Search Documents

By Christopher J. Bise

INTRODUCTION The principal means for transporting men, supplies, and mined material in an underground or surface mine are rail systems, conveyor belt systems, or a combination of the two. Typically, large underground mines use rail haulage from the mining sections to the hoist, with conveyor belts being used within the sections. Small mines use conveyor belts in the mains and sub- mains as well as in the panels. The size and layout of surface mines also contribute to variations in the way these haulage systems are applied. The following sections address the typical problems confronting mining engineers in designing these haul- age systems. For rail, these include rail selection and turnout design, locomotive tractive-effort calculation, and motor sizing. Belt haulage calculations include belt width and speed specifications, tension and take- up requirements, idler spacings, and motor sizing. TRACK LAYOUTS Introduction The adequacy of mine track layouts is dependent upon such factors as rail weight (Table l), suitable ties, a well-drained roadbed, and properly designed curves, grades, and track alignment. As long as the installation conforms to the manufacturer's recommendations, good service can be expected from the rail system. Typically, mining-engineering calculations for rack layouts have dealt almost exclusively with the design of turnouts. As such, the following section provides the necessary information for computing the theoretically correct dimensions of turnouts. Turnout Design Fig. 1 shows a typical turnout with an identification of the component parts. Fig. 2 identifies the variables that are used to determine the turnout dimensions. The formulas that concern the mining engineer are those listed: [ ]

Jan 1, 1986

A computer simulation of the automatic control of continuous mining machines has been prepared, similar to previous simulations of longwall mining systems and coal thickness sensors. The simulation allows for programmed variation of the horizon detection method, the azimuthal guidance system, the type and configuration of the miner, varying hardness in the unmined face material (leading to varying error in the machine heading), and the miner's cutting cycle. It simulates control of the miner in three axes. Use of the simulator makes it possible to anticipate problems arising from the complex character of underground mining, which include unpredictable multi-pass coupling and unpredictable variation in geological conditions.

Jan 1, 1993

By Remo Grandori, Manfred Jaeger, Fabrizio Antonini, Luis Vigl

The EVINOS-MORNOS tunnel project with its 30 km of length is one of the longest hydraulic tunnel in the world realised with TBM method. The adverse geological conditions, the high cover and the short construction schedule were a great challenge for the successful construction of this tunnel. The paper will describe: the criteria adopted for the tunnel design, the selection of the construction methods and equipment, the productions of the 4 TBMs adopted and the comparison of the behaviour of the different type of TBMs in the various rock conditions, including special conditions, the characteristics of the adopted in situ and precast linings, a comparison between the foreseen and actual construction schedules, the contractual implications of realising a tunnel in such a severe and complex conditions.

Jan 1, 1995

By Chester M. F. Peters

The opportunity to make a close study of the available geologic data existing along the line of the California Aqueduct crossing of the Garlock fault in the Tehachapi Mountains was brought about first by my involvement in the prebid examinations, and later with contractors' claim cases. The California Aqueduct crosses through the western end of the Tehachapi Mountains and cuts across the Garlock fault zone at a location about 9 miles east from its junction with the San Andreas fault zone. This is about 65 miles northwest of Los Angeles and 38 miles southeast of Bakersfield (Fig. 1) (1). This map was published after the tunnels were started and shows the corrected geology. At the crossing the fault has north and south branches which extend northeastward for about 22 miles before converging. In the vicinity immediately east of the tunnel line the north branch of the fault starts to converge toward the west. After crossing the line it passes under the upper plate of the apparent easterly extension of the Pastoria thrust fault, so the actual junction with the south branch is obscured. The aqueduct design called for the expected active slip zone of the north Garlock fault branch to be crossed by the 2,800 foot long Pastoria siphon, which connects with the north portal of Tehachapi Tunnel No. 3. The tunnel would extend through the western end of Genghus Ridge which lies between the north branch and the main south Garlock fault zone in Beartrap Canyon. Here again the

Jan 1, 1997

By Ravi Ray, Kostas Kaklis, Zach Agioutantis

"Modern underground mining is becoming more complex and geotechnically challenging. The engineer uses numerical, analytical, and data-driven methods (empirical and/or experimental) or their combination to overcome these challenges. Each method has its advantages and disadvantages. Nevertheless, given the amount of innovation and experience involved in developing each of these techniques, it will be prudent to use all their benefits rather than favoring one technique over the other. Pillars are the most important support element in an underground mine. A holistic geo-mechanical solution needs to be determined to design mine pillars using a proper sequence and exact mix of the three methods. A combination of these methods, in sync, can encompass the several advantages of the three methods while eliminating their disadvantages. This paper presents a conceptual three-tier solution to the pillar design problem, to improve its design pedigree, using a proper combination of numerical, analytical, and data-driven methods. At the focus of this proposed method lies the Ground Reaction Curve (GRC) concept.INTRODUCTIONAlthough the stability analysis of underground excavations is a challenging problem, its understanding has improved tremendously over recent years through the use of improved tools and techniques. The trial and error method was replaced with more scientific methods like the empirical and analytical methods that are still in use today. Empirical methods were developed based on large data sets obtained from experiments and observations (e.g., coal pillar strength equations). Analytical methods were developed based on mechanical understanding of stability (e.g., safety factor for vertical pillar loading, Convergence Confinement Method). Improvement in computing power and numerical techniques led to the development of several numerical methods (e.g., finite difference, finite element) suitable for geo-mechanical analysis.Each of these methods have certain advantages and limitations. Nevertheless, the user is often puzzled over the proper method selection and over the proper sequence of using them. This exercise becomes more challenging when different methods are combined, where, for example, one has to estimate the pillar strength based on empirical equations (e.g., Mark-Bieniawski coal pillar strength equation), determine the factor of safety based on an analytical approach (e.g., tributary area load divided by pillar strength), and analyze pillar-strata interactions using numerical analysis (see Esterhuizen, Mark, and Murphy, 2010b).Challenges increase when current pillar design methods are designed as passive structures to balance the fixed dead weight of the overburden. This classic suspension design approach does not recognize the self-stabilizing capacity of the overburden (Frith and Reed, 2018). A practical solution to address these issues is the use of numerical analysis. However, one should always keep in mind that the numerical modelling approach may have certain practical limitations."

Jan 1, 2019

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012

By Rolland R. Mates

This paper describes the use of post- tensioned rock anchors to reduce the risk of future damage to a residential structure as a result of coal mine subsidence. The project described in this paper was performed by the Office of Surface Mining Reclamation and Enforcement (OSMRE) of the U. S. Department of the Interior. The OSMRE was created to administer Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977. The responsibilities of OSMRE include "reclamation and restoration of land and water resources, adversely affected by past coal mining including prevention, abatement, control of coal mine subsidence. ?('l) Consequently, OSMRE has been addressing mine subsidence problems since its initial subsidence stabilization project in 1979. Stabilization activities have primarily consisted of supporting the overburden material by injecting materials through drilled bore holes into the underground mine voids. Injection of various materials into mine voids, including fly ash mixtures, coal refuse, cement grout, and gravel has proven to be a successful method of reducing mine subsidence-related surface movements, and has been extensively utilized in mitigating mine subsidence problems. However, the cost of drilling for injection can be extremely high in areas where the depth to the coal seam is great.

Jan 1, 1986

By A. E. Sears

The intent of geomorphic landform design is to mimic the function of the natural landscape. In a surface mine reclamation application, geomorphic landform design has the potential to mitigate stream loss. This research quantified features of reference landforms and performed computer modeling of a conceptual valley-fill design using geomorphic landform principles. A design was created using published design parameters with a software design tool (Carlson Natural Regrade with GeoFluv). Three additional designs, incorporating field-obtained regional geomorphic landform parameters, were completed and resulted in a geomorphic landform design specific to southern West Virginia. This work illustrates the importance of field determination of the ridge to head-of-channel input and drainage density parameters. Values of ridge to head-of-channel distance measured in this study were consistently an order of magnitude greater than software recommended values (SRV); SRV = 24 m (80 ft) versus field= 220 m (720 ft). Similarly, for the drainage density parameter, the software recommended range is 6 to 9 km-1 (80-120 ft/ac). The field measurements for central Appalachia quantified the drainage density to range from 5 to 5.3 km-1 (67-70 ft/ac). This affects Appalachian valley-fill stream construction by making the stream lengths shorter and the land slopes steeper with straighter headwater channels compared with areas in the southwestern United States. While the application of geomorphic landform design to surface mine sites presents challenges, this work provides support for future applications.

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

Because of its small interburden thickness, concentrated stress distributions, high coal seam metamorphism, and complex geological conditions, mining the five coal seams (Nos. 5, 7, 8, 9 and 12) of Kaiping coalfield is difficult. Kaiping coalfield is located within 80 m in the Kailuan Group. The overburden caving caused by mining the five coals seams was measured using ZTR12 geological penetration radar (GPR) survey combined with borehole observations. The development characteristics of full-cover rock fractures after mining were obtained from the GPR scan, which provides a measurement basis for the control of rock strata in close multiple-seam coal mining. For the first time, it was found that the overburden caving pattern shows a periodic triangular caved characteristic. Furthermore, it is proposed that an upright triangular collapsed rock pile and an inverted triangular area with larger fragments piled up alternately appear in the lower gob. The research results show that the roof structure formed in the gob area can support the key overlying strata, which is beneficial to ensure the integrity and stability of the upper coal seams in multiple-seam mining of close-coal seams.

Jan 7, 2020

By Adam H. Zimmerman

Introduction Noranda, like similar businesses, is suffering the pain of previously unheard of currency relationships, a cost structure built in better days, and conditions of gross oversupply possible in almost any commodity. Indeed, it does seem like the worst of all possible worlds is out there before us. To understand a Canadian natural resource company, you must know how the country is organized. So far as natural resources are concerned, Canada is not Canada. Canada is 10 provinces and each own the resources situated therein. Thus, the conditions of extraction, exploitation, and operation are all set by the province, while the conditions of trade and currency are set by the Federal government. This means that what may be the rule in Newfoundland may not be the rule in Manitoba or British Columbia. The second thing is that the Canadian currency has been a satellite of the US dollar for a long time. This means that we hold the unenviable and unjustified position of being the country with the second strongest currency in the world. What this has meant to us is what it has meant to an American operator. Since 1980, a pound of copper fetches 214% more for a Chilean than it does for us and a pound of zinc 115% more for a Belgian. From an American point of view, Canada is favored because its dollar is valued at 25% to 30% less than the U.S. However, because of industrial indiscretions in years past, Canada has a locked in labor cost disadvantage that is very hard to cope with. Canada has a unique situation with its labor unions. Many of the unions are, or have been, internationals and therefore gained undue strength in early days. Canada has a third political party of socialist persuasion. It is entirely funded by dues from laor union members. Thus, we have a politicized workforce. And finally, we have a public service that has the right to strike. This had made the public service unions by far the strongest now in Canada. What this means to the mining industry is that there is somebody out there blazing the trail. The unrelenting power of these public service unions probably creates a climate more conducive to excessive wage settlements in industry than would otherwise be the case. Study, Work, and Pray So what do we do when times get tough? In simple terms, we study a lot, we work harder, and we pray a great deal. We study a lot in terms of learning hitherto unknown strengths and weaknesses of our products, processes, and operations. We work hard in the sense that we do everything possible to improve our productivity. And we pray a lot because, so far, anything else we have done has not been enough. Some years ago, Noranda recognized that its principal base and precious metal operations were diminishing. To provide for the future, we should branch out into other resource type operations. These might be countercyclical and also perhaps a little more permanent. For this reason, Noranda entered the potash, aluminum, and forest products businesses. This, of course, was a 'brilliant' strategy that was much applauded in its early days. We built an excellent potash mine, the smallest inte-

Jan 6, 1985

Microorganisms are finding more use in the mineral industry, with extensive research efforts being reported in 1991. Most of these research efforts were presented in two major meetings, the SME Annual Meeting in Denver (February, 1991) and the Engineering Foundation Conference about Mineral Bioprocessing in Santa Barbara (June 1991). In addition, several articles were published in the IMM Transactions, Minerals and Metallurgical Processing and Water, Air. and Solid Pollution Journal. The literature can be categorized as: • Review articles presenting an overview of the activities in the use of biotechnology in mineral processing. • Research efforts into genetic manipulation of microorganisms to perform a specified job. • Studies in bioleaching of metals from different types of ores. • Biotreatment of wastes from the mineral industry including acidic mine waters, uranium tailings, cyanide destruction, etc. • Investigations into the role of microorganisms in the energy materials, such as oil, coal, tar sands, oil shales, etc. Smith (Mineral Bioprocessing Conference) presented a review of research efforts as well as practical applications of biotechnology in the mineral industry. In another article, Smith et al. (Minerals Engineering) emphasized that extensive fundamentals and applied research work should be pursued to explore the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering.

Jan 1, 1992

By B. Yarar

The critical surface tension of wetting (?c) of Cu2S, FeS2, PbS, and MoS2 were determined by plotting flotation recovery versus YLV which was arranged by methanol, and Extra-polating to % R = 0. ?c values ranged from 26 dyne cm-1 for MoS2 to 49 dyne cm-1 for PbS and elemental sulfur gave a value of 31.5 dyne cm-1. Minerals exhibiting natural flotability of different extents, could be separated from their mixtures in the absence of conventional flotation reagents, but controlled ?LV. Correlations between non-stoichiometry and degree of natural hydrophobicity for MOS2 are also reported in this paper.

Jan 1, 1983

By L. P. James, W. W. Atkinson

Utah has produced about one billion troy oz. (31.7M tonnes) of silver, more than any U.S. state except Idaho. Several very high grade ore systems, now closed, occur within large polymetallic limestone-hosted districts related to plutonic complexes. These Utah mines fed several major lead smelters for nearly a century. Interaction of magmatic chloride-rich fluids with carbonate rocks localized significant bonanzas within these districts. A low sulfidation state was produced in the fluids by their passage through limestones. The Bingham porphyry mine has also yielded more byproduct silver than other porphyry copper-gold systems. Away from exposed intrusive rocks, some large silver-only systems occur in Mesozoic sandstone and in caldera-related veins in volcano sedimentary rocks. Thick permeable latest-Proterozoic basement meta quartzite sequences present beneath western Utah may have been important, as perhaps they were in the Coeur d’Alene district of Idaho, in providing chloride and silver-rich ore fluids. However, it is clear that specific Tertiary magmatic events played an essential role in the evolution of the Utah silver-rich metallogenic province. The largest silver districts in the state are genetically related to porphyritic plutonic rocks.

Jan 1, 2000

By D. C. Dahlin, W. K. O’Connor, G. E. Rush, C. A. Summers, S. J. Gerdemann

The Albany Research Center (ARC) conducted studies of mechanical activation by conventional and ultra-fine grinding techniques to enhance olivine reactivity in mineral carbonation reactions. Activated olivine is one of several solid feed materials used at ARC in reactions with carbon dioxide to form carbonate minerals. This paper compares grinding techniques via energy demand data and product characteristics, including particle size distributions, surface areas, full width at half maximum (FWHM) XRD analyses, and particle morphology by SEM analyses. Reactivity was gauged by percent conversion to carbonate in subsequent carbonation tests.

Jan 1, 2004

By Yun-tao Xin, Yu Yi, Kang Yan, Gang Li, Xiao-dong Lv

This study investigated the selective removal of arsenic from high-arsenic dust in alkaline systems and the effects of different leaching conditions. The results indicated that the liquid–solid ratio, NaOH concentration, and sulfur dosage had a significant influence on the process. The leaching efficiency of arsenic reached 99.57%, while that of lead was as low as 0.03% under appropriate conditions. In particular, the addition of sulfur can effectively promote the leaching of arsenic and reduce the dissolution of lead in the solutions. An artificial neural network was used to model the leaching process. It consisted of a back-propagation artificial neural network model with a “6–10–2” structure that could effectively simulate and predict the value with more than 99% accuracy. Based on the difference in weights of the different parameters in the neural network model, the relative importance of the parameters related to arsenic and lead leaching efficiency was obtained, which followed the order of NaOH concentration, liquid–solid ratio, sulfur dosage, temperature, time, and stirring speed.

Jul 29, 2021

By Mary Nelima Ondiaka, Kayode Henry Talabi, Oladunni Oyelola Alabi, Fatai Olufemi Aramide, Francis Gitau

Iron ore is essential in steel making; however, high-grade ores have diminished, making low-grade ores inevitable. These lowgrade iron ores need further beneficiation to upgrade the iron content. Currently, traditional physical and chemical methods are utilized and are not environmentally friendly. Bio-beneficiation techniques have emerged as a sustainable alternative for mineral recovery. This review delves into recent bio-beneficiation advancements for enhanced low-grade iron ore recovery using microbes. Research has revealed that bio-beneficiation methods such as bio-leaching, bio-flotation, and bio-flocculation have proven successful in iron recovery from ores. The bio-beneficiation process occurs in mild conditions using bio-reagents derived from microbes and offers a reduction of chemicals used in processing. Bio-beneficiation of iron ore potentially offers a relatively energy-efficient, cost-effective, and environmentally friendly method of maximum iron ore recovery. However, this review has identified a scaling-up difficulty in which a future approach for industrial-use applications is offered following a thorough sustainability assessment. Bio-beneficiation, using microbial processes, provides a viable avenue for maximizing iron ore recovery while tackling the constraints of dwindling high-grade iron ore resources and environmental sustainability.

Mar 16, 2024

By V. Rajagopal

Corrosion and abrasion properties of a series of chromium-containing cast iron balls with Cr contents ranging from 0 to 29% was evaluated and compared with austenitic stainless steel and mild steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite with either 5% pyrrhotite or 5% chalcopyrite under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynamic polarization curves under abrasion. An offset in their electrochemical activities was observed somewhere between 16 and 26% Cr. In fact, 26 and 29% Cr cast irons showed an excellent corrosion resistance approaching that of austenitic stainless steel. Flotation recoveries were estimated on a 95% quartzite + 5% pyrrhotite sample ground with various cast iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with corrosive wear obtained from marked ball wear test and with flotation results.

Jan 1, 1991

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001

By Todd Clarke, Ralf Winterberg

For more than a decade the tunneling industry has explored the potential and benefits of macro synthetic fiber (MSF) reinforced concrete solutions for precast tunnel segments. Parallel to industry investigations, academic research is being undertaken to better understand this material when subjected to the typical loads expected during mechanized tunneling. This paper investigates the performance of MSF reinforced precast concrete tunnel segments by means of an experimental program comprising testing of full-scale tunnel segments. The presentation of the satisfactory results of the experimental testing regime will be complemented by a brief case history from a successfully executed project—an America’s First.

Jun 13, 2021