Search Documents

By Susan T. Bagley, Kenneth L. Rubow, David H. Carlson, Bruce K. Cantrell, Winthrop F. Watts

Permissible exposure limits (PELs) have been established for gaseous pollutants, carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), nitrogen dioxide (NO2), and some gas-phase hydrocarbons emitted in diesel exhaust. There is, as yet, no PEL recommended for diesel exhaust aerosol (DEA), nor is there a standard method for sampling this aerosol. The University of Minnesota and the U.S. Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size-selective inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were made in underground coal mines that use diesel equipment. The mine mean DEA concentrations for the five mines surveyed, determined with the PDEAS in the haulageway, was 0.89 mg/m3 with a standard deviation of 0.44 mg/m3. DEA contributed 52 % of the respirable aerosol at this location. In three of the mines filter samples were collected for DEAassociated polynuclear aromatic hydrocarbons (PAHs) and biological activity determinations. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust. In general, the PAH and biological activity levels were similar for all three mines, and indicate that up to 25 % of the haulageway concentrations may be contributed by outby diesel vehicles. Measured concentrations of CO, C02, NO, NO2, and SO2, were well below regulated levels. INTRODUCTION Diesel exhaust contains pollutant gases, such as carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and gas-phase hydrocarbons, as well as DEA. Much of the health-related concern focuses on DEA and associated organic compounds (Watts, 1992a). A wide variety of these PAHs have been identified and some are known carcinogens and/or mutagens. The U.S. Mine Safety and Health Administration (MSHA) has proposed new PELs for these and other contaminants (MSHA, 1989). MSHA has also published an advance notice of proposed rulemaking to establish a separate PEL for diesel particulate (MSHA, 1992). The U.S. Bureau of Mines has collaborated with the University of Minnesota to develop and field test a PDEAS. The PDEAS is a three stage sampler based on the MSA' personal respirable dust sampler. It utilizes a respirable cyclone preclassifier followed by a 0.8 µm cut point impactor and afterfilter operating at a flow rate of 2 L/min. Respirable aerosol greater than 0.8, µm in size is collected by the impactor while DEA, less than 0.8 µm in size, is collected by the afterfilter. Hence, gravimetric analysis of the afterfilter permits measurement of DEA concentrations. This development and laboratory evaluation of the PDEAS were described previously by Cantrell (1990) and Rubow (1990). During field tests of the sampler, numerous air quality measurements were made in continuous miner sections of five underground coal mines that use diesel haulage equipment. These air quality measurements included levels of selected PAH and biological activity associated with DEA collected in the intake and haulageway areas of three of the five underground mines, and CO, CO2, NO, and NO2 in two of the mines. The objectives of this paper are to present the DEA and associated pollutant concentrations measured in these mines and to assess the impact of diesel face-haulage equipment on underground mine air quality. MINE DESCRIPTIONS The mines used for the PDEAS evaluation were designated J, K, L, N, and 0. Mines K, N, and 0 are located in the Western United States, while mines J and L are located in the East. Each mine produces high volatile, bituminous coal with shift production levels varying from 500 to 2000 tons/section. Seam heights varied from 1.5 to 3.0 m. Mines K and N use continuous mining to develop longwall panels. The others are strictly room-and-pillar operations using continuous miners. The number and types of diesel-powered vehicles used at these mines were described by Watts (1992b). Mines J, K, N, and 0 use diesel power to assist in a wide range of activities in addition to coal haulage. These included road maintenance, personnel and materials transport, lubrication, and welding. Mine L used only three diesel-powered shuttle cars to haul coal. SAMPLING AND ANALYSIS METHODS Aerosol Measurements Aerosol samples were collected in the mine portal area, the clean air intake to the continuous miner section, the haulageway one crosscut inby from the feeder breaker and belt, in the return airway, and on selected personnel. The haulageway sampling site was located near the point where the diesel-powered shuttle cars turn around to dump their loads. Additional respirable and DEA samples were collected and have been reported by Haney (1990).

Jan 1, 1993

By K. Hanna

This paper describes a method to improve coal mine entry intersection design. The method considers the effect of in situ stresses, local geologic conditions, rock physical properties, and mining sequence. Development of the method is discussed, including the results of field instrumentation studies and numerical modeling investigations. Data required to evaluate the effects of roof span, mining sequence, entry orientation, and bolting patterns on intersection stability are also presented. Ground control studies conducted by the U.S. Bureau of Mines in two underground mines in the Illinois Coal Basin have shown that in situ horizontal stresses and roof geology have a critical effect on intersection stability. Methods to reduce the adverse effects of these parameters are emphasized. Typical failure behavior associated with specific geologic and horizontal stress conditions is' presented to illustrate proposed control methods to alleviate adverse ground conditions.

Jan 1, 1988

By D. A. Lee

The selection of control system equipment for a mineral plant is based on several criteria, including opera tor interface, supervisory capabilities, ease of maintenance, ease of programming and configuration, compatibility with auxiliary control equipment, and total cost. The paper discusses the technical evaluation procedure with respect to control system equipment available today.

Jan 1, 1988

By D. A. Stanley

The Bureau of Mines has developed an equation which describes the dewatering of clay slurries with polyethylene oxide. This dewatering equation is An _ kC + b where n, k. and b are empirical constants and C is the concentration of polymer solution used for dewatering. The minimum amount of polymer required for dewatering. A is determined by titration of the clay slurry with a polymer solution. In this report, the dewatering equation is applied to data obtained for a polyacrylamide dewatering sequence. Fundamental similarities between the dewatering properties of clays and the viscosity of polymer solutions were observed. These similarities were explained by correlating an equation describing polymer configuration in solution with the dewatering equation. This correlation showed that amount of polymer required for dewatering and polymer solution viscosity are both consequences of the frictional interaction of entangled polymer coils.

Jan 1, 1989

By Stephen P. Mulqueen

Searles Lake is an evaporite basin located near the community of Trona in northwestern San Bernardino County, CA. Searles Valley Minerals Operations Inc. (SVM), a subsidiary of Nirma Limited, currently manufactures more than 1.58 Mt/a (1.75 million stpy) of industrial minerals from natural brines produced from several lakebeds within the basin. The chemical manufacturing facilities in Searles Valley represent extremely complex operations involving solution mining and mineral extraction processes.

Jan 1, 2012

By James A. Berberick

Research methods to develop an economic model for the determination of regional mineral advantage are discussed. An industrial complex conceptual framework is used to study potential mineral resource outputs of Kansas. A procedure for making a comparative cost analysis of potential outputs for a Kansas-based industrial complex is outlined and illustrated. Methods for estimating aggregate demand and for developing an input-output matrix for a hypothetical limestone complex are explained. The input-output matrix is expressed in physical units. A computer algorithm for converting physical production data and input cost data into total cost per unit of output information is briefly explained and flowcharted. Limitations and usefulness of this procedure in determining regional advantages are surveyed.

Jan 1, 1969

By W. G. Pariseau

This paper is concerned with the problem of calculating ground movement that occurs as a consequence of mining. Solution to this problem is straight forward in principle but rather complex in practice. The complexities of the problem arise from the ever present constraints of technology and economics. However, the identity of these constraints is often obscured by a faulty understanding of the fundamentals of the problem and a lack of appreciation of current computational capabilities and costs. As a consequence much time and effort are sometimes wasted on gathering information that is of little direct value to ground control programs while important input data are neglected. This paper therefore reviews the essentials of the process of formulating the ground movement problem. Emphasis is upon application to longwall mining, although much of the discussion applies to other mining methods as well. In many instances, the hardrock term stope could be substituted for longwall panel because the fundamentals of the problem are independent of the excavation dimensions and numerical values of rock properties. The latter affect the outcome of a calculation, of course, but not the underlying formulation. Only the major features of the problem are discussed in this brief review. The objective of the discussion is the generation of a reliable basis for developing a technically sound ground control strategy. Any rational ground control strategy must be consistent with basic physical laws. For example, under static conditions, equations of equilibrium must be satisfied. Operational, that is, tactical, details may vary widely with local conditions, but the basic approach must be based on physical laws. The alternative empirical route is intrinsically unreliable and unnecessary as well. Empirical descriptions of ground motion caused by mining including recent statistical curve fits to specialized data sets (for example, surface subsidence data) as well as antiquated "theories" of ground pressure and so forth, however dignified with mathematical formulas, are hardly worthy of the label "theory". Extrapolation of statistical data is always accompanied by rapidly diverging confidence limits, while empirical equations simply lack predictive capability under circumstances even slightly different from those of the original development. For example, applications of surface subsidence curves generated empirically in the United Kingdom to coal mines in the United States generally result in considerably greater subsidence and wider subsidence troughs than actually observed. Locally, empirical criteria for specific ground control actions may be made practical through trial and error, but such tactics are no basis for the development of a general ground control strategy. In this regard, it is worthwhile to recall the traditional scientific distinctions between speculation, hypothesis and law, between the empirical and the proven.

Jan 1, 1982

By III Westbrook

Although calcium sulfate dihydrate, commonly referred to as gypsum, has been utilized for some time in fiberglass reinforced polyester (FRP) applications, it does not have the fire retardant filler recognition of ATH. Gypsum is more commonly known for application in cement, soil and water treatment, plaster, and wall-board. Inherent characteristics of gypsum limit its use to low temperature and, until recently, non-aqueous applications. However, as a plentiful, naturally occurring hydrated mineral, the cost effectiveness of calcium sulfate dihydrate has prompted development and yielded success in the areas of FRP spray-up and latex carpet backing.

Jan 1, 1993

By John D. Abbatt, H. B. Newcombe

The Eldorado Epidemiology Project formally began in late 1978. It consists of a retrospective cohort study, to be followed by and to leave in place the mechanism for a prospective cohort monitoring program. These present and future activities are intended to merge into one another. The current study includes all Eldorado employees past and present for whom records are available. The objectives of the undertaking are - 1) to obtain cause-and-effect, dose-response data with which to evaluate the risks to workers in radon and radon daughter containing atmospheres, and to provide additional quantitative information on which to base possible improvements in working conditions; 2) to identify any dead employees of E.N.L. whose cause of death suggests that a potential compensation claim right exists for their survivors, and to similarly identify living ex-employees of E.N.L. whose work histories and states of health suggest potential compensation claim rights. The nature of the study has been determined by the history of Eldorado, which will be described briefly. Eldorado began (as Eldorado Gold Mines) in the late 1920's, operating relatively unsuccessfully in Manitoba. In 1930-31 the emphasis shifted from gold to uranium, and what became the Port Radium mine was first staked. From the very early 1930's until 1942 the company's purpose was almost entirely devoted to the mining of pitchblende - uranium ore - from the Port Radium site, and the extraction of radium from this ore at the Port Hope refinery in Ontario, a process from which the uranium was a largely stockpiled byproduct. In 1942 the company was requested by the Canadian government to accelerate the production of ore, and of uranium. At the same time, all its stockpile of uranium (then being stored in silos as a "waste" product which might later "come in") was acquired for the Manhattan Project. In 1944 the company shares were bought by the Canadian government and the company itself became Eldorado Mining and Refining (1944) Limited; it has operated as a Crown corporation ever since. The name was changed to Eldorado Nuclear Limited in 1968. The Port Radium mine was closed in 1960, and since 1953 the Beaverlodge uranium mine complex has operated on the northern shores of Lake Athabasca. Radium production was discontinued in 1954 when the radium circuit was taken out of the refinery, and since that time the refinery's products have been various types of refined uranium (uranium dioxide, uranium trioxide and uranium hexafluoride) plus metallic uranium. The refinery, of course, processes the company's own yellowcake but as it is one of only five refineries in the western world, most of its work consists of custom refining for a large variety of customers. In addition to the mining and the refining operations, there have been three other divisions involved, and these are, respectively, Aviation, R. & D., and Exploration, in addition to the financial, corporate, administrative and support activities. MATERIAL AND METHODS The human study population (Abbatt, J.D. et al., 1980) consists of all Eldorado employees who have ever worked for E.N.L. and for whom records are available. The total nominal roll to December 31, 1980 is approximately 21,000 and consists of employees of the Mining, Refining, R. & D., Aviation and Exploration Divisions, as well as a relatively small number of other employees (Head Office, etc.). The basic epidemiologic design, as has been mentioned, is for a retrospective cohort study merging into a prospective cohort study, and depending very heavily upon automated record linkage and file matching. The original design called for an initial assembly of the bulk of the nominal roll, prior to the first of two matches with the National Mortality File. The first of these two matches is now complete and the second is to be separated from it in time by 18 months to two years. The second match will be the definitive match prior to the analysis, the interpretation of the data, and the publication of the results. The period between the two matches was designed to permit completion of the nominal roll, including: - addition of previously missing individuals and groups, elimination of duplicates, and amplification of identifying information, - assembly of work histories and exposure information for each individual, - digestion and application of lessons and modifications resulting from the first match with the National Mortality File at Statistics Canada, - preparation of files for the definitive second match. The analysis of data will be carried out by the National Cancer Institute of Canada Epidemiology Unit based at the University of Toronto. This group, with whom Eldorado Nuclear has a memorandum of understanding, have for a variety of reasons, including their familiarity with record linkage and their expertise, been members of the Project Team since

Jan 1, 1981

By John V. Beall

A completed feasibility study executed by an independent agency can benefit a company in two ways. Inside the organization, it verifies the project staffs ideas and their concept of the facility. Outside the company, it can be utilized to obtain equity partners, debt financing, and other forms of credit. It is advisable to bring in a project execution contractor for the feasibility study. A project execution contractor is able to work with engineers to develop the project concept, process flowsheet, and best utilization of the site. By getting an early start on understanding a company's policies and working methods, a project execution contractor saves the company money since it does not have to go through the educational buildup twice. The contractor is a specialist in putting together a bankable document that can be taken to a financing source. It answers all the agency requirements on the first pass. In addition, the contractor can advise an owner on likely financing sources since he works on the worldwide market every day. A less obvious advantage of including the contractor in the study and predevelopment buildup stages is the importance of coordinating finance and technical input. The financing source influences equipment specifications, procurement, logistics, project schedule, cash flow, and liquidity. There are many surprises in store for any manager of a large international project involving worldwide financing and purchasing. The job does not have to be made more difficult by bringing in a contractor after all predevelopment steps are taken. The contractor can still work if the predevelopment steps have been done, even if he does not agree with them. But early contractor involvement is the preferable solution.

Jan 10, 1980

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By E. D. Attanasi, J. H. DeYoung

Several factors contributed to continued declines in mineral-exploration activity in the US in 1985. Low metal prices and, what appears to be worldwide chronic excess capacity in copper, molybdenum, lead, and uranium, have resulted in mineral-exploration expenditures remaining anemic. Economic recovery could result in a healthier mining industry and more cash flow to fund exploration. This is because general economic activity and US mining industry activity have historically been closely linked. However, as the worldwide economic recovery has expanded, the mining sector has continued its downward slide. New cuts in industry exploration budgets in 1985 shocked those who thought the exploration situation could not become worse. Some personnel and equipment had been redirected from base metals exploration to precious metals in the past few years. Last year, continued reductions in exploration sent many professionals out of the mining industry. Recent staff reductions or consolidations of operations were made by Noranda, Chevron, Molycorp, and other exploration companies. The latest data from the Society of Economic Geologists (SEG) summary of exploration statistics show that professional staff at year end in major US exploration companies (domestic and foreign operations) fell from 2355 in 1981 to 1868 in 1983 and 1277 in 1984. By the end of 1985, two economic trends were established that could improve the future profitability of mining and hence exploration. First, the price of crude oil began a decline. If sharply reduced energy prices increase worldwide economic expansion, the substantial excess capacity in some of the base metals industries could disappear, and prices could improve. Furthermore, if energy price declines reduce mining and processing costs significantly, metals may recapture some lost markets. The decline in oil revenues has already encouraged some oil-producing countries, such as Venezuela, to look toward development of mineral resources to earn foreign exchange for debt repayment. Second, the decline of the dollar by 21% during 1985 could also help US producers meet foreign competition. During 1985, industry restructuring continued as many oil companies sold off mining subsidiaries and minerals properties. Gold, silver in new discoveries Precious metals continued to dominate the announcement of new discoveries and exploration projects in 1985. A review of domestic exploration and development activities reported in several industry journals shows that 60% to 80% of these projects were directed primarily at precious metals, particularly gold. Base metals exploration activities frequently involved polymetallic deposits with gold or silver values. Because much of this exploration was done on identified targets (on-property exploration), the decrease in wildcat or grassroots (off-property) exploration may be more substantial than indicated by reductions in total exploration activity. Significant gold discoveries in 1985 included several in Nevada, among them the Genesis property of Newmont (near the Carlin mine), Goldfields' discovery of the Chimney deposit in Humboldt Co., and Freeport's discovery of two mineralized sites near Jerritt Canyon. Gold exploration continued to be focused in the western US and Alaska, but gold production starts at the Haile mine in South Carolina, and the Ropes mine in Michigan as well as Amselco's feasibility studies on deposits near Ridgeway, SC, are evidence that gold exploration is not limited to the West. The dominance of gold projects in exploration is not limited to the US, as demonstrated by gold dis¬coveries and exploration projects in Australia, Brazil, Canada, the Caribbean region, China, Guinea, Ivory Coast, South Africa, the South Pacific islands, and Thailand. From the standpoint of US metal miners, it is perplexing that worldwide exploration and development is also taking place in copper, zinc, tungsten, and other metals with depressed prices. During 1985, the US Geological Survey's efforts to map the sea floor of the Exclusive Economic Zone shifted from the Pacific Coast to the deep water areas of the Gulf of Mexico and to areas off the coast of Puerto Rico and the Virgin Islands. An atlas containing sea-floor maps of the west coast area was published as US Geological Survey Miscellaneous Investigations Series Map 1-1792. Results of the 1985 surveys are expected to be published by January 1987. Exploration trends - Statistical evidence Data from the SEG showed continued decline in the US mining industry's exploration expenditures through 1984. The share of US companies' domestic exploration expenditures directed toward base and precious metals has increased from 51% to 84% from 1980 to 1983 and to 86% in 1984. US mining companies spent about $0.67 of each exploration dollar in 1984 in the US. However, this represents an increase from earlier years. The 1983 data also show that firms spending more than $5 million on exploration accounted for 77% of exploration expenditures. Since 1981, the Bureau of Land Management (BLM) has been assembling data on claims and an-

Jan 5, 1986

By D. R. East

The concept of sub-aerial tailings deposit.ion using a managed rotational deposition system to form a deposit of partly-saturated tails for North American conditions was introduced by Knight and described by Knight and Haile (1983). The application of the sub-aerial technique, together with continuous removal of all surface waters and underdrainage outflows from the Key Lake uranium mine I s tailing storage facility in Northern Saskatchewan, Canada, has been documented by Knight and Haile (1984). Since then, the concept is being applied in the United States to tailings facilities in California, Nevada, Arizona, Utah, Colorado, Idaho and South Dakota.

Jan 1, 1989

By Johann Knecht

Due to lower specific investment and operating costs the tendency towards large scale equipment will remain. For the design engineers not only the stresses in the mill structure and manufacturing are of importance but also transportation to and erection on site. A scale up of the design of smaller sized units on the pantograph principle may not always give the best approach to the job in this respect. This paper covers recent developments in the design of large size equipment where the huge dimensions call for designs being different to the well known ball and SAG mill concept with cast conical endwalls. The first part describes the features of the biggest ball mill in the world, whereas the second part provides some details of the largest shell supported SAG mills being currently in the manufacturing process.

Jan 1, 1993

By James E. Monsees

Extensive underground excavation will be required for construction of a mined geologic repository for nuclear waste. Hundreds of thousands of feet of drift will be required based on the conceptual layout design for each candidate nuclear waste repository. Comparison of boring and blasting excavation methods are discussed, as are special design and construction requirements (e.g., quality assurance procedures and performance assessment) for the nuclear waste repository. Comparisons are made between boring and blasting construction methods for the repository designs proposed for salt, volcanic tuff, and basalt. Differences in the geologic media and settings of the prospective sites influence the excavation method in terms of drift length, size of opening, drift slope, rock quality, and boreability. Support requirements, ventilation, and the ability of the geologic system to retard radionuclide migration are also directly impacted by the geology and excavation method.

Jan 1, 1987

By A. Covelli, A. B. Cecala

Two recent US Bureau of Mines studies evaluated workers' dust exposures in automated pallet loading processes. The first study involved a Bureau designed dust control system using a push-pull ventilation technique. The unit was shown to reduce workers' dust exposures by 76% during pallet loading at a ground silica operation. A hydraulic lift table was used to automate the bag stacking process. This kept the loading height constant throughout the entire pallet loading cycle. The second study evaluated different commercial, automated-pallet loading systems. These systems automatically stack the bags onto pallets, shrink wrap the pallets, and deliver the pallets to a fork lift pickup location. Results from a ground silica evaluation site indicated respirable dust samples taken were below the Threshold Limit Value (TLV) as established by the Mine Safety and Health Administration (MSHA).

Jan 1, 1992

By A. D. Hammond

"INTRODUCTION Vanadium deposits in Arizona are distributed all across the state, from the rim of the Grand Canyon to the Tombstone mining district in the southeast corner of the state (Figure 1). The combined past production of vanadium from Arizona and New Mexico ranks second nationwide, after deposits in the Colorado Plateau In the northeast corner of the state, in the Carrizo Mountains and Monument Valley of Apache and Navajo Counties, vanadium was produced as a by-product of uranium in deposits of the Salt Wash and Shinarump members of the Morrison and Chinle formations, respectively. The production took place between 1943 and 1970. Another source of vanadium in Arizona occurs in vanadate deposits associated with supergene enrichment of base-metal vein and replacement deposits. The most important vanadate mineral is vanadinite, a chloro-vanadate of lead. Presently, there are no primary mines of vanadium in the United States. In 2012, a small production of vanadium pentaoxide (V2O5) was reported as a by-product of uranium at the White Mesa uranium mine in Utah1. This paper describes vanadate deposits in Arizona with emphasis in three districts, namely, the Mammoth, Globe-Miami and Banner districts.VANADIUM EPIGENETIC DEPOSITS: VANADATES Almost all vanadium epigenetic deposits occur as vanadates in oxidized zones of lead, zinc and copper veins and replacement deposits. Vanadinite, descloizite and mottramite are the most common minerals in vanadate deposits. Descloizite is a vanadate of lead, zinc and copper. Wulfenite, a molybdate of lead is also present. These minerals replace supergene base-metal minerals, form crusts on faces of open cavities, or are inter-grown with residual clays in pockets. The vanadium content in vanadate deposits is believed to have been leached from the country rock by ground-water and transported through porous rocks until precipitating as a relatively insoluble vanadium compound or until the solution evaporated. Precipitation was brought about by local concentrations of cations of divalent lead, zinc or copper. Lead is a constituent part of almost all of vanadate deposits and the vanadium pentaoxide (V2O5) content in vanadate minerals seems to have a direct correlation with the content of lead in the hypogene mineral. Vanadate deposits are restricted almost entirely to the oxidized parts of vein or replacement deposits. It is rare that oxidized zones extend past 100 ft from the surface. Vanadate deposits are largely restricted to tropical and temperate zones and regions of dry climate. Arizona and New Mexico have the largest concentration of vanadate deposits in North America."

Jan 1, 2015

By YOUNIS S. MUSTAFA, GHORASHI ZAIN, ABDEL-ZAHER M. ABOUZEID, AHMED A. S. SEIFELNASSR

The present paper attempts to characterize the breakage properties of a brittle rock, quartz, at different size fractions when compressed at various loads in a confined piston die.  This is to understand the interaction between the various parameters affecting the breakage behavior of a brittle solid in a confined zone. Application of the results may lead to improving the energy efficiency in the size-reduction units, which use compression as the main stressing force. 

By Wallace W. Roepke, James C. Church

Introduction The history of mining machine development has been and is one of "bigger is better." While this may not always be true, it is currently the only approach open to machine designers without specific in situ cutting force information. The US Bureau of Mines has tried to modify this approach by supporting research, both in the laboratory and in field tests, that demonstrates that bigger is only better if the equipment is used correctly. In-house research has shown conclusively that deeper cutting reduces both dust and energy (Roepke, Lindroth, and Myren, 1976). This approach has been applied to a large Lee-Norse (LN456) continuous mining machine, which confirmed that slow deep cutting is beneficial and does not have a negative effect on production (Black and Rounds, 1977; Black et al., 1978). Specific in situ engineering data needed on coal cutting forces have not, however, been obtained by field tests with the LN456. Although the machine was instrumented to obtain data on one seam, it would be impractical to move the machine from mine to mine. It became apparent that a portable, easy to use device was needed for obtaining coal cutting forces in situ. Such a device could provide the engineering data needed by manufacturers, the site-specific cutting information needed by operators, and a field research tool to establish correlation with laboratory cutting tests. Design and Development According to a set of design guidelines established by the Bureau, the proposed device should be able to measure cutting forces directly with standard coal cutting bits, be transportable by two miners, and be self-contained. These guidelines were given to Ingersoll-Rand Research Inc. (IRRI). The contractor performed a rigorous review of 16 existing in situ portable tester designs, none of which could use a standard coal cutting bit to measure cutting force directly. These included a wide range of devices, all of which are discussed in the final report (Banerjee and Wisner, 1982). A series of design tradeoffs were established to satisfy initial design guidelines. The final deci¬sion was heavily weighted by an industry survey to determine the preferred concept from four man¬ufacturers and four operators. To assure ease of use with maximum information, all respondents wanted a linear cutting device that could work in seams down to 1 m (40 in.). The final design choice was between a linear and a rotary tester. The rotary tester would cut on an arc in the same manner as a rotary drum machine. It had several faults, however, that could not be resolved within the scope of this contract. The worst was related to arc cutting (Roepke, Lindroth, and Myren, 1976). Since any bit cutting on arc enters the coal at zero depth, goes to maximum depth only at the horizontal centerline, and exits at zero, maximum cutting force is obtained only at the instant the bit crosses the horizontal centerline. This centerline peak response would require that many replications be made with an arc-type cutter to get reliable force information. The arc-type tester would require extensive face preparation to establish the cutting path and extensive wasted clearing cuts to advance the device for additional layers of cuts. The linear tester could be mounted directly on any face or rib with only minor preparation. By its nature, a linear cut at a constant depth provides multiple peak force data over the length of the cut, thus reducing the required number of replications. The final review of these two major design concepts plus indus-

Jan 9, 1983

By H. Yoon

Several processes involving injection of sorbent and humidification water downstream of the air preheater in a coal-fired boiler unit, are being developed as low capital cost retrofit S02 control options. Extensive laboratory work, pilot plant programs and larger scale programs have developed performance data and design information. Many of these programs were supported by the U. S. Department of Energy (DOE) as "proofs-of-concept" of three different processes proposed by Dravo, Bechtel and General Electric. Based on these project results, DOE formulated a comprehensive in-duct sorbent injection development program to fully commercialize the technology by 1992. Also, EPRI will conduct a 4 MWe pilot program to develop its HYPAS process. The Consol Coolside process is scheduled for utility demonstration in 1989 on a 104 MWe unit at the Ohio Edison Edgewater Station under partial sponsorship of the DOE Clean Coal Technology Program.

Jan 1, 1989