Search Documents

By Hugo Meggitt, Damian R. Siebert, Wystan Carswell

Excavation-induced ground movements are a critical component in the design and construction of deep excavations in urban settings due to the potential adverse effects on adjacent structures and infrastructure. Ground movements are influenced by soil stratigraphy, soil properties, adjacent structures, and construction means and methods. The use of empirical relationships, computer models, and reliance on experience with similar excavations in similar soil conditions often provides a basis for predicting excavation-induced ground movements. In this paper, data from 21 deep excavations approximately 20 ft to 75 ft deep supported by concrete diaphragm “slurry” walls in the Greater Boston area are compared to published literature, considering how different foundation systems (e.g. shallow foundations, caissons, and piles) of abutting structures have been affected by adjacent excavations. The influence of construction method (conventional vs. top-down) on adjacent foundation movements indicate that top-down construction typically results in smaller foundation movements. INTRODUCTION Estimation of ground movements due to excavation is a challenging endeavor, even with complex three- dimensional finite element modeling and high-order constitutive models that are increasingly available in modern engineering practice. Aside from the expense of the soil exploration and testing used to inform these higher-order models, the challenges of modeling past stress history, adjacent structures, and the groundwater conditions during excavation require not only large investments of time during design but also validation from past experience (to avoid a “garbage in, garbage out” paradigm). While site conditions such as soil stratigraphy, soil properties, groundwater conditions, and as-built conditions of adjacent structures can be obtained, measured, and estimated, the effects that means and methods of construction have on ground movements are difficult to quantify. During early phase design, assessments of predicted ground movement are unable to account for all aspects of project construction, nor is it cost-efficient to fully design an excavation while project parameters such as site size and excavation depth are under consideration by the design team. While construction is in progress, benchmarking support of excavation performance and associated ground movements in the context of successfully completed projects allows for a more nuanced view of system performance and provides the opportunity for more informed decision-making (if required) as construction proceeds. For these reasons, the use of empirical relationships and the collection of historical support of excavation performance holds high value for the practicing geotechnical engineer at all phases of the project.

Jan 1, 2019

By Jeffrey Goodwin P. E., Melih Demirkan Ph. D. P. E., Kevin Tehansky P. E.

Just an hour drive down MD 301 from National Harbor, construction to replace the Governor Harry W. Nice Memorial/Senator Thomas ‘Mac’ Middleton Bridge (HNB) began in spring of 2020. The Maryland Transportation Authority (MDTA) contracted with Skanska-Corman-McLean (SCM) to deliver a new US 301 bridge spanning 1.9 miles from Maryland to Virginia over the Potomac River aiming to improve capacity, safety, and access of the roadway. The project area presented a geotechnical design challenge due to the installation of new bridge foundations in the problematic soils of the Atlantic Coastal Plain alluvial deposits. With the existing bridge remaining in service during construction, and the site’s logistical constraints placing new pile driving operations near existing abutments and piers, a complex instrumentation and monitoring plan was developed to ensure public safety throughout the project. This paper discusses the geological conditions of the project area, the collaborative approach of various design team members to develop an appropriate monitoring plan utilizing various instrumentation, an understanding of baseline conditional movements of the existing bridge, and impact response of adjacent construction activity to help deliver effective new bridge foundations while protecting the old ones.

Oct 1, 2022

By Meeok Kim, Paul Beljan, Gordon Chen

"Clinton combined sewer overflow storage (CSO) facility project developed by the Department of Water Environment Protection of Onondaga County, New York, is to improve sewer facilities and infrastructure in Syracuse, New York. The below grade facility will provide a storage of untreated stormwater during highflow periods to be treated later, thus reducing CSO discharges to Onondaga Creek.The CSO system consists of three parallel storage tunnels and two end chambers (west and east chambers) as main underground structure. The storage tunnels are about 850 ft. long, 55 ft. wide, 24 ft tall and located 20 ft deep below grade. The chambers, include above access and operation structure, are about 40 to 55 ft. deep and approximately 60 to 100 ft. wide.Kiewit Infrastructure and Weidlinger Associates Inc. developed an alternative approach for the tunnels to meet the facility completion schedule, strict design guide lines and quality control as an environmental and water tight concrete structure for the project. The original design anticipated use of a TBM machine to bore three parallel tunnels between two previously constructed chambers.The alternative design used a three barrel culvert cast-in-place structure in a cut and cover excavation supported by a soil bentonite wall. The SOE along the jet grouted bottom seal provided a ground water cut off as well.The SOE system is specially designed to enhance the quality of culvert CIP structure construction by providing enough space for a full height construction. Also it further reduces the construction time by having the less squarefootage of jet grout installation. The design of tunnel systems is accomplished effectively through the utilization of soil structure interaction using a finite element methodIntroductionTo avoid construction of an additional treatment plant to handle increases in combined sewage flows, the Department of Water Environment Protection of Onondaga opted to construct the Clinton combined sewer overflow storage (CSO) facility.The Clinton CSO facility provides an environmental friendly mitigation method for combined sewer overflows on Onondaga lake which is located in northwest of Syracuse."

Jan 1, 2015

By Robert Thurner, Albin Norrman, Sami U. Raja

The West Link is a double track railway project currently under construction in Gothenburg, Sweden. The project includes the construction of 8 kms of track, 6 kms of which will be in tunnels. Beside several large excavations, three new stations will be built: Centralen, Haga and Korsvägen, all within the city of Gothenburg. The first construction phase of the project began in May 2018, and the finalization of the project is expected in 2026. The project is divided into five sections. Keller is involved in four of these contracts since the design & planning phase in 2018 assisting the special foundation works with various geotechnical techniques including Dry deep soil mixing (DDSM), jet grouting, rock grouting, uplift piles, sheet piling and rock dowels. The core idea behind successful collaboration has been to apply the right product for a location specific challenge which can help optimise costs & time for the project with a minimal environmental impact. Due to the extensive nature of the project, a team of experts from various locations around the world is helping design and execute various foundation technologies and providing solutions to the practical challenges in the project like working close to existing structures, rail lines, river etc.

May 1, 2022

By Mike Muchard

A design phase load test program was performed at the Broadway Viaduct bridge site to evaluate load carrying capacity and constructability of post grouted drilled shafts. The program included construction, instrumentation, post grouting and load testing of three drilled shafts. Two shafts included sleeve port and plate base grouting apparatus and were post grouted. The third shaft was un-grouted and served as a control shaft for comparison of the un-grouted end bearing. The shafts were 5 feet in diameter with the control shaft at 55 feet in length and post grouted shafts at 55 and 66 feet. SPT borings at the centerline of each test shaft defined geotechnical conditions at each shaft. Test shafts were instrumented with strain gages and concrete integrity was evaluated with crosshole sonic logging. Instrumentation and data acquisition was used during the post grouting operation to fully capture the shaft behavior. Finally, Statnamic load testing was performed on all three shafts to their ultimate capacity. The fine to coarse sandy soils in which the shafts were tipped in were well suited to improvement from post grouting. Grout pressures of 660 psi were achieved with 0.08 inch or less of upward shaft movement. Subsequent Statnamic load tests showed 183 to 192 percent greater end bearing in the post grouted shafts as compared to the un-grouted shaft. The overall result showed a potential savings of approximately 9 feet to 35 feet of drilled shaft length in addition to the increased quality assurance from post grouting.

Jan 1, 2009

By James M. Tantalla, Jr. Ellman

"Construction of the powerhouse for the Willow Island Hydroelectric Project, located at the Willow Island Lock and Dam, required a 120-ft deep temporary excavation inside the limits of a cellular cofferdam on the Ohio River side of the excavation and a soil-bentonite seepage cut-off wall on the landward side of the excavation. Stability analyses were performed for critical sections to evaluate the stability of the soil slopes and rock cuts using limit equilibrium, tension crack, and buckling analysis techniques. The stability analyses indicated adequate factors of safety through the landside embankment sections, and for the weighting berm soil slopes in front of the riverside cellular cofferdam. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated marginal factors of safety for the 100-year flood condition. Consequently, the riverside portion of the excavation required enhanced stability measures, namely the installation of long, high-capacity rock anchors. Also, the dewatering system was modified to lower the site piezometric head to near the top of rock to improve the stability of the rock cuts.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. The rock anchors consisted of multiple, seven-wire strands designed to provide the full-required design load at 60% of the strand capacity. Rock anchor loads varied from 1,968 to 2,074 kips. The maximum number of strands per anchor was 59. Bond lengths assumed an allowable bond stress of 100 psi based on the rock bond from pull-out tests.Project DescriptionAmerican Municipal Power, a nonprofit organization that owns and operates electric generation facilities for its member communities, has been in the process of constructing hydroelectric power plants adjacent to existing navigation locks and dams along the Ohio River. The Willow Island Hydroelectric Plant was recently completed on the West Virginia bank of the river adjacent to the US Army Corp of Engineers (USACE) Willow Island Lock and Dam. The plant is on the opposite river bank to the locks, and includes two turbine generating units with FERC rated capacity of 44MW at a 20-foot head differential. The Ruhlin Company of Sharon Center, Ohio was awarded contracts to construct both the cofferdam and the powerhouse. Construction began in mid-2011, and was completed in early 2016."

Jan 1, 2016

By Steven M. Henderson, Zachary D. Jones

The risk of allocation in construction contracts is a primary concern for all parties. For contracts involving subsurface construction the allocation of site condition risk is critical. In the past one hundred years technological advances fundamentally changed how that risk is allocated; yet another shift in this risk allocation may lie just over the horizon due to advances in geotechnical data management. Around the world initiatives are underway to make geotechnical datasets more open and accessible. In the United States some states like Kentucky have already made geotechnical data readily accessible. This proliferation of geotechnical data in the U.S. may impact the allocation of subsurface risk in construction contracts. Many construction contracts contain a differing site condition clause. That clause allows for a modification of the contract price or schedule if the ground conditions encountered by the contractor differ materially from either what was indicated in the contract documents or would be reasonably expected. A contractor, however, is typically not entitled to that modification if the contractor knew or should have known of the adverse conditions encountered. Courts have interpreted the “should have known” language as requiring contractors to make a reasonable site investigation prior to bidding the project. If geotechnical data is available and accessible and reveals the adverse condition the contractor encounters, courts could find that the contractor should have known of the condition and thus will not be entitled to a modification based on the differing site condition clause. Accordingly, the U.S. could be on the threshold of significant shifts in how the risk of differing site conditions is allocated in construction contracts.

Jan 1, 2017

By Frank Rausche, Scott D. Webster, Rozbeh B. Moghaddam

"Pile foundation driveability is a function of several variables such as subsurface characteristics, hammer type, hammer efficiency, pile type, and plugging conditions. One important phenomenon occurring during pile driving, and yet not well documented and published, is the friction fatigue, where a reduction of shaft resistance is observed as the pile is driven to greater embedment. This paper introduces current soil models developed for the assessment of friction fatigue, and further presents a comparison between predicted driveability obtained from Wave Equation Analysis Program (GRLWEAP) and field driving records. From a literature survey, and review of technical articles, a widely-used soil model known as AH-01 has been selected to analyze the friction fatigue concept. Using a WEAP software, two driveability analysis were completed using the standard approach with setup factors, and adapting the AH-01 model into the WEAP input file. Driveability predictions were compared to the driving records corresponding to a 1676-mm x 44- mm open-ended pipe pile with a total and embedment lengths of 180-m and 119-m, respectively. Results from analyses and the comparison presented in this paper provide further information regarding existing methods for the incorporation of the friction fatigue concept to the driveability analyses, and contributes to a better prediction of driveability of open-ended pipe piles. IntroductionDynamic measurements during pile installation provide more dependable information as compared to results obtained from predictive models used for design. Despite uncertainties associated with a specific project site and foundation type, measured data provides a reliable understanding of the soil resistance and its distribution throughout the length of the pile. Back-calculations or back-analyses based on a series of measured data from a pile driving process could help to obtain reliable models to better predict events related to pile installation process in spite of all variability related to fitted models. One of the widely-used analysis regarding pile driving during the design phase is the “driveability analysis” where capacity, blowcounts, maximum stresses in the pile element, and transferred energy from the hammer to the pile element are predicted using mathematical models along with a software. Such analysis requires relevant information regarding soil, pile, and hammer properties combined with a deep understanding of the level of impact each one of these properties could have on the analysis."

Jan 1, 2017

By Satyajit Vaidya, Rudolph Frizzi, Sandy Larimer

"This paper presents a case history in design and construction of a deep foundation system that included high-capacity open-ended driven piles constructed to support a high-rise building in Manhattan, New York. The project site is bordered by existing buildings, active streets, and critical public transportation infrastructure, which were considered in the new building’s deep foundation and seismic design. This paper focuses on driven pile foundation design and installation through relatively loose soil deposits. Unique design aspects included seismic design considerations, and pile splice design for open-ended steel pipe piles subject to significant uplift and lateral loading. Unique construction aspects included quality assurance of open-ended steel pipe pile splices, and uplift and lateral load testing of driven piles installed in close proximity to other foundation elements installed for the project.SITE CONDITIONS AND SUBSURFACE CONDITIONSThe project site is located in Manhattan, New York, and is bordered by existing buildings, active streets, and critical public transportation infrastructure that is located about 60 feet from the site. The existing sidewalk grades around the site are between about el 4 and about el 13; elevations are referenced to the North American Vertical Datum 1988 (NAVD88).Subsurface conditions at the site generally consist of successive strata of historic fill, former river bottom deposits consisting of compressible clayey soils, and medium dense to dense sand, overlying mica schist bedrock. A generalized subsurface profile is shown in Fig. 1. The historic fill stratum is about 10 to 45 feet thick, and generally consists of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick, concrete, and glass fragments. The underlying former river bottom deposit stratum is up to about 15 to 20 feet thick, and generally consists of very soft to very stiff clay and lenses of very loose to loose sand. Medium dense to dense sand was generally observed below the historic fill and former river bottom deposit strata and overlying bedrock. Top of bedrock was generally observed at about 80 to 105 feet (i.e. at about el -75 to el -100), except in the southeastern portion of the site where the top of rock was observed as deep as about 140 feet (i.e., at about el -135). Groundwater levels typically ranged between about el 1.5 and el -0.5."

Jan 1, 2016

By Jim Slatter, Ben Collingwood

"It is well known that the adoption of an appropriate construction methodology is critical to quality outcomes for bored piles (drilled shafts). Many case studies have been published documenting quality issues that have arisen due to a range of causes involving ground conditions, ground support, drilling and cleaning techniques, groundwater, concrete properties and concreting methods, amongst other things. Despite the body of published information, pile defects remain common in practice. The authors share over 40 years’ experience in the Australian piling industry and have participated in many hundreds of projects involving bored piles in design, construction and testing roles. It is the authors’ experience that many defects are caused by conditions or practices that are known to be problematic, but that are often not recognised or addressed at the time of the works. This paper provides an overview of industry practices and key factors relevant to quality outcomes. The authors draw upon their own construction experience, published case studies and guidelines, and observations from independent pile testing activities they have been involved in across the Australian piling industry. The intent of the paper is to provide a consolidated review of typical industry practices and to highlight key areas in which construction quality can be enhanced.INTRODUCTIONThere are many published studies of cases where bored piles have been constructed and found to have concrete defects. The authors have had personal involvement in many cases where the outcomes and learnings are not publically available. The nature and cause of defects is always dependent on site and project specific factors, and therefore methodologies and materials that produce satisfactory outcomes in certain circumstances may be problematic elsewhere. The process of bored pile construction encompasses the following key areas:??excavation and ground support;??pile preparation and cleaning;??pile reinforcement and fitments.??concrete supply and mix performance;??concrete placement methodology;Each of these elements is equally important and can influence construction quality in completed piles. In the authors’ experience, it is often a combination of seemingly minor issues that leads to significant defects in piles. Conversely, attention to detail in all aspects of bored pile construction is required to produce outcomes of a consistently high standard."

Jan 1, 1900

By Patrick Wong

The design of piling platforms is addressed in BRE (2004) for both fine grained and coarse grained subgrades. However, for coarse grained subgrades, piling platform designs can often be overly conservative due to either conservative assumptions on soil friction angle, or concerns over density variations of granular fill, particularly for made-ground. This paper provides guidelines on economic design of piling platforms on coarse grained subgrade by providing recommendations on ground characterization, assessment of soil properties and the use of non-linear stiffness soil behavior. An innovative performance-based design approach is also introduced, utilizing proof rolling with associated testing and interpretation using small strain theory to overcome concerns regarding potential ground variability of made-ground. A case study is presented to demonstrate the successful application of this performance-based approach to avoid having to construct a new piling platform over a 2 ha area. Small strain, non-linear stiffness theory was used to enable a practical proof rolling pressure to be adopted without having to reach the design or ultimate operating pressure. The author considers that the performance-based approach adopted on the case study may be similarly applied to a range of other projects to derive economic solutions.

Nov 1, 2022

By Babak Mamaqani, Pirooz Barar

The Heights project was located at Fashion Valley North, San Diego, CA. The scope of the project was to replace two existing commercial buildings with a large 7-story multi-family residential building. There was an existing 1:1 slope on the north side of the site. A permanent soil nail wall, 1,000 linear ft long, with a maximum height of 100 ft, was needed to replace the 1:1 slope at the north side of the project to accommodate the development. Previously there was a design for the permanent soil nail wall which required up to 115 ft long soil nails with large diameter rebars and 13 in. thick permanent facing. PB&A was engaged by the owner to conduct soil nail design optimization and value engineering to reduce construction costs and improve scheduling. First, the SnailPlus program was used to check the stability under static and seismic conditions and to design soil nail lengths and sizes. Then, soil nail head forces were calculated to design the permanent facing using FHWA recommended procedure. Another challenge of the project was to evaluate the interaction between a future San Diego Gas and Electric (SDG&E) tower and the soil nail wall. Finite element analyses were conducted with the PLAXIS program to ensure the deflection of the future tower would be within the acceptable range. The soil nail design optimization helped the owner to save approximately $800,000 in construction cost and improved construction scheduling.

Sep 8, 2021

By Hayel M. El-Naggar, Mohamed Sobhi, Mamdouh M. Hamza, Marawan M. Shahien

"This paper presents the results of two lateral load tests on large bored piles in soft clay deposit for a major site in northern Egypt. The tests are carried out on 0.8 m diameter piles. One of the tests is carried out on the pile where the clay starts from the ground surface. The other test is carried out on a pile after surface improvement by replacing the top 1.50 m of the clay deposit by compacted granular soil. The results of the tests show the influence of the surface replacement layer on the lateral load versus lateral displacement relationships of the loaded pile. The results of the two tests are used to calibrate a 3D Finite Element Analysis model for the pile. The model is used to investigate the influence of the thickness and lateral extent of the surface replacement layer on the behavior of laterally loaded large bored piles.INTRODUCTIONLateral loads for piles are produced by seismic events, wind, wave action, ship impact, traffic, and land slide forces. The lateral resistance of a pile is controlled by the stiffness and the strength of the material of the pile and the soil surrounding the upper portion of the pile. In most situations, the soil surrounding the upper portion of the pile is too weak to sustain the design lateral loads. Thus there is a need to increase the lateral resistance of the pile or groups of piles. Such an increase may be achieved by either increase number of piles or increase pile diameter. Alternatively, an economic way to increase the lateral resistance is to improve the soil surrounding the upper portion of the pile (Rollins and Brown, 2011; Faro et al., 2015).Ground improvement has the ability to increase the lateral resistance of the pile by increasing the passive resistance of the soil surrounding the upper portion of the pile. The ground improvement techniques have the potential for being more cost-effective and reducing construction time. In spite of this fact, such techniques are rarely implemented in practice. Further, there are relatively few tests or records available in the literature to guide engineers in evaluating the actual effectiveness of this approach. In addition, there is no standard or methodology to aid engineers in designing increase of lateral resistance with surface ground improvement. There are specific improvement methods for each soil type, whether it is loose cohesionless soil or soft cohesive soil and these methods are provided by Michell (1981), Tershai and Juran (2000), ASCE (1997), and Rollins and Brown (2011). Furthermore, there are number of case histories that add a new hole in the sight, such as the cases provided by Brown et al. (1987, 1988), Mokwa and Duncan (2001), Rollins et al. (2005), Rollins and Cole (2006), Cole and Rollins (2006), Rollins, Snyder et al. (2010) , Rollins, Gerber, and Kwon (2010), Rollins and Nasr (2010), and Gerber et al. (2010)."

Jan 1, 2016

By Silas C. Nichols, Jennifer E. Nicks

"Limit states design (LSD), or load and resistance factor design (LRFD), is a method to account for the uncertainty in loads and resistance through a reliability calibration that requires all applicable limit states (strength, service and extreme) to be checked during foundation design. LRFD has been in use internationally for several decades; however it wasn’t until recently that engineers working on highway projects were required to use the method for the design of highway bridges and other appurtenances. Although the bridge community has been using a form of limit states design for structural components since the early 1970s, the design of foundations for bridges, walls and other geotechnical features had long been performed using allowable stress design (ASD), whereby all uncertainty in loads and material resistance is combined in a single factor of safety. While the move to LRFD was viewed as a more rational approach for the design of bridges and structures, the transition to its use for geotechnical engineering has been met by many with confusion and difficulties in application. This article will revisit the history of transition from ASD to LRFD for geotechnical engineering, summarize the status of the transition and issues with its use, and briefly discuss some emerging research opportunities for improving and advancing the design platform.Background and HistoryUntil about a decade ago, foundations and substructures for bridges were traditionally designed using ASD, while the superstructure was designed using load factor design (LFD), a precursor to LRFD that incorporated factored design loads but no risk assessment. This combination led to uncertain and incompatible safety margins in design for the various bridge components. In 1986, the American Association of State Highway Transportation Officials (AASHTO) Subcommittee on Bridges and Structures (SCOBS) concluded that the standard bridge specifications in use at the time for U.S. transportation projects had significant inconsistencies and gaps, wasn’t up to date with emerging technology and that the development of new specifications was warranted. The proposed solution by the subcommittee was to transition to a more coherent method of design where applicable failure and serviceability conditions could be evaluated considering the uncertainties associated with loads and resistance."

Jan 1, 2015

By Filippo Maria Leoni, George Filz, Wesley Schmutzler, Matteo Bertoni

"The US Army Corps of Engineers selected the Deep Mixing Method (DMM) for the required stabilization at the LPV 111 Project (New Orleans, USA). DMM was used for ground improvement/foundation strengthening and consequently to stabilize and support the burden of the new levee. Two different technologies were used: Trevi Turbo Mix (TTM) and Contrivance Innovation Cement Mixing Columns (CI-CMC). LPV 111 is the largest soil mixing project to date in the USA with its more than 18,000 elements installed to a depth of up to 67 feet for a total of 1.7 million cubic yards of treated soil. The preparation and execution of the project presented many challenges from various points of view. The little time available to complete the job led to the simultaneous utilization of eight deep mixing rigs and batch plants which worked 24 hours per day, 5.5 days per week on a stretch of land approximately 5.3 miles long. Given the imposing geographical extent of the project, a four phase laboratory programme and five field validation test programmes, conducted in as many different areas of the project, were completed to design and optimize the grout mixes and the installation parameters. The massive quality control/quality assurance testing programme produced over 500 drilled core holes and over 5,000 tested specimens in order to determine unconfined compressive strength (UCS) and uniformity of the DMM elements. This paper has the purposes of describing the tremendous challenges encountered and providing valuableinformation that may be useful for other future projects, including details not previously published.INTRODUCTIONReach LPV-111 is part of the Lake Pontchartrain and Vicinity Hurricane Protection System designed to protect the city of New Orleans and the surrounding areas from the surge that would accompany a 100 year hurricane event. LPV-111 measures approximately 8.5 km (5.3 miles) long, of which 7.2 (4.5 miles) extend along the north bank of the Gulf Intracoastal Waterway (GIWW) and the remaining 1.3 (0.8 miles) run north and terminates at the CSX Railroad Gate. The Bayou Sauvage National Wildlife Refuge borders the levee on both sides (Fig. 1)."

Jan 1, 2015

By Akhila Manne, Prasad P. V S R

Storage tanks are heavily loaded thin-shelled structures that exert large loads on and require large foundations to support them. They are generally very sensitive to foundation settlements as it may hinder the performance of tanks resulting in significant commercial or social impacts. Selection of their foundation is dependent on availability of suitable ground and limitations imposed by design specifications. Design of the tank foundations is generally based on theoretical methods and validation by representative field tests. This paper reviews settlement criteria for storage tanks as per national and international standards, case studies of large to medium diameter tanks supported on deep foundation i.e., bored cast-in-situ piles and shallow foundations on improved ground and their performance during load tests & hydro-tests is discussed. Paper concludes that storage tanks can also be supported on shallow foundations resting on improved ground reducing the settlement, time and cost significantly depending on the sub-soil.

Nov 1, 2022

By Leo Panian, Ryan Nagle, Priyanshu Singh, Gina Carlson, Wayne Magnusen

"This case study presents the design and construction of an integrated foundation and ground improvement solution utilizing deep soil mixing (DSM) and micropiles. 270 Brannan is a midrise office building in San Francisco that straddles the historic shoreline that was reclaimed in the 19th century. Subsurface conditions include shallow bedrock inland of the historic shoreline, and steeply dipping bedrock overlain by 60 feet of compressible deposits and liquefiable fill on the bay side. Project challenges included mitigating the liquefaction and lateral spreading hazards, addressing settlement concerns in the fill and the bay deposits, developing a cost-effective foundation support solution, assuring satisfactory seismic performance, and addressing construction restrictions with existing adjacent structures.DSM combined with micropiles was identified as the most cost-effective solution for the ground conditions. The DSM panels act both as a liquefaction mitigation mechanism and a foundation support system. Resistance to seismic overturning is provided by uplift-resisting micropiles. The DSM-micropile solution allows the use of efficient conventional spread footing foundations, integrating isolated micropile groups to anchor the shear walls. Successful installation of the system relied on a program of field testing to validate the design and conformance with the design criteria.INTRODUCTIONThe regular grid of surface streets within San Francisco’s South of Market (SOMA) district provides little evidence of the geotechnical complexities that lie below. In the late 1800s, sand dunes, bedrock hills, cliffs, marshes, and mud flats were flattened and filled, concealing their locations and characteristics. The 1906 San Francisco earthquake and fire leveled many buildings in SOMA; new buildings were built after 1906 – often on top of rubble and debris from the structures that came before. Locally, the combination of natural geology and historical interventions can produce complex subsurface conditions that vary dramatically over short distances. This is particularly true at locations where tidal mudflats once met bedrock hills at the shore of San Francisco Bay.This case study describes an integrated foundation and ground improvement system implemented for a multistory “Class A” office building at a complex SOMA urban infill site. The system utilizes cement deep soil mixing (DSM) in combination with spread footings and micropiles to address a range of design and construction issues, including liquefaction and lateral spreading mitigation; consistency of earthquake ground motions; shallow foundation support; seismic uplift resistance; and avoidance of loading adjacent basement walls. The system was implemented by a technically-sophisticated owner through a process that included constructive collaborations between the project geotechnical engineer, structural engineer, general contractor, and specialty foundation and ground improvement contractor(s). The system is designed to cost-effectively provide a high level of seismic performance."

Jan 1, 2017

By Armin W. Stuedlein, Steven R. Saye

The differences between calculated axial pile capacity and the capacity realized during and following installation has long presented a significant concern for foundation engineers and contractors. Such differences have increased in prevalence with the increased use of larger diameter steel pipe piles and the significant increase in design-build contracting. The writers present concepts to close the gap between calculated axial pile capacity and the capacity realized during and following installation of driven pile foundations, including: (1) pile set-up in plastic soils, (2) limitation of re-driving of piles after setup which serves to reduce pile capacity, (3) the use of a vibratory hammer to install piles in cohesive soils disturbs the supporting soils and reduces the pile side resistance capacity significantly, and (4) long pile installation times for open-ended piles can damage the pile side resistance. Examples are presented from practice to illustrate these concepts and to guide pile installation planning to recognize the installation impacts and either consider alternate installation approaches or to properly consider the installation impacts during design.

By Mario Mauro

In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria. For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.

By Jeremiah M. Jezerski, Russell H. Lutch

The Mount Olivet Road Drop Shaft (MOR-DS) support of excavation (SOE) is a circular unreinforced concrete shaft with an inside diameter of a 30.5 ft (9.3 m) and depth of 120.5 ft (36.7 m), constructed using slurry wall methods. The SOE for the adjacent Mount Olivet Road Approach Channel (MOR-AC) and Mount Olivet Road Ventilation Vault (MOR-VV) near surface structures (NSS) consists of lean mix concrete walls and cement-bentonite walls, respectively, both constructed using slurry wall techniques and reinforced with embedded soldier piles. NSS SOE required multiple levels of preloaded internal bracing, with excavation depths of up to 75 ft (22.9 m). The original design construction sequence for the shaft and NSS SOE required that the MOR-DS be constructed in its entirety and backfilled to ground surface prior to excavation of the adjacent NSS SOE. After installation of the drop shaft and NSS SOE an accelerated construction sequence was implemented requiring the analysis of the excavation support systems to determine if the excavations could be open concurrently without adversely impacting the partially constructed permanent MOR-DS structure. The MOR-DS was analyzed using the finite element analysis (FEA) software, MIDAS GTS, to demonstrate that the unbalanced loads applied to the MOR-DS composite structure due to the revised sequence would not exceed the strength and serviceability requirements per ACI-350 or superseded by the more stringent project requirements. The results of the FEA were used to set limits for geotechnical instrumentation consisting of strain gauges located on the brace levels of the NSS SOE. A comparison of the SOE design hand calculations, FEA model results and instrumentation data is presented.

Oct 1, 2022