Search Documents

By Steven Wright

The reduction of a slag produced 6om the recycling of lead batteries was studied in a kilogram scale laboratory investigation by reacting with graphite at temperatures of 1180 and 1200°C. Simultaneous reduction of PbO, Fe203, Sb203 and As203 occurred with the Sb and As reporting to the metal while the lead content in the slag was above 2 wt%. The Sb and As distributions between metal and slag were strongly affected by temperature and slag oxidation state. The rates of reduction of PbO and Sb203 increased with increasing slag basicity and temperature and decreased as the PbO content in the slag decreased. The reduction rate of PbO from these slags was similar to other industrial lead slags at the same CaO/SiO2 ratio and temperature. The implications of the behavioural similarities of the antimonous slags during reduction with carbonaceous reductants and other lead slags are briefly discussed.

Jan 1, 1994

By Carlos Maurício. F. Vieira, Lázaro A. Rohen, Sérgio N. Monteiro, Rafael G. de Castro, Gustavo X. Borges, Maycon A. Gomes, Frederico M. Margem, Anna C. C. Neves

Economic and environmental benefits are motivating studies on natural fibers, especially lignocellulosic extracted from plants, have been studied to substitute synthetic fibers, such as glass fiber as reinforcement in polymer matrices. By contrast to synthetic fibers, natural fibers have the disadvantage of being heterogeneous in their dimensions specially the diameter. About the hemp fiber, little is known of their dimensional characteristics. The aim of the present work was to statistically characterize the distribution of the diameter of hemp fibers. Based on this characterization, diameter intervals were set and the dependence of the tensile strength of theses fibers with a corresponding diameter was analyzed by the Weibull method. The diameter was measured with precision using a profile projector. Tensile tests were conducted on each fiber obtain mechanical strength. The results interpreted by Weibull statistical showed a correlation between the resistances of the fiber to its diameter.

Jan 1, 2015

By V. B. Chernyavsky, Ladokhin S. V.

Equipment and continuous casting technology for the production of small diameter copper rods and tubes are described. Industrial copper wastes, such as scrap and shavings, were used as the charge. An electron-beam installation for rod and tube production includes a crucible with an electromagnetic stirring system and a pouring hole in its bottom, a bottomless mold, .and a special cooling system, which includes an oil and water cooling devices. For the first time in the electron-beam technology, rods of 8 mm and 14 mm diameter mm tubes of 14 mm external diameter and 7 mm internal diameter were produced through continuous casting by pulling them out of the vacuum chamder into the atmosphere with depressurizing the vacuum chamber. The production capacity of a single strand continuous casting machine was 200 mm/tnin for rod casting and 150 mm/min for tube casting.

Jan 1, 2000

By Pedro A. Netto, Sergio N. Monteiro, Foluke S. de Assis, Rômulo L. Loiola, Frederico M. Margem

Banana fibers are among the lignocellulosic with great potential for use in polymer composites, such as the variety from the Musaceae family, due to its low density and good mechanical properties. In this work, epoxy matrix composites incorporated with continuous and aligned banana fibers were tested for their flexural behavior. Specimens with up to 30% in volume of fibers were bend-tested until rupture. The results showed an increase in both the composite mechanical strength and the stiffness with incorporation of these fibers. A fractographic analysis by SEM examinations a moderate adhesion mechanism between the banana fiber and the epoxy matrix. This mechanism is apparently responsible for the improved performance of the composites.

Jan 1, 2015

By Masahiro Sasaki, Wu Kepeng, Chang-Yong. Kang, Kohji Okada, Naohiro Igata, Kazuya Miyahara

"The damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys has been investigated. Particularly the effects of microstrucutre composed of the phases of a , a ' , y , and e on the damping capacity have been clarified. Various fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 mass % Mn and 50% cold rolling formed the largest volume fraction of e martensite and showed the highest damping capacity. The other phases of a, a' and y had very small effect on the increasing of damping capacity.IntroductionFe-Mn alloys are known to be one of the high damping capacity materials [l-3]. In the present research, the damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys, in which 12% Cr is added for the improvement of corrosion resistance of the Fe-Mn alloys, has been investigated. Particularly the effects of microstrucutre composed of various phases of a (bee), a ' (bet martensite), y (fee), and e (hcp martensite) on the damping capacity have been clarified. The results of preliminary research on Fe-Cr-Mn alloys are reported by Igata et al. [4] Various volume fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 % Mn and 50% cold rolling formed the largest fraction of e martensite and the measurement indicated clearly that e martensite had the largest effect on the damping capacity. The other phases of a ' y and a I had very small effect on the increasing of damping capacity."

Jan 1, 2000

By Lisa E. Helberg

"Titanium tetrachloride is produced through the chlorination of a variety of titanium bearing ores, some occurring in nature, and others enriched in titanium content by a variety of ""beneficiation"" processes. The chlorination step can produce a variety of metal chloride impurities, such as iron chlorides and vanadium chlorides, which must be removed from the TiC14 before it can be used to produce pigmentary TiO2, titanium metal or for any other commercial use. The requisite manipulations involve both physical and chemical separations in a multi-step process. The history of various purification strategies will be discussed.TextThere are a wide range of titanium-based products available, all of which start with titanoferrous ore of some type. Two main routes are used to convert ores into products, known as the sulfate and chloride processes. The sulfate process uses sulfuric acid to digest the ore, separate the impurities, and then precipitate titanium dioxide from the resulting titanyl sulfate (TiOSO4) via metatitanic acid. This process can also supply TiOS04 for other applications."

Jan 1, 2011

By C. M. Iheagwara

This paper has addressed the issues that constitute major obstacles to the cost- effective and efficient operation of metallurgical vessels from the refractory standpoint. Refractories generally withstand severe conditions of high temperature reactions as well as physical loading/impingement and hence degenerate and need replacement. Scarcity of some refractory materials especially high alumina and magnesite ores in some places, the prohibitive cost and the frequency of replacement of damaged refractories threaten the continued support for metallurgical operations. Some of the causes, prevention and cure for refractory wear have been discussed and rational strategies (short and long term) have been recommended which if implemented should go a long way towards arresting the perennial problems they portend.

Jan 1, 1991

By W. John Rankin

The finite and non-renewable nature of mineral resources poses unique challenges for sustainability: How can mineral and material needs of society be satisfied indefinitely? How can the benefits of exploitation of minerals best be captured for present and future generations? How can the environmental problems caused by large scale mining and processing best be ameliorated? These issues are rarely addressed, or if so only incidentally, in traditional courses in geology, mining, metallurgy and materials yet addressing them will increasingly be a major role for professionals in the minerals and materials industry and related sectors and agencies. This paper describes a framework for examining these and other sustainability issues related to meeting future material needs from non-renewable resources. The framework may be useful for educational purposes, either as the basis of a dedicated subject or by including the elements of it throughout a traditional course in relevant subjects.

Jan 1, 2014

By Wentao Guo, Xuefeng She, Qingguo Xue, Jingsong Wang

By the coke gasified reaction device and online measurement high-temperature compressive strength apparatus, the variation of pore structures of coke after gasified reaction with CO2 and H2O was investigated. Research illuminating the influences of solution loss rate, temperature, and carbon species on compressive strength of coke was also carried out. The results showed that the total compressive strength was higher than for the reaction with CO2. The high-temperature compressive strength of coke decreased with the increasing of solution loss ratio or temperature after reacting with CO2 and H2O. At the same solution loss ratio, the damage of pore structure to coke strength after gasified reaction with H2O was relatively smaller and the deformation resistance was stronger when compared with that in CO2.

Jan 1, 2016

By W. G. Davenport

Chapter 11 determined the combinations of industrial oxygen, oil and blast preheat that will steadily produce 65% Cu matte from pure chalcopyrite concentrate. It showed that the . combinations are described by a flat plane. It also showed that the minimum energy requirement for making 65% Cu matte occurs with maximum oxygen enrichment, zero oil and zero blast preheat. This chapter examines the, effect of matte grade on industrial oxygen, oil and preheat requirements.

Jan 1, 2001

By Milton Syamujulu

In 2004, KCM Nkana Smelter commissioned a 1200 tonne per day flash dryer and associated dry concentrate transport and injection system on the existing Teniente Modified converter (CT) unit. The aim was to upgrade the existing smelting unit, increase copper output and improve energy efficiency. This paper reviews the design, installation and commissioning phases of the introduction of this new technology and also discusses the initial two years of operating results for both the flash dryer and injection system at Nkana.

Jan 1, 2006

By Z. Y. Xie

The visualization techniques were employed for the analysis of computer simulation studies of dislocation core structure in ordered alloys. Atomistic computer simulation was used for the study of the local configuration of the material in the vicinity of the dislocation. Stresses were applied in the simulation in order to study the necessary stress level for the dislocation to move and onset plastic deformation of the material. The results were analyzed in terms of the strain tensor as a function of the position (x, y) in the material with the dislocation located at (0, 0). Various visualization packages are used to plot the invariants of this strain tensor and to visualize the changes that the dislocation core undergoes under stresses until it finally moves.

Jan 1, 1993

By Ennio Bonetti

The technological applications of MgH2 hydrides for hydrogen storage demand the overcoming of some critical issues: an improvement of the reaction kinetics and a reduction of the desorption temperature. The synthesis of nanocrystalline MgH2 by reactive milling and inert gas condensation and a proper metal catalyst addition, constitute recently employed strategies. In the investigation of the hydrogen short and long-range dynamics, sorption kinetics and nanostructure stability, the mechanical spectroscopy offers some specific advantages. In the present research this technique was employed with other experimental approaches (XRD DSC) to investigate relaxational and structural damping processes in nanocrystalline MgH2 with added catalysts (Fe). Time/temperature variation of the dynamic elasticity moduli and mechanical quality factor are correlated to hydrogen anelastic relaxation processes and concomitant structural transformation of MgH2 to Mg associated to long range H diffusion. Results are discussed with reference to microstructural modification strategies able to assist hydrogen release.

Jan 1, 2006

By John A. Gisby

Phase equilibria for multi-component systems can be calculated reliably from critically assessed thermodynamic data for sub-systems using software packages like MTDATA, developed by the National Physical Laboratory, UK (NPL). Models and data resulting from an ongoing Mineral Industry Research Organisation (MIRO) project make such calculations possible for the complex systems encountered during sulphide smelting, involving interactions between matte, slag, metal, and gas phases. Predictive calculations can be made that are directly relevant to industrial processes, covering composition and temperature ranges beyond the scope of hard- copy phase diagram compilations, allowing the feasibility of more economic and environmentally sound routes to be explored, better choice of materials to be made, and pilot plant studies to ,be directed more efficiently. Current applications include the selection of suitable fluxing practices in copper and nickel smelting, analysing the operation of the Kennecott copper smelter, optimising the recovery of precious metals and investigating refractory wear.

Jan 1, 2002

By M. M. Coleman

An investigation of the behaviour of sphalerite, chalcopyrite, galena and pyrite during flotation was conducted on selected circuits in the Brunswick Mining and Smelting Corporation Ltd. concentrator in Bathurst, NB. Samples were collected from 59 locations and analyzed for Zn, Pb, Cu, Ag, Fe, As, Sb, Sn, Bi and S. Metal balances were computed using the CAMP Material Balance Program (MATBAL 5) and the metal recoveries for each cell and circuit were calculated. An automated image analyzer interfaced with an electron microprobe was programmed to measure the size of sphalerite, chalcopyrite, galena and pyrite grains in each sample. The percentage of each mineral occurring as free grains and the relative amount of each mineral present in binary and ternary particles was calculated. The recoveries and losses of Pb, Zn and Cu are compared with the amount of liberated and unliberated galena, sphalerite and chalcopyrite present in the concentrates and tailings.

Jan 1, 1989

By John R. Hugens

Modifications in the ALSCAN method of measuring hydrogen dissolved in liquid aluminum have made it possible to monitor the level of hydrogen dissolved in liquid copper. Measurements from the tundish show a correlation with eddy current readings from the continuously cast and rolled copper rod from the continuous casting and rolling system at Amarillo. The measurements also indicate that the copper in the tundish is supersaturated with hydrogen.

Jan 1, 1994

By M. Jennings

In 1987, Echo Bay discovered a major silver/gold ore body at their McCoy property in Nevada, and quickly made a decision to build a 5000 tpd mill which was expanded during the design to 7500 tpd. Since the ore reserves consisted of cyanide leachable oxide as well as sulfide, the plant flow sheet involved an oxide leach, a gravity circuit, and lead sulfide and a pyrite sulfide recovery by flotation. The paper describes the process development, equipment selection, plant design and the startup of the oxide treatment.

Jan 1, 1990

By Lin Yang, Yuanbo Zhang, Zhuoxuan Li, Guanghui Li, Jinghua Zeng, Tao Jiang

A technique has been proposed for recovering iron from hematite-rich diasporic-type bauxite ore in this study. Direct reduction roasting followed by low intensity wet magnetic separation process was carried out. The parameters including reduction temperature and time, sodium salts, grinding conditions and magnetic field intensity for separation of iron were determined. The optimum process parameters as follows: roasting temperature of 1050 oC, time of 60 min, sodium salts involving sodium sulfate, borax, sodium carbonate with dosages of 10 wt%, 2 wt%, 35 wt% respectively, and magnetic field intensity of 1000 Gs with fineness of pulp reached 92.75% passing -0.074mm. Under the optimal conditions, an iron concentrate containing 88.17% total iron grade and iron recovery of 92.51% was obtained, 4.55% total iron grade in tailings. This novel technique provide a potential route for utilizing hematiterich diasporic bauxite ore, recovering iron resource firstly, and extracting alumina from magnetic separation tailings further.

Jan 1, 2015

By W. G. Davenport

Chapter 4 examined Inco (oxygen) flash smelting of pure chalcopyrite concentrate. It showed that the oxygen and flux requirements for auto thermal smelting are readily determined by a matrix calculation. This chapter extends this matrix approach by applying it to a multi-mineral concentrate.

Jan 1, 2001

By R. J. Wesely

In recent years the trend in copper smelting has been to expand existing smelters to increase their throughput. New smelters under consideration are large, typically in excess of 200,000 tons per year of copper. Despite this trend to larger smelters there are a number of conditions where a much smaller smelter can be economically viable. This paper examines these conditions and outlines the process concepts for a small smelter treating from 20,000 to 100,000 tons per year of copper.

Jan 1, 2000