Search Documents

By Lastram Rolando, Larry J. Hulbert, Louis J. Cabri, J. H. Gille Laflamme, John L. Campbell, Soey H. Sib, Chris G. Ryan

"The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fine-grained minerals which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700/0 of the major Ni carriers and 78% of the major Cu qurier will be liberated at a grind of 80% -U,.7 ,an (-500 mesh) for typical low-grade gabbro (West zone, sample No.1). For typical ""clinopyroxenite"" (West zone, sample No.2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No.3) the liberation would be 71% and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total 24.5% for typical low-grade gabbro (West zone, sample No. I), 15% for typical ""clinopyroxenite"" (West zone, sample No.2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No.3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fine grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as some would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No.2 and No.3 is closely associated with magnetite. Palladium occurs in diverse ways. It occurs in the form of several Pd minerals (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tellurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chalcopyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerals and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate.However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No.2 and No.3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No.3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No.3, in order to improve Pt and Pd recoveries. Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefined Re-Ir-Qs..Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

By F. Goodarzi

"The nature and distribution of the inorganic components and the concentration of certain environmentally sensitive elements, such as, As, Sb, B, Hr, Cd, CI, F, Mo, Pb, S, and Se, or elements detrimental to the utilization by industry such as B, Na, P and S are very important in determining coal quality. The concentration of elements in coal is controlled by the following factors: (1) frequency of occurrence of partings; (2) nature and habit of occurrence of minerals in coal; (3) environment of coal deposition; (4)rank; (5) geological setting; and (6) weathering.Selective mining of coal can reduce the input of undesirable elements such as As and S by eliminating the part of the seam which is enriched in these elements. IntroductionCoal is a sedimentary rock of plant origin and consists of two components: an inorganic component (minerals) which is formed by influx of clastic sediments into the coal-forming environment and also by activities of groundwater, and an organic component (macerals) which is formed from plant debris deposited in the original coal-forming environment. However, coal is a generic term with a broad range of utilization characteristics. A coal that is attractive for use in one market - such as generation of electricity (combustion) - may not necessarily be acceptable for use in another, such as for production of coke (Davis, 1978).The elements in coal are associated with both macerals and minerals. The elements associated with coal macerals, such as C, H and N are termed elements with organic affInities. The concentration of elements with organic affmities (including B, Br, CI, F, I, S, and Mg) often decrease with increasing ash content of coal (Nicholls, 1968; and Finkehnan,1982). FIgure 1 shows such a trend for chlorine. Some of these elements may also be incorporated in coal maceral as very fine mineral grains (Finkelman, 1982). The elements with organic affmities are often volatilized during combustion and carbonization of coal and emitted in the vapour phase. Emission of some of these elements (C, 0, Br, N and S) is of major environmental concern (Lim, 1979)."

Jan 1, 1994

By J. Lu, M. Mohammadi, C. Pelletier, B. Wassink

Chemical reduction of selenate by chromous ions is proposed as a novel method to remove selenate from sulfate-bearing solutions Chromous ions were generated by electrochemical reduction of chromic ions using an electrochemical cell. The investigation was conducted in sulfate medium and under various concentrations of chromous ions (0.0062 to 0.05M), pH 1 to 2.2 and temperature 10 to 60°C. Selenate ions were rapidly reduced by chromous ions to hydrogen selenide. The overall reaction at a chromous/selenate molar ratio of 8 or higher can be expressed by the following reaction. At an initial chromous/selenate molar ratio below 8, the products are hydrogen selenide and elemental selenium. At a lower chromous/selenate molar ratio and pH, more elemental selenium and less hydrogen selenide are produced. The reduction kinetics is controlled by both chromous ion and hydrogen ions concentrations. The reaction rate is first order with respect to selenate, hydrogen ion and chromous ion concentrations. It was found that the selenate reduction rate with chromous is independent of the concentration of sulfate present in the solution. The general rate equation was proposed and the rate constant was calculated as k= 0.38 M-2s-1. An activation energy of 58.7 kJ/mol was obtained in the temperature range from 10 to 50°C. Nearly 100% of selenate can be reduced to H2Se from solution containing 17 ppm selenate in less than 30 minutes at pH 2.2 and 60°C. Various strategies have been tested to remove the produced H2Se from solution. INTRODUCTION Selenium in nature is mostly associated with metal sulfide minerals such as copper, iron, zinc, and lead sulfides (Zingaro & Cooper, 1974). The extraction of metals from ores has the potential for selenium contamination of ground and surface water which can pose an environmental and health concern. Therefore, selenium contamination in the receiving environment is a key issue for many industries (specifically copper industry) and the treatment of wastewater contaminated with selenium is a growing challenge. The effective removal of selenium from contaminated water is very important to support sustainability in the copper industry and the other industries with selenium pollution issues.

Jan 1, 2019

By D. T. Smith, S. J. Strohmayr

Originally developed as a step change in ultrafine grinding efficiency, the IsaMill™ has made inroads into conventional ball mill and tower mill mainstream grinding duties during the last 5 years - beginning with the Anglo Platinum mainstream grinding projects in South Africa. At the 2006 SAG Conference, plant testwork on the incorporation of IsaMill™ technology into the McArthur River (Northern Territory, Australia) Pb/Zn primary grinding circuit was reported. The IsaMill™ has now become an integral component of that circuit, treating up to 1mm top size feed and directly producing P80 45 µm rougher flotation feed. Two 1.1 MW IsaMills™ are now used in this duty contributing to a 27% increase in overall plant throughput and a reduction in rougher feed size distribution. In this paper, we report on the current state of development and performance of the IsaMill™ in the primary grinding duty at McArthur River and also consider future directions.

Jan 1, 2012

By Lauri Gregg

How Can Man Meet the Carbon-Free Energy Challenge ? ? Increases in Energy Efficiency can displace 1/2 to 2/3 of the Carbon-Free Energy required to stabilize at 550 ppmv ? Renewable Energies require too much land and thus can displace 5 to 10 % of the energy requirement ? Large new sources of carbon free energy are needed ? Conservation is desirable but provides only a small and variable contribution ? People will have to adjust to higher levels of CO2 in the atmosphere as energy demand continues to grow

Nov 1, 2002

By Emile D. L. Rienks

We have studied the interaction of NO with the quasi-hexagonally reconstructed Au(100) surface. Using variable temperature scanning tunneling microscopy we have observed formation of the unreconstructed phase of Au(100) after NO exposure. This NO adsorption induced phase transition is observed in a window of temperatures around 170 K. Under the same conditions, CO and O2 cannot drive the phase transition, suggesting weaker interaction. Thermal desorption spectroscopy experiments provide an estimate for the strength of NO chemisorption on Au(100) of 57 ± 4 kJ mol-1.

Oct 1, 2003

By D. W. Morgan, K. W. Downes

"OVER half a million tons of chromite ore is used annually on the North American continent, all of which is imported from overseas. Chromite is essential in the manufacture of stainless steel, armour plate, and tool steel, to mention only three important uses. It is, therefore, a strategic mineral, and every effort should be made to discover a means of utilizing our domestic supplies.Both Canada and the United States possess deposits of chromite, but they are low grade with respect both to their chromium content and to the ratio of chromium to iron. Mechanical concentration can improve the chromium content •by rejecting gangue, but chromium concentrate produced is still lower in chromium than imported chromite and, more important, the ratio of chromium to iron is only about half that in the imported material. At present, a chromium to iron ratio •of 3:1 is desired by industry. To obtain this .ratio in the case of domestic ores, a chemical attack on the chromi'e is necessary."

Jan 1, 1952

By Pierre Labrecque

Dispatch systems have been used for open pit mining since the early 1980?s but similar systems do not widely exist for underground mining. There is a need for developing dispatch systems for underground mines, particularly highly automated operations such as block caving. An innovative method, Agent Based Modeling (ABM) for a dispatch system for a block caving operation, is proposed in this paper. The model is based on a particular behaviour observed in social insects. The focus of the ABM dispatch system is adaptability with respect to changing operational conditions and effective integration of maintenance modules with the operation. The paper will show the advantages of this innovative method compared to existing similar systems. Furthermore, the preliminary approaches for developing an agent based modeling system for block caving operations are highlighted and discussed in this paper. 1. Introduction In social

May 1, 2008

By E. L. Horner

"Srnoky River Coal is capable ofprocessing 3 million tonnes per year ofrun-of-mine coal at the Smoky River Coal preparation facilities to produce 2.1 million tonnes of high quality, low volatile coking coal for export markets. Multi-seam surface and underground mining operations are scheduled to maintain raw coal feed to the plant. Two beneficiating circuits wash the coal. A heavy medium cyclone circuit cleans the plus 0.5 mm coal and a froth flotation circuit cleans the minus 0.5 mm coal. Clean coal is thermally dried, loaded into unit trains, treated for dust suppression, and transported to west coast port facilitiesf or export. Plant by-products are used as thermal fuel Jn an adjacent power station. Quality control procedures ensure efficient resource recovery for a yield of uniform specification product, at a 7% ash level. Introduction Smoky River Coal operates surface and underground mines in the Smoky River coalfield. Approximately 3 million tonnes per year (mt/ a) of run-of-mine (ROM) coal can be processed at the coal preparation plant to provide 2.1 mt/ a of clean, high quality, low volatile bituminous coking coal. Coal is processed by heavy media and froth flotation cleaning circuits and is thermally dried.Raw Coal Characteristics The characteristics of the ROM coal, both in terms of quality and size consistency, vary with intrinsic seam qualities and mining methods employed. The two seams mined (No. 4 and No. 10) show distinctly different washability characteristics. Seam No. 4 contains relatively few middlings and can be readily cleaned by dense-medium cyclones and froth flotation to give a clean coal at specification ash content. Seam No. JO is more difficult to wash, and the ash content of the clean coal is higher than No. 4 seam at the same operating conditions. However, when the upper I m is excluded from the plant feed, the remaining lower section has washability characteristics similar to No. 4 seam. Coal mined by underground means sometimes contains caprock and consequently tends to be dirtier than similar coal mined by surface means."

Jan 1, 1985

By S. Kawai

Natural convective flow of the electrolyte solution plays an important role in several electrochemical systems. Copper refining electrolysis is the most important industrial process to produce high purity copper on large scale. Turbulent natural convection develops along vertical plane copper electrodes installed in an unstirred electrolyte accompanying with the electrochemical deposition and dissolution of copper during the electrolysis. It introduces the electrolyte stratification phenomenon. Thus, the electrolyte is circulated in a special way depending on each electrorefining tankhouse. The theoretical discussion is indispensable to understand the coupling phenomenon between the ionic mass transfer rate and the morphological variations of electrodeposited copper. In present study, the mass transfer rate of both Cu2+ and H+ ions as well as the momentum transfer rate is numerically analyzed accompanying with the turbulent natural convection along 1 m high Cu metal electrode surface.

Jan 1, 2007

By Jorge Lema Patino

"The purpose of this paper is to determine the best techno-economic alternative for the treatment of tin ores, when comparing the various mining and metallurgical methods of preconcentration, concentration, volatilization (fuming) and up to the final stage of selling to the smelter. The study of the influence of the different parameters of cost, recovery and quoted prices has motivated the paper, which aims at determining the best process of ore treatment in terms of its techno-economic feasibility.Method of WorkOn the basis of head grades of 0.5, 0.75 and 1.0% tin, the following alternative methods of treatment are possible:1. Mining-Concentration-Smelting.2. Mining-Preconcentration-Fuming-Smelting.3. Mining-Concentration-Separation, with direct smelting and fuming/smelting of the two fractions produced.The calculations were carried out on the basis of existing information and publications concerning the various experimental recoveries in the operating mills of COMIBOL. In the case of concentrates containing less than 10% or more than 40% tin, extrapolation was required.The final grade of the tin concentrates and the gross weight of the concentrate were calculated on the basis of the estimated recovery curves. The costs of the preconcentration and the concentration stage s were determined per gross metric ton of material treated.The calculation of the cost of the smelting stage is similar for all the alternatives, the royalties and smelting charge varying with the grade of the final concentrate. In the fuming stage, a uniform recovery of 90% was taken in all cases so as to obtain a final concentrate grade of 65% tin, regardless of the head grade of the feed material.For the separation stage, the following considerations apply:a) Separation can be carried out by gravity separation or flotation methods.b) The cost of separation varies depending on the system used.c) The distribution of tin in the two fractions is 100% at this stage. In other words, there is no loss of tin during separation."

Jan 1, 1982

By M. Bourassa, P. Roy

"This paper describes the automation of Kiena's grinding circuit which comprises an open SAG mill circuit and a closed ball mill circuit with two stages of hydrocyclones. The circuit has been instrumented according to a two level control strategy.The regulatory control strategy is implemented in an industrial controller. This controller does data filtering and calculation (flowrate and solid content) and regulates the pump box levels (2), the water additions: or the pulp percent solids (4) and the fresh ore feed rate.The supervisory control calculates for the industrial controller, the fresh ore feed rate setpoint and the pulp percent solids setpoints in order to optimize the grinding circuit operation. It is made of two modules, one for data filtering and one for control optimization. The filtering program uses modern tools to adjust the measured value and estimate missing data (dynamic material balance, on line estimation of model parameter, etc.). The control program acts as an expert system which combines the benefits of model-based control and rule-based control. A multivariable predictive controller (DMC) is used to maintain the circulating load and the hydrocyclones feed percent solids (which is correlated to particle size) while the rule-based control validates the previous output, detects and avoids the SAG overloads and sump pumps overflows.The system has been operating since MAY 1992 and the benefits obtained are discussed.INTRODUCTIONIn 1990, Les Mines d'Or Kiena decided to go ahead with a project for automating its grinding circuit as proposed by the Centre de recherché minerals (CRM). Its objectives in doing so were to marginally increase production capacity (1 % ) and to create a new challenge for plant staff. The main stages of the project, which involved CRM, Kiena Mines and a consultant, are shown in Table 1. The project was completed in May 1992 with the implementation of a supervisory control system. This text describes the main features of the system with a special focus on its most innovative aspects."

Jan 1, 1993

The Project ? $1.4 billion project ? 59,000 tonnes of nickel and cobalt ? Large resource base ? First production end of 2004 The Place ? Half the size of Vancouver Island ? Population 210,000 ? 43% Melanesian, 37% European, 12% other South Pacific groups, 8% other nationalities ? Tourism principal industry ? 1/3 of world?s nickel resources The Politics ? French Overseas Territory ?1998 Noumea Accord: increased local control over domestic policy ? Referendum on independence in 2014 ? Seeking more economic autonomy, less dependence on French support

May 1, 2002

By D. Kalumba, S. Jjuuko

"Thin Spray-on Liners resist relative small deformations (< 1 mm) between rock blocks or fragments in terms of a combination of shear, adhesive and tensile-bond strengths. Shear-bond strength addresses the ability of a thin liner to resist stresses that act parallel to the rock-liner interface. Therefore quantification of shear-bond strength is essential in the formulation of design standards and requirements for Thin Spray-on Liners. In this paper Thin Spray-on Liner support mechanisms are reviewed. In addition previous methods of Thin Spray-on Liner shear-bond testing are discussed. The paper also explains the research being carried out at the University of Cape Town to investigate the effect of different parameters on the shear-bond strength.INTRODUCTIONRock surface support is widely used to combat rockfalls and resulting injuries and fatalities in the vicinity of active faces (Potvin, 2002), where workers spend most of their time (Adams & Baker, 2002; Potvin, 2002; Lacerda, 2004). The conventional (traditional) surface support systems in underground rock support include passive methods such as mesh and lacing and active methods such as shotcrete. However, rockfall sources between 1990 and 2000 in Nevada gold mines showed a steady increase in rockfall injury associated with mesh support as shown in Figure 1 (Lacerda, 2004). The conventional methods also negatively impact the mining operations with regards to costs, logistics and mining cycle times due to large material volumes (Tannant, 2001; Ozturk & Tannant, 2010; Ferreira, 2012). Therefore, these systems need to be substituted, with enhanced methods, in order to realize the business target of the mining industry of providing the planned return on investment made without harm and within budget."

Jan 1, 2015

By H. W. Little

INTRODUCTION MINERAL deposits of Salmo map-area (Figure 1) have aroused the interest of prospectors for more than a half-century. Properties within the map-area have produced lead, zinc, silver, tungsten, and gold. Sheep Creek mining camp ranks fifth in the Province in the total production of gold, but during recent years interest has been concentrated upon base metals, and meticulous prospecting and exploration have resulted in the discovery of many large zinc-lead orebodies. PREVIOUS WORK Geological investigations of the region were begun long ago, and it is interesting to trace the development of ideas with our increasing knowledge of the geology of this complex area. The first geological examination of the rocks of Salmo map-area was made in 1859-60 by H. Bauerman (1), who was employed as geologist accompanying the first international Boundary Survey. Bauerman examined the rocks exposed along Pend d&apos;Oreille river and published a section indicating that the sedimentary rocks are probably of Palaeozoic age, and are intruded by granite of unknown age. McConnell and Brock(2), in 1894 - 1900, carried out the reconnaissance mapping of the West Kootenay Sheet, on which they outlined the Mesozoic rocks of the Rossland Beaver Mountain volcanic groups that they believed rested unconformably upon the sedimentary rocks to the southeast, which they regarded as of Palaeozoic age.

Jan 1, 1951

By D. E. Gill, A. Piche, S. Dufresne

"SOMMAIREUne méthodologie de prévision des coûuts de forage en galeries est proposée. Cette méthodologie a été élaborée pour les perforatrices pneumatiques manuelles. Elle est composée de quatre modèles: (1) un modèle de pénétration conduisant à la prévision du temps de forage; (2) un modèle d&apos;estimation de la durée de vie des fournitures; (3) un modèle d&apos;estimation de fa quantité d&apos;énergie consommée; et (4) un modèle de calcul de couts. Elle fait intervenir la résistance en compression uniaxiale de la roche du massif foré, le diamètre des trous, Ie type de perforatrice utilise, fa pression d&apos;air d&apos;opération, la longueur des fleurets, les temps morts associes au forage ainsi que le rendement des compresseurs, des perforatrices et du réseau de distribution de l’air comprime. L &apos;application de la méthodologie est illustrée à l’&apos;aide d&apos;un exemple, suivi d&apos;une courte analyse de sensibilité et d&apos;une brève discussion. ABSTRACTA drilling cost estimation methodology for underground headings is described. This methodology has been developed for percussive hand-held drills. It comprises four models: (1) a drillability model used for the prediction of the drilling period; (2) a model for the prediction of bit and rod lives; (3) an energy model; and (4) a cost model. It makes use of the uniaxial compressive strength ofthe rock drilled, hole diameter, drill type used, operating air pressure, drilling rod length, dead times that may occur during the drilling operation as well as compressor, air distribution network and drilling machine efficiencies. The application of the methodology is illustrated with an example, followed by a short sensitivity analysis and brief discussion."

Jan 1, 1994

By Lei Pan, Roe-Hoan Yoon

"Sea water flotation is becoming a reality due to shortages of fresh water. To better understand the mechanisms involved in sea water flotation, we have studied the effects of KCl and MgCl2 on the surface forces present in the wetting films of water formed on hydrophobic surfaces. The measurements have been conducted using the force apparatus for deformable surface (FADS), which is capable of measuring both the surface and hydrodynamic forces responsible for bubble-particle interactions. The results obtained with the gold surfaces hydrophobized with butanethiol (C4SH) show that the wetting films of Ultrapure water do not rupture despite the relatively high water contact angle (??= 80o) and the presence of a long-range hydrophobic force with a decay length (D) of 25 nm in the film. The film is metastable with its equilibrium thickness (he) at 140 nm, where the repulsive double-layer force is equal in magnitude to the capillary force as shown in Figure 1. The film loses its metastability and ruptures in a 10-2 M KCl solution, in which the double-layer force decreases substantially due to the decrease in Debye length (?-1) while the decay length of the hydrophobic force remains as large as 23 nm.The effects of MgCl2 has also been studied using a C4SH-coated gold surface with a water contact angle of 87o. It has been found that in a 10-4 M solution double-layer force decreases due to the decrease in the negative ?-potentials and Debye length, which should help destabilize the wetting film. However, the film remains stable due to the decrease in the decay length of the long-range hydrophobic force from 45 nm in Ultrapure water to 14 nm in the MgCl2 solution. Thus, the results obtained in the present investigation support the view that the difficulties in sea water flotation may be due to the presence of MgCl2 rather than the presence of NaCl in sea water (Ramos, et al., 2013)."

Jan 1, 2016

By Richard C. Williams, Herman Pieterse, Ken Thomas, K. S. Fraser, Ron H. Colquhoun

"The Banick Goldstrike Mines Inc. (Goldstrike) operation is located in Eureka County in north-central Nevada on the Carlin geological trend. Gold in the sulphide mill feed, occurs primarily as submicroscopic inclusions or possibly solid solution in a pyrite and marcasite matrix. Sulphide mill feed is pretreated in a pressure oxidation plant allowing gold recoveries of 90 per cent and greater to be achieved. Anticipated 1994 gold production for the sulphide gold facility is approximately 1,500,000 ounces.In January 1989 American Banick Resources Corporation (Banick) announced the US$365 million Betze Development Plan for the Goldstrike property. The Betze plan was based on a three (3) staged expansion of the original 4,500 STPD oxide gold plant. This expansion would involve addition of ore and gold processing capacity and the total conversion of all ore handling facilities to treating Betze sulphide ores.Phase 1 of the Betze Development Plan involved the construction of a pressure oxidation circuit, including a single autoclave and supporting ancillary services. The pressure oxidation circuit was commissioned in February 1990. Currently a throughput of 2,000 STPD is being achieved.Phase II of the Betze Development Plan, commissioned throughout April and May 1992, included the expansion of grinding, leaching, and gold recovery facilities enabling the treatment of combined oxide, and sulphide ore. Pressure oxidation capacity was increased by the addition of two (2) autoclave circuits each treating 2,600 STPD of sulphide ore and other required ancillary services. By June 1992, the Phase II gold facility had achieved a combined throughput of 15,000 STPD of oxide and sulphide ore.Phase Ill, the final stage of the Betze Development Plan, was successfully commissioned in February and March 1993. This final stage of development increased the design throughput of the pressure oxidation plant to 15,000 STPD by the addition of three (3) autoclave circuits with combined capacity of 7,800 STPD."

Jan 1, 1994

By G. Vibert Douglas

"Gold occurs in Nova Scotia in three ways, saddle reefs, fissure veins, and fossil placers. Of these the saddle reefs are the commonest. They have been the source of most of the gold and have also been the subject of most of the literature on the gold occurrences.The Meguma or Gold-bearing series of Nova Scotia is a conformable succession of quartzite's and slates, possibly Precambrian in age, which have been folded into a number of anticlines and synclines that strike (Fig. 1) roughly east and west. This folding has been termed Acadian and is probably a westward continuation of the Caledonian revolution in Britain. It may have started in the Ordovician and continued through the Silurian and into the Lower Devonian. It was followed by the intrusion of the great Devonian granite batholiths. It is thought that the mineralization is connected with the late phases of the cooling of the granite. As the name saddle reef implies, the veins form on the crests and flanks of the anticlines, possibly in the synclinal troughs as well. The beds favoured by the solutions are the slates. The reason for this is apparent when it is realized that in order to fold over 30,000 feet of sediments (the thickness of the Meguma according to E. R. Faribault) through p radians of arc it is necessary to have a differential movement between the top and bottom beds of p times the thickness of the sediments. In the case of the Gold-bearing series, in which strong quartzite beds lie between incompetent slate beds, most of this differential movement was taken up in the slates. The evidence for this is the remarkably fine drag folding and the intense shearing and comminution of some of the beds of slate (Fig. 1). The quartzites exhibit some shearing and faulting, but there is little doubt that the greater permeability lay along the incompetent slate beds. The mineralizing solutions followed these beds and also passed from one slate bed to another through a joint or fault in the intervening bed of quartzite. These joining veins are called angulars in Nova Scotia. Within the veins the gold is in shoots and the real problem is to find out what controls the position and extent of the shoots."

Jan 1, 1954

By William M. Luff

"The Bathurst area has recorded mining production as early as 1837, although the bulk of the production has come in recent years. Production has been mainly from the well-known massive sulphide deposits, but vein, gossan, and a variety of other deposits have also been mined. This paper summarizes the history of the mined deposits, along with tonnages and grades produced. A number of ""firsts"" have been noted in the Bathurst area. The A Zone deposit, located in the Heath Steele area, was the first in the world discovered using airborne electromagnetic methods. Heap leaching of gold from the gossan zone at Caribou was the first operation of its kind in Canada. The Keymet mine was the first base metal (lead-zinc) mine in New Brunswick. For the past few years, the Brunswick No. 12 mine has been one of the largest zinc mines in the world.IntroductionThe Bathurst area (Fig. 1) first had mining production in 1837 when copper was mined from a deposit on the Nepisiquit river (MacKenzie, 1958). The majority of the production, however, has been in recent years from massive sulphide deposits, but there are also other significant operations. . Table 1 is a summary of Bathurst area mineral production, showing concentrator feed tonnages and mill feed grades. The table does not include peat deposits, sand and gravel, dimension stone or rock quarries. Figure I is a general geology map of the Bathurst area, indicating deposit locations. The deposits are divided into four categories: massive sulphide, vein, gossan and other. The deposits in each category are described in chronological order of exploitation."

Jan 1, 1995