Search Documents

By Reginald Williams

THE amount or value of the precious metals consumed in dentistry is probably amazing to most people. It falls very little short of that which is consumed in jewelry. Inasmuch as the ultimate destination is in the human mouth, dental alloys enjoy some importance because life and health depend upon restorations made with them. Prosthetic dentistry has made wonderful progress in the last few years. The manufacturers who supply the metals also deserve commendation. This industry which deals with metals to go into people's mouths is comparatively new. There is no literature on the subject, and little or no precedent by which to be guided. It was only by close cooperation with the dentist or prosthetic technician that desirable physical properties were produced, as nearly as possible, in the metals which were available and permissible. It is true that there were and still are conflicting opinions among the dentists as to the physical properties they require. Sometimes they request the impossible, such as alloys which are exceedingly stiff and springy, yet will bend or adjust easily. Even in this latter instance, progress has been made by supplying methods of heat-treatment whereby metals may be softened or hardened at will. (Figs. 1 and 2.) The demands made upon manufacturers are extremely varied. They must supply metals of tensile strengths ranging from approximately 30,000 to 100,000 lb. per sq. in. and over. The latter metals must be workable and in many instances capable of extreme deformation. They must not be affected by mouth conditions, nor should they oxidize greatly when molten, at red heat, or during a soldering operation. In addition to physical specifications, color demands must also be met. The firm of which I have the most knowledge manufacturers 11,553 standard stock articles of precious metals, taking into consideration formulas, finenesses, grades, colors, gages, lengths, sizes and weights. If special demands are taken into consideration, the number would be in excess of 25,000. Wrought metals are manufactured in a great many alloys of different sizes and shapes, such as plate, bar, rod, wire, sheet, strip, mesh and foil. There are also other products of importance.

Jan 1, 1928

By A. H. Daane, B. J. Beaudry

The Sc-Y and Sc-Zr systems were studied by thermal and X-ray methods. Both systems are characterized by complete solid solubility in the low temperature hexagonal form and in the high temperature bcc form. In the Sc-Y system, there is a minimum in the solidus at 50 at. pct and 1365°C, while the solidus in the Sc-Zr system follows a nearly straight line relationship between the melting point of scandium and zirconium. There is a minimum in the temperature of transition from hexagonal to bcc in the Sc-Y system at 43 at. pct Y and 1175°C; while the temperature of transition is raised in the Sc-Zr system to a maximum of 1415 °C at 30 at. pct Zr. INTEREST in the metals of the first transition series has usually stemmed from their useful properties; however, there is now a great deal of interest in determining the fundamental nature of these metals. Since scandium is the first of these transition metals, a study of the preparation and Properties1 and the alloying behavior of scandium2 was initiated. In a continuing study of the alloying behavior of scandium, the systems of scandium with zirconium and yttrium have been established. Extensive solid solubility in both the Sc-Zr and Sc-Y systems was expected from application of the classical rules of Hume-Rothery. Also, the modified Darken and Gurry plot as suggested by Gschneid-ner3 showed ideal conditions for solubility in the Sc-Zr system with less favorable conditions in the Sc-Y system. The effect of scandium on the transformation temperature of zirconium and yttrium was of interest, since a recent empirical observation by Uly and Burr4 predicted that the solute scandium would raise the transformation temperature of zirconium and lower the yttrium transformation. In addition to noting the validity of the above predictions, the SC-Y and Sc-Zr systems were established. EXPERIMENTAL METHODS Materials. The metals employed in this investigation were crystal bar zirconium, distilled scandium prepared by the method described by Spedding, et al.1 and yttrium prepared by the method described by Carlson, et a1.5 The major impurities present in these metals are listed in Table I in ppm. Alloy Preparation. All the alloys examined were initially formed by comelting the two metals in a nonconsumable electrode arc-melting furnace under an atmosphere of purified helium or argon. The buttons were inverted at least five times and re-melted each time to ensure homogeneity. During preparation of Sc-Zr alloys, approximately 1 wt pct was lost which was attributed entirely to the loss of scandium by distillation. When preparing Sc-Y alloys, approximately 1.5 wt pct was lost, but it was assumed that the intended composition was maintained, since the relative weight lost when arc melting the component metals was nearly the same. Samples weighing 15 to 20 g were prepared for time-temperature thermal analysis, while only 1- to 2-g samples were prepared for the optical pyrometer and X-ray diffraction studies. Thermal Methods. The solidus and the melting points of the metals were determined by an optical pyrometer method described previously.2 The temperatures at which the transformation from hexagonal to bcc occurs were determined by differential thermal analysis. Several points on the solidus and liquidus in the Sc-Y system were also determined by this method and are in good agreement with those obtained by the optical pyrometer method. The procedure followed in the preparation of samples for thermal analysis and the furnace used have been described elsewhere.2'6 Since a limited quantity of scandium was available, most of the alloys were not melted during thermal analysis, thus avoiding contamination by the crucible. The alloy could then be reused and the composition changed by adding the desired quantity of solute to obtain the next alloy. Heat Treatment and X-Ray Methods. In order to ensure homogeneity, the "as arc-melted" alloys Were wrapped in tantalum foil, sealed in quartz capsules and heated at 1100°C for 15 hr and then cooled at a rate of 8 deg per min. Samples for X-ray diffraction were filed from these heat-treated alloys, sealed in 1/8 in. by 1/2 in. tantalum capsules under

Jan 1, 1963

By R. M. Larsen

The Rocky Mountain region is defined with some variations for different purposes or by different organizations. For oil and gas development, Wyoming, Montana, Colorado, northwestern New Mexico, and Utah are included in the order of their apparent importance. Portions of adjoining states, such as North and South Dakota, Nebraska, Arizona, Nevada, and Idaho, arc attributary to this region, but have little or no oil or gas production. Nebraska and New Mexico are considered separately (see pp. 412 and 415), and most of the discussion in this report will be confined to Colorado, Montana, and Wyoming. Utah has produced about 200,000 bbl. of oil from the San Juan and Virgin fields, which are isolated and shut in at present. The Clay Basin field in northeastern Utah produces natural gas and distillate, and the Farnham field in central Utah produces carbon dioxide gas. Other Utah areas of some interest are listed in Table I. The Cedar Creek (Baker-Glendive) field in southeastern Montana extends into North Dakota, but is listed under Montana. The other states are in the main wildcat areas, and exploration in 1944 was at a minimum. However, geological and geophysical parties are reviewing them for further testing. Oil production in Colorado, Montana and Wyoming was 459,000 bbl. more than in 1943. Increases of 713,000 bbl. in Colarado and 731,000 bbl. in Montana offset a loss of 985,000 bbl. in Wyoming. This was the first decline in Wyoming since 1938. Field production figures and state totals are given in Table I. Total drilling activities in these three states and Utah increased from 687 wells making 1,442,511 ft. of hole in 1943 to 916 wells making 2,245,803 it. in 1944. Wildcat drilling increased from 163 wells making 331,193 ft. of hole in 1943 to 171 wells making 389,144 it. in 1944. These figures include all drilling wells making footage, not starts or completions, and represent an all-time high in drilling. The year 1944 witnessed the greatest concentration of seismograph activity that the region has had. The Rocky Mountain Oil Scouts Association reported that in 1943, the previous peak year, 91 crew months of work were performed; in 1944, the time was 254 crew months. About 67 per cent of the work was in Wyoming, 18 per cent in Montana, and 12 per cent in Colorado. Twenty-three blocks totaling 400,000 acres were reported assembled in Colorado, and 161 blocks totaling 4,000,000 acres in Wyoming. Information about other states was not given. Fourteen unit agreements were approved by the Department of the Interior, as compared with 13 in 1943. The 1944 agreements were all in Wyoming. In five of the unit areas, oil or gas discoveries were made, four were dry, and five were drilling Or pending' Oil companies find it advantageous to unitize blocks containing any proportion of public domain. Units for

Jan 1, 1945

By Reginald Williams

THE amount or value of the precious metals consumed in dentistry is probably amazing to most people. It falls very little short of that which is consumed in jewelry. Inasmuch as the ultimate destination is in the human mouth, dental alloys enjoy some importance because life and health depend upon restorations made with them. Prosthetic dentistry has made wonderful progress in the last few years. The manufacturers who supply the metals also deserve commendation. This industry which deals with metals to go-into people's mouths is comparatively new. There is no literature on the subject, and little or no precedent by which to be guided. It was only by close cooperation with the dentist or prosthetic technician that desirable physical properties were produced, as-nearly as possible, in the metals which were available and permissible. It is true that there were and still are conflicting opinions among the dentists as to the physical properties they require. Sometimes they request the impossible, such as alloys which are exceedingly stiff and springy, yet will bend or adjust easily. Even in this latter instance, progress has been made by supplying methods of heat-treatment whereby metals may be softened or hardened at will. (Figs. 1 and 2.) The demands made upon manufacturers are extremely varied. They must supply metals of tensile strengths ranging from approximately 30,000 to 100,000 lb. per sq. in. and over. The latter metals must be workable and in many instances capable of extreme deformation. They must not be affected by mouth conditions, nor should they oxidize greatly when molten, at red heat, or during a soldering operation. In addition to physical, specifications, color demands must also be met. The firm of which I have the most, knowledge manufacturers 11,553 standard stock articles of precious metals, taking into consideration formulas, finenesses, grades, colors, gages, lengths, sizes and weights. If special demands are taken into consideration, the number would be in excess of 25,000. Wrought metals are manufactured in a great many alloys of different sizes and shapes, such as plate, bar, rod, wire, sheet, strip, mesh and foil. There are also other products of importance.

Jan 1, 1928

By D. B. Masson

THE martensitic transformations occurring in ,B AgCd as a result of cold working at room temp.. a-ture and cooling below room ten1erature have been reported by Masson and Barrett.1 These authors found that simple cooling to 127°K caused body-cen-tered-cubic AgCd containing 53.0 at. pct Ag to transform to an orthorhombic structure, while mechanical deformation at room temperature was found to induce a hexagonal structure. Furthermore, they observed that the temperature at which martensite first appeared on cooling, Ms, and that at which the transformation was complete, MI, as well as the corresponding temperatures for the reversion on heating, As and Af, could be ascertained to ± 1°K, although they report these temperatures only for the alloy containing 53.0 at. pct Ag (51.96 wt pct). In the work reported here the temperature range of the transformation on cooling was studied as a function of composition, and further consideration was given to the relationship between the original bcc structure and the transformation-induced hexagonal and orthorhomic structures. EXPERIMENTAL PROCEDURE All samples studied were in the form of annealed 300-mesh powder and were prepared from the constituent metals in the manner described previously.1 The compositions in weight and atomic pct are listed in Columns 1 and 2 of Table I. Method of determination of transformation temperature was the same as utilized previously1—measurement of the intensity of X-rays diffracted by the transformation product. A diagram of the low-temperature sample mount is shown in Fig. 1. This mount was made to fit a GE model XRD-3 X-ray diffraction unit. The powder sample was varnished to a flat surface on a copper sample holder at A. This sample holder was soldered to a brass rod, B, which was in turn soldered to a second copper rod, C. Rod C could be cooled to 78°K by inserting it into a reservoir of liquid nitrogen, D. A heater coil of nichrome wire was wound at E on the sample holder, and by varying the current through the heater a thermal gradient could be maintained along brass rod B. Sample temperatures from 78°K up could be attained and held as long as needed. The sample holder and nitrogen reservoir were insulated by Styrofoam, F, and the sample itself was protected by two radiation shields, G. The X-ray beam entered and left the sample chamber through windoys in the supporting container at H and I. Sample temperatures were measured by a calibrated copper-constantan thermocouple varnished to the sample holder just out of the beam at A. The low-temperature structure had been found to possess orthorhombic symmetry1 and the expected positions of the diffraction maxima were known. Therefore the sample was aligned in the X-ray beam and the Geiger counter of the spectrometer set to receive the most intense orthorhombic reflection without an adjacent interfering cubic reflection. This

Jan 1, 1961

By J. D. Prater, H. R. Spedden, E. E. Malouf

With the expansion of copper leaching of the various mine wastes at the Kennecott properties, additional copper recovery facilities have been required. A research and development program has been pursued to determine a suitable economic approach to the processing of the additional leach solutions contemplated. lnvestigations on laboratory and pilot plant scales covered electrowinning, solvent extraction, launder and vat type cells, activated launders, precipitation drums, and precipitation cones. This paper contains information on the development and use of a new precipitation-cone-type copper recovery plant, which provides many advantages over older systems. The application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production. Formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing solutions.1 The detailed investigations which have been made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a new precipitation cone-type copper recovery system providing many advantages over older methods. ELECTROWINNING OF COPPER FROM COPPER-BEARING SOLUTIONS The direct electrowinning of copper from relatively dilute solutions of copper-bearing mine water, namely solutions containing 10 to 20 lbs of copper per 1000 gal, has always been an attractive possibility.2,3 By this method, high-purity copper powder can be recovered with a power consumption of 3.5 kwh per Ib of copper. However, once the solution strength de-

Jan 1, 1967

INTRODUCTION Conditions for formation of porphyry copper deposits appear to have been propitious in the Appalachian orogen from the end of Precambrian into Middle Ordovician, and again from Middle Devonian into Mississippian. In the Appalachians we can now record the evolution of a porphyry copper province within a developing orogen, one that reached metamorphic and structural maturity by the end of Devonian. Fig. 15, after Irwin and Coleman (1972), locates that portion of the Appalachian orogen included in this study, and Fig. 16 illustrates general geology of the area. Deposits mentioned in Table 3 and in the text are shown in Fig. 16. Data presented summarize personal observations by the author, published descriptions of specific areas noted in the bibliography, and abstracts from Provincial assessment files. Sources of previously published data are acknowledged. Few comprehensive descriptions of individual porphyry copper deposits in this area exist, so much of the data presented is new to the literature. Porphyry mineralization has, for this chapter, been restricted to porphyry copper de- posits, although porphyry molybdenum de- posits (Clark, 1972) are also shown in Fig. 16 (Hollister, et al., 1974). Copper- molybdenum and tungsten-molybdenum skarns are also omitted to simplify discu sion, though each is known in the area studied. Gaspe Copper is included, however; min- eralization in this deposit is present in the intrusion as well as in the skarn adjacent (Bell and Scott, 1954). Porphyry deposits listed in Table 3 are included because of some important feature, although other deposits have been reported (e.g., Kirkham and Soregaroli, 1975 ) . Clearly, no table now compiled could be complete. The pace of exploration insures that new occurrences will probably be found. Summaries of features exhibited by intrusions shown in Table 3 should remain valid, however, since they appear representative and are based on an adequate number of deposits in the area studied. Paleozoic porphyry copper prospects (shown in Fig. 16) are more common, apparently, in the northeastern part of the orogen, rarely having been found south of Catheart or west of the Logan Line. Occurrences of molybdenum and other associated lithophile elements are, however, known to the south and west as well as further north. Killeen and Newman (1965), King (1970),

Jan 1, 1978

By Paul Beck

IT is well known that the hardness of metallic single crystals, like that of polycrystalline metals, increases during deformation (hardening by cold-work). It is also known that, as a consequence of deformation, the metallic material acquires an evident thermodynamic instability, revealed, for example, by the fact that the increased hardness gradually decreases with time, especially at elevated temperatures (softening by annealing). The temperature at which the stabilizing process begins is different for various metals, and for any metal it depends on the amount of deformation. Such stabilization of deformed metals may proceed in two different ways: through recovery, and through recrystallization. The former process allows the unstable deformed metal body to approach stability gradually and without visible change in the grain structure; the latter process, like an allotropic transformation, yields directly the undeformed stable "phase" in the form of new undeformed crystals, which, starting out of a certain number of nuclei, grow into and' consume' the deformed hard material. The extent of stability attainable through recovery is limited, espe-cially if the deformation of the metal crystal or crystals involves not only the gliding along slip planes, but also the bending of the slip lamellae, or at any rate the bending of comparatively large parts of the crystal lattice. In such cases, for instance in bent single crystals or poly-crystalline metals subjected to any deformation, recovery will not as a rule be able to restore the "straight" undeformed lattice, and stability can be attained only by recrystallization; that is, by the consumption of the bent crystal lattice parts by new, undeformed crystals-a much more drastic process. It is evident that the part of the surplus free energy stored in deformed crystals, which is present in the form of the elastic energy of the bent lamellae, is in these instances not considerably involved

Jan 1, 1937

By A. S. Bower

Any process which has for its object the preservation of iron and steel from rust, and which will make these metals more applicable than they now are to the requirements of mankind, will be sure to meet with attention from members of this association, and from all those who are either engaged in the extraction of the ore, its reduction to metal, or the subsequent application of the metal itself. It is, perhaps, not too much to say that when iron and steel are rendered secure against corrosion and decay, they will be used to an indefinitely greater extent than they now are. The whole realm of science has, therefore, been explored in the attempt to discover some method by which the formed article may be preserved, leaving its strength undiminished by the destructive action of rust. Paints, oils, varnishes, glazes, enamels, galvanizing, electro-depositing and what is called "inoxidizing" are among the many systems now in vogue to effect the preservation of iron and steel from the corrosive action of air and water. The object of this paper is to show what may he done in protecting iron and steel from rust by forming upon their surfaces a film of magnetic oxide by an inexpensive process. It is no new thing to be told that magnetic oxide of iron is unaffected by exposure to the atmosphere or to salt water for any length of time. The black sand of Taranaki, in New Zealand, is a sufficiently good example of this. Dr. Percy has pointed out that the reason why Russian sheet iron is less affected by exposure than ordinary sheet iron is because of a coating of magnetic oxide; but this was not known

Jan 1, 1883

By W. Rostoker

IN the course of the development of the phase equilibrium diagram for the system Zr-Cr,' the structure of an as-cast allov having the composition ZrCr2 was analyzed and established to be isomorphous with MgZn2 (C14, hexagonal lattice, 12 atoms per unit cell). In a recent paper on the same system, Hayes, Roberson, and Davies' report for the ZrCr2 phase an isomorphy with MgCu2 (C15, cubic lattice, 24 atoms per unit cell). It appeared that this conflict might be resolved by assuming a high and low temperature modification for ZrCr2. That this was the case with the phase TiCr2 has recently been demonstrated by Levinger." Specimens of ZrCr2 annealed at 1200°, 1100°, 994", 900°, 834", 800°, and 700°C, respectively, and subsequently quenched were examined by X-ray diffraction analysis. It was successfully demonstrated that a transition from the MgZn, structure at lower temperatures to the MgCu, structure did occur at some temperature between 900" and 994°C. Table I lists the observed structures at the various annealing temperatures. In Table II, a summary of line spacings and intensities is given for each of the allotropic modifications. The first six lines of the MgCu2 structures have been located in the table to illustrate the close similarity between the patterns. Lattice parameters of the two modifications were calculated by a least squares solution of equations for interplanar spacings for a series of high angle lines. The results are as follows: MgZn2 type - c = 8.262 kX, A = 5.079 kX. MgCu2 type — a = 7.195 kX. It is interesting to note that TiCr2 behaves in reverse fashion yn that the MgCu, structure is the low temperature modification and the MgZn2 structure is the high temperature modification. References lR. F. Domagala, D. J. McPherson, and M. Hansen: This issue p. 279. 'E. T. Hayes, A. H. Roberson, M. H. Davies: Trans. AIME (1952) 194, p. 304; Journal of Metals (March 1952). 3B. W. Levinger: Trans. AIME (1953) 197, pp. 195-196; Journal of Metals (February 1953).

Jan 1, 1954

By S. S. Clarke

THE opening of zinc-lead ore bodies in the lower chert beds of the Tri-State district, locally called sheet-ground deposits, [ ] presented several new economic operating problems to be solved before the low-grade deposits could be mined profitably. Drilling was the first high-cost problem and loading and haulage difficulties followed. At this time, the sheet-ground mines are producing about 2000 tons per day. GEOLOGY The geology and ore deposits of the Tri-State district have been covered in detail by [ ] Fowler and Lyden.* Briefly, the sheet-

Jan 1, 1942

G. M. TAYLOR,* Colorado Springs, Colo.-The ore treated at the United Eastern is primarily a gold one and is cyanided-the counter-current decantation method being employed. One of our employees visited this plant a few months ago and, on his return, reported that the moisture in the tailing was carrying 20 c. per ton, which would appear to be somewhat high. As this type of plant has been advocated by one of the recognized cyaniding engineering firms in the country, and a number of these plants are in successful operation, it does not seem to me that the dissolved loss could be so high, and I would like to know if any one can give any definite information on this point? J. V. N. DORR, New York, N. Y.-I am very glad that Mr. Taylor has raised this question. When I first read Mr. North's paper and saw his statement, that they had an actual dissolved loss of 21.5 c. per ton, I was very much puzzled at this high loss which appeared avoidable by another decantation or the addition of a rotary filter. Reading it again, however, I noted that the actual dissolved loss of 21.5 c. given was evi-dently obtained by multiplying the assay of solution discharged from Z. thickener by the tonnage. On the basis of 283 tons milled per clay, this means $56.54 going to the clam. He states, however, that he returns from. the dam into the system, 70 tons daily assaying 40 c. per ton or $28 per day, so it would seem reasonable, unless I have overlooked something to regard the actual dissolved loss as $56.54 less $28 or $28.54, equaling 10.8 c. per ton. Even this loss, however, is much higher than good practice elsewhere, and can be accounted for largely by the tonnage being handled, which I believe is 30 per cent. above the capacity planned.

Jan 12, 1919

By Frederick T. Fischer

INTRODUCTION Post-Lower Ordovician karstification on a continental scale produced a wide-spread paleoaquifer in the upper portion of the Knox Group of the Southeastern United States. The presence of economic zinc deposits in the Knox of Tennessee is considered to be a con- sequence of this paleoaquifer(1). During The New Jersey Zinc Company's initial exploration of the middle Tennessee region the known artesian nature of modern Knox water and its potentially adverse effect upon mining activities was a matter of concern. This concern intensified as a mining situation appeared imminent and a program of hydrologic investigation was begun in early 1969 and continued through August 1972. The preliminary findings of this work were reported at the AIME World Symposium on Mining and Metallurgy of Lead & Zinc in 1970(2). This paper presents additional data acquired during subsequent stages of the program and relates the hydrologic relationships to the overall geologic framework of the area. PHYSICAL GEOGRAPHY The Elmwood mine is 85km east of Nashville and 8km southeast of Carthage in Smith County, Tennessee (Figure 1). Its physiographic location is in the Central Basin of Tennessee, a basin resulting from erosional breaching across the Nashville Dome of the Mississippian strata which now form the bordering Highland Rims. Both the Central Basin and Highland Rims are divisions of the Interior Low- lands Province. Outcropping rock units of the Central Basin are predominantly Middle Ordovician limestones with scattered high hilltops capped by Devonian and Mississippian strata. One outlier

Jan 1, 1977

By Emanuel Trotz

As the long-felt need of a reliable and easily-managed pyrometer has now been fully supplied, by the latest form of Professor Wiborgh's pyrometer, an account of this instrument will, per-

Jan 1, 1893

By D. Turnbull, J. H. Hollomon, J. C. Fisher

Application of the concepts of nu-cleation and growth to the analysis of experimental transformation data has led to valuable descriptions of phase transformations, an outstanding example being the transformation austenite —* pearlite which has been examined with particular care by Mehl and co-workers.&apos;-5 In addition to the pearlite transformation, the proeutectoid fer-rite and proeutectoid carbide transformations are known to proceed by nucleation and growth. Martensite, on the contrary, until recently was thought to form by a mechanism involving neither nucleation nor growth; however, extension of standard nucleation theory6 suggests that martensite, bain-ite, and the other products of austenite decomposition all grow from nuclei in the parent phase. The theory that martensite forms by nucleation and growth is strongly supported by recent experimental work of Kurdjumov and Maksimova.7 The concepts of nucleatioli and growth have been fruitful also in providing a sound basis for quantitative theoretical treatments of the kinetics of phase transformations. For example, Volmer and Weber8 and Becker and Döring9 developed the theory of nucleation from fundamental considerations to a point where excellent agreement was obtained with the results of experiments on the condensation of supercooled vapors. As a result of their analysis, the kinetics of vapor-liquid transformations now can be predicted. It seems probable that application of the theories of nucleation and growth to a quantitative study of austenite decomposition similarly will clarify the nature of the individual transfor: mations involved, and will enable the calculation of austenite transformation kinetics. In the present paper, the theories of nucleation and growth are applied to the austenite ? martensite transformation in steels. The analysis begins with a discussion of nucleation in single component systems. Martensite appears to be coherent with the parent austenite, hence the nucleation theory is modified to include the effects of elastic distortion. Nucleation in the two component iron-carbon system then is discussed, for most steels are primarily alloys of these two elements. Finally, M. temperatures and martensite transformation curves are calculated for each of several alloy steels of varying carbon and chromium content, and are compared with those determined experimentally by Lyman and Troiano10 and Harris and Cohen.11 Nucleation Theory NUCLEATION IN SINGLE COMPONENT SYSTEMS6,12-14 The work required for reversible formation of a region of phase within the parent a phase is expressed conveniently as the sum of two terms: W1 = Aa, the product of the area of the interface and the interfacial free energy, and W2 = VAf, the product of the volume of the region and the free energy increase per unit volume associated with the transformation. The total work is therefore W = Aa + VAf. When a is more stable than ß, Af is positive and W increases without limit as the volume increases. The transformation a ?ß does not occur. It is nevertheless true that small regions of phase ß enjoy temporary existence here and there in the a. The equilibrium number of ß regions of given size is proportional to exp(— W/kT) per unit volume of a, assuring that larger (ß regions occur with diminishing probability. When a is less stable than ß, Af is negative and W passes through a maximum as V increases. Assuming for simplicity that regions of ß are spherical, as is true when the interfacial tension is isotropic and there are no elastic strains, W = 4r2a + (4/3)*r3Af The maximum value of W is W* = 16iro3/3Af2 [1] for regions with radius r* = -2o/Af. [2] For single component condensed systems it has been shown14 that the steady rate of nucleation of 0 per unit volume of untransformed a is nearly proportional to exp[- (W* + Q)/kT] where Q is the activation energy for the unit processes of adding or removing one atom from an embryo or nucleus. If To is the temperature at which a and ß are in equilibrium, the rate of nucleation is a maximum at a temperature 0 < T < To where (W* + Q)/kT is a minimum. P regions smaller than critical size are called embryos; they tend to grow smaller and disappear, only exceptionally growing larger. Regions equal to or larger than critical size are called nuclei. A critical size nucleus may grow indefinitely large or may shrink back to a, either process decreasing the free energy of the region.

Jan 1, 1950

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period August 1, 1916 to September 10, 1916: C. L. Cantley, New Glasgow, N. S. H. M. La Follette, La Follette, Tenn. D. A. Cowell, Columbus, Ohio. Montrose L. Lee, Montevideo, Uruguay. Alexander Deussen, Houston, Texas. V. H. McNutt, Billings, Mont. Chas. E. Dutton, Goldfield, Nev. J. W. Maller, New York, N. Y. H. S. Emlaw, Grand Haven, Mich. Edwin W. Mills, Tul. Mi Chung, Chosen, J. M. Gillette, Swatsburg, N. Y. Korea. E. Gorilla, San Antonio, Texas. Francis R. Pine, Elizabeth N. J. Bertram Grant, Kingman, Arizona. Frank A. Ray, Columbus, Ohio. Ruger W. Hay, Bisbee, Arizona. John A. Rice, El Paso, Texas. C. F. Hendricks, Cobalt, Ontario. W. E. Rice, Ringwood Manor, N. J. Stanley C. Herold, San Jose, Cal. W. H. Staver, Lynchburg, Va. Lloyd Hoffman, Pottersville, N. J. Ralph H. Sweetser, Easton, Pa. Charles Hunter, London, England. Kirby Thomas, New York, N. Y. G. Jansen, Benkoelen, Sumatra. Henry Traphagen, Union Hill. T. H. Jenks, Oatman, Arizona. M. M. Valerius, Tulsa, Okla. Warren jenny, Chanaral, Chile. Wilfrid B. Wainewright, London, Eng. Walter A. Barrows, Jr., of Brainerd, Minn., has been elected president and general manager of the Thomas Iron Co., Easton, Pa., to succeed Ralph H. Sweetser, whose resignation of several months ago becomes

Jan 10, 1916

By Layson, W. C.

ACCORDING to the records, Phelps Dodge made its original entry into the production of copper in the oldest copper mines of Arizona at Morenci in 1881. The ore body now being mined as the Morenci open-pit, as outlined by churn-drill holes, diamond-drill holes, and underground workings, is estimated to yield 230,000,000 tons of ore averaging 1.06 per cent copper. This development will add 2,500,000 tons of copper to the 900,000 tons already produced in the district. Some five years ago preliminary development of the ore body began, with big-scale production planned including the erection of a new treatment plant to be built near the mine. Inasmuch as the Morenci open-pit was an entirely new project this required the grading of roads, establishment of mining benches, construction of railroad grades, building of railroad tracks, erection of shops, as well as the purchase of the necessary equipment to satisfactorily and economically maintain the schedules of production forecast. Along with the preparation of the main ore body it was also desirable to mine and deliver to an experimental mill a relatively small daily tonnage of typical ore.

Jan 1, 1942

By G. H. Clevenger

Continuing the discussion of the paper of James Johnston, presented at the New York meeting, February, 1914. See Trans., xlviii, 3 to 32 (1914). This paper cannot fail of being of great interest and value to all who are interested in the cyanide process, on account of the important developzn~ents which it records. Mr. Johnston is to be commended for the large amount of detail which he gives, and the company and its management for permitting the publication of data of this character, which while of great value to others could well be considered private property. It might be discussed from a number of standpoints: First, as an example of recent practice in mill and cyanide plant construction; second, the mill practice; third, the cyanide practice; and fourth, the new features in cyanide treatment involved. Perhaps a more vivid way of expressing it would be: First, the equipment or tools with which the various operations are carried on, are they the best and most efficient which could have been selected for their respective uses; and, second, is the best use in every case made of these tools? It may be well inquired is the highest possible recovery of silver made at the lowest cost per ounce recovered? For after all, the making of the greatest ultimate profit is inseparably associated with successful metallurgical practice; there must therefore be at all limes a careful balance maintained between recovery and cost of obtaining it. I wish to call attention in a very general way to the equipment used and to an anticipation of questions which are bound to arise in this connection. However, the bulk of my discussion will be confined to the presentation Of certain additional data, together with a more or less general discussion showing the line of development which leads up to the present practice and the applicability of certain features of it to similar problems elsewhere. There are a number of vital points of broad general interest involved in Nipissing low-grade practice upon which metallurgists will by no means be agreed to which I wish to call particular attention in the hope that it will lead to the presentation by others of data of practice in other districts which will assist in reconciling this divergence of opinion.

Jan 1, 1915

Aamot, Olav Crone, (M&apos;29) Chem. Engr., Elektro¬kemisk, Raadhusgt, 23; Oslo, Norway. Abadilla. Quirico A., (M&apos;33) Min. Engr., Dir., Bureau of Mines, Manila, P. I. Abbott, Agatin T., ( J&apos;40) Asst. Geol., Trench Mine, Patagonia, Ariz. Abbott, Clarence E., (M&apos;04) Civil Engr., V.P., Tennessee Coal Iron & R. R. Co.. 159&apos;3 Brown Marx Bldg.. Birmingham, Ala. Abel, Raymond L., (M&apos;28) Chem. Engr., Chief of Inspection Div., Pittsburgh Chem. Warfare Pro¬curement Dist., American Batik Bldg., Pitts¬burgh. Pa. Abel, Walter D., (M&apos;32) Min. Engr.. Div. of Cor¬porations, State of Calif.. 403 California State Bldg., Los Angeles, Calif. Abele. Louis T., (M&apos;31) 4800 Patterson Ave.. Richmond, Va. Abell, Leo M., (M&apos;311 Research Met., Mount Mor¬gan Ltd., Mount Morgan, Queensland, Australia. Abenius, Hakan V., (M&apos;37) c/o Falu Gruva, Falun, Sweden. Abernathy. G. E., (M &apos;33S) Geol., Kansas State Geol. Survey. Pittsburg, Kan. Abernathy, Jack. H.. (M&apos;40) Chief Engr., Sunray Oil Co.. Philtower B1dg., Tulsa. Okla. Ahorn, Robert H., (M&apos;19) Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. Abraham, A. W., (M&apos;30) Petr. Engr., Richfield Oil Corp., 555 S. Flower St., Los Angeles. Calif. Abramowitz, William L., (J&apos;40) Chem., National Oil Products Co., Harrison, N. J. Abrams, Charles Jackson, (M&apos;36) Gen&apos;l Supt., Climax Molybdenum Co.; Climax, Colo. Abstein, Henry T., (M&apos;27) Yellow Pine, Idaho. Ackerman, D. E., (M&apos;35) McKinsey & Co., 2 Wall St., New York, N. Y. Ackerman. E. Dumont, (A&apos;3S) Petr. Geol.. Dist. Geol., Quiriquire&apos; Dist., Standard Oil Co. of Venezuela, Caripito, Venezuela.

Jan 1, 1941

By M. J. Blackburn

The phasal equilibria in TI&apos;:Al alloys has been studied Ry transmission electron microscopy, electron diffraction, and X-ray diffraction. It is shown that three-phase fields exist below the transformation, viz.: a disordered hexagonal solid solution a; an ordered hexagonal phase based on Ti3Al, aa; and a two-phase region. (a + (YZ) , occurring between the single-plzuse fields. The size. disiribution, and morphology of- the a, phase in the two-phase region is shown to be dependent upon the alloy composition and heat treatement. The ordering process in the a, phase leads to the formation of anliphase domain boundary networks; the contrast and stability of these networks is shown to be dependent on alloy composition. A new and relatively simple phase diagralil for the systemm is constructed. The phasal equilibrium at the titanium-rich end of the Ti:Al system has long been the subject of considerable controversy. crossleyl has recently reviewed the phase diagrams that have been advanced for the system and in his turn proposed yet another one. There would seem to be general agreement that a phase exists at a composition at or near Ti& with an ordered hexagonal DO,,-type structure. However, several other phases have been proposed; for instance, Ence and ~ar~olin&apos;s&apos; diagram includes two phases, Ti2A1 and Ti3A1, in the region up to 25 at. pct Al. The position of the proposed phase boundaries varies over a considerable compositional and temperature range, a point graphically illustrated in Fig. 1 of Crossley&apos;s paper.&apos; It is perhaps germane to briefly examine the techniques used by other workers in the establishment of the phase structure. These fall into three categories: 1) X-ray diffraction, the only limitation of which is the rather low intensity of superlattice reflections in this system.3 Thus, superlattice reflections become increasingly difficult to detect in the more dilute aluminum alloys. 2) A considerable amount of optical microscopy has been performed"2&apos;4 and it will be shown in a later section that many of the obscure mi-crostructures that have been observed can be attributed to hydrogen contamination. It is concluded, therefore, that such observations should be interpreted with considerable care. 3) The variation of some physical property with aluminum content has been measured.5"7 These methods are a useful indication of the existence of a transformation, but are usually insufficient in themselves to identify the transformation. The results using these techniques will be considered in more detail in the discussion. In this paper, the phase structure of alloys containing up to 25 at. pct A1 has been studied by transmission electron microscopy and X-ray techniques, and the results are used to generate a new and relatively simple diagram for the titanium-rich end of the Ti:Al system. EXPERIMENTAL A series of alloys containing 5.05, 10.16, 13.39, 13.99, 14.40, 20.83, and 25.05 at. pct A1 were obtained in the form of hot-rolled sheet 0.02 in. thick. These alloys contained 0.10 to 0.15 pct 0. Thirty-gram arc-melted buttons were prepared from iodide titanium and 99.99 A1 which contained 16.1, 16.9, 18.2, 19.0, 21.6, 22.2, 23.0, and 23.9 at. pct A1 and had an average oxygen content of 0.03 pct 0. The differences in oxygen content did not appear to influence the nature of the phase transformations which were found. Oxygen content may affect the temperature of these transformations, but insufficient samples of the high-purity alloys were examined to answer this question. The heat treatment of alloys was performed in dynamic atmosphere and vacuum furnaces or in helium -filled silica capsules. A special vacuum furnace was constructed to provide a high quenching rate in which rates of 4000°C per sec were obtained using water as the quenching medium. As pointed out by Crossley,&apos; it is important to avoid heat treatment in the a - [} phase field as the resultant segregation of the alloy into the two phases containing different amounts of aluminum can persist through subsequent treatments leading to ambiguous results. It will be demonstrated later that step cooling of specimens from the a phase region can also lead to anomalous effects. Thus, all solution treatments were carried out in either the a or 3 phase fields followed by water quenching and subsequent isothermal annealing at various temperatures. X-ray analyses were performed on a diffractometer on fine-grained bulk specimens. The value of long-range order parameter, S, wa_s calculated from the integrated intensity of the (1211) reflection. In general, the intensity of the (1011) superlattice reflection was compared with that of the (2021) fundamental reflection to correct for experimental differences between measurements. Thin foils for electron microscopical examination were produced by electropolishing using the technique described in an earlier paper.8 Dark-field techniques were employed to a large degree in this investigation using the gun-tilt method. Finally it should be noted that the lattice parameters of the D01,-type superlattice are approximately related to the disordered hexagonal phase parameters by Crf - c, and 2ad - a, where the subscripts s and d refer to the ordered and disordered unit cells, respectively.

Jan 1, 1968