Search Documents

By J. Kramer, T. Hartmann

In the Hydrometallurgical processes, the presence of the so-called “crud” is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design. The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the seriesconnected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation. The transfer of the organic phase into the electrolysis cell can result in a “burnout” of the cathode. The carry-over of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show. To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl®. By this means, we can guarantee our customers the maximum possible solvent recovery and minimise the solvent costs in this process step. This system is presented in detail in this paper.

Jan 1, 2012

"AbstractThe Sedimentary Basin area of Western Canada, which lies between the Precambrian Shield and the Cordilleran mountain area, covers approximately 800,000 square miles. Sediments ranging in age from Cambrian to Tertiary are present and, of these, horizons in the Upper and Lower Cretaceous, Jurassic, Mississippian, and Devonian have yielded commercial oil and gas flows. Producing horizons in the Cretaceous and Jurassic are sandstone, while all those of the Palaeozoic are carbonate rocks such as red limestone or dolomite (bioherms). Shows of oil and gas have been encountered also in the Cambrian and Triassic sediments.The broad structural features of this vast expanse of sedimentary rocks are the Moose Jaw syncline, the Sweet Grass-Battle River arch, the Alberta syncline, the Foothills belt, the Rocky and Mackenzie mountains, the Great Bear-Slave Lake basin, and the Mackenzie Delta Basin area.This contribution outlines the .stratigraphy and structure of the Basin area, and gives examples of present producing oilfield structures and stratigraphic traps.Part 1.-Regional StratigraphyIntroductionThe vast expanse of relatively undisturbed sedimentary rocks of western Canada has long been recognized as prospective territory to search for oil and/ or gas. This search in western Canada dates back before the turn of the century, but, considering the size of area to be explored and tested, the effort an<l money expended upon it, which, before the recent discovery of oil at Leduc, Alberta, appeared large and fruitless, now seems almost ridiculously small. A check-up of effort and money expended prior to and since the Leduc discovery would undoubtedly reveal that more wildcatting and development has taken place during the last two and a half years than during all previous years combined. The figures would astound not only the average citizen, but many within the industry itself."

Jan 1, 1950

By Colin Harvey

The paper industry in the Pacific Northwest is a potentially large market for industrial clays. Current trends within the paper industry towards higher quality newsprint, filled and coated papers, offers an incentive for exploration in the region since the current supply of kaolin is mainly from Georgia in the southeastern U.S. Freight rates commonly exceed US$100 per tonne. The kaolin resources of the Pacific Northwest require expensive processing technologies to meet the industry specifications and it is doubtful that any large development of the local resources can be supported at the present time. Competition from high-quality regional resources of carbonates is another factor weighing against the development of local kaolin resources while there is a potential threat from shipments ofAsian and Brazilian kaolin in the early part of the 21st century.

Jan 1, 2001

By T. Rigg, J. N. Stone

"The process described has been developed to utilize low-grade scrap -turnings, borings, tin cans and other types of ferrons scrap which currently has been of limited or no use in conventional steelmaking processes. If scrap of this type can be converted into high-purity iron by chemical means then there is a potential saving of several million tons of metal annually in North America.The process is chemically quite simple and consists of dissolving ferrons scrap in hydrochloric acid, followed by evaporation and crystallization of the resultant solution to yield ferrons chloride crystal.s. These crystals are dries, briquetted and converted to non sponge by reduction in hot hydrogen. The HCl produced from the reduction step. is absorbed in water and the hydrochloric acid so produced is returned to the dissolver circuit. The hydrogen produced from the initial dissolution of the scrap is used to reduce the ferrons chloride. Purity is maintained by bleeding off impure chloride solutions from the evaporator-crystallizer circuit, and converting these chlorides to oxides and HCI in a high-temperature spray roaster. The HCl produced in the roaster is absorbed in water and the hydrochloric acid returned to the dissolver."

Jan 1, 1970

By D. M. Baird

ABSTRACT A revised stratigraphic section of Carboniferous rocks which occupy about 700 square miles in southwestern Newfoundland is presented. Gypsum, which outcrops at thirty-five different localities, is found to belong to four principal zones in the section. The newly mapped structure of the region makes the otherwise random occurrences of gypsum appear as systematic outcroppings of the four zones which follow the regional structure. Details of several occurrences are given and those most advantageous for exploitation are pointed out. INTRODUCTION ROCKS of Carboniferous age occupy an area of about 700 square miles in southwestern Newfoundland. They occur in a belt, from 5 to 15 miles wide, which extends from the head of St. Georges bay southwestward for 65 miles to the mouth of Little Codroy river (see Figure 1). Several hundred feet of Pennsylvanian rocks overlie rocks of Mississippian age, which are at least 12,000 feet thick. The rocks of the Carboniferous section of Newfoundland are very similar to those of Nova Scotia and represent a northeastward continuation of the same palaeophysiographic conditions. Mississippian measures of Windsor equivalence include thick gypsum deposits which outcrop at many places and which extend under large areas as indicated by sink-holes and by structural considerations.

Jan 1, 1951

By C. W. Drake, J. H. Walsh

"The Canadian Carbonization Re-search Association was formed during 1965, with seven founding members representing four integrated steel companies, two coal companies and one high-temperature tar processing company. The purpose of this paper is to review the circumstances which led to the formation of this new research association and to discuss its general objectives. Also discussed will be the organization of the Association, the nature of its relationship with the Department of Energy, Mines and Resources in the early stages, and some of the technical programs which have now been initiated."

Jan 1, 1967

By C. Robinson

The Diavik Diamond Mine is located in one of the most remote and forbidding places in the world, 220 kilometres south of the Arctic Circle and on the bed of a vast northern lake, Lac de Gras. A single road, built out of ice and crossing frozen lakes, connects the mine with other operations and Yellowknife, the capital of the Canada&apos;s Northwest Territories. Diamonds were first discovered in the Lac de Gras region in the early 1990s, and construction of the Diavik Diamond Mine was completed in 2003. Diavik currently mines three kimberlite pipes. Open pit mining has now concluded and all three pipes are mined using underground mining methods. In early 2010, Diavik began mining and processing initial ore from its new underground mine; underground mining operations are expected to continue beyond 2020. The initial mine ventilation system was an exhausting (pull) system with fresh air supplied by a fresh air raise and a main ramp. Return air was exhausted via two raises and a secondary ramp. The system had a total flow capacity approximating 401-411 m3/s. With planned increased production and with changes in mining method, it has been proposed to change the mine ventilation system to a positive (forcing) ventilation system in order to meet projected increases in flow requirements of 566-708 m3/s. Extensive engineering work was developed in order to successfully achieve the changes in system configuration. In the proposed configuration, the main ramp is in an exhaust configuration and exhaust raises are converted to fresh air raise. A number of system implementation options were investigated and phased plans for system execution have been developed. The proposed changes to the ventilation system are substantial and involve extensive construction work. Work was commenced in 2011, each planned phase has been successfully completed to date, and system changes continue today in order to achieve complete system flow reversal and increased flow distribution. This paper details the design of the modified ventilation system and commissioning work which will allow the mine to meet its future production targets.

Aug 1, 2013

By G. G. Bowser

PERUSAL of a list of present-day commercial explosives perhaps does not convey a full realization that there has been a great deal of improvement since the original dynamite was discovered nor that, in recent years, great developments have taken place in specialized explosives. This is true particularly of high-explosives for use in metalliferous mining or what is more commonly termed &apos;hard-rock&apos; mining. Not many decades ago, only two or three types of explosive were avail-&apos;able for commercial use. One was black blasting powder. Another was ordinary nitro-glycerin dynamite in various strengths. Black blasting powder remains with but very little change. Despite its ancient lineage, it is still with us as perhaps the sole explosive in use today which is almost identical in appearance, physical properties, and working ability or execution co the original. Which dynamite the story is different. Its evolution may be likened to that of the dog, nitro-glycerin as first discovered being the counterpart of the wild dog and, like it, dangerous and hard to control. The original dynamite as made by Nobel might then be considered as representing the first domesticaced species. This original dynamite, however, has been &apos;crossed with other bloods&apos; until one sees now many distinct &apos;breeds&apos; in the list. Present-day explosives still have the &apos;bark&apos; and the &apos;bite&apos;, but with control and research have come many improvements; and types have been created which are specially adapted for particular kinds of work. We still have the direct descendant of Nobel&apos;s dynamite in the form of an improved nitro-glycerin dynamite. This C-I-L explosive, Polar Dynamite, is no longer the best type to use in the hunt for gold, silver, iron, and other metals. There have been developed other explosives more suitable for chat work. In Canada, such explosives are accomplishing this work effectively, not only where climatic conditions are moderate but through the rigours of our northern winters, with their sub-zero temperatures.

Jan 1, 1938

By P. A. Distin, Jr. da Silva

The history of commercial processes for zirconium/hafnium production and separation is reviewed. A new technology is then proposed as a potential alternative for zirconium/ hafnium separation in a simpler, cleaner way than achieved with current processes. Primary sources of zirconium always contain small amounts of hafnium that must be removed during production of zirconium metal for nuclear applications. This separation is usually carried out by a solvent extraction process, developed in the 1950s, that selectively extracts hafnium, as a thiocyanate complex, using methyl isobutyl ketone (MIBK). Environmental problems inherent to this process are the high aqueous solubility and low flash point of MIBK, and possible gaseous contaminants formation generated by the decomposition of the thiocyanic complexes in hydrochloric acid medium (H2S, HCN, mercaptan’s formation). The present work shows how these problems could be avoided by using organophosphorous extractants that were unavailable when the MIBK process was developed.

Jan 1, 1998

By H. U. Ross

ROASTING is usually thought of as a process in which finely crushed or ground ore is heated with air in a suitable furnace in which the ore is rabbled or agitated in such a way as to insure complete reaction between the oxygen of the air and the oxidisable constituents of the ore. Roasting in this sense is used only to a very limited extent in the iron and steel industry. This is because, in most iron ore deposits mined today, the ore is of a type that does not require roasting. Where this process is used, it is usually because of some special circumstance, such as a peculiar economic condition, that warrants it. If roasting is looked upon in the broader sense as a gas-solid chemical reaction carried out at an elevated temperature in which both gaseous and solid products are formed, then the process is used in the iron and steel industry to a greater extent

Jan 1, 1961

By O. Worku, J. H. Masliyah, Z. A. Zhou

ABSTRACT The viscosity of concentrated kaolinite or illite clay in aqueous suspensions was measured in the presence and absence of a small amount of montmorillonite (<1 wt%). To avoid solids settling and to increase the sensitivity of the suspension viscosity measurements, solids concentrations higher than 38 wt% were used. The pH of the suspensions and the concentration of calcium and bicarbonate ions were found to significantly impact the viscosity of the clay suspensions. The results showed a significant increase in the viscosity of kaolinite suspensions with the addition of as low as 0.25 wt% of montmorillonite on a solids weight basis. In addition to illustrating the role of water chemistry in modifying slurry rheological properties, our study demonstrated that viscosity measurement could be a simple, yet sensitive technique for determining the content of smectite clays, such as montmorillonite, in a complex mix of various types of clay.

Jan 1, 2012

By W. F. McDermott

This paper covers the development, construction and operation of a 53-mile slurry pipeline operating in Tasmania, Australia. Special development techniques are discussed, as well as the operation of this line and its impact on transportation from remote areas.

Jan 1, 1970

By Robert A. Macinnes, Peter Moon, John P. Pappone

"This paper, in presenting the results of the application of the assessment centre method at Texasgulf Canada Ltd., illustrates a novel "" in-use"" technique for manpower training in the mining industry.IntroductionMining history is full of examples of what goes wrong when human judgment fails-disasters, floodings, loss of life and property. We must, therefore, assume the importance of selecting competent people for supervisory responsibility. This article de scribes a method for assessing supervisory ability, its first application in Canadian mining and the result s obtained over the past six years. It is known as the assessment centre method."

Jan 1, 1981

By Frank E. Lathe

During the war the National Research Council at Ottawa sent out questionnaires to the managers of nearly all the industrial plants in Canada. Inquiry was made as to the research equipment possessed, the number of research workers employed and the nature of the research problems which still remained unsolved. Practically all the companies reported that they had no special facilities for research, had no re-search workers and did not require the assistance of the National Research Council-because they had no research problems. Perhaps we have here one of the chief reasons why certain of our manufacturers find themselves unable to meet foreign competition. For hundreds of years the Indian tribes of northern Chile worked, in a small way, the copper deposits at Chuquicamata. They had no research problems and made no striking success of their mining operations. Then came an American company with a research problem, which they proceeded to solve. To-day the stock of that company has a market value of about $140,000,000.

Jan 1, 1926

By C. E. White

The depletion of higher grade mineral reserves will accelerate the trend toward production from progressively larger and lower grade deposits. The discovery of adequate reserves of leaner ores will require the development of improved exploration techniques with a greater depth range. The principal challenges to the Canadian mining industry are to find the mineral resources required to meet fast growing world demand and to develop mining methods and equipment to ensure production costs which will strengthen our position in export markets in the face of in-creasing world competition. The challenges cannot be met without intensive efforts to attract more technical men to the industry and to improve their training.

Jan 1, 1967

By W. G. Brissenden

"ALTHOUGH I SHOULD FIRST REVIEW the state of the mining art as it is today, because of the shortness of time I will confine myself to a re-view of the more important advances in that art which have been made in the past two to three decades. Then, a look at the opportunities and the challenges which now present themselves will be more meaningfulFirst, some of the more impor-tant developments in underground mining:(1) The recognition that good ventilation, visibility and working conditions are essential preliminaries to efficient production has resulted in their incorporation as a matter of practice in modern mine planning. (2) The introduction of the car-bide bit and the re-introduction of the airleg drill, and the resulting sharp rise in productivity, were early postwar developments. (3) The recovery of the coarser fraction of mill tailings for use as mine backfill also is an important cost-reducing development of recent years -and this has led to cemented backfill, which, al-though more expensive, meets certain specific needs and has tremendous potential. (4) Great strides have been made in improving explosives' materials and explosives' accessories. Millisecond-delay electric blasting caps, which improve fragmentation and reduce the seismic effect of blasting, and the development and •application for underground use of explosives are but two among many such improvements. (5) Trackless mining methods, using quarry-type equipment in some instances and specially de-signed low-headroom trucks, loaders and carrier-mounted drills in others have been successfully applied. (6) Dual-purpose load-haul units are now in use loading and hauling from open stope drawpoints, and smaller versions of this type of unit are in use in cut-and-fill and other types of stopes."

Jan 1, 1968

By E. G. Leonardon

The question of geophysical prospecting is one that is beginning to occupy a pre-eminent place in the minds of those actively concerned in the discovery and exploitation of ore deposits. This is in marked contrast to the reception accorded such ideas when the Junior author, six and a half years ago, began introducing electrical prospectii1g to the mining fraternity on this continent. Happily, the mention of geophysics no longer evokes the sceptical and pitying smiles that it did in those days. A little reflection will show that modern geophysical methods are merely a logical development from pre-existing technique. In the study of geological problems, is it not logical to use all possible physical properties of matter? The study of crystal form and cleavage, the examination of thin sections of minerals by means of polarized light or ordinary light, in fact, utilize physical properties of minerals for the benefit of the geologist. These are, of course, laboratory methods, and the extension of the study of similar properties into field work was inevitable. This began with the magnetometric surveys, used as early as 1760 in New Jersey to locate iron ores. Eighty-four years later, John Locke&apos;s work in the United States resulted in pointing out relationships between the terrestrial magnetic field and main tectonic features of the earth&apos;s crust.

Jan 1, 1928

By L. E. Djingheuzian

ANON-CATARACTING (N-C) ball mill is so operated that the balls are not thrown in-ward at the top of their paths. The result is to maintain, in the mill, a quiescent pool in which classification will occur at a limiting size corresponding to the pulp density. N-C operation is produced by effecting proper relationship among mill speed, ball diameter, volume of ball load, and pulp density. Such operation is typified by the primary ball-mill operation of the Tennessee Copper Company, Copper-hill, Tenn., and the Cleveland Cliff Iron Company, near Ishpeming, Mich.

Jan 1, 1958

By S. G. Luckey, N. R. Harrison, F. Nadeau, U. Brüx

"The adoption of tailored-rolled or tailor-welded blanks (i.e. TRB/TWB) in the automotive industry has been known to offer great potential for the optimization of weight, function, cost and complexity. Vehicle light weighting can further be achieved by using high strength aluminum alloys like the 7xxx-series. 7xxx-series alloys are capable of delivering specific strengths equal to or greater than high strength steels. However, room temperature formability of this aluminum class is limited, so one approach to forming 7xxx-series alloys is by hot stamping. Hot stamping utilizes an elevated temperature blank and the high pressure stamping contact of the forming die to simultaneously quench and form the sheet. This paper explores the initial feasibility of tailored thickness material for body-in-white applications when processed under hot stamping conditions.INTRODUCTION Steel tailor-rolled blanks (TRB) or tailor-welded blanks (TWB) have been used within the automotive industry as a method of reducing weight, expanding material utilization, and decreasing overall part/assembly cost (Ganeasan et al., 2015; Merklein et al., 2014; Hirt et al., 2005; Kridli et al., 2000). The production of such tailored thickness materials has resulted in over $2.5 billion (2016) in combined industry sales (Mubea, 2018). As automakers begin to adopt the manufacturing practices traditionally reserved for steel such as tailor rolling/welding with greater enthusiasm for vehicle light weighting, there exist an opportunity to expand the material database to extend beyond the traditional aluminum alloys found in current production. High strength aluminum alloys, i.e. 7xxx-series, are ideal for structural automotive applications due to their high specific strength; however, they have limited room temperature formability. Hot stamping, another manufacturing practice used by the steel industry, can be used to form these high strength materials. The combination of tailoring the thickness of a sheet material and hot stamping provides an opportunity for significant weight saving within an existing manufacturing footprint. This paper explores the potential and challenges of this approach when applied to structural body-in-white components. The methods for tailor rolling, tailor welding and hot stamping are described and applied to the production of a 7075 aluminum alloy B-pillar. The results are discussed in terms of feasibility and weight savings."

Jan 1, 2018

By Unkown

To the Membership of the Institute Gentlemen: The Mineral Industry of Canada in 1948 The preliminary estimate issued by the Dominion Bureau of Statistics and tabulated in the Bulletin of January, 1949, indicated that the value of Canada&apos;s mineral production in 1948 reached an all-time high of $808,180,216, showing an increase of 25 per cent over the previous record of $644,696,007 established in the preceding year. The output value of metallics was increased by 22.4 per cent; of fuels, by 43.7 percent of other non-metallics, by 19 per &apos;cent; and of structural materials, by 16.8 per cent. The value of metals produced in 1948 at $483,770,759, was about $87,000,000 more than in the previous year. There were substantial increases in the tonnages of copper, lead zinc nickel, and other base metals produced, but the rises in market prices for such metals accounted for most of the gains in output values. Production of gold at 3,495,403 ounces valued at $122,339,105 indicated an increase in volume of approximately 500,000 ounces and an increase in value of 14 per cent. Despite the benefits provided under the Emergency Gold Mining Assistance Act 1948 the volume of gold produced in the year was still nearly 2,000,000 ounces less than the record of 5,300,000 ounces established in 1941. The value of mineral fuels produced in 1948, at $158,787,255, was 44 per cent above the 1947 total. Coal production at 18,431,250 tons valued at $107,298,757, while substantially higher than in the preceding year was still half a million tons below the record reached in 1942. Striking developments in the Leduc field in Alberta were responsible for bringing the output of crude petroleum in the year to a new high of 12,098,166 barrels, valued at $36,858,959.

Jan 1, 1949