Search Documents

By Li-min Liu

The Semi-Analytical method can be used to solve a variety of problems in geomechanics and civil engineering. When it comes to layered rock strata and rock masses, it is superior to all other analytical methods. This paper presents the application of a 3-D semi- analytical method to 3-D surface subsidence and stress analysis caused by mining. In this semi-analytical method the layered elements and triangular elements ate used alternatively. Their displacement pattern, strain mahix, elastic matrix, stiffiness matrix, load matrix and stress matrix are presented. A numerical simulation program based on the semi-analytical method bas been developed using Fortran 90. This program is suitable for subsidence prediction and stress analysis of mom and pillar mining, strip longwall and mechanized longwall mining methods. It is applicable to all geological conditions and mining methods. Comparing with the finite method, this method reduces significantly the number of simultaneous equations to be solved and the amount of data preparation. It not only reduces the computer memory, but also runs faster and cost less. Key Words Semi-analytical method, surface subsidence, stress analysis, layered element, triangular prism element

Jan 1, 2002

By Klaus-Dieter Beck

RAG American Coal Holding, Inc. affiliates operate two longwall mines in the Pittsburg seam in Pennsylvania, the Cumberland mine and the Emerald mine. A unique situation in longwall operation occurred at these mines as the mining activities reached the property boundary between the two mines. The retreat direction in the longwall panel in Cumberland mine is West-to-East while in Emerald mine, it is East-to-West. This unique condition required an adequate design for barrier pillar between the two mines to minimizing the mutual effects of longwall retreat when both longwall faces met and an adequate roof control plan for gateroads. Field studies that involved mainly roof-to-floor convergence monitoring were conducted to assess the effectiveness of the employed barrier pillar in isolating the mutual effect of longwall retreat. Three-dimensional finite element numerical modeling was used to evaluate the gateroad roof and pillar stability. The modeling was conducted such that it duplicated the actual mining process as realistically as possible. The modeling results predicted that the employed barrier pillar and the roof control plan would ensure stable gateroad systems in both mines during and after the two longwall faces met. The prediction was confirmed because mining operations in the two longwall panels were completed without any noticeable ground control problems.

Jan 1, 2004

By Mietek Rataj

Installation of pre-tensioned Strand Bolts i.e. resin grouted cable bolts is very common now in Australian coal mines. A short historical development of this type of rock reinforcement is outlined Various systems have been developed to apply 20 to 25 tonnes of pre-load to these bolts but there are still some technical problems which have to be overcome. One of the major problems encountered is bleed off tension which is highly undesirable as required "over loading" rocks the immediate roof thus inducing fractures iii weak strata. The major reason for the loss of tension apart from the design of the tensioning jack, is the design of the conventionally used barrels and wedges. Due to a roof plate tilting during tensioning the cable moves out of the barrel centre which impedes proper positioning of the wedges and subsequent excessive return of the cable once load of the jack is released. This problem has been largely resolved by the design of a special barrel having a centralizing rim allowing for significant reduction of the toss of tension. KEYWORDS: Pre-tensioned Strand Bolts, Cable Bolts, Bleed off Tension, Tensioning Jack, Loss of Tension

Jan 1, 2002

By Ebrahim Ghasemi

Roof fall risk is a common problem in coal mines, and it is generally unpredictable due to variability in geological and mining parameters. In this study, a new fuzzy logic model was developed to predict roof fall rate in coal mines. Parameters such as coal mine roof rating (CMRR), primary roof support (PRSUP), intersection span, and depth of cover were considered as the model inputs. The model was developed based on experts? knowledge and also a database including about 109 datasets of roof performance from U.S. coal mines. Approximately 20% of these datasets were used to assess the performance of the fuzzy model. In each case, comparison between results from model and real roof fall rate showed that this model can predict roof fall rate to an acceptable extent.

Jan 1, 2011

By Nikolaos Polysos

For the planning and driving of gateroads supported by roof bolts a practical concept has been developed in order to determine the geological and rock mechanical parameters derived from exploration drillholes. Based on this, an assessment scheme for the design of roof bolting has been established. The new methods of investigation comprise of geotechnical logging of drill cores for the determination of structural-geological rock characteristics and complementary geophysical well-logging which enables the evaluation of petro-physical and rock mechanical properties. The tools and their measurements will be briefly presented. The relationship between the geophysical log readings and the geotechnical parameters will be illustrated. The aim of the data acquisition is to improve roof bolting design which is based on the assessment scheme. This will be adjusted to the prevailing rock mechanical conditions and stands up to the required stability of the gate roads. In order to ensure consistent data acquisition, a method of core logging has been standardized for the respective demands. To achieve this it was necessary to introduce specific parameters and new methods. For the recording of linear and planar structural elements at the drill core, a special system for the documentation of the angles in relation to each other has been set up. The rock mechanical parameters and their acquisition will be explained. In order to carry out an objective analysis as fast as possible, software has been developed for the acquisition, management and presentation of the data. These programs and their functions will also be presented. The software is characterized by being user-friendly and the flexibility of its interfaces, Different options for the combined presentation of input and evaluated data give a more objective basis for the planning of roof bolt design. Examples will illustrate the operational implementation of the results during the planning and driving phases.

Jan 1, 2001

By Linsheng Xu

When coal seam is under the integral thick sandstone (or conglomerate), the structure of thick sandstone is integral and its strength is rather high. After coal is extracted, the roof is hanging and caving is difficult. When the method of full caving is adopted in the longwall working face to control this kind of hard and difficult caving roof, the effect of roof-controlling affects directly the production and safety. In China Datong Coal Mines the extracting coal deposit is Datong Jurassic period. Most of the roof is sandstone and conglomerate. It is hard and difficult to cave. Having used special hydraulic power supports and other special ways to deal with the roof, the hard and difficult caving roof has been controlled.

Jan 1, 1986

By M. Bouteldja

A finite element modelling approach is developed for the evaluation of the mechanical performance of cable bolts supports in underground mine structures. The modelling approach permits the simulation of any arbitrary number or pattern of cable bolts, that can be either partially or fully grouted, with or without end plates. The modelling technique used treats each cable bolt as a set of bar elements representing the steel cable. The bond stiffness characteristics of the grout bolt interface are represented by shear springs uniformly distributed along the cable length. Coupled with a simple linear elastic analysis, this technique can serve as a dedicated numerical model for cable bolted excavations. The application of the model is illustrated with two case studies: one for a hard rock mine and another for a coal mine.

Jan 1, 1999

By Kevin M. Connor, O&apos

An example application is presented in which Time Domain Reflectometry (TDR) was utilized to monitor roof strata movements during pillar extraction in a potash mine. The study was initiated when Western Ag-Minerals decided to implement secondary mining of pillars in order to extend the life of their Nash Draw Mine. A prototype operation was conducted in one mine panel to assess mining equipment and procedures, and to determine if ground control problems would develop. An instrumentation array was installed by personnel from New Mexico Tech and Western Ag to monitor strata movements, changes in pillar stress and surface subsidence, and these data are being analyzed by the Bureau of Mines. This paper is limited to a discussion of roof-floor convergence and roof strata movement to illustrate the application of TDR to ground control. Plots are presented which demonstrate the capability of distinguishing location, magnitude and mode of rock movement using TDR to interrogate coaxial cables grouted into holes drilled in the roof.

Jan 1, 1990

By Axel Preusse

Stowing or waste fill is common in the German mining industry since the beginning of mining activities, With increasing mechanization, flat and gently inclined seams (0 -- 18) were mined. These mines were located within the densely populated areas close to important infrastructures such as industrial complexes, roads, highways, railroads, rivers and canals. These buildings and infra¬structures were rarely protected against subsidence influences and other ground movements and dump capacities close to the mines were exhausted. For subsidence reasons and because of the low dump capacities pneumatic stowing methods were continuously developed and used in German longwalls until 1997. Due to techni¬cal standards and because of some restrictions pneumatic stowing in Germany is only used at a minimum seam thickness of 2.00 m and average costs of this method are $20 - 30 per ton. A significant reduction of the disturbance potential and by that a decrease in expenses for subsidence regulations due to reduced subsidence and ground movements could not be achieved. In this paper the experiences with pneumatic stowing in the Ger¬man mining industry are described. Possible subsidence reduction and economic aspects of pneumatic stowing are taken into account.

Jan 1, 2002

By Ken Barish

Jane Mine of the Keystone Coal Mining Corporation was started in 1962 and is in the Lower Freeport seas located in Armstrong County, Pennsylvania, approximately 45 miles northeast of Pittsburgh. The mine is a slope/shaft complex with the cover ranging from 100 feet at the slope to 450 feet near the back end of the property. The seam height ranges from 48 to 72 inches. A variety of roof conditions have been en¬countered, and an equal variety of roof control systems have been tried with varying degrees of success. Initially, places could be mined as deep as 100 feet without any permanent roof support. After several problems and the advent of the Health and Safety Act of 1969, roof control became more and more prevalent and predominant at the Jane Mine. It started with 4 foot conventional oolts. As the mine progressed in the northeasterly direction, roof conditions changed from the extremely good roof that was encountered initially, to bad roof; and other types of roof support were required. Sixty pound rails and 6 inch 25 pound to the foot steel I-beams were used for supplemental support in long life headings such as belt and track. Resin bolting was done in many areas for long life support due to the deterioration of the shale roof over time. Several areas had to be abandoned because of uncontrollable top.

Jan 1, 1984

By John Cassie

The condition of roadways in the Deep Main seam at Asfordby mine, operated by RJB Mining (UK) Ltd, is strongly dependant on drivage direction relative to the maximum horizontal stress. The mine is laid out with gate roads driven approximately parallel to the maximum horizontal stress giving favourable drivage conditions. This has led to particulary difficult conditions for face installation headings which have to be driven to an increased width and at a high angle to the horizontal stress. A solution to the formation of face headings is described making use of stress relief with the face heading being driven in the zone of reduced stress surrounding a previous heading. In implementing this solution use was made of results from computer modelling and detailed monitoring of roadway behaviour. High reinforcement densities including cable bolts were used in supporting the headings. The experience provides an example of a traditional technique being applied more scientifically. The results obtained demonstrate the effect of stress relief and reinforcement methods in altering drivage conditions and suggest possible alternative strategies for the formation of future face headings in these conditions.

Jan 1, 1997

By S. P. Singh

Destress blasting is commonly used in the mines to minimize the occurrence of rockbursts. The fracturing created by destressing in the vicinity of the face reduces the stress concentration by pushing the zone of high stress deeper into the rock mass. But the destressing practice by blasting may be devastating near the faults or other sensitive high stress zones. To avoid severe rockbursts in such situations, the application of chemical destressing has been proposed in this paper. A laboratory investigation was conducted on the rocks in the Sudbury basin to examine the change in the material properties with an aim of assessing the feasibility of destressing by chemical means. The favourable change observed in the rock properties led to the suggestion that the injection of surfactants in boreholes would enhance fracture propagation similar to what is currently done by blasting but in a safer, inexpensive and non-violent manner. The current destressing practices in Ontario mines have also been reviewed in this paper.

Jan 1, 1987

By Aarao de Andrade Lima

Mechanical properties typical of coal are used in the comparisons of pillar strengths based on finite elements and the empirical equations of Holland-Gaddy, Salamon-Munro, Obert¬Duvall, and Bieniawski-PSU. A correlation among the strength parameters which are employed in the empirical equations, in Mohr-Coulomb and Hoek-Brown failure criteria is established. Emphasis is given to the important distinction between the mechanical properties of small rock specimens and those related to the rock mass. An elastoplastic version of Hoek-Brown criteria has been developed and implemented in a finite elements code. The strengths calculated using the empirical equations showed a good agreement when the ratio width by height of the pillars varied from I to 8, except for Holland-Gaddy equation which exhibited lower values. Under the hypothesis of associative perfect elastoplasticity used, pillar strength calculated using Mohr¬Coulomb yield criterion became excessively high for all the models having a pillar width by height ratio above 2. The finite elements solution based on Hoek-Brown criterion predicted strengths around fifty percent larger than Bieniawski-PSU equation when the pillars width by height ration varied from 3 to 8, showing good agreement below that range. It has been concluded that, under the hypothesis of percfect plasticity, stress analysis techniques may overestimate the strength of rock structures subjected to high confining stresses.

Jan 1, 1997

By Hani Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in Bolts) has been recently developed. The device SAFEBOLT, essentially replaces the load cell, it permits the monitoring of bolt axial load from the time of its installation underground. The SAFEBOLT system consists of a portable readout unit, connecting cable and the SAFEBOLT device, which is installed in the bolt head. SAFEBOLT can be installed on any industry standard rockbolt. No special installation method is required; the conventional method of bolt installation by the stoper or roofbolter remains unchanged. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electrical wires. Pilot tests at three underground Quebec mines were carried out and helped improve the initial design of the device connector. The paper reports on two of such pilot tests.

Jan 1, 2001

By Bruce K. Hebblewhit

Australia is well endowed with extensive reserves of thick underground coal scams, particularly in the range of 4.5m to 9m thicknesses. (For the purposes of this paper, thick scams are defined as being greater than 4.5m thick.) At the present time, the thickest, high production, high productivity underground mining operation in Australia operates at a maximum of approximately 4.8m using single pass longwall methods. In a number of instances, conventional' height operations are mining thick seam coal, effectively sterilising considerable reserves - either because of financial or technical risk concerns, or in some cases poorer quality coal at some horizons in the scam, UNSW has been involved in thick scam mining research over many years, most recently through an ACARP -funded project, jointly with the CMTE in Australia. A key part of that project involved the assessment of the relative geotechnical risks associated with the various methods under consideration. The methods were: single pass longwall; multi-slice descending longwall; soutirage and related caving methods (including the Chinese Longwall Top Coal Caving method (LTCC)): and hydraulic mining. A formal risk assessment process was adopted to review the risks, relative to a conventional 4m high longwall operation. This paper presents the findings of that risk review and discusses the geotechnical issues (and some possible solutions for risk management) which need to be dealt with in order to bring these methods to fruition in the context of the Australian coal industry environment.

Jan 1, 2001

By Dieter Wittenberg

The use of thc ultrasound technique for monitoring rockbolt support has at last provided support engineers with a measunng system capable of pinpointing fracture failuns in fully-grouted rockbolts. The measurement data are based on the operatmg characteristics of the bolt type, which are determined both under test-bench conditions (DIN 21521) as well as in underground trials. Practical experience acquired to date suggests that this new measuring system is both effective and reliable.

Jan 1, 2001

By James J. Scott

Over the past two years research, development ad field tests have been conducted on a new product called the "Scott Cable Sling". This work resulted in the awarding of U.S. Patent No. 4265571 on May 5, 1981, to the inventor. Work on this' project was done by the staff of Scott Mine Technical Services, Inc., and is in keeping with its philosophy of advancing mine grad control technology. Recent acceptance by industry has resulted in volume purchases of the product and indications are that it will gain wide acceptance by the mining industry. The system features flexibility in its application and is useful in both roof and rib control. This paper describes the product, discusses its range of applications and cites specific field examples of its use.

Jan 1, 1981

By J. A. Nemcik

Although floor failure at longwall faces has been traditionally associated with a soft floor, in many csses floor buckling has been observed just ahead of the longwall supports, despite the floor being a competent rock The floor failure is associated with the presence of weak bedding planes in the floor and the movement of strata towards the goaf opening. This paper presents the principles of the floor failure based on numerical modelling and field observations and outlines the practical approach to estimate the risks involved with floor failure.

Jan 1, 1995

By J. R. M. Hill

The U.S. Bureau of Mines is involved in research to improve geological sensing (or geo-sensing) techniques. This paper presents results from field trials of two research projects concerned with new technologies for geosensing. The goal of the first project was to develop a "smart" roof bolter drill so that it could probe into roof rock to evaluate rock conditions. The goal of the second project was to modify an existing mine-wide monitoring system in a continuous mining operation so that the system could interface with geotechnical instruments to provide near real-time geosensing. Integration of this mine-wide monitoring system with the smart roof drill to collect, reduce, and analyze geotechnical data and the potential applications of the resulting technology in mining, are described.

Jan 1, 1992

By Winston Gale

This paper is presents a summary of recent investigations into fracture and caving about longwall panels. The results of these investigations indicate that rock failure initiates well ahead of the longwall face. Rock fracture typically forms in response failure through the material and bedding planes. Tensile fractures also form in massive units. These fracture patterns typically create a fracture network which determines the caving characteristics encountered at the faceline. The action of longwall face supports under such conditions is to maintain confinement to the fractured ground and develop a consistent caving line, The confinement developed above the canopy under these conditions can be variable on a shear by shear basis and the operational face support procedures play an important role in stability about the face area.

Jan 1, 2004