Search Documents

By Liang Zhen, Jian-Tang Jiang, Guo-Ai Li, Xiao-Ya Wang

"Deformation behavior of 2A97 aluminum alloy containing coarse secondary phases was studied using uniaxial hot compression (HC, 340–490°C, 0.4001–1 s-1). The flow stress could be described by a Zener-Hollomon parameter in hyperbolic sine function with the hot deformation activation energy of 237 kJ/mol. Based on the experimental data and dynamic materials model, processing maps were generated to demonstrate the hot workability of the alloy. The coarse secondary phases experienced dissolution by varying degree under different deformation temperature, which producing different effects on the microstructure evolution. When deformed at relatively low temperatures, a mass of fine grains shaped up in the original grains and grain boundaries, and the dominating deformation mechanism was believed to be dynamic recrystallization. As the deformation temperature rising to 490°C, most secondary phases disappeared and few recrystallized grains were observed, indicating that the secondary phases dissolved sufficiently along with dynamic recovery occurred during the hot deformation. Particle stimulated nucleation related to the coarse secondary phases was believed to promote the recrystallization and the recrystallization behavior was sensitive to deformation temperature.INTRODUCTION Al-Li alloys has received much attention as new promising structural materials in the aircraft and aerospace industries, due to their lower density, higher elastic modulus and improved fatigue crack growth resistance in comparison with the conventional commercial aluminum alloys (Ou Ling, 2015). 2A97 alloy is one of the 3rd generation Al-Li alloys targeting at comprehensive improvement of aviation aluminum alloy and applications for wing spars and ribs to other internal structures for transport aircraft. Al-Li alloys are usually formed by hot deformation, either by rolling or extruding. The deformation behavior and resulted microstructure evolution during the forming process mainly dominates the formability of the alloy and the serving performances as well. Therefore, the deformation behavior and microstructure evolution at elevated temperature need be made clear for optimizing the hot processing parameters and controlling microstructure evolution."

Jan 1, 2018

By F. E. Millett

The following notes deal chiefly with changes from steam to electric drives, or, in the case of the Bellevue pumps, from air to electric. Where electric power can be purchased or generated cheaply it can be used to advantage and is generally more economical than steam, especially in places remote from the central power-plant. Nothing could be more simple than the operation of electrical gear. It does not require a competent engineer constantly on the alert, oiling and watching bearings, and maintenance is at a minimum. The ease with which the current is transmitted from its source to where it must do its work is one of its greatest advantages. Transmission losses are very low. Generally speaking, the smaller the plant the lower the loss and 90 per cent, and better, efficiency is easily attained. In and around Bellevue 2300-volt, three-phase, is the standard distributing pressure; our power requirements and the distances transmitted, for the present, do not require more than this. Most of the heavier motors are 2300-volt .machines, which eliminates the cost and possible troubles of step-down transformers, and makes for a cheaper and less bulky motor. This applies to two fan, two hoist, and two compressor motors, the smallest being 75 and the largest 520 horse power. The standard pressure on power lines to all inside pumps is 550 volts, and 220 volts is general for the the tipple. While 110 volts is used for house and office lighting service, it is not economical around and in the mine. No matter what kind of device is used to lock and protect the lamps, they are invariably missing.

Jan 1, 1926

By K. Ihara, T. Yamaguchi, K. Matsumoto

"Al-Fe alloy sheets having layers with different strain components were produced by unlubricated hot rolling and the recrystallization texture formation during annealing was investigated in each layer. In this study, the strain component introduced by rolling was quantitatively evaluated by measuring degree of bending of an aluminum pin embedded in the sheet. The textures before and after annealing were investigated by the SEM-EBSD technique. It was clarified that, in the middle layer, where comparatively small shear strain was introduced, ß-fiber subgrains and cube {001}<100> oriented subgrains were formed before annealing, and cube oriented recrystallized grains grew after annealing. On the other hand, in the surface layer, where large additional shear strain was introduced, shear texture components and cube oriented subgrains were formed before annealing, and shear texture was retained even after annealing, while cube oriented subgrains did not grow and were encroached. It was suggested that introduced strain components influenced the recrystallization texture formation by inducing different distribution of the subgrain size, stored strain energy and orientation relationship with surroundings before annealing.INTRODUCTION The microstructure developed during the hot-rolling process of aluminum and aluminum alloys affect the mechanical properties of the final product sheets. Especially, the crystallographic orientation in the final product sheets affects the r- value and ears during deep drawing (Humphreys & Hatherly, 2004), then the texture control in the hot-rolling process is important. When the friction between the rolling roll and rolled sheet in the hot-rolling is large, both the rolling texture and recrystallization texture tend to be heterogeneous in the thickness direction. It is known in many rolled aluminum alloy sheets that the texture in the surface layer was different from that in the middle layer because of additional shear strain. It was reported that in the vicinity of the surface layer, where large additional shear strain was introduced, the shear texture <1 1 1>//ND and < 1 1 0> // RD which contain components of {1 1 1} <1 1 0> and {0 0 1} <1 1 0> developed during rolling, and the shear texture developed even after recrystallization annealing (Sakai et al., 2002). Particularly, it is thought that the <1 1 1> // ND texture contributes to improve the r-value and press formability (Inoue & Takasugi, 2007). Therefore, asymmetrical rolling and high friction rolling have been applied to improve formability of aluminum alloys by adding shear strain in the rolled sheets as deep as possible (Kamijo et al., 1972; Inoue et al., 2005). However, few researches have been focused on the microstructures and texture before annealing and thus, the detailed mechanism is still unclear how the texture after annealing is affected by the texture before annealing. In this study, the Al-Fe alloy of commercially pure aluminum was chosen as the first material to be studied in order to clarify the fundamental process of the recrystallization texture formation. The main purpose of this study is to clarify the effect of additional shear strain on the rolling and recrystallization textures in the hot-rolled sheets by analyzing the transition of microstructure and orientation distribution through recrystallization annealing."

Jan 1, 2018

By M. H. Allan

"This paper presents the geographic and geological setting of Saskatchewan Power Corporation&apos;s Poplar River Mine in south-central Saskatchewan, about 8 miles from the U.S. border. Generally the mine, which is being expanded to four million tons per year, is in an extremely disturbed geological area with severe dewatering problems. The lignite coal, which is strip mined, is supplied directly to an electric power generating station by means of a 7-mile unit-train private railroad.A number of unique reclamation and socio-economic problems were encountered because of the proximity to the U.S. border and because of the lack of experience of the regulatory authorities in projects of this kind. These are described in some detail, as well as the performance of one of the largest draglines in Canada. IntroductionThe Saskatchewan Power Corporation is a publicly owned utility which has the franchise to supply electricity and natural gas to all customers within the boundaries of Saskatchewan.Saskatchewan is a province which can almost be divided in two: the populated southern portion, principally devoted to farming, and the northern portion which is mostly on the Precambrian Shield and consists of lakes, rocks and muskeg. This portion is largely uninhabited except for a number of small villages. However, in the last few years there has been considerable mineral exploration and development, notably for uranium. This has helped considerably in the diversification of the basic agricultural economy of the province.Saskatchewan consists of 251,700 square miles, 761 miles north to south and an average of 335 miles east to west. It has a population of approximately 960,000, giving a population density of four persons per square mile. The Saskatchewan Power Corporation supplies 357,249 electrical arid 221,378 natural gas customers."

Jan 1, 1982

By C. Dragusanu, J. Sims, J. Connolly

Based on a statistical analysis of the categorical and numerical data from the established geological model, a geochemical classification of mineralization has been shown to be objective in nature and correlated to the envisioned metal extraction process. Multivariate chemical classification has the potential to discriminate within a combined response from different types of alteration and metal abundances. Distinct domains of chemical response determined by clustering analysis were used as a validating criterion for a geologically driven metallurgical testing program. The groups established are spatially linked to the geological process responsible for their genesis, providing clarity in geometallurgical and resource modeling.

Jan 1, 2011

By Jacques Nantel

"The molybdenite property of Brynnor Mines Limited, Boss Mountain Division (wholly-owned subsidiary of Noranda Mines Limited), is situated approximately 360 miles northeast of Vancouver on the east slope of Takom-kane mountain in British Columbia's Cariboo District. Orebodies at the deposit fall into two categories; quartz breccia, and veins and stringers. The development of the breccia ore zone was started in June, 1964. The bulk of the ore is being mined from the stringer ore zone. The ore-body has been divided into 100-foot stopes and pillars. A sub-level blasthole method is used and the broken ore is handled in drawpoints and scram drifts. The development, drilling, blasting and handling of the ore are reviewed. The future pillar recovery operation is also analysed. The paper is also concerned with a scheduled shaft sinking program."

Jan 1, 1970

By M. Clotilde Apua, A. F. Mulaba-Bafubiandi

"The efficiency of hydrochloric acid (HCl) leaching of gold from low grade gold-bearing material has been investigated in the presence of sodium hypochlorite (NaOCl) to produce in situ chlorine gas which is an oxidizing agent able to oxidize gold metal to its soluble forms. The effect of concentrations of HCl, NaOCl, and mixtures of HCl + NaOCl was sought. Iron and potassium present in the feed were leached and consumed all the HCl. Gold found as inclusion in pyrite was not exposed to the lixiviant. Therefore, leaching of gold from low grade gold-bearing material in aqueous chlorine solution is not an effective process for now.INTRODUCTIONHydrometallurgy of gold is commonly based on cyanide leaching solution. Due to the environmental concerns related to cyanidation and mercury processes, and inefficiency of cyanide gold leaching to dissolve refractory ores, sustainable alternative lixiviant systems, capable of generating gold (I) and gold (III) complexes must be studied. Amongst non-cyanide gold lixiviants there is the chloride/chlorine system (Hilson and Monhemius, 2006; Senanayake, 2004; Pilsniak and Trochimczuck, 2007; Wang et al., 2007; Reeves et al., 1999; Khodadad et al., 2008).In practice, the most oxidizing agents utilized for the leaching of gold as chloride, are chlorine (Cl2) or hypochlorite (HOCl) which are either generated in situ by suitable reaction or added in solution (Adamson, 1972). The dissolution of gold concentrate using hydrochloric acid, sodium chloride and sodium hypochlorite (Cl-/HOCl system) were studied (Puvada and Murthy, 2006). The effect of NaOCl and NaCl concentrations were also investigated. The leaching was performed under the following conditions; time: 4h, solid–liquid ratio = 1:4, at room temperature. It was found that the increase of the NaOCl concentration from 25 to 75 g/L did not have any meaningful effect on the recovery of gold which was about 30% (experimental conditions; S/L ratio = 1:4, NaCl concentration: 25 g/L, HCl concentration: 0.35 M). It was also found that from 25 g/L to 200 g/L NaCl, the recovery of gold rose from 30% to 40% (experimental conditions; S/L ratio: 1:4, NaOCl concentration: 25 g/L, HCl concentration: 0.35 M)."

Jan 1, 2012

By Y. Buro

The Bachelor Lake gold deposit occupies an ESE-trending, SW-dipping, silicified shear zone with hematitic alteration. It transects NE-trending, steeply dipping Archean volcanic formations and the O'Brien granite. Major W-SW and N- NE-trending faults have affected the ore zone and the emplacement of the granite intrusions. Movements along the WSW set may have opened the fractures filled by the mineralization. Gold is generally associated with pyrite. Its source, whether a granitic pluton or a volcanic sequence, is undetermined, but the granite probably provided the concentrating mechanisms through heat and hydrothermal solutions.

Jan 1, 1984

By Ken Wood, Luc Duval

"The development and operation of the milling circuits treating the different Selbaie orebodies are discussed in this paper. The project is reviewed from metallurgical evaluation through construction to present operating status. The current flowsheets are described, with discussion of some unusual features.IntroductionThe Selbaie concentrator commenced initial production in August 1981, treating underground B zone copper ore in a single 1500 t/d circuit. Throughput was increased to 1650 t/d in 1985. The mill was expanded in 1986 to treat ore from the A-I zone open pit; an independent circuit was added to selectively treat 5000 t/d of copper-zinc ore. Current total mill throughput through both circuits averages 7200 t/d with the production of approximately 270 t/d of copper concentrate and 230 t/d of zinc concentrate.This paper describes the stages involved in bringing the project from initial laboratory testing to its current status as one of the most important producers of silver, copper and zinc in Quebec and a major employer in the region."

Jan 1, 1990

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019

By D. Laguitton

The basic chemistry of a1•senic related to its dissolution and subsequent precipitation in gold-mine waste waters is discussed. The lime addition methods provides the most economic treatment of arsenical slurries, but requires a careful control of the oxidation of Asm into Asv, of the pH (>12) and the filtration of the precipitate. If arsenic levels below 0.5 mg/ l are required, a modification of the method by phosphate addition must be considered.

Jan 1, 1976

By G. Roy, D. R. Lentz, A. O. Wills

"Abstract - Diamond-drill hole DDH-B357, located 1.5 km north of the Brunswick No. 6 Zn-Pb- Cu-Ag volcanic-sediment-hosted massive sulfide (VSHMS) deposit, intersects three exhalative horizons within variably altered felsic volcanic rocks of the Nepisiguit Falls and Flat Landing Brook formations. These three petrographically indistinguishable iron formation intervals (Fe2O3T = 21.4 wt.%) likely represent cogenetic hydrothermal sedimentary units because they display a common geochemical signature: Fe2O3T = 42.9 ± 10.5 wt.%, MnO = 5.4 ± 3.1 wt.%, elevated base metal values (Zn+Pb = 1999 ± 1091 ppm), strong enrichment in additional exhalative components (CaO = 5.3 ± 3.9 wt.%; P2O5 = 1.43 ± 1.00 wt.%), oxidized signature (Fe/Mn = 10 ± 6), as well as a common immobile element signature (Zr/TiO2 = 0.025 ± 0.007) representative of a pelagic source. The calc-alkaline to transitional host volcanic rocks can be discriminated by Zr/TiO2, and to a lesser extent by Th/Nb: Nepisiguit Falls Formation: Zr/TiO2 = 0.053 ± 0.004, Th/Nb = 1.08 ± 0.37; Flat Landing Brook Formation: Zr/TiO2 = 0.107 ± 0.043, Th/Nb = 0.86 ± 0.17. A symmetrical repetition of the footwall-iron formation-hanging wall stratigraphic sequence is observed in DDH-B357, with distinct felsic volcanic rock domains separated by the three iron formations. This is best explained by parasitic F2 folds on the west flank of the south-plunging Brunswick antiform, similar to the fold closures known to host massive sulfide accumulations in the Brunswick No. 6 and No. 12 mines. Iron formation geochemistry and felsic volcanic rock chemostratigraphy from drill core sampling can provide an effective mineral exploration tool for the structurally complex rocks of the Bathurst Mining Camp. Sommaire - Le forage au diamant DDH-B357, situé à 1.5 km au nord du gisement de Sulfures Massifs à Encaissant Volcanique et Sédimentaire (SMEVS) de Zn-Pb-Cu-Ag Brunswick No. 6 recoupe trois horizons exhalatifs au sein des roches volcaniques felsiques diversement altérées des formations de Nepisiguit Falls et de Flat Landing Brook. Ces trois intervalles de formation de fer, impossibles à distinguer pétrographiquement les uns des autres, représentent vraisemblablement des unités sédimentaires hydrothermales cogénétiques sur la base de leur signature géochimique commune: Fe2O3T = 42.9 ± 10.5 % poids, MnO = 5.4 ± 3.1 % poids, des teneurs élevées en métaux usuels (Zn+Pb = 1999 ± 1091 ppm), un fort enrichissement en composantes exhalatives additionnelles (CaO = 5.3 ± 3.9 % poids; P2O5 = 1.43 ± 1.00 % poids), une signature oxydée (Fe/ Mn = 10 ± 6), ainsi qu’une signature d’éléments immobiles communs (Zr/TiO2 = 0.025 ± 0.007) indicative d’une source pélagique. Les roches volcaniques encaissantes calco-alcalines à transitionnelles peuvent êtres reconnues par leur rapport Zr/TiO2, et à un moindre degré par leur rapport Th/Nb: Formation de Nepisiguit Falls: Zr/TiO2 = 0.053 ± 0.004, Th/Nb = 1.08 ± 0.37; Formation de Flat Landing Brook: Zr/TiO2 = 0.107 ± 0.043, Th/Nb = 0.86 ± 0.17. Une répétition symétrique de la séquence stratigraphique Mur-Formation de Fer-Toit a été observée dans le forage DDH-B357, avec des domaines distincts constitués de roches volcaniques felsiques séparés par les trois formations de fer. La meilleure explication est que le flanc ouest de l’anticlinal Brunswick à plongée sud est affecté par des plis parasites F2, similaires aux zones de charnière contenant les sulfures massifs des mines Brunswick No. 6 et No. 12. La géochimie des formations de fer et la chimiostratigraphie des roches volcaniques felsiques en forage peuvent fournir un outil d’exploration minérale efficace dans les roches structuralement complexes du Camp Minier de Bathurst."

Jan 1, 2006

By Ernest Becker

Golder Associates provided overall radiological direction and assistance to the client in their interactions with the Canadian Nuclear Safety Commission and operational radiation protection services for the remediation of a calciner that had been used to process uranium. The project was somewhat unusual in that the radioactivity from within the calciner room was removed from the site and the cleaned steel recycled. The presence of yellowcake within the process equipment required stringent radiation protection measures. This project was completed successfully with minimal radiation exposures to the workers and the effective protection of the environment.

Aug 1, 2010

By J. E. Dodge

Tasu, currently an open-pit operation, services the primary crusher from two areas by ore-pass raises. The problems encountered and advantages gained are discussed. Mine equipment and operating practices are covered, together with blasting practices, line drilling and the pre-shearing necessary to stahilize the pit walls.

Jan 1, 1968

By R. B. Fermor

"The tyndalloscope is used in Europe for dust-hazard assessments in both coal and metal mines. Dust-hazard conditions can be directly evaluated by the tyndalloscope in many underground working situations, once the basic standard table or tables have been prepared from representative mine-rock samples.The tyndalloscope is excellent, in many cases, for diagnostic dust sampling during a working shift, because individual readings can be taken to within three-minute intervals. The limitations of the tyndalloscope are also discussed.The author suggests that a combination of both the tyndalloscope and gravimetric sampling methods would be an ideal match for most mine dust-hazard assessments."

Jan 1, 1970

By R. Bruce Graham

The formation, evolution and classification of peat bogs is discussed. Factors resulting in the internal and external morphological changes in a bog are described. The fibrous, absorptive and sterile properties of peat moss account for its widespread use in horticulture and related fields. These properties also account for its usefulness as a binder in pelletizing, as an insulating material in bat tons and in panel construction. Peat, the humijied product of peat moss is used in market gardening and sod growing. It is utilized in Europe as fuel. It is a source of activated carbon and gas. Potentially peat can be used to produce waxes, resins, tannins, cellulose, hemicellu/ ose, humic acids, lignin and hymatomelanic acid. At present other cheaper sources are available.

Jan 1, 1984

By E A. Mitchell

In the fall of 1961, Cominco dis-carded its long-established system of feeding the lead blast furnaces by narrow-gauge tram and V-cars, and installed an elevated monorail bucket system. This system automatically loads buckets of sinter, along with the correct proportion of coke, and delivers them to any of several designated furnaces. Direct labour usage has been reduced by nine men per day; improved coke proportioning has been achieved; and a major safety hazard has been eliminated. Introduction I N THE fall months of l 961. the system of feeding the lead blast furnaces at the Trail, B.C., smelter of The Consolidated Mining and Smelting Company of Canada Limited was altered from the tradition-al narrow-gauge railway and V-car method to one employing mono-rail carriers. The change was in keeping with a recent trend at Trail to replace narrow-gauge tramming with alternative methods of materials handling. In the case of the blast furnace feeding, the

Jan 1, 1963

By E. Gaucher, M. St-Amant

"Among the electromagnetic surveys performed by SOQUEM in the last three years, a certain number of the more instructive cases have been chosen to illustrate the theory of electromagnetism by field examples of: (a) The depth penetration of the TURAM as compared to the SLINGRAM (Ronka) method. (b) The limitations of the TURAM as compared to the SLINGRAM method when a conductor dips the wrong way, or when it is small in size. (c) The expression of a shallow-dipping conductor in a SLINGRAM survey. (d) The effect on the SLINGRAM survey of deep ditches or reef structures.(e) A comparison between the CRONE and the SLING-RAM method in the Abitibi clay belt, by means of field and model studies, indicating a usually better signal-to-noise ratio for the SLINGRAM method. From the above and from other experiments, different electromagnetic methods are now being used by SOQUEM, depending on field conditions."

Jan 1, 1970

By D. C. Rance

"The Quintette Coal Limited property is located in the northeast coal area of British Columbia.A basic agreement with the Japanese steel industry was executed on January 27, 1981 for the sale of 69.5 million tonnes of Quintette metallurgical coal over a 14.5-year period. This contract period can be extended by five years by mutual agreement. Sale agreements have also been signed for the sale of 19.4 million tonnes of oxidized coal over a 15-year period.Work started on site development in the late summer of 1981, and at present, two of the four eventual pits-the McConkey and Frame-are under development.The pits are currently in a prestripping phase. These pits are notable for the stripping volumes that have to be removed from relatively small pit areas. In order to provide for the required detailed rapid short-range planning of these pits, engineering will be computerized, as will the truck dispatch system.The mining area lies 21.1 km from the plant site by road and the transport of raw coal to the plant is by means of a high-speed conveyor system which has a total length of 13.4 km with a vertical drop of 740 m.The surface plant facility was designed on a modularized basis to facilitate maintenance, and is designed to enable the use of gravity f low of raw coal and heavy media in the plant to minimize the use of pumps.The construction of the plant and mine site facilities is ongoing, and the first coal production is scheduled for early December 1983.IntroductionQuintett e Coal Limited is a Canadian company incorporated in the province of British Columbia in 1971. Denison Mine s Limited is the manager of Quintette&apos;s activities. Equity in Quintette Coal Limited is held by several shareholders, with interests as follows: Denison Mines Limited, 50%; Charbonnages de France International S.A., 12%; and Japanese interest, 38%."

Jan 1, 1983

By N. E. Izatt

Molecular recognition technology (MRT) has a wide range of applications in the hydrometallurgical and chemical processing industries for the selective removal of iron as well as various other impurities from a variety of streams, including aqueous solutions through a wide pH range, as well as organic solutions. An example of a commercial application is provided for the removal of iron from an aluminum chlorohydrate stream. In this example, MRT has a selectivity for iron relative to aluminum which is significantly higher than that of ion exchange resins. A discussion of MRT capabilities for other impurities and streams is also provided.

Jan 1, 2006