Search Documents

By Anatoly Sudnev, Vladimir Skorohodov, Igor Kudryavtsev, Boris Radionov, Dmitriy Panov

"In cobalt production technology at a stage of solutions purification manganous cake (slime) basically containing hydroxides of the specified metals is formed. The possibility of full cobalt recycling in the basic technology of metal production at slime processing with generation of pure manganous compounds is shown. After slime dissolution in sulfuric acid in the presence of reducers the solutions containing cobalt, manganese, nickel and other nonferrous metals are formed. Optimum conditions of selective precipitation major part of cobalt by sodium hydroxide from the obtained solution are defined, thus more than 95% of manganese are remained in the solution. The cobalt precipitate is directed to the basic technology and the solution is purified by sorption. The most effective sorbents are chosen, optimum modes of its use are found. Examples of manganese recovery from the purified solutions as MnO2, MnCO3, Mn(OH)2 with a ratio manganese : impurities more than 3000 are presented.In the processes of hard alloys manufacture and processing of cobalt-bearing primary raw materials various cobalt-manganous slimes are formed. After leaching by solutions of mineral acids the problem of cobalt and manganese separation becomes an actual. The common way of metals separation in a solution is the Shreyber’ alkaline method allowing rather selectively to precipitate of cobalt hydroxide by sodium hydroxide. However this way does not allow separating completely target metals because of transfer of some manganese in the hydrated precipitate, even at its rather low content.In the given work the results of researches to improvement of a traditional way by inclusion to hydrometallurgical technology of operation of sorption separation of the specified metals are presented. The main goal is definition of conditions to achievement of the complete removing cobalt at hydrolysis with the minimum sedimentation of manganese and the subsequent additional recovery of cobalt by ionites from the obtained solutions."

Jan 1, 2008

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By R. T. Hernández, I. Hilerio, A. Altamirano, M. A. Barrón

"The principal objective for finishing surfaces is to protect and/or to decorate them. This can be achieved by adding or removing material from the work surface. The addition of aggregated material is called coating or recovering. In this work, mecano-chemical techniques are investigated for surface finishing. For these techniques, barreling or polishing by the friction method will be used. These are the cleaning or finishing processes most used for great volumes of small pieces. These methods improve the surface finishing by eliminating burrs, sharp pointed, tool marks and crusts of casting. They are used to clean metallic pieces, ceramics and polymeric materials. The process is based on rubbing or friction by abrasives. The pieces are arranged in the barrel with an abrasive and an additive (water or chemical additive). The machine produces a rotating movement on the pieces. When the abrasive passes against the surfaces of the pieces, it produces an action of rubbing and impact that cleans the surfaces. The rubbing action is developed when the upper layer of the charge slides to the lower extreme when the barrel rotates. The barrel can be hexagonal or octagonal to facilitate the sliding of the charge. The barrels can be between 15 to 120 cm in length and they can have almost any diameter and velocity of rotation. There are several types of barrel: individual, multiples, and multiple compartments. The barrels are rotated using a wheel spindle or rolling pins, that the can ride horizontally or be tilted to produce an additional movement of the charge.IntroductionShot penning is a cold method in which compressive effects are induced on an exposed surface of a metallic piece, by the impact of a rain of shots directly on the surface of the metal, at great speed under controlled conditions. This differs from cleaning with the help of air, because even when shot penning cleans the surface of the metal, this function is incidental. The main purpose of shot penning is to increase the resistance of the piece to fatigue. The process has other applications: raises the tensile strength and decrease corrosion fracture."

Jan 1, 2012

By Marcel Sturzenegger

Though the extraction of copper is well established, generation of sulfur dioxide (S02) is still a troublesome issue. Conventional processes are further challenged by the increasing amount of impurities in the concentrates. Direct decomposition of the metal sulfides into the metal(s) and elemental sulfur under concentrated solar radiation offers a promising path to solve both problems. Thermogravimetric measurements under inert atmospheres have shown that synthetic chalcocite or chalcopyrite yield copper at temperatures as low as 1773 K. Even though optimum reaction temperatures might be somewhat higher, such temperatures are straightforwardly accessible in solar chemical reactors. The absence of oxygen will reduce the extent of slag forming reactions and thereby alter the evaporation characteristics of volatile impurities such as arsenic or antimony. Chemical equilibrium calculations for a chalcopyrite-enargite feed, e.g., have shown that under inert atmospheres arsenic compounds are completely evaporated at temperatures above 1000 K and an effective separation of arsenic from the matte is expected. An important step towards a solar production of copper is the design and testing of prototype solar chemical reactors for this reaction. Numerical modeling is a key tool supporting a rational design but it requires data of the high-temperature properties that prevail in these processes. Development of techniques for determining the essential quantities such as decomposition rates or radiative properties at temperatures up to 2000 K is therefore a main activity in our laboratory in order to control and optimize the process. Though developed in the frame of high-temperature solar technology, the experimental techniques are also suited to advance the understanding of conventional high-temperature processes. Keywords: Solar technology, Sulfur dioxide, Solar Radiation, Thermogravimetry, Chalcocite, Chalcopyrite, Numerical modeling.

Jan 1, 2003

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Jr. Brown, A. Calderara, A. L. Antozzi

"The result of extensive research into fundamental mixed metal oxide catalyst morphology has produced a next generation all titanium Dimensionally Stable Anode (DSA ®). This new DSA ® anode, patent pending, is tailored for electrowinning of non-ferrous metals (copper, nickel, cobalt, zinc) by means of this new coating technology.These DSA ® anodes are characterized by a hanger bar with vertical distributor bars, having primary titanium mesh attached by weldments. The active mesh is provided with noble-metal electrocatalytic coatings, consisting of iridium and/or ruthenium oxides, obtained by thermal decomposition of precursor solutions applied to the titanium substrates. The catalytic activity of state-of-the-art DSA ® anodes is increased by controlling the crystallite size of the noble-metals without decreasing the decomposition temperature. It is known that below a certain value (typically 400°C) the stability of these oxides, and associated lifetime, is seriously compromised. A highly active DSA ® anode, consisting of a quasi-amorphous phase, is obtained at high temperature (above 450°C), therefore not compromising lifetime performance. Through optimization of these design parameters, the manufacture of these novel anodes was identified.DSA ® anode performance advantages include: lead-free ' green' all titanium anodes, true leadfree cathode quality, energy savings of 0.3 to 0.55 V can be realized depending on the EW application when compared to industry standard lead-alloy anodes, eliminate need for cobalt sulphate addition required for lead anodes, sustainability designed into long-life recoatable anode structures, increase plant cathode output through increased current density operations, improve plant on-stream production, no sludge generated or removed, and improve current distribution producing smooth high efficiency cathode.Introduction of ProductThere are many factors to consider when engineering a high performance DSA ® electrowinning anode. Half of the anode's performance is derived from the physical attributes of the electrocatalyst and methods employed when applying this catalyst to the titanium anode structure. The other half of the performance benefits relate to the proper structural design of the anode. In this paper, we will highlight the anode development program in which De Nora has invested to provide the Electrowinning marketplace with a high performance anode product."

Jan 1, 2012

By Jonathan M. Berkoe

Design engineers and metallurgists have long recognized the need for better methods to calculate a wide range of fluid dynamic effects in smelters and hydro- metallurgical facilities. Examples can range from the capture of fume in the secondary hoods of a copper converter, to controlling the thermal effects of heat transfer resulting from metal and slag flows within a furnace. With the advent of relatively low-cost, high- speed computers and user-friendly, commercially available computerized fluid dynamic (CFD) programs, these calculations can now be made. Use of CFD increased the understanding of both hot gas and molten flows in smelter facilities and has already led to design improvements in converter fume control hoods as well as improved management of heat transfer in electric furnaces. This paper will present two representative CFD applications to metals industry facilities. To date, Bechtel has implemented CFD results on four continents.

Jan 1, 1999

By Yiming Rong, Gang Wang

"Water quenching is one of common heat treatment processes but with complex physical phenomenon, in which vaporizing, bubbling and convection are involved. The general simulation of liquid quenching processes is conducted by using temperature dependent value of heat transfer coefficient (HTC) obtained from experimental measurement under a strong assumption. A preliminary multiphase flow model developed by using Ansys-CFX for water quenching has been presented in this paper, which shows a distributed HTC with a time dependent feature. The conjugate heat transfer is used to describe thermal conduction in the simplified workpiece, and generation, growth and flow of bubbles are modeled by using Eulerian-Eulerian method for the gas-liquid multiphase flow. The simulation result shows the intense variation of heat exchange through the interface between workpiece and liquid, and the unsteady distribution around the solid surface.IntroductionQuenching is a rapid cooling process which makes the desired solid phase transformations happen for the certain material properties. For aluminum alloy, rapid quenching will prevent all phase transformation and generate a supersaturated single phase."

Jan 1, 2012

By J. L. Delplancke

During copper electrowinning in sulphate electrolyte, intense oxygen evolution takes place at the anode. Lead alloy anodes are progressively replaced by dimensionally stable anodes in order to avoid the cathode contamination by dissolved lead. The electroactive coating of these anodes has to be as cheap as possible, adherent to the substrate, electrochemically stable and has to be efficient at high current density and high temperature. This requirement is even demanding in case of copper electrodeposition for the production of thin copper foils for the electronic industry. The production of thin (20 µm thick) copper foils for the printed circuit boards requires high purity copper electrodeposited at a current density as high as 7,000 A/m2. The choice of a long term coating composition is driven by economics. The purpose of this paper is mainly to review the anode compositions suitable for copper electrowinning and for copper electrodeposition at high current density. A short description of preliminary results obtained with a new anode coating on a titanium substrate is also presented.

Jan 1, 1999

By Jens Kristen Laursen

In 1999, Molymex S.A. de C.V. (Molymex), Mexico. (a company wholly owned by Molibdenos y Metales S.A. (Molymet), Chile) decided to install the Haldor Topsrae Wet gas Sulphuric Aicd (WSA) process for cleaning of the 4-5% SO2 off-gas from their molybdenum sulphide master in Cumpas, Mexico to produce sulphuric acid. The decision to install a WSA plant was based on the successful operation of a WSA plant at Molymet's molybdenum sulphide roaster in Santiago, Chile since 1993. This paper describes the process layout of the Cumpas plant, the operating experience of the Santiago plant, and the, differences in. process design between the two plants. It will furthermore summarise the applications of the WSA process for other roasting plants and smelters within the non-ferrous. metals industry producing metals such as copper, lead, and molybdenum.

Jan 1, 2002

By M. Cross, K. Pericleous, A. Mouchmov

"Copper - nickel - sulphide alloys are typically cooled and solidified in 4, 8 and 16 tonne ingots. These ingots exhibit a variation of grain size distribution and macro segregation of the prime alloy components throughout. The former is assumed to be primarily due to the dominant relation between grain growth rate and the cooling profile, whilst the latter is heavily influenced by buoyancy driven residual convection. The objective of this research program is to examine the extent to which it is possible to develop a 'broad brush' computational model of this ingot cooling process, that can predict some 'integral' measure of the grain size (e.g. average diameter) and the macro-segregation as a function of operating conditions.A computational modeling software framework, PHYSICA+ is used to simulate the complex process of ingot casting, which involves coupling between different physical phenomena. The entire model involves:(i) a 'broad brush' grain growth model that could be used in the prediction of micro/macro-structure of alloy ingot cooling processes,(ii) a heat transfer and solidification model which takes into account a second phase transformation of P NhS2 to heazlewoodite, and (iii) NS fluid flow simulation which provides a good basis for further micro/macro segregation modeling.At this stage some results of the 3D convection driven thermal cooling and solidification profiles will be shown, together with the 'integral' model for the grain size prediction."

Jan 1, 2001

By Jong-Oh Jo1

Thermodynamics of Ti, N and O in liquid iron was studied in order to establish a data base for the prediction of TiN and TiOx formation in liquid stainless steels containing various alloying elements including Cr, Ni and Si as a function of temperature. The interaction parameters of these elements on Ti and N were determined using the metal-nitride-gas equilibration technique. The TiN stability diagram for a commercial stainless steel grade was constructed from the measured thermodynamic parameters, and its validity was confirmed experimentally. The interaction parameters between Ti and O, and the equilibrium constants for Ti deoxidation reactions for the formation of Ti2O3 and Ti3O5 were also determined by the equilibration of the melts with those oxides identified by the XRD and the EPMA analyses.

Jan 1, 2006

By Ron Bernard

HW Process Technologies has successfully developed and commercialized various applications utilizing Engineered Membrane Separation (EMS?) systems for the processing of acidic copper hydrometallurgical solutions and wastewaters. Copper hydrometallurgical EMS? applications include water balance control and increased copper concentration in heap and dump copper leach operations, tankhouse bleed stream treatment to separate/recover copper and cobalt from iron, and removal of PLS/Electrolyte suspended solids/colloids to eliminate "crud" formation during copper SX/EW. Similar applications are underdevelopment to provide ionic separations in copper refinery bleed streams, copper smelter acid plant streams, as well as organic/LIX removal from aqueous electrolyte and raffinate streams. Copper mine wastewater EMS? applications include treatment of copper leach solution contaminated groundwaters for copper recovery and treatment of unwanted heap/dump drainage to provide enhanced precipitation, a smaller precipitation plant, improved operating costs and better quality discharge water, particularly in terms of TDS and sulfates. A discussion of the EMS? technology and general separation results on typical process solutions and wastewaters will be presented. HW Process Technologies, Inc. commercial installations treating copper pregnant solutions and leach solution contaminated groundwaters are in-place at an old Asarco smelter/refining operation, Mexicana de Cananea copper mine, and a major U.S. copper mine, with several additional installations pending. Several case studies, including results from a selection of these installations, will be included with detailed capital, operating cost, and system payback data.

Jan 1, 1999

By R. K. Hill

The Hidalgo Smelter successfully reduced operating costs by 25% compared to the previous two years through a focused holistic approach to development of its entire workforce. The first phase involved basic team training skills for natural work teams. The second phase provided leadership training via breakthrough education to 40 of the smelter leader-both hourly and salaried. The third phase stretched out the teams training to include rewards for performance that resulted in hourly teams converting to salaried status-part of a company wide initiative. The fourth phase saw 1998 become the "Year of Safe Cost Reduction" where 7 breakthrough projects focused on different areas of expenditure. Implementation of lean manufacturing as a tool for teams to truly get their arms around what they controlled, introduced accountability and responsibility for operating results at the team level. This will allow the release of experienced supervisors from this role, to a pool of technical expertise, where our future breakthroughs will be designed and implemented.

Jan 1, 1999

By María Guadalupe Sánchez-Loredo

Silver from nitrate aqueous solutions was extracted by commercial organophosphorous extractants (tri-n-butylphosphate, Cyanex 471x, Cyanex 301 and Cyanex 302). Quantitative silver extraction was obtained using the Cyanex reagents. After loading, aqueous solutions of several reducing reagents were used to prepare fine silver powders by reductive stripping. Only both extractants Cyanex 471x and tri-n-butylphosphate (TBP) could be reductive stripped and regenerated by aqueous solutions of ascorbic acid, and Cyanex 471x was decomposed to the corresponding phosphine oxide by using sodium borohydride as reducing agent. Silver was recovered as fine particles, which were characterised by means of scanning electron microscopy (SEM). Micrographs showed that the powder size and morphology were directly affected by the composition of the applied organic phases and aqueous reducing media.

Jan 1, 2003

By Huang Chao

The thermodynamics analysis on reducing-matting smelting of sulfide ore of lead, antimony and bismuth which use ferric oxide as sulfur fixed agent is first analyzed. Due to the analysis of reaction mechanism, ferric oxide is first reduced to ferrous oxide, then ferrous oxide produce reducing-matting reaction with sulfide ore and reducing agent as reaction equation: MeS+FeO+CO=Me+FeS+CO2. The reaction thermodynamic calculation shows that the reducing-matting reactions of lead sulfide, antimony sulfide, Jamesonite, and bismuth sulfide are feasible, but is infeasible for zinc sulfide. These conclusion provide a feasible method for solve the pollution which produced in the smelting of sulfide ore of lead, antimony and bismuth.

Jan 1, 2006

By G. F. Archer

Selenium and tellurium, trace metals found in copper smelting, report to blister copper during smelting. Winning these metals from anode slimes, the primary commercial source, is discussed. At Asarco's Amarillo Copper Refinery, slimes treatment segregates selenium and tellurium to a water-soluble soda slag. Aqueous precipitation of tellurium oxide and selenium by sulfur dioxide is valence dependent. Se+6 and Te+6, which constitute a portion of total selenium and tellurium, are not susceptible to this base case treatment. "Secondary Selenium" is formed from these hexavalent species. We describe a process whereby simultaneous oxidation of selenium and tellurium effects a separation. Process conditions for separating selenium dioxide, and efficiency of fume capture are examined.

Jan 1, 1995