1962

By A. G. Paithankar, G. B. Misra

Although certain physical mechanical properties of rocks have been claimed to give an estimate of penetration rate in percussive drilling, the authors' work shows that the correlation of penetration rate with individual rock properties is Poor. The authors have developed a good correlation between penetration rate and a set of rock properties but the relation is complex. Energy per unit volume has been used as a measure of penetration rate in percussive drilling by Hustrulid and Fairhurst; however, their test setup is large wing a full size drill bit. The authors determined the minimum energy for unit volume Ev min for any rock at the optimum index angle in a simple laboratory drop tester wing a sharp microbit with a tip angle of ll0°. This Ev min has been found to correlate well with penetration rate obtained in controlled laboratory drilling in different rocks for different stages of bit wear. A comprehensive relation has been developed between penetration rate and Ev min.

Jan 1, 1981

By R. S. Shoemaker, F. W. McQuiston

SOUTH AFRICAN MILLING PRACTICE All modern South African gold plants operate primarily on the principle of exposing the gold particles in the ore by fine grinding and then cyaniding the total pulp. Although there are minor variations and occasional depart- ures from established practices among the fifty gold mines in South Africa, the normal plant operations proceed as follows. After removal of waste rock by hand sorting (15Y0 on average) the ore is crushed in cone crushers to minus 1/2 inch and then ground to approximately 75% minus 200 mesh by milling with either rod, ball or pebble mills as primary units and pebble mills for the secondary grind. Classification in both circuits is almost invariably conducted with 20" cyclones of 30" or larger diameter. Gravity concentration in the milling circuit followed by barrel amalgamation of the concentrates is practiced in 70Y0 of the plants, particularly where the ore grade is high. A slightly better overall recovery is obtained than with direct cyanidation, but additional handling is involved. Johnson cylinder s , plane tables or belt concentrators, all lined with suitable types of molded rubber riffles, are used for this purpose. At all mines, cyanidation is the main process, usually conducted by continuous treatment in Pachuca tanks and pulp separation with rotary drum filters. Cyanide solutions contain about 0.0 1570 NaCN and require a protective alkalinity of 0.02070 CaO. Precipitation of the gold from cyanide solution is exclusively by zinc dust and lead nitrate using the Merrill-Crowe system in conjunction with Stellar pressure filters. The zinc precipitate is smelted, generally after a preliminary concentration by sulfuric acid, in electric furnaces, mostly submerged arc types, with a silica and borax flux, yield- ing a bullion of 8870 gold, 9% silver, and 370 base metals. The gold content of the ore varies between 0.20 and 1.0 oz Troy per short ton and extraction efficiency ranges from 9570 to 9870. In general, 4070 of the gold output is recovered by amalgamation and 6070 by cyanidation; but in some cases, it is entirely by cyanidation. Flotation has not been adopted for gold extraction as it has not proved as efficient as cyanidation. It is, however, often applied to ores containing higher than 1% sulfur for the recovery of pyrite for sulfuric acid production. On the eastern side of the Witwaters rand Basin, "run-of -mine milling” was introduced in 1960 and in three of the four mills in this area both sorting and crushing have been eliminated. The ore received from the shafts is conveyed to storage silos and then fed by Williamson automatic feed controllers to pebble mills ranging from 12 to 14 feet diameter, and 16 to 20 feet long. The pebble mills operate in closed circuit with 42 inch cyclones and the slime produced is thickened and cyanided in the conventional manner. No selective

Jan 1, 1975

By E. W. Davis

On the eastern end of the Mesabi Range, in Northern Minnesota, is a large formation of siliceous rock which contains bands and fine grains of magnetite. The magnetite comprises about 35 per cent. of the rock, the remainder being chiefly quartzite and iron silicates. The rock has a specific gravity of 3.4, a hardness of 7, and is extremely tough. This large deposit was located early in the history of the Minnesota iron-ore industry but has not been utilized because of its low percentage of iron as compared with the other Mesabi ores, and because of the difficulty and expense of any milling treatment that would concentrate the iron. An investigation, begun about 3 years ago, shows that the magnetit,e is finely disseminated throughout the entire formation and that there are bands or lenses of higher- and of lower-grade material, in which the magnetite and silicate are intimately mixed. As a result, the scheme of milling adopted must include a fine-crushing plant. As it is necessary to crush to 200 mesh in order to produce the desired grade of product, the fine crushing is one of the largest items of expense and for this reason has been given detailed study. It is the purpose of this paper to present some of the results of the work on fine crushing, as to both theory and practice. Previous to fine crushing the part of the rock that contains little or no magnetite can be discarded by magnetic concentrators after each reduction in size in the dry-crushing plant. This-makes it possible to fine-crush a minimum of rock and also establishes the feed to the ball-mill as below % in. The fine-crushing problem, then, consists simply in crushing the rock from 1/4 in. to 200 mesh at the minimum expense. Equipment of the Testing Plant In order to determine, among other things, the operating conditions of the ball-mill when working on this rock, a test mill of about 300 T. daily capacity was erected at Duluth, Minn. The fine-crushing plant contains a Hardinge 8-ft. by 22-in. (2.4-m. by 55.8-cm.) conical mill, a 6- by 27-ft. (1.8 by 8.2-m.) Dorr duplex bowl-type classifier, a 41/2-ft. (1.37-m.) standard Akins classifier, and the auxiliary machinery necessary to handle the products. Each machine is driven by an individual motor, each of which is provided with meters for measuring the power required. Over 150 tests have been made in the ball-mill, varying in

Jan 1, 1920

By I. L. Dillamore

I. L. Dillamore (University of Birmingham)—The different textures developed in various fcc metals have long awaited satisfactory explanation and it has now become clear that these differences are related to parallel differences in the deformation characteristics of the metals. Liu is correct, therefore, in seeking to account for the observed textures in terms of the flow mechanisms but I believe, for the reasons outlined below, that the particular interpretation of flow mechanisms proposed by Liu is open to substantial objections. By considering the forty-eight possible designations of the twelve octahedral slip systems found in fcc metals as distinct and separate deformation modes, Liu has fallen into the error of assuming that only positive glide dislocations associated with each system are present. In fact both positive and negative dislocations will be present and the only difference between for instance the systems B4 and B4' (in Liu's notation) is that under a stress of given sign the direction of motion of a dislocation is reversed on changing from B4 to B4'. For both orientations positive and negative dislocations will be present. In considering possible dislocation interactions it is, therefore, inadmissible to differentiate between R4 and R4' as Liu does. Liu considers those dislocation interactions which give the biggest reduction in energy to be the most favorable and neglects, on the grounds that they will form strong barriers to slip, interactions between dislocations with perpendicular Burgers vectors. Setting aside interactions between positive and negative dislocations of the same slip system, which must occur regardless of the combination of slip systems chosen, the biggest reduction in energy occurs for the Lomer-Cottrell interaction and it is Lomer-Cottrell barriers which are thought to provide the stronger dislocation obstacles. On the other hand the intersection of dislocations with perpendicular Burgers vectors is thought to be a low-energy process which contributes only a fairly small temperature-dependent part of the total work hardening. On this basis it seems doubtful whether the reduction in energy through possible dislocation interactions provides a reasonable criterion for choosing the operative slip systems. From the point of view of texture development it is unsatisfactory to ignore the slip rotations leading to an end position and to neglect to consider the stability of the chosen end point. It is also unsatisfactory to treat the two stress axes as interchangeable since, if the stress system is idealized as biaxial, one stress is compressive and the other is tensile. For the same reason the rotations of the two stress axes are not made compatible simply by assuming that the same slip directions are responsible for the rotations of the two stress axes. It is, in short, essential to treat the two stress axes as acting together on the same slip systems. Turning to the question of the difference between the copper-type and the brass-type texture, there now remains little doubt that the difference is attributable to differences in stacking-fault energy (y), as noted by Liu, but it is doubtful whether the temperature dependence of the texture in copper and in silver is due to increasing stacking-fault energy with increasing temperature. The results of Swann and Nutting42 cited by Liu were obtained in Cu-A1 alloys and the apparent increase in stacking-fault energy on raising the temperature may be influenced by short-range ordering. In pure metals such effects are absent and the only data available on the variation of y with temperature are those of Buhler et a1.43 for silver. They report a minimum at 200°C which does not fit the hypothesis put forward by Liu. It is much more likely that thermal activation of cross slip is important in determining which texture develops, as proposed by Dillamore and tors. These workers have proposed an explanation for the differences in observed texture among the fcc metals and the pole figures predicted consist of an orientation spread which is in better agreement with observation than the limited number of discrete orientations suggested by Liu. The theory of Dillamore and Roberts is also able to account for the differences between aluminum and copper which Liu still leaves unexplained. Y. C. Liu (author's veply)—The writer appreciates the interest of Dr. Dillamore, but must discuss some of his comments in order to avoid cross purposes. The phrase, "forty-eight slip systems," which appeared twice in the text—in the caption of Fig. 1 and the first paragraph in the Discussion—might unfortunately have led Dr. Dillamore to disagree

Jan 1, 1965

"Salt Lake City was founded July 24, 1847, by Mormons under the leadership of Brigham Young. It had a population of 118,110, according to the United States census of 1920, and of 151,968, according to a civic survey, January 1, 1925. The Salt Lake metropolitan district is estimated to have 180,079 inhabitants.The city's area is 51.8 square miles. Its altitude is 4,354 feet. It has 514 miles of streets, of which 91 miles are paved. The streets in the main portion of the city are 132 feet wide and the blocks are 660 feet long. It has 144 miles of street railway and 2,200 electric street lights. It has fifteen parks and playgrounds, forty public schools and six private schools. It has eighty-nine church edifices, of which forty-nine are devoted to denominations other than the Mormon Church.It is the capital of the state, the headquarters of the Mormon Church and the headquarters of most of the mining companies and many other business institutions of the state and adjacent territory.The State University, the State School of Mines and the Inter-Mountain Experiment Station of the U. S. Bureau of Mines are in the eastern part of the city. Fort Douglas is east of the University the country clubs are in the southeastern portion of the city. The State Fair Grounds are in the northwestern portion.The city is the center of a trade area about 700 miles in diameter and is in almost the exact center of a circle that embraces the principal western mining areas. It is the home of several widely-known mining supply companies and all the other leading concerns in that line are represented by agency or branch house."

Jan 1, 1925

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combusts on products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting with gasified carbon (CO) produces (14,140 - 3,960) 10,180 B.T.U. which is (10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total combustion. It is not only logical but practical in partial combustion, converting bituminous coal to gas, to generate the gas with reduced nitrogen dilution.

Jan 1, 1936

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combustion products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting-with gasified car-bon (-CO) produces (14,140 - 3,960) 10,180 B.T.U. which is;(10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first, unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion, and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total, combustion. It is not only logical but, practical in partial combustion, converting bituminous coal to gas, to generate the gas, with reduced nitrogen dilution.

Jan 1, 1936