Search Documents

By Ron J. Elliott, David G. Otto

This project involved deep blast densification of recent volcanic avalanche debris deposits consisting of a 43 meter thickness of loose clean to slightly silty sand, gravel, cobbles and boulders deposited as a result of the 1980 eruption of Mt. St. Helens, Washington, U.S.A. This project was carried out to enhance the resistance to liquefaction or dynamic settlement of soil deposits under the bridge abutments for construction of the 59.4 meter long South Coldwater Creek Bridge. As this bridge is located close to the Mt. St. Helens fault, it will in all likelihood be subject to earthquakes in the order of 6.5 with expected accelerations of 0.55g. Without soil densification, the bridge would suffer severe structural damage in the event of a significant earthquake.

Jan 1, 1994

By Winston Wilches B., Scott Scovira

This paper discusses recent changes to the emulsion blend blasting agent used at the Drummond Pribbenow Mine in Colombia, one of the world’s largest open pit coal mines, and the resulting improvements in rock breakage and excavator productivity. Based on field evaluations, the use of High Density Ammonium Nitrate (HDAN) can be effectively implemented in an emulsion blend blasting agent, yielding excellent results in terms of energy release, shelf life and velocity of detonation (VOD). Field evaluations showed that formulations using HDAN exceed the performance of the actual 50%/50% emulsion/ANFO blend using Porous Prill Ammonium Nitrate (PPAN). PPAN is conventionally used for emulsion blend manufacturing, with physical characteristics to facilitate sensitivity during the detonation process.

Jan 1, 2014

Several surface coal mining operations in North America are attempting to adapt microprocessor-based monitoring equipment as well as programmable logic controllers onto rotary blasthole drills, towards improving overall drill and blast productivity. These Monitoring While Drilling (MUD) systems permit the recording and processing of important drilling parameters such as rotary speed and torque, instantaneous penetration rate and weight on the bit, and enable the operator ultimately to optimize drill and bit performance. MWD systems on production drills in surface coal mines offer the potential to define mine bench geology in detail and in advance of explosives loading. Recent advance s in explosives and initiation technology will require such a detailed knowledge of ground conditions in order to be fully exploited. Additionally, the logic developed from drill monitoring technology will eventually enable full drill automation through feedback and control, once a more complete understanding of the influences of rock mass characteristics on machine performance is achieved.

Jan 1, 1988

By Andrew F. McKown

This paper will discuss the mechanisms of potential damage from close-in construction blasting, concentrating on two mechanisms: elastic ground vibrations and non-elastic (permanent) ground deformations. The latter will be shown to be the most dangerous for close-in blasting. With respect to elastic ground vibrations, discussion will center on the differences in vibration frequencies and impacts between typical close-in construction blasting and typical mine and quarry blasts, and how using vibration criteria derived for residential structures near mines can lead to very conservative criteria for close-in construction blasting. The effects of high frequency vibrations seen in close-in blasting will be commented on. Factors affecting the magnitude of ground motions will be discussed. Simple, practical techniques will be presented to minimize the potential for damage from close-in blasting, by minimizing the potential for rock block movement or ground heave. Case histories will be presented to illustrate some of the techniques discussed, and give examples of successful close-in blasting projects.

Jan 1, 1991

By Katherine L. Heineken, Timothy J. Tope, Kim David Murphy

One method for small arms disposal is the use of a deactivation furnace or explosive waste incinerator. There are numerous hurdles a facility typically encounters to get the furnace or incinerator fully operational and permitted. For example, one Department of Defense installation was in the permitting process 7 years, which included numerous facility upgrades and modifications. This paper will discuss the technical approach for proactively addressing permitting issues and requirements and will identify potential pitfalls to avoid as well as ways to reduce costs. For example, when determining the waste profile, the facility should forecast its treatment needs (taking into account the net explosive weight limits of the furnace/incinerator) and then classify the wastes into "chemical families" based on the type and composition of the wastes. One waste from each family should then be selected for potential inclusion in the trial burn. Modeling the waste disposal can help to narrow down the number of wastes requiring characterization during a trial burn, as well as the number of analyses.

Jan 1, 1997

By Thomas E. Ricketts

An important part of underground mine planning and operations involves the reclamation of working areas after blasting before the mining cycle can continue. This is especially true for mining that must use large blasting operations in the vicinity of extensive underground workings. In an effort to develop a rational procedure for estimating mine damage produced by blasting, underground rock fall has been assessed for a large-scale blasting operation in oil shale. The amount of mine damage has been quantified in terms of manshifts of effort required to reclaim underground working areas after blasting. This has been further broken down into the three main phases of reclamation, i.e., scaling and excavation, rockbolting, and miscellaneous repairs on ventilation, utilities, etc. Different types of openings have also been assessed including level tunnels, incline drifts and rooms. The effect of repeated blasting on mine damage has also been documented with initial blasts producing more damage than subsequent blasts.

Jan 1, 1988

By Tom Short, Paul Kunze

In this paper, the authors describe major changes in drilling and blasting methods instituted at the Zortman And Landusky Mining Company Properties to maintain the viability of these north central Montana surface mines in the present period of depressed precious metal prices. The authors explain how improved drilling procedures minimized problems due to uneven benches and floors. They also describe changes in explosives loading and delay blasting techniques which improved fragmentation, thus increasing metal recovery from heap leaching. Quantities were increased substantially and a new bulk explosives loading system was placed in service with a special down-the-hole bulk loading truck and storage facilities for bulk ANFO and bulk emulsion. At the same time, drill patterns were expanded by nearly 40%. The authors also describe a new technique of using explosives to selectively cast waste and ore in different directions so as to reduce the cost of separating the ore.

Jan 1, 1986

By Robert Martin, Brian W. Stump

As part of a series of seismic experiments designed to improve the understanding of the impact of mining blasts on verifying a Comprehensive Test Ban Treaty, a sixteen station network of three-component seismic sensors were deployed around a large cast shot in the Black Thunder Mine. The seismic stations were placed, where possible, at a range of 2.5 kilometers with a constant inter-station spacing of 22.5 degrees. All of the data were recorded with the seismometers oriented such that the radial component pointed to the middle point of the approximately 2 kilometer long shot. High quality data were recorded at each station. Data were scaled to a range of 2.5 kilometers and the sum of the absolute value of the vertical, radial, and transverse channels computed. These observations were used to construct radiation patterns of the seismic energy propagating from the cast shot. It is obvious that cast shots do not radiate seismic energy isotropically. Most of the vertical motion occurs behind the highwall while radial and transverse components of motion are enhanced in directions parallel to the highwall.

Jan 1, 1997

By John Kemeny

There are many methods used to predict blast fragmentation, including empirical and numerical models, field trials, and experience from ongoing blasting. All of these methods require an accurate measurement or prediction of the rock mass properties. These properties include the characteristics of the rock fractures, including fracture density, friction angle, orientation, length, roughness, fill, etc. They also include the hardness of the intact rock, water content, and other parameters. This paper describes three new technologies that can be used to automatically or semi-automatically obtain rock mass properties: digital image processing, 3D laserscanners, and drill monitoring systems. Each of these technologies is described, including the current state of the art, current limitations, and their future potential. Each of these three technologies has advantages and disadvantages. These new technologies, however, have the potential for providing accurate rock mass information in an automated and real time fashion. This information can then form the basis for a new generation of real-time, database driven blast fragmentation models.

Jan 1, 2004

By Leslie Taylor, W. L. Fourney, Uli Leiste

Over the past few years, our laboratory has been investigating the loading on vehicles due to the detonation of buried explosives. We have been using target plates to represent the bottom of the vehicles that were being subject to the forces from the detonating explosives. Parameters shown to be important in the blast loading were type of soil, stand off distance (distance from the surface of the soil to the bottom of the target plate), and depth of burial (distance of the charge center of gravity to the sand surface). We conducted over the first year of our work a large number of tests which looked at the impulse being applied to the plates as a function of depth of burial, stand off distance, and type of soil. Of the three parameters we found stand off distance to be most important, depth of burial to be the next most important parameter, with type of soil least important. We also found that impulse could be scaled with explosive size quite accurately and that results (for impulse) were quite repeatable from one test to the next.

Jan 1, 2008

By Robert A. Cortese, Lon D. Santis

This paper describes a method of measuring continuous detonation rates using standard electronic parts, coaxial cable, and a data recorder such as an oscilloscope. Three six-volt lantern batteries or a DC supply power the electronics that cost less than $100. Included are means of showing low battery power, finding the proper voltage scale on the recorder, and test triggering of the recorder. Modifications of the circuit allow for use in the field to measure charges up to 57 meters and for use in the laboratory to measure short charges. The high resistance (8.709 Ohms/meter) coaxial cable is a mass produced, special order cable available commercially. The driver circuit delivers a constant current to the cable, and as the detonation shorts the cable, a change in circuit voltage occurs. Recording this voltage change over time allows determination of detonation rate resolute to the sampling speed of the recorder. An oscilloscope or personal computer with a data acquisition card can easily record the data for analysis. Detonation rates recorded in the laboratory using the coaxial cable and the Bureau of Mines's traditional probes are presented. The system accurately measured the detonation rates of ANFO confined in steel pipe, detonating cord, and unconfined high explosive.

Jan 1, 1996

By Michael S. Wieland

Toxic fume concentrations from industrial mining explosives depend somewhat upon the type of rock (or other strata) confinement. Though traditional detonation theory disregards this influence, the work principal from thermodynamics reveals it, when the violent interactions that transpire within the rock blast are taken into proper account. Resolution of the work principle technique requires total thermodynamic equilibrium under constraint, so the nonequilibrium dynamics is rendered in that way, using an old trick from theoretical mechanics that revises the representation of forces. The rock pressure reduces to a four-component sum: the rock compressive strength and natural atmospheric pressure, as reckoned quasi-statically, and the gravitational influence and reversed inertial resistance, as reckoned dynamically. Tabulated specie concentrations and graphical trends reveal the dependency upon rock pressure, rock temperature and the fuel-oil percentage in ammonium nitrate mixtures (ANFO), used to illustrate the model. Rigid-wall test chambers have notable ullage (residual space), where rapid expansion influences the reaction quenching, yielding a fume spectrum unlike that for rock confinement; reported rock tests are therefore used for comparisons. For the thermodynamic regime where quenching occurs, seven concentrations are resolved, including carbon monoxide (CO) and total nitrogen oxides (NOX). Their trends yield inferences regarding the way unwanted charge desensitization from transitory hole-to-hole wave impact in conjunction with reduced rock pressure can yield nasty toxic fumes, the dark rusty cloud phenomenon!

Jan 1, 2005

By Josephine Bones, Robb Larson, Daniel Miler

Avalanches are commonly mitigated through the use of explosives at ski resorts and above transportation corridors. Surprisingly, very little research has been conducted on snowpack response to explosive inputs, and efforts to model this response have been limited. The purpose of this ongoing research project is to ascertain an understanding of the dynamic snowpack response in relation to explosive size and height above the snowpack, coupled with snow conditions, to enhance avalanche control. A system of sensors and computer-controlled data acquisition components has been created to record the movement of snow resulting from the charge detonation. The system records acceleration vertically and radially within the snowpack at two distances from the point of detonation as well as blast air pressure at one location during explosive events. The data at two locations allows inferences to be made about the transmittance and attenuation of shock waves through the snowpack radially as well as vertically. The data shows that raising charges above the surface results in increased snowpack dynamic response when compared to surface detonations. Applying power function regression to accelerations for individual charge elevations, it was determined that both radial and vertical rates of attenuation were not dependant on charge elevation. Additionally, raising the charge also resulted in increased dynamic response at depth within the snowpack

Jan 1, 2012

By Greg Mclellan, Mark Johnson, John Pepper

Several large quarrying projects recently occurred in Miramar, Florida. These were closely monitored by the Seismologist of Record and Broward County in accordance with County and City regulations. In addition to this monitoring, the City of Miramar employed The Pepper Engineering Group, Inc., to provide additional spot check monitoring and to review the records of the other two parties on a routine basis. Broward County ordinances require that the location of each shot and the nearest protected structure be recorded along with seismograph measurement of each shot at the nearest protected structure. The positions of the blasts and nearest protected structures were determined using GPS. The blast vibrations were measured by seismograph. Over 600 shots, which are the subject of this study, were measured both by the County, the Seismologist and, on many occasions, The Pepper Engineering Group. As such, the vibration data was constantly cross-checked for consistency. The blasting contractor also provided blast designs for each shot. In this paper, the measured vibrations are plotted in terms of Resultant Peak Particle Velocity (RPPV) versus Scaled Distance (SD) on logarithmic scales. The data curves are fitted with least squares and upper 95% and 99% prediction limits are provided. Equations are presented to predict the RPPV based on scaled distance and prediction level using power fits. Statistical information concerning the derivation of the various limits is presented. The raw data used to develop this paper, along with other information concerning the shots, will be posted on the Internet for use by other researchers.

Jan 1, 2000

By J R. Brinkmann, S G. Giltner

Nearly all of the South African gold mining industry still uses fuse and igniter-cord initiation systems. Over the past 30 years numerous attempts at developing new initiation systems have not yielded a viable alternative. New initiation systems for narrow stopes are currently being developed by various concerns and the likelihood of these efforts producing feasible alternatives is greatly improved due to the recent advances in electronics technology. The greatest potential benefit of alternative initiation systems is increased production rates through improvements in accuracy and reliability of firing over that of fuse/igniter-cord. Another important feature is the capability of millisecond delay firing as this can lead to reduced stope cleaning times by way of enhanced rock throw and improved fragmentation characteristics.

Jan 1, 1989

By Dworzak, Andrzej Biessikirski, Jozef Pyra

During the detonation process 20-30% of the energy is being consumed only on the quarrying pro-cess. The remaining amount of the energy generates harmful effects such as: shock wave, acoustic wave, fly rocks and ground vibrations. The ground vibrations effect is the most dangerous especially to structures which are situated nearby an open pit mine.

Jan 1, 2015

By J L. Jethwa, A G. Gaithankar

The paper deals with a software method developed to design the optimum blast parameters for tunnels and mine roadways for a given set of geo-mining condition without any major discontinuity. The application of the software is presently limited to 8 D-ahaped excavation where inclined hole cut or four-section parallel cut is used with smooth blasting technique.

Jan 1, 1993

By Gerard O'Brien, Douglas Comstock

"The construction of the Third Harbor Tunnel is the first major portion of the Central ArteryProject. The tunnel is designed to connect South Boston to East Boston to alleviateautomobile congestion through the downtown area. The 4000' long tunnel traversesBoston harbor as a cut and cover tunnel as opposed to a bored tunnel."

Jan 1, 1993

By E E. Cloete, R I. McCrindle

Permitted explosives were previously nitroglycerine based and cap sensitive. Due to safety, health and environmental requirements, water-containing explosives, such as watergels and emulsions, were used instead. However, in order for these explosives to perform at their designed level during blasting, a more powerful stimulus than is delivered by detonators on their own is required.

Jan 1, 1999

By Brian Wingfield, Rick Givens, Greg Williams

Many technological advancements have been made in explosive products and applications over the last 15 years resulting in productivity and cost gains. However, the application of total energy (engine horsepower) in the majority of rotary drilling technology, has remained virtually unchanged over that period. While advancements have been made in components, efficiency, and types of hydraulic systems used on drills, the application of current hydraulic technology to improve drilling productivity has not been interactive with end users.

Jan 1, 1996