Search Documents

By S. K. Das Gupta

The rock laterite was first discovered and described in the State of Kerala, India in 1800 A.D. by Francis Buchanan. It had been used here, and elsewhere in India, for many centuries as a building stone, but in Buchanan's time it was not known that some of these laterites were highly aluminous and could be processed to produce alumina. After World War I India started searching for bauxite reserves with a minimum grade of at least 50% A12O3. By 1960, it was estimated that India had a potential reserve of 245 million tonnes of bauxite, about 10% of which was in the "Proved" category. Subsequent geological exploration now reveals that India has an overall resource of more than 2 billion tonnes of aluminium ore, not all of it bauxite, as defined by earlier geologists. In this paper, the geology, resources and distribution of bauxite and aluminium ore throughout India are described. The generalised stratigraphy, typical laterite and bauxite profiles and summary of the resource position are shown in the attached Tables 1 to 8. It is generally agreed that a tropical to sub-tropical climate, intermittent wet and dry season, good permeability of country rock and suitable drainage, as well as physiographic and ground water conditions are important in the development of bauxite.

Jan 1, 1984

By Y. V. Vasylchuk

An algorithm is presented for optimizing the classification of surface mine material subject to excavating constraints. High-resolution, expected-profit models are optimized to classification maps subject to site-specific excavating constraints. This optimization problem defies traditional closed-form analytical solutions. A practical heuristic algorithm quickly determines the optimum final destination for material subject to realistic selectivity constraints. The expected profit could be calculated from an estimated model if the value calculations are all linear; otherwise, simulation could be used. In both cases, a single expected profit for all destinations on a high-resolution grid is the starting point for dig limits optimization. Maximizing expected profit in a risk-neutral manner is correct given the repeated nature of grade-control decisions over relatively short timeframes.

By William G. Freeman

In comparison to many mineral commodities, barite has a low unit value. It is mined and sold in low volumes in high-grade (90-98% BaSO4) forms to basically one industry that uses approximately 75% of the free world production. Based upon the above criteria, all factors must be considered in determining if a barite deposit is economical; such as, the type of deposit, mining and milling methods required, transportation to the markets, tariffs, local political conditions, etc. In other words, barite mines are made--not found. The length of this paper precludes any indepth discussion of geology, mining and metallurgy of barite. Most of this information can be found in data already published, such as D. A. Brobst's bulletin1 on the Barite Resources of the United States.

Jan 1, 1971

By J. H. Gwynne

[ ]

Jan 1, 1962

By David M. Abbott

This paper is a companion to, and amplification of, the ?History? section of the 2014 version of the SME Guide for Reporting Exploration Results, Mineral Resources, and Mineral Reserves (SME Guide). The need for the careful examination and evaluation of mineral deposits has long been recognized. In the book De Re Metallica, Georgius Agricola noted, ?Moreover, a prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him? (1556, p.29). Agricola further stated, ?Now a miner, before he begins to mine the veins, must consider seven things, namely: the situation, the conditions, the water, the roads, the climate, the right of ownership and the neighbors? (1556, p. 30). The elements of Agricola?s seven things, much expanded, are incorporated into the 2014 SME Guide. As reflected in this quotation, veins were the primary concern of mining until 20th century technology permitted bulk mining techniques. The need for standardization of reserve descriptions arose along with the development of western mining in the United States and the concurrent development of mining engineering and mining geology as professions. By the turn of the century, debate about terminology of various classes of reserves was in full swing. Herbert Hoover noted in 1909 (p. 16-17), ?The old terms ?ore in sight? and ?profit in sight? have been of late years subject to much malediction on the part of engineers because these expressions have been so badly abused by the charlatans of mining in attempts to cover the flights of their imaginations. A large part of Volume I of the Institution of Mining and Metallurgy has been devoted to heaping infamy on these terms, yet not only have they preserved their places in professional nomenclature, but nothing has been found to supersede them. ?Some general term is required in daily practice to cover the available field of visible ore, and if the phrase ?ore in sight? be defined, it will be easier to teach the layman its proper use than to abolish it. In fact, substitutes are becoming as badly abused as the originals ever were. All convincing expressions will be misused by somebody.? Hoover (1909) noted that the common terms at the time were: ? Positive ore or ore developed: Ore exposed on four sides in blocks of a prescribed size. ? Ore blocked out: Ore exposed on three sides within a reasonable distance of each other. ? Probable ore or ore developing: Ore exposed on two sides, ? Possible ore or ore expectant: Ore in whole or in part below or beyond the range of vision. Hoover stated that these, and similar terms, overlapped and had the difficulty of failing to account properly for geologic variation in metal distribution beyond the exposed face. Certainly assuming extension of values along a vein is reasonable, but how far? Also, these definitions are for vein deposits, not all types of deposits are in veins. Hoover (1909, p. 19), therefore, defined the following terms. ? Proved ore: Ore where there is practically no risk in failure of continuity. ? Probable ore: Ore where there is some risk, yet warrantable justification for assumption of continuity. ? Prospective ore: Ore that cannot be included in the above classes, nor definitely known or stated in any terms of tonnage.

Feb 1, 2014

By Christian Heinz, Doug Harding

TBMs can last for decades and be rebuilt project after project with proper maintenance. How successful can rebuilt TBMs be? At the DigIndy Tunnel System in Indianapolis, Indiana, USA, a rebuilt TBM was used to great effect. The 6.2 m diameter Main Beam, originally manufactured in 1980, bored 40+ km of tunnels and set three world records in its size class of 6 to 7 m, including a best month of 1,754 m. In this paper, the authors analyze the TBM rebuild, performance and lessons learned to make recommendations for future projects seeking to use rebuilt TBMs over long distances.

Jun 23, 2024

By R. W. Smith, Z. Sadowski

INTRODUCTION Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of contaminant metal ions and other chemicals on the flotation. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances, cations such as Ca2+, Mg2+, Fe2+, and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions. Some adsorption (abstraction) experiments were also performed. Experimental materials and methods The barite used was a high-purity, naturally occur¬ring mineral sample (Kings Creek, SC). The material was ground in a porcelain mill and a fine fraction (mean particle size 11.49 µm) separated out by air elutriation. The mean size was determined by an aqueous sedimentation method using a CAHN electro-balance. In the method, an 0.6-g sample of the barite was dispersed in 450 cm3 of pH 7 water containing 0.01 g of sodium tripolyphosphate. The mean particle size was denoted X0. The stability of the barite suspensions was determined by a comparison of the mean size of the investigated barite suspension aggregations with the mean size of barite powder determined in the presence of sodium tripolyphosphate. The mean sizes (X) of the barite aggregations were determined using the same amount of water and barite sample as in the measurements of dispersed barite particle size but without the presence of polyphosphate. The ratio X/Xo is thus a measure of the stability of a suspension (the greater the ratio, the less stable the suspension). The adsorption (abstraction) experiments were carried out in polyethylene bottles containing 1 g of barite powder in 200 mL of solution. The solids were added to a solution containing a known concentration of metal chloride salts (AlCl3, FeCl2, MgCl2, and CaCl2) . The pH was controlled by both HCl and NaOH addition. The suspensions were agitated in a shaker for three hours. The final ion concentrations in solution were determined by atomic absorption analysis. The electrokinetic measurements were made using a Komline-Sanderson Zeta Reader in a conventional manner. All experiments were carried out in the presence of 1.0x10-3 k.mol/m3 NaClO4. Experimental results Figure 1 shows the zeta potential of barite particles as a function of pH in the presence of iron(II). The

Jan 1, 1988

By P. M. Krishna

An example illustrates the use of ASTM Standard E901-82, Classification System for Uranium Resources. The example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that ,remain in fixing the classification of a given uranium resource include the uncertainty in estimating the quantity of undiscovered resources and resolving the differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1983

By Joseph M. Tarantino, Eric F. Perry, Keith B. C. Brady, Michael W. Smith

The Pennsylvania Department of Environmental Protection in 1998 reviewed its permitting process to determine how effective its program has been in preventing pollution and to identify here it could be improved. Of the 1,699 bituminous mine permits issued from 1987 to 1 996, 50 were identified to have current or past postmining discharges with water quality problems. The remaining 1,649 sites had no known current or past postmining discharges problems. The 50 sites were selected for further review. On closer examination, 33 of these permits no longer had water quality problems or the problem had not actually resulted from the permitted mining activity. Only 17 permits, or one percent of the total permits issued, were found to have caused long-term postmining discharges serious enough to require treatment and prevent bond release. Analysis of these 17 sites using current knowledge of mine drainage prediction, revealed that the most common cause of error was inadequate information in the permit application. Errors in interpretation of the application data and in implementing the permit were less common. A very small percentage of all permits issued resulted in postmining discharges for no clearly identifiable reason. Trends over the 10-year study period indicated a decreasing incidence of permits resulting in postmining discharges. Further, with the exception of the first few years of data, most of the postmining discharges were of mildly acidic or alkaline quality and amenable to passive treatment.

Jan 1, 2000

By Toshio Fujiwara, Sumikichi Ito, Masao Kitamura

The Tennohji-Benten Giant Trunk Sewer Project has been under construction since 1974 in the eastern part of Osaka, the second largest city in Japan. The entire project is divided into 7 blocks, some of which have already been completed. This 8.8-km sewer tunnel, being driven through a densely populated area, was planned to be constructed by the shield tunneling method. This paper described shield tunneling performances and ground behaviors during the construction of Blocks 2 and 3. An earth pressure shield (dia., 6,750 mm) was employed in Block 3 tunneling. The ground was generally soft and the cover over the tunnel varied from 13 m to only 4.5 m, so that a considerable amount of chemicals was injected to stabilize the ground. A hand-digging type shield (dia., 7,250 mm) was used in Block 2 tunneling under compressed air. For 85 m of the total length of 1.6 km, the soil at the face was extremely soft, and therefore, the ground freezing method was additionally employed.

Jan 1, 1981

By Y. M. Jiang

Many underground instabilities, such as excessive shield loading and roof falls, occur at longwall faces causing safety problems and production losses. Such instability problems are directly related to roof conditions which can be categorized using geological information. . However, most geologic information describing anomalies and variations of immediate and main roofs are not available before mining resulting in unexpected problems in a longwall face. It is apparent that the evaluation of these geologic anomalies provides a great benefit for longwall stability. The purpose of this study is to evaluate roof categories associated with geological anomalies employing fuzzy set theory. The evaluation is based on real-time monitoring information, such as shield leg pressure, developing load on shields, intervals of periodic weighting, and the ratio of developing loads during periodic to normal times. This paper introduces the application of fuzzy set theory for characterizing roof conditions and evaluating of roof similarities.

Jan 1, 1995

By R. J. Pruett

Selective flocculation enables the production of high-brightness kaolin products from kaolin ore once considered too poor in quality for beneficiation into paper-coating pigments. Anatase, Ti(1-X)FeXO2, with X = 0 to 0.05, is a common iron-bearing impurity in sedimentary kaolin that can be unresponsive to kaolin beneficiation processes, such as magnetic separation, due to its extremely fine particle size (<0.3 µm), or chemical bleaching, because of its chemical stability. Described here are selective flocculation technologies that separate anatase by flocculating anatase or flocculating kaolinite from dispersed slurries. Applying the advances in the chemical and mechanical dispersion of ultrafine particles and the selective aggregation of kaolinite or anatase particles have resulted in the selective flocculation processes practiced today that have increased process recoveries from those technologies practiced beginning in the 1960s.

Feb 1, 2012

Power plants that utilize conventional wet flue-gas desulfurization methods produce enormous amounts of flue-gas scrubber sludge. A typical 400 MW power station that burns a high sulfur coal produces 170,000 tons of wet flue-gas scrubber sludge per year. This scrubber sludge is currently landfilled at an enormous cost to utility companies. This material could be used as a raw material for industries that use gypsum, such as the wallboard and plaster industries. However, before it can be used as feedstock for these industries, some of the impurities such as unreacted limestone and silicates must be removed from the scrubber sludge. Froth flotation has tremendous potential for separating these impurities from scrubber sludge. In order to select an optimum flotation process, it is necessary to characterize the surface properties of the major components in the scrubber sludge, which consist of calcium sulfite, calcium sulfate, calcium carbonate (limestone), and silica. In this study zeta potential measurements were used to determine the surface charge of the components in scrubber sludge, with the goal of optimizing a froth flotation process to produce a marketable gypsum product for the wallboard and plaster industries.

Jan 1, 1996

By Silas Li, Michael Harris-Gifford, Jason Choi, William H. Hansmire

Twin-bore tunnels with a single track in each tunnel are currently the most common subway tunnel configuration. However, a large diameter single-bore tunnel with two tracks separated by a center wall could replace twin-bore tunnels and introduce potential benefits but require necessary modifications to the subway system. In particular, a nominal 40-foot-diameter single-bore tunnel can be considered in lieu of nominal 20-foot-diameter twin-bore tunnels. This paper discusses the benefits and modifications introduced by replacing twin-bore tunnels with a single-bore tunnel, with respect to various elements of the subway related to the tunnel, stations, track, and tunnel systems.

Dec 1, 2022

By Laurence M. Demers, Douglas C. Kuhn

It has been suggested that radicals on the surface of dust particles are key chemical factors in the pathophysiology which results from the occupational inhalation of coal and silica dust. In addition, oxygenated derivatives of arachidonic acid (eicosanoids) have been implicated as important biochemical mediators of mineral dust-induced lung disease through their role in bronchial and vascular smooth muscle reactivity, inflammation, and fibrosis. Therefore, we assessed eicosanoid production by the rat alveolar macrophage (AM) exposed in vitro to mineral dusts with varying surface chemical characteristics in order to determine if radicals associated with the mineral dub1 could influence the production of pro-inflammatory mediators in the lung environment. Rat AM were exposed to freshly fractured or "stale" bituminous coal dust, as well as untreated silica or silica calcined to 500°C and 1100°C. Prostaglandin E2 (PGE2) and thromboxane B2 (TxB2) levels in incubation medium were determined by specific radioimmunoassay. When AM were exposed to freshly fractured coal dust, PGE2 and TxB2 production were markedly increased. In contrast, exposure of AM to "stale" dust significantly reduced PGE2 and TxB2 production. In vitro exposure of AM to untreated silica resulted in a significant increase in PGE2 and TxB2 production compared to control. However, exposure of AM to silica calcined to 1100°C resulted in eicosanoid levels which were not significantly different from control. These findings suggest that radicals associated with respirable coal and silica particles may play a key role in the ability of mineral dust to activate AM eicosanoid production.

Jan 1, 1991

By R. L. Bonomi

Developing a mining venture in a foreign country, particularly in South Africa, can be a real challenge to those involved in the operation. The mining division of Southland Energy Corp. was asked to offer consultative support to the New Union Gold Mine, located in the Giyani District, Transvaal, Republic of South Africa, to aid in their expansion from an approximately 65 tonne per day exploration- exploitation project into a full scale mining operation of 300 tpd by January, 1987 with further expansion to 600 tpd by mid-year. This paper ad- dresses the development of the expansion plans, which are presently being implemented. History. Located in the Northern Transvaal, Republic of South Africa, the New Union Gold Mine is part of what is known as the Klein Letaba gold fields. Gold prospecting in the Klein Letaba gold field area dates back to the earliest years of European prospecting activities in the Transvaal where, reportedly, gold was discovered as early as 1887 (figure 1). The claims com- prising the present New Union Gold Mine have been explored by a number of individuals and relatively small mining groups since the early 1930&apos;s. The work done by these entities was aimed at recovering as much gold as possible in the quickest and cheapest manner possible and, as a result, the area was not explored in a systematic fashion. The long-term potential of the area, therefore, was not known until very recently.

Jan 1, 1987

By W. J. Maloney, H. E. Tuneblom, A. J. Smith

The development of a large regional water supply in Southern West Virginia faced several hurdles. This paper deals with the design and construction of the intake shaft where a combination of cutting edge mechanical excavation technologies were utilized to produce a world class project.

Jan 1, 1999

By J. Noll

There is a need for direct tailpipe sampling of diesel vehicles in mines in order to determine the effects of an emissions-based maintenance program, evaluate control technologies such as diesel particulate filters and identify the worst diesel particulate matter (DPM) emitters in a fleet of vehicles. therefore, this study examined the performance of three portable instruments: a personal dust monitor (PDM) manufactured by thermo Scientific, a prototype elemental carbon monitor (Airtec) manufactured by FLIr and a prototype Ae91 instrument from Magee Scientific. These instruments were evaluated on the basis of their ability to provide direct reading tailpipe analysis for DPM. It was determined that the average bias of the tailpipe results from the PDM and the Airtec were 3±12% and 4±20%, respectively, when compared to the standard method of determining tailpipe particulate concentrations from a diluted exhaust. It was also determined that the Ae91 instrument correlated with the standard method.

Oct 1, 2013

By William Gleason

"The Colorado School of Mines has used the Edgar Mine in Idaho Springs as an experimental mine to teach students since 1921. Since the school acquired the former gold, silver, lead and zinc mine, countless students have received hands-on engineering lessons on their way to earning mining engineering degrees. On Dec. 14, the House Subcommittee on Energy and Mineral Resources held a historic field hearing about the future of mining education in the United States in a classroom about 300 m (1,000 ft) inside the Edgar Mine. Representatives Doug Lamborn (R-CO), Rob Bishop (R-UT), Cresent Hardy (R-NV) and Ed Perlmutter (D-CO) were on hand for the first ever congressional hearing held in a mine where they heard testimony supporting the Mining School Enhancement Act, which was introduced to Congress by Hardy and Perlmutter on Oct. 9, 2015. The act, which is part of a larger mining development and reclamation reform package, seeks to address the absence of a viable pipeline necessary to replenish current faculty vacancies in United States Mining Schools. “What better place to hold a hearing to discuss the need for future mining engineering experts,” Subcommittee Chair Lamborn said in his opening statement. “It is a need felt by industry, states, the federal government as well as nonprofits.” The Mining School Enhancement Act would redirect millions of dollars in fees that are being collected from active mining operations to fund the research and educational programs at engineering schools with mining programs. Those fees now are being used in the form of grants awarded by the Surface Mining Control and Reclamation Act of 1977 (SMRCA)."

Jan 1, 2015

By W. C. Taylor

The present fuel situation indicates that, at least for the next 20 to 30 years, the burning of coal will be a main source of energy. All coal contains sulfur, which is converted to sulfur dioxide during combustion. The concentration of sulfur dioxide (SO2) in the resulting flue gas, for most coals, would exceed the limits established by the Environmental Protection Agency (EPA). Therefore, the sulfur must either be removed from the coal prior to its burning, or be collected from the stack gas before it reaches the atmosphere. There is currently a large amount of research devoted to methods of removing the sulfur from the coal before burning, or during combustion in fluidized beds with materials which trap the sulfur in the solid residue. The commercialization of these processes, however, is not expected in the near future. Flue gas desulfurization appears to be the best near term prospect of fulfilling current air quality control regulations. The lime/limestone wet-scrubbing methods are the most advanced flue gas desulfurization processes and will account for the majority of sulfur removal systems in electric power generation. There are currently at least 23 full-scale systems existing or under construction and 17 of these will use the lime or limestone wet-scrubbing process. (1)

Jan 1, 1974