Search Documents

By Peter J. Nicholson

Recognition of the liquefaction susceptibility of dam embankments has been heightened since the San Fernando Dam near failure incident in 1971. Both the downstream and upstream slopes of dams can be at risk for slope failure that can lead to breaching of the dam during or after a seismic event. Many dams have been remediated by various means such as the installation of stone columns or by excavation and replacement of the liquefaction susceptible material. Recent engineering and technology advances in equipment and materials has shown that construction of shear walls to the appropriate depths and at the right center to center spacing may be an economical alternative to the more traditional methods. Recently, the downstream embankments of at least 4 dams, from South Carolina to California, have been, or in the process of being remediated by the use of shear walls. The method of installation has been either multi-axis Cement Deep Soil Mixing walls or walls constructed by the use of trench excavation under self-hardening slurry. Four case histories of dam remediation are discussed, three by multi-axis paddle auger CDSM equipment one with the use of self hardening slurry trenches.

Jan 1, 2008

By H. S. Radhakrishna

Foundations supporting power transmission and communications towers are subjected to both compression and uplift loads, often of a cyclic nature. Some novel foundations, combining the beneficial features of grouted and helix anchors with that of compression piles and grillages, were developed by Ontario Hydro during the construction of high voltage transmission lines in Ontario, Canada. In addition to meeting the load requirements, the foundations permit easy installation in swampy areas and also minimize impact on environmentally sensitive terrain. This paper describes the features of these composite foundations and outlines the performance criteria used for their design and installation on the basis of load test results.

Jan 1, 2010

By Roberto Nova

The selection of the Osterberg Cell (O-Cell) technology as the standard testing method for deep foundations of the Railways Po Viaduct in Northern Italy offered a relevant number of field measures on large bored pile behaviour in alluvial soils. The assessment of pile response during such ?non standard? testing procedure was performed through the comparison with standard top load tests on companion piles as well as by numerical models of the tests including a simplified pile-soil interaction scheme. As shown in this paper, the O-Cell technology allowed a careful assessment of the non-linear pile behaviour even at quite small loading levels as those required by a posteriori proof tests on production piles. Simple numerical models proved to be very effective in the simulation and the interpretation of pile behaviour during such unconventional testing procedure.

Jan 1, 2008

By Mai Yuanjian

The stabilization effect in large excavation slope with vacuum wellpoints system during construction of a dry dock located in Guangzhou is introduced in this paper. In-situ observations indicate that the effect of wellpoints for decreasing seepage in slope is remarkable even though the muddy sitty clay in it has poor permeability and the slope can remain its stability well. Meanwhile, a non-linear partial defferential equation has been set up to the whole unsteady seepage process as water level in the foundation pit excavated under water goes down to the bottom and so does the seepage in slope due to dewater by vacuum wellpoints system at the same time. And the finite-defference method has been used to solve the equation mentioned above, which differes from conventional wqy where the equation will be linearized firstly. Since the water heads in slope with wellpoints dewatering are more variable, it is necessary to keep non-linear. The calculation results are in good accordance with observation. Vacuum wellpoinnts for slope stabilization in this work is successful.

Jan 1, 1991

By Kimberly Martin

The EFFC/DFI Carbon Calculator provides the deep foundations industry the opportunity to be a leader when it comes to carbon reduction. This tool was created 10 years ago in an extensive effort by the European Federation of Foundation Contractors (EFFC), DFI, member organizations and Carbone 4, a consultant with ex- perience in life cycle assessment. The tool was born out of the fact that governments and clients were asking for embodied carbon information for foundation systems, and that in- dividual companies were building their own calculators to meet these requests. To help all member organ- izations achieve compliance, and to have a sector-specific tool that is certified to the prevailing standards, EFFC and DFI agreed to partner to create the carbon calculator, which is: Excel based and, therefore, easy to learn and use Updated on a regular schedule Certified to ISO 14067, GHG Protocol and PAS 2050 Free and available for anyone to use Even though this tool is free and easy to use, most projects in the industry do not have a carbon calculation performed. The case to use the calculator is more obvious for members in places like Europe where there are stricter reporting standards and government work can be driven by sustainability over cost. In North America this is not the case, yet. Without directives from clients and governments, what can compel the industry to start regularly using this tool and care about the carbon emissions of projects during design and construction?

Nov 1, 2022

By Lawrence Piccagli

This past spring of 2006, BENCOR installed the concrete reinforced diaphragm walls for the COSMOPOLITAN RESORT & CASINO in Las Vegas, Nevada. The project highlights include the excavation of approx. 326.000 square feet of reinforced diaphragm slurry wall with a thickness of 30 inches and a depth of 100 feet using three reverse circulation trench cutters (hydromills) at the same time. The reinforcing steel cages were fabricated on the 8 acre jobsite and approximately 12,000 cubic yards of 4500 psi concrete was placed via tremie. The jobsite logistics of coordinating three trench cutters and three separate desanding/slurry plants as well as the reinforcing steel fabrication and concrete placement all under a very tight schedule was quite challenging. A second main exercise was the execution of a temporary excavation support. As the excavation depths extends between 66 and 72 feet, five to six rows of temporary tieback anchors were required. Anchor lengths range from 43 -83 feet at a maximum design load of 235 kips.

Jan 1, 2007

By V. T. Ganpule

The effect of Sulphate and Chloride is well understood by the engineers. Most of the codes stipulate permissible limits for sulphate and chloride content in groundwater. Relatively few reference are available about the effect of organic acids on pile concrete. While executing a pile foundation work around Bombay, the authors came across the peculiar phenomenon. The routine testing of water has indicated that water is non-aggressive; however, on exposing the piles, the piles were found to be highly detonated. The testing of water on the guidelines followed by engineers associated with flow through pipes revealed that water is corrosive as per the Ryznar index concept. The present papers discussess the significance of Ryznar index in under water concreting.

Jan 1, 1996

By R. Chowdhury

The relevance of reliability studies for deep foundations is considered in this paper with special reference to pile foundations. Attention is drawn to uncertainties related to applied loads, the load-carrying capacity and the safety margin of a pile foundation. The essential steps in a reliability study are outlined. An essential goal of any study is the determination of the Reliability Index or Safety Index under different conditions of loading and operation. Calculations concerning probability of failure or success require an assumption to be made concerning the probability distribution of the safety margin. The significance of this and other assumptions should be clearly understood. Reliability approaches should be used to complement conventional deterministic studies.

Jan 1, 2010

By X. M. Wu

The paper describes four different types of support for deep excavations, which are currently used in China. Local experiences were illustrated by presenting case histories for each type of support. For braced excavation in soft clays in Shanghai, the earth pressure against bracings were found to be in conformity with the trapizoidal estimation given by Terzaghi and Peck (1967). For tie-back support of excavations in Beijing and Shengyang, earth pressures were found to be much less than those predicted by ordinary rules. In the construction of a mining shaft in coarse sand below ground water level, high pressure jet grouting has been successfully used to form a circular impervious lining of the shaft. As an effective anti-slide measure, large diameter reinforced concrete piles constructed by open shaft method have been widely used with success.

Jan 1, 2010

By X. Y. Hou

The design practice of several circular underground projects with large diameter is summarized. By taking the advantages of load-bearing of circular structure, a rational annular tensile bar support system and a new design method are proposed. Calculation for a car park shows that remarkable results are brought in by this design technique.

Jan 1, 2010

By P. M. Deshpande

An interactive short column system is evolved as alternative to deep foundation system in deep layers of marine clay, the interaction of encased stone column and marine clay carry load without causing conventional settlement. This paper presents concept of the system and its field application as foundation of culverts on marine clay layer of 15 to 17 M underlain by residual soil layer of 5 to 6 M, where conventional pile of 23 to 25 M would have been required.

Jan 1, 1996

By Artak D. Mirzoyan

Pile foundations near the edge of a slope are often required to resist lateral loads. This is particularly important for piles at abutments of bridges. However, very few full-scale tests are available that compare the effect on lateral resistance of piles installed in sloping ground to piles installed in horizontal ground. To investigate the effect of a slope on lateral pile resistance, three full-scale lateral load tests were performed on an instrumented steel pipe pile. For the first test, the pile was laterally loaded in horizontal ground; in the second test, the pile was at the crest of a 30º downward slope; and for the third test, the pile was located three pile diameters from the crest of a 30º slope. The soil around the pile consisted of well-graded clean sand (concrete sand) and was compacted to 95% of the modified Proctor maximum unit weight in all three tests. Lab and in-situ direct shear tests indicated that the friction angle of the sand was approximately 39 degrees. The pile was instrumented with strain gauges so that the bending moment versus depth profile could be determined. Pile head load, deflection and rotation were also measured. Based on the load versus deflection curves, the presence of the slope resulted in a decrease in lateral resistance of about 20% for the pile at the crest of the slope and 8% for the pile at 3D from the crest of the slope relative to the pile in horizontal ground. The presence of the slope also resulted in an increase in the maximum moment of 29% and 20% for the piles at the slope crest and at 3 pile diameters from slope crest, respectively. Analyses using LPILE with the measured friction angle significantly underestimated the lateral resistance for the horizontal soil profile. After calibrating the model with the response of the pile in horizontal sand, analyses including the slope still underestimated lateral resistance by about 20%.

Jan 1, 2007

By Wang Huichang

A tentative mathod for predicting load-settlement relationship and bearing capacity of single piles based directly on the results measured by cone penetrometer with local friction sleeve is presented. It is possible that the load-settlement curves can be constructed by means of CPT and the problem of both the bearing capacity and the settlement behaviour of single piles can be considered jointly. The proposed load-transfer functions are continuous, positive monotonic and nonlinear. a concept of weight mean point resistance 2D above and 4D underneath the pile base to determine the unit ultimate base resistance of piles is presented. The predicted results of seven jacked piles in loess are in good agreement with the load test data.

Jan 1, 1991

By M. Y. Xia

In this paper, based on the Theological tests of the interface between clay and concrete, an interface Theological model is proposed and is used in the finite element analysis which takes soil as viscoelastic mass and Theological effect of the interface between diaphram wall and ground into consideration. Its results are compared with those without an interface element, without considering the relative creep displacement. Close attention is paid to the variation of wall with time under the condition of various interface shear stiffness and viscous sliding coefficient, and their effects on the wall bending moment are primarily verified in the paper. The change of wall bending moment with time, trench heave and wall displacement in different excavation depth, bracing position, parameters for soil are also studied.

Jan 1, 2010

By Frank Borda

Two recent projects were completed in Ontario, Canada for major hospital additions that involved excavation support of heritage masonry structures. Conventional continuous caisson wall schemes were replaced, with significant cost savings, by tied back shotcrete systems. Using a combination of conventional design and FLAC analysis, excavation support was designed to permit excavation in competent to weak soils that limited horizontal movements of the existing structures to between 3 and 8 mm. The use of vertical wall elements (micropiles) integral to the shotcrete wall to support both the vertical wall loads and the face of the excavation was deemed to significantly reduce lateral and vertical wall movements. FLAC analysis was used successfully to predict wall movements and optimize design. The shotcrete method proved to be flexible and adaptable to design changes during the project. This permitted convenient accommodation of changes to the building geometry after excavation support had commenced. In addition the method accommodated staged demolition and excavation support of portions of the existing structure at low cost, conveniently and without delays.

Jan 1, 2004

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 1998

By Bernard H. Hertlein

The introduction of LRFD methods for structural design has been a gradual process by AASHTO, ACI, AISC, ASCE, and the FHWA, which has largely been ignored by the deep foundations industry. In 2007, however, the industry has been obliged to embrace LRFD for any deep foundations on projects involving federal funds. The authors are concerned that the risks caused by the need for, and the difficulty of providing, reliable quality assurance, will result in unnecessarily high safety factors that will defeat part of the purpose of LRFD. A primary attraction of LRFD for owners and engineers alike is that it promises more efficient design, and therefore cost reductions. Unfortunately, a key element of LRFD philosophy is often overlooked - that the applied safety factors can be rationally reduced, often allowing less material to be used, thus saving costs, but only if all the risk factors involved are identified and closely controlled. This means that both the quality of the materials and the quality of the construction work must be adequately monitored, and held to an acceptable standard. In the case of deep foundations, the soil in which the foundation is constructed is also a critical component that must be taken into account in the assessment of risk factors.

Jan 1, 2007

By Wolfram Groh

New underground floors comprising the complete footprint area of the building structure, were constructed under an existing building in sand, located in the Verdun district of Beirut / Lebanon. The works for the rehabilitation and extension of the Verdun 528 building were carried out between December 1999 and August 2000. A restriction of differential vertical movement of existing load bearing walls and columns had to be respected throughout the construction phase of the new basements. Support measures for the building were taken based on a underpinning system with Bauer SVV preloaded micropiles. The specialty of this underpinning job was that the building loads at the time of preloading and excavation of new basements was substantially less than at final stage. The design of the preloading system was particularly challenging in view of the transition from temporary to final load transfer under variable load conditions. Load transfer was based on the Bauer SVV micropile head system applied in several technical variants. Monitoring of levels of structural elements performed throughout the construction works confirmed that the differential movements of adjacent load bearing columns and walls were maintained within the specified limits.

Jan 1, 2002

By Tony Suckling

The commercially available finite element program Plaxis has a key benefit over other finite element analysis programs in that it has a relatively simple user interface to input and output data. This benefit though may also be it?s weakness in that anyone, regardless of their grounding in geotechnical engineering, may use the program and produce results for design. It is essential, as for all engineering design, that the models are checked by competent engineers. This paper describes the key recurring problems found by the authors when checking Plaxis models, such as the generation of the initial in-situ ground stresses and the modelling of groundwater. Interestingly, the authors have not encountered similar problems when checking finite element models produced using other programs and conclude that this may be due to the higher calibre of modeller needed to use these other programs. The geotechnical industry is in a situation at the moment where senior managers who may not have been trained in finite element modelling are relying on less experienced staff who have had some training in modelling, either at university or post graduation. The quality of this training is variable and all organisations running easy to use programs need to be aware of the potential risks and dangers. Management procedures and engineering checks that are essential to validate the results of these models are described, assuming that those in charge are not experienced modellers themselves. The model checking process by competent persons is absolutely essential and it is hoped that this paper will help those organisations that do not have such procedures as part of their own internal Quality Assurance or design validation system. The procedures described are valid for all finite element programs.

Jan 1, 2010

By Shamsher Prakash

Estimation of vertical load carrying capacity of a single vertical pile under earthquake loading is an important task of a design engineer. Lateral vibration of vertical pile is highly influenced by the magnitude of vertical load. Several load reversal, during earthquake loading introduce gap between pile soil interface which reduces its load carrying capacity and increases lateral motion. This paper presents a simple time domain numerical scheme to estimate the lateral pile response, considering the loss of contact of pile at pile soil interface, during impact and earthquake loading. The motion of the pile is limited in the vertical plane. Time domain has been discretised into small intervals. The non linearity of soil properties has been taken into account by discretised Winklers model with Wolfes frequency independent mass spring dash pot coefficient for geometric damping. Suitable software has been developed which keeps track of the load reversal point of each elements.

Jan 1, 1996