Search Documents

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, F. J. Tavitas-Medrano

319-type cast Al-Si-Cu-Mg alloys are commercially important due to their popular use in automotive applications. Artificial aging heat treatments are commonly performed in these alloys to achieve precipitation hardening and, therefore, improve their mechanical properties. The present work was carried out to investigate the effect of conventional (at a constant temperature, as specified by the standard T6 heat treatment regime), and non-conventional multi-temperature and interrupted aging cycles on the hardness, tensile and impact properties of two 319-type alloys (with and without Sr+ Mg additions). The results show that certain multi-temperature aging cycles have a more favourable effect in improving some mechanical properties than conventional cycles.

Jan 1, 2006

By A. J. Hargraves

"It is difficult to quantify comparatively the gassiness of a property. The most common index to gassiness, cubic feet of gas per ton of coal mined, is very arbitrary and does not take into account the geological setting nor the mining operation. The gassiness of a virgin coal in situ can be assessed, but no method is precise and the most accurate methods involve prolonged field and laboratory experiments. In general, gassiness increases with depth. Whereas 'gas' normally implies methane, other gases such as nitrogen, carbon dioxide, etc. may be present in seam gas also. The inflammability of methane is a problem, particularly the explosibility of a methane-air mixture; also oxygen dilution is involved in high gas concentrations and some gases are poisonous even in low concentrations. Cross measuring into a virgin seam is usually not as troublesome as development in the seam, where narrow openings may require strong ventilation to dilute gases exuding from the face and sides. Total extraction presents problems of gas from the working seam, or from adjacent seams, particularly at the return side, or of gas-laden air from the goaf streaming out or sometimes surging out intermittently, again on the return side. In pillar extraction or longwall retreating special roadways may be required to allow the side-to-side and end-to-end flushing of the goaf which is somewhat inherent in longwall advancing. Layering may occur, particularly where ventilation conditions are not brisk. Outbursts of gas from adjoining seams may be induced by sudden rupture of roof or floor in caving workings. Outbursts of coal and gas from the working seam may occur, mostly in development work, under special environmental circumstances. Gas problems may be reduced or eliminated by predrainage of gas ....:. rarely successful from the working seam - usually undertaken from adjoining seams prior to escape of gas released by caving. The ideal solution - general predrainage of gas to the surface from measures prior to mining - has yet to be accomplished. • In the planning of gassy mines it is possible to make an assessment of gas contained in the seams and to estimate what proportion will be released into the mine air, but emission of gas into mine workings is never steady and at present there is no better planning criterion than experience at the mine next door!"

Jan 1, 1973

By C. Ciriello

Six Sigma methodology, as applied within Xstrata (formerly Falconbridge and Noranda), involves a disciplined approach to managing projects, solving problems, improving performance, and leveraging information. The four (4) cornerstones of Six Sigma are the use of Philosophy (customer driven, desire to improve and discipline), Metrics (measurement systems), Methodology (scientific method and sequence of deliverables), and Tools (such as statistics, change management, and root cause analysis). This paper will outline the general steps of the Six Sigma methodology and demonstrate how each phase directly applies to a real plant metallurgical project aimed at reducing nickel losses of the rougher flotation circuit at Raglan. The main concepts of Six Sigma are described, along with the specific challenges, successes, and deliverables related to the project. It is also the authors' aim to demystify the basic Six Sigma principles.

Jan 1, 2007

By Dwayne D. Tannant

This paper presents a summary of results from a questionnaire sent to surface mines in western Canada seeking information on haul road design, construction, and maintenance. There has been a marked increase in the size of the trucks used over the last decade with some mines now using trucks with a payload capacity of 360mt. Consequentially, geometrical elements of haul roads, such as width, have been enlarged to accommodate larger trucks. Most haul roads are constructed on the basis of past experience without use of formal design procedures. With the introduction of larger haul trucks, problems related to rolling resistance, deterioration, and maintenance of the haul roads have become more important. This has lead to adoption of more rigorous design methods for roads at some mines, most notably for the oil sand mines operated by Syncrude Canada Ltd. A summary of the evolution of haul road designs implemented at Syncrude Canada Ltd. is presented.

May 1, 2001

By Michio Okada

Dissociative adsorption of hydrogen (deuterium) on thin gold films grown on Ir{111} surface has been studied with temperature-programmed desorption using a quadrupole mass spectrometer and nuclear reaction analysis. Thin Au{111} films are epitaxially grown on Ir{111}. Surprisingly, H2 (D2) can dissociatively adsorb on these Au{111} films, although it is well known that Au surfaces are noble enough not to dissociate hydrogen molecules [B. Hammer and J.K. Nørskov, Nature 376, (1995) 238]. We attribute this to the sensitivity of hydrogen to changes in the local surface properties, e.g., electron localization (the narrowing of the s-band, the s-band center model), which could explain the upto now unexpected high for the reactivity of a thin Au{111} surface. Moreover, we found that H (D) atoms can be confined into a Au thin film and/or the interface between an Ir surface and the thin Au film. We demonstrate how anomalously reactive thin Au films grown on an Ir surface are, and also compare the Au films with Ag films grown on Ir to test the validity/generality of our proposed s-band center model.

Oct 1, 2003

By Hooman Askari-Nasab

Open pit mine plans define the complex strategy of displacement of ore and waste over the mine life. The objective of the mine plan is to maximize the future cash flows within the technical and physical constraints. Various mixed integer linear programming (MILP) formulations have been used for production scheduling of open pit mines. In the MILP formulation the slope constraints guarantee that all the overlying blocks are mined prior to mining a given block. Traditionally, the slope constraints have been modeled with cone templates representing the required wall slopes of the open pit mine. The overall pit slopes constructed by these templates are a function of the width and height of the geological block model. Therefore, the overall slopes are fixed in one bearing. This paper presents a general MILP model for open pit mine scheduling with variable slopes constraints. The methodology utilizes a directed graph to capture the precedence of extraction of blocks and pit slopes in different bearings. Depth-first-search algorithm was used to traverse the graph for constructing the slope constraints in the MILP problem. TOMLAB/CPLEX was used as the implementation platform to efficiently integrate the mathematical solver package CPLEX with MATLAB. A case study on intermediate scheduling of an iron ore mine over twelve periods was carried out to validate the models.

Oct 1, 2009

By R. Binning

"Economic high density mineral reclamation and subsequent transportation of solids through a pipeline presents many formidable engineering problems.Mineral reclamation system design by theoretical formulas is almost impossible because solids composition, ie. concentration, velocity, moisture content, solid size, etc. can only be controlled within a broad pumping range.Traditionally this has restricted pumping to relatively dilute slurries whereas it is usually preferred, because of economic considerations to reclaim as high a concentration as possible.At Toyo/De-Velde Corp. we recognized these pumping limitations and began to develop and manufacture a range of standard and auxiliary equipment that would exceed these technical restrictions.MATERIAL RECLAMATION & PIPELINE INJECTIONTo minimize fluid usage and increase material reclamation efficiency we designed a submersible dredge mixing pump that uses most of its energy to pick up material from rest, mix it with fluid into a highly concentrated slurry then push it firmly into a pipeline.Where material is too compacted to be mined by the standard submersible mixer pump, auxiliary high torque self contained submersible excavators can be fitted around the periphery of the mixer pump. This is to facilitate excavation and break up of the compacted material into a slurry.High flexibility of this system can be achieved by combining the many equipment variations available into the most efficient format to fit individual site requirements.Whatever combination of equipment is selected, torque is nullified by counter rotating excavators against each other. This increases effective excavator/material bite torque but also allows mixer/excavator rig suspension by cable for deep water material recovery."

Jan 1, 1985

By T. Ward, K. Shah, K. Murray

The mining industry is processing deposits with ever decreasing grade at ever increasing operating costs while margins are under constant pressure by material substitution and recycling. We are reaching the point where building it bigger just isn’t good enough as social and environmental constraints become more intense. In response to the growing demands on our industry, Goldcorp has embarked on a journey to increase resources by converting Waste to Ore. Gravity pre-concentration and sensor sorting testwork has been completed on samples from our Canadian operations in order to determine the amenability of our mineralized waste to sorting and upgrading. As expected some material was amenable to sorting and a review of the economics supported demonstration plant testing. The ability to economically sort mineralized waste into ore and barren rock is being demonstrated by Goldcorp. It has been made possible by leveraging the experience mineral sizer manufacturers have gained in the oil sands and hard rock applications, seeking more energy efficient screening machines and embracing the advancements that ore and recycling sorter suppliers have achieved. The paper will discuss the testwork and results achieved to date from both the lab and demonstration plant.

Jan 1, 2018

By J. Bhattacharya, S. K. Mukhopadhyay, S. K. Pal

"While time and again many authors have categorically stressed the restoration of the environment, very little effort has been made in the mineral industry to develop the economy of environmental control. There are many abatement procedures that search a maze of variants. Among them pricing environmental damage seems to be more logical and easily implementable.IntroductionMining as an operation has a severe impact on the Earth's natural resources. While economical environment control is much sought after, solutions are often varied and complex, and can differ in the problems of single or multiple mine sites.Determination of Optimum use LevelsIn “mining environmental control"" it is required to strike a balance to find optimum use levels. The solution is to find where the welfare benefits equal the cost involved to curb the degree of environmental damage (Fig . I) . In the mining industries this can be done by modifying the production/extraction process itself. For most pollutants, the marginal costs of control will exceed the benefits from further reduction of damage long before the zero pollution damage point is reached (Fig. I). From an economic perspective the optimal alteration of environment by mining would occur at z; pollution continues to be caused by ""zy"" control units, but it would be inefficient to pursue the redemption efforts further because the marginal cost involved would exceed marginal welfare benefits."

Jan 1, 1992

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By B. K. Gorain

Barrick' s Buzwagi copper-gold deposit in Tanzania comprises oxide, saprock and sulphide mineralized zones averaging approximately 0.058oz/t gold, 0.13% total copper and 0.03% cyanide-soluble copper. A comparative evaluation of the project based on two potential flowsheet alternatives is presented. The first flowsheet included a gravityconcentration and carbon-in-leach (CIL) plant. The second flowsheet was based on a Gravity-Flotation-CIL plant, which proved to be more economically robust. Selective flotation of copper minerals to produce a saleable copper concentrate proved to be challenging. Detailed characterization of the Buzwagi deposit was carried out through understanding of ore mineralogy, mineral liberation, floatability and selectivity, reagent chemistry and regrinding issues. With this insight, a flotation concentrate of greater than 25% Cu was achieved, recovering a significant amount of copper minerals and tellurides. The overall economics of the project improved significantly with the addition of flotation. Leach tests on gravity and flotation tailings showed an overall increase in gold recovery of approximately 6% for a Gravity-Flotation-CIL plant compared to that for a Gravity-CIL plant.

Jan 1, 2007

By A. B. C. Stothart

"IntroductionIn the past four years Ontario Mines have made great progress in the development of reliable mine conveyance safety dogs. History shows that, prior to 1945, a rope failure on a descending conveyance was usually followed by unsatisfactory safety dog operation.It is proposed in this paper to discuss briefly;The history of this development. Progressive .development of one type (E. Long).Free fall testing of safety dogs. Anti-trailing rope device.HistoryOn February 2nd., 1945, a hoisting rope broke at the Paymaster mine. The safety dogs proved ineffective and permitted the cage to crash through to the bottom of the shaft, with disastrous results.Following this accident, the Ontario Government appointed a Technical Committee to investigate The Safety of Hoisting Equipment and Hoisting Practice in Ontario Mines. This Committee consisted of Dr. C. R. Young (Chairman) and Professors T. R. Loudon, E. A. Allcut, V. G. Smith, and Lloyd M. Pidgeon. The Ontario Mining Association (at the request of the Ontario Government) also appointed a Committee consisting of Messrs. R. E. Dye, R. D. Parker, and R. L. Healy."

Jan 1, 1950

By Etienne Roy Grégoire

Since the early 1990s, the Canadian mining industry has been increasingly defined by the signing of Impact and Benefit Agreements (IBAs) between mining companies and Aboriginal peoples. While these agreements are intended to complement the legal system, they also serve to establish the legitimacy of mining projects and to encourage the harmonious integration of these projects into their social and environmental contexts. Beyond their practical implications, what are the effects of such agreements on the ability of Aboriginal communities to access the institutional space where the authorization of mining projects and the conditions of their implementation are decided? Can we view IBAs as a preliminary step towards the operationalization of the principle of Free, Prior and Informed Consent? This paper aims to explore the potential of IBAs as a sustainable solution to the legitimacy issues that result from the implementation of the formal regulatory framework governing mining activities in this jurisdiction. We highlight what constraints and opportunities the James Bay and Northern Quebec Agreement (JBNQA) engenders for local communities and draw attention to the ways in which the negotiation of the Raglan IBA and the environmental evaluation processes act upon each other. We find that certain structural problems - and problems of legitimacy ? related to mining in Northern Quebec cannot be solved by the sole signature of an IBA, which suggests the need for caution when considering such agreements as a panacea. The Raglan case demonstrates that IBAs, like other modes of regulation relying on the direct interface between companies and communities, would benefit from a stricter framework and more explicit ties with official regulation channels.

Aug 1, 2013

By Joel Werner

Weak metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as: remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

May 1, 2003

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By Balmer Neilly

FOR some reason or other, Mine Taxation has never been a popular subject for discussion in meetings of this kind, and it has never received the study and consideration its importance demanded. By way of explanation, two reasons may be suggested. In the first place, the computation, adjustment, and final payment of taxes, have been looked upon in most cases as a Head Office chore. Secondly, since taxes represent an uncontrollable cost item, they have been treated as an added rather than an inclusive factor in calculating unit costs. Perhaps because I am half Irish, and therefore resent taxation of all kinds, perhaps because I am half Scotch, and am therefore concerned with the results, I have always taken a keen interest in this subject. Moreover, by some peculiar set of circumstances, I have been a participating party in many, perhaps I can say most, of the discussions on this subject that have taken place between the Governments and the representatives of this industry during the past thirty years. Looking backward, certain very definite impressions remain. Political considerations have never had any part in these discussions. Views have been exchanged upon the frankest possible basis, and, when we disagreed on some particular detail, we agreed to disagree, and followed through in harmony and? good faith. We, as an industry, have refrained from importuning and fault finding in ways that might be considered as petty or selfish, and it is only upon occasions such as this, where conditions necessitate action, that we lay our troubles before the powers that be. The Ontario Mining Tax Act was drafted by men who were earnest and practical as to purpose, and that Act has stood the test of time. It is, in. truth, a mode! Act, for it has been copied in its general clauses by both Quebec and the Dominion of Canada. We all know that, when a machine is running smoothly, we should leave it alone. The same is true of a well designed, easily applicable, taxation measure, and our present difficulty with respect to this Act arises out of an amendment made in 1916. In that year, you will remember, the Dominion imposed a wartime Income Tax Act. It was described as a wartime necessity and it was intimated t:1 at with the end of hostilities its application would be restricted and finally cancelled. The rate of taxation was modest, and when the Ontario Government was asked that the Dominion Income Tax be allowed as a deductible item, they readily acquiesced. This was looked upon as a temporary arrangement.

Jan 1, 1943

By Bergh. L. C.

On line monitoring and diagnosis systems of process operating performance are becoming an important part of industrial programs, leading to improve process operation and therefore product quality over time. In processes, such as the contact section of a sulphuric acid plant, a large number of input variables, highly correlated, are presented. These characteristics usually pose more difficulties in modelling the process for monitoring and diagnosis purposes. Multivariate statistical projection methods, such as Main Component Analysis, have been proposed to effectively deal with these situations. The application of these ideas to a section of a 2350 MTD sulphuric acid plant, located at the Caletones Smelter, including dry tower, gas blowers, catalytic reactor and S03 absorber processes, is discussed here. A PCA model with eight main components is used for monitoring and diagnosis of more than seventy operating variables. Hottelling's T2 and Q residuals test were used for detecting measurement problems in relevant variables, and for identifying which set of variables were responsible for driving the process outside its normal operating region. Furthermore, considerable information for the correction of the tested operating problems was given by the use of these techniques.

Jan 1, 2007

By G. Q. Liu

"The application of oxygen-enriched cyanidation to three Canadian gold ore samples has been investigated. The results showed that the use of oxygen can improve gold dissolution kinetics, reduce grinding time, and lower cyanide and lime consumptions. To obtain the same gold extraction, the required cyanide leaching time was reduced from 48 hours in slurry containing 8 ppm O2 to 12 - 24 hours in 20 ppm O2 slurry. Reagent consumptions were reduced by 23 - 37% for cyanide and by 35 - 54% for lime. There was little advantage to further increasing the dissolved oxygen to 32 ppm from 20 ppm. Gold extraction from the +200 mesh fraction improved 4 - 14% in oxygen-enriched slurry. A general kinetic model derived from the cyanidation of three ore samples can be described by the following equation: <equation>where E is the gold extraction (%) at time t (hours), EI is the ultimate gold extraction (%) , and &apos;P and k are constants depending on cyanide concentration, level of dissolved oxygen, and the characteristics of the ore samples. Comparative studies of conventional carbon adsorption and carbon adsorption in oxygen-enriched slurry have also demonstrated that oxygen enrichment resulted in more favourable conditions for gold adsorption."

Jan 1, 1995

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012