Search Documents

By Nessetech Consulting, L. A. Cisternas, E. D. Galvez, S. H. Kuan, L. H. Saw

"In Malaysia, there were two rare earths processing plants namely Asian Rare Earth (ARE) and the Malaysian Rare Earth Corporation Plant (MAREC) in Perak, which were operated until 1992 and were subsequently closed due to problems pertaining to disposal of large amount of radioactive waste. Recently, Lynas Advanced Materials Plant (LAMP) has become one of the largest rare earths processing plant in the world producing rare earth elements (REE) in Gebeng, Pahang. The primary raw material is lanthanide concentrate (LC) which is imported from Mount Weld mine in Australia and shipped to Malaysia. LC is produced from lanthanide ore after mining and mineral processing. The ore has a lower impact than Bayan Obo, Mountain Pass and adsorbed clay deposits, given the small footprint of the mine itself and the remoteness of the location. The type of ore being mined (rare earth phosphates: carbonatite, monazite) may have higher thorium content than bastnasite ore from the Chinese or American mines but still far below radiation concerns. This paper was written to review the processing flowsheet at the Lynas Advanced Materials Plant (LAMP), the environmental impact associated with the processing of the said ores and the sustainability of the operation.INTRODUCTIONRare earth minerals are one of a set of 17 minerals or chemical elements which consists of yttrium and scandium, as well as the 15 lanthanide elements (lanthanum, cerium, praseodymium, neodymium, promethium, europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium, and lutetium). Despite their importance, rare earth minerals rarely exist in economically viable concentrations and they are usually difficult to extract. Rare-earth minerals create strong magnets when added to magnetic elements such as iron, and are useful for the production of electronics systems as well as electric cars. They are also used extensively in automotive catalytic converters, fluid cracking catalysts in petroleum refining, wind turbines, phosphors in colour televisions and flat panel screens, displays for mobile phones and laptops, rechargeable batteries, and various medical devices. The elements are typically split into two subgroups: the cerium sub-group of ‘‘Light’’ rare earth elements (LREEs) which includes La to Eu and the yttrium sub-group of ‘‘Heavy’’ rare earth elements (HREEs) which include the remaining lanthanide elements, Gd to Lu, including yttrium (Gupta and Krishnamurthy, 1992; Jordens et al., 2013; Trifonov, 1963). Scandium, however, when it is classified as a rare earth element, is not included in either the LREE or HREE classifications (Gupta and Krishnamurthy, 1992; Jordens et al, 2013). Half of the world’s 110 million tons of reserves exist in China while other sizable deposits are found in Russia, United States, Brazil, India, Australia, Canada, and Greenland. The countries known to be actively mining REE are China, Russia, India, Brazil and Malaysia (Hao et al., 2015). Among these countries, China has the largest REE production, accounting for more than 93% of global supply (Yap, 2015). The critical metal report (Moss et al. 2011) listed 14 economically vital raw materials that are prone to supply disruption and concluded that supply disruption would threaten the goal for cleaner transport and sustainable energy since rare earth metals are used in products using green technology, such as hybrid/electric vehicles, carbon capture systems, wind power generation, low-energy lighting, and energy efficient flat-screen displays."

Jan 1, 2016

By Xiaozhu Chen, Qi Ping, Pu Yuan, Qinyong Ma

"In order to investigate the fractal feature of coalmine deep rock fragments under impact loads, variable cross-section split Hopkinson pressure bar apparatus, 50 mm in diameter, was adopted to conduct impact compressive test for rock specimens from -962m deep coalmine. Various impact pressures, such as 0.3, 0.6, 0.9 and 1.2MPa, were selected to implement different loading rates. Sieving statistical analyses were conducted for rock fragments after being impacted, and the particle size distribution of broken rock in various loading rates were calculated with the fractal method and then the corresponding fractal dimension was obtained. Test results shows that there is a good self-similarity and fractal feature in fragments distribution of deep coalmine sandstone under impact loads. The fractal dimension of fragments is between 1.9 and 2.7. The research also indicates that there is an approximate power relationship between dynamic compressive strength and fractal dimension, and a strength power relationship between fractal dimension and average strain rate. Moreover, there is a linear relationship between fractal dimension and specimen absorbed energy. The rock fractured process can be quantitatively described through fractal dimension, which can reflect the deep rock broken degree and is an ideal index to evaluate the distribution of rock fragments.INTRODUCTIONBroken rock is one of the most basic processes in mining operations, rock fragmentation has always been an important index to evaluate rock breaking effect (Xu & Yu, 1984). Macroscopic fragmentation of rock material is the final results of continuous development, expansion, gathering and cutthrough of internal micro-cracks. This process, developing from microscopic damage to macroscopic fragmentation, is an energy dissipation process and shows fractal characteristics (Xie, 1993). Turcotte (1986) has conducted statistical analyses of fragmentation for different kinds of geological materials under various broken conditions, and arrived at the conclusion that fragmentation distribution is a fractal."

Jan 1, 2015

By J-F. Turgeon, Y. Pépin, G. Hudon

The high temperature hydrochloric acid leaching of titanium slag in the QIT upgraded slag process (UGS) creates a harsh environment for materials of construction. Because of their excellent chemical and heat resistance, furan mortars are a key component in the lining system of the UGS pressure leach reactors. Similar products coming from different manufacturers have however shown unequal performances in service. In some cases, cracking of the brick lining has occurred during curing of the mortar. This study was initiated to investigate the impact of the curing conditions on the properties of carbon filled furan mortars. Laboratory tests were conducted to assess the effects of temperature and exposure to water and HCl solutions on mortar shrinkage and mechanical properties (tensile, compressive and bond strength). Three commercial furan mortars that have been used in the UGS leach reactors were thus characterized. Mortar properties were found to vary significantly among the products tested. Moreover, the curing conditions were shown to have a significant impact on mortar shrinkage and mechanical strength. The experimental findings provide explanations for the unequal performances of the mortars in service and for the problems of brick lining cracking that occurred in the UGS leach reactors. This study demonstrates that excessive mortar shrinkage compromises the integrity of a brick lining system.

Jan 1, 2004

By F. T. Rabbitts

Introduction When the investigation of radioactive ores began at the Mines Branch about five years ago it was at once evident that improved chemical methods for the determination of uranium were essential. The published methods available were time-consuming and insensitive and were lacking in accuracy and precision. It was desirable to obtain methods which would be rapid, sensitive, and accurate. They should also allow for the possible presence of any interfering elements and should be adaptable to routine analysis by technicians. Chemical methods are necessary to provide standard analysed samples for counting and to check analyses by counter methods. Moreover, counter methods cannot be used, and only chemical methods are suitable, when the sample is not in equilibrium, as with weathered minerals and leach residues. As leaching processes are improved, more sensitive chemical methods are required for the increasingly lower content of uranium in the leached residues. When the leaching process reaches the plant stage, speed of analysis becomes more important, without sacrificing accuracy. The purpose of this paper is to describe briefly .the methods used at the Mines Branch for the chemical analysis of uranium in ores. These methods represent the results of investigations by a number of groups in the United Kingdom, the United States, and Canada.

Jan 1, 1952

By M. S. Moats, C. M. Campbell

Samples of a high impurity (90.05 wt. % Cu, 4076 ppm Pb, 1939 ppm As and 635 ppm Bi) commercial copper anode were characterized and then electrorefined in a laboratory scale cell. Anode inclusions were examined using backscatter mode scanning electron microscopy and energy dispersive spectroscopy. Hundreds of inclusions were measured for size, morphology and composition. Commonly found inclusions were copper oxide (Cu2O), complex oxides (Cu-Pb-Bi-As-O) and copper selenides/tellurides. The weight percent of lead and arsenic increased with increasing inclusion size up to 4- 5 microns. During electrorefining, starter sheet ductility was negatively impacted by thiourea addition. The importance of arsenic (V) concentration on the electrolyte concentration of bismuth was observed. INTRODUCTION Copper electrorefining is a commercial process used to produce the majority of the world’s refined copper. During this process, impure copper anodes are dissolved electrolytically, and high purity copper is deposited on cathodes. As the anodes dissolve, the impurities either accumulate in the electrolyte or report to solids that form on anodes surfaces or at the bottom of the refining cell. These solids are called slimes. Slimes contain precious metals and are collected for further processing. Slimes are also an important outlet for problem impurities such as lead, antimony and bismuth. The electrorefining process is operated in such a way to encourage the deportment of these elements to the slimes. Impurities in copper anodes have been studied extensively by Chen and Dutrizac (1990, 1993 and 2005). The most common impurities found in modern copper anodes include: Ag, As, Au, Bi, Fe, Ni, O, Pb, Sb, Se, Sn and Te. Impure copper anodes are produced by pyrometallurgical methods and have purities ranging from 97.7–99.7% Cu (Moats et al., 2019). The composition ranges of commercial copper anodes from the 2019 worldwide tankhouse survey are given in Table 1. The concentrations of anode impurities vary widely dependent on the source material and prior processing steps. Based on the work of Chen and Dutrizac, both gold and silver are predominantly found in solid solution within the copper grains while a minor amount of Ag can be found in Cu2(Se/Te) inclusions. Nickel is entirely soluble within the copper grains up to anode compositions of 2500–3000 ppm Ni; above which NiO and kupferglimmer phases are formed (Chen & Dutrizac, 1990). As, Bi, Pb and Sb are found in solid solution within copper and within oxide inclusions typically found along grain boundaries. Oxides are formed due to the presence of 0.13-0.18 wt. % O (Chen & Dutrizac, 1990). This is because during solidification of the cast anodes, impurities are enriched in the liquid phase as the copper grains nucleate and grow. The inclusions form from the last liquid to freeze, which is typically along grain boundaries (Wenzl & Filzwieser, 2007; Wenzl, Filzwieser, Mori & Pesl, 2008).

Jan 1, 2019

By J. Makgatho, P. Condori, J. Winnett, Fischerm D.

"Palabora Mining Copper (PMC) has two autogenous mills that have been in operation since 1976. The mills were originally designed to treat 30 000 t/d of open cast copper ore in a closed circuit with cyclones. As the ore body went deeper the open cast method of mining was changed to block caving, a consequence of this was the dolerite content (hardest barren material) increased significantly, increasing the production rate of pebbles and thus reducing the milling capacity. In order to cope with the increased ore hardness and to increase mill capacity, a second ball milling stage and pebble crushing were incorporated to the circuit. The above actions created new challenges to the circuit operation and bottlenecks in different areas of the milling circuit.This paper reports the holistic work performed on the Palabora autogenous milling circuit including the implementation of a mill constraint control scheme, the implementation of a pebble removal system from the circuit and a new circuit configuration."

Jan 1, 2012

By C. Edwards

ABSTRACT: Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. During that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb (299,370,964 kg) of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin conclude the paper.

Jan 1, 2012

By V. C. Pandolfelli, L. Paulino, C. E. Zangiacomi

The continuous improvement in aluminum industry over the last years has increased metal output at lower cost. The potlining plays an important role in this regard due to high cost involved and more recently in its environmental aspects. In order to increase potlife and thus minimize the aluminum cash cost, a systemic approach is needed, through investigating the main cathode failure mechanisms by using a pot autopsy as a powerful tool, and then making the necessary chances to achieve extended potlife. In addition, preheating and pot start-up may also damage the cathode if not performed with an appropriate technique or even if the lining materials are not specified correctly, among other factors. All these aspects will be presented and discussed in this paper. Increased potlife, especially now that the current is reaching values up to 300kA, will allow aluminum plants to match their goals more efficiently at lower costs.

Jan 1, 2006

By J. W. Merks

"Simulation is the process of designing a computerized model, of a system or procedure, for the purpose of understanding its behaviour and developing strategies to control its operation. Simulation models are rapidly becoming an effective tool for mineral processing plants. Powerful software and fast hardware are more readily available than a basic understanding of the theory of mathematical probability and applied statistics that process simulation models demand.Simple spreadsheet software can be used to develop simulation models that take into account any set of conditions at a mineral processing plant. In addition to an unbiased estimate for each variable in the set on which two-and three-product formulas are based, reliable variance estimates for all variables are required. How to estimate variances, effectively and at the lowest possible cost, and how to compute variances for simple functions such as the metal content of a quantity of ore or concentrate, or more complex functions such as the percentage recovery at a mineral processing plant, are the key to useful simulation models.IntroductionSimulation models for systems and procedures have become one of the most powerful and effective applications for computers( 2.6). Simulations are applied to a wide range of scientific and engineering disciplines. Generally, a model is designed to investigate the effects of changes in and interactions between a set of variables before a system is in operation or a procedure is implemented, by simulating weeks, months, and even years of operation, in a few minutes of computer time. Along with practical and useful applications always comeabuse and misuse. For a simulation process cannot be more reliable than the methodology that was applied to design the model, to estimate variables and variances, to check performance, and to verify validity. A mineral processing plant is a dynamic system that changes continuously as a function of time but within probabilistic constraints that can be estimated by applying statistical tools and techniques to the variables and variances that interact in the system.A model should be designed to simulate not only the set of variables but also the variance for each variable. Models in which constant variances are used to generate normally distributed random numbers, are less realistic than models in which the variances are simulated first, and then used to simulate the variables."

Jan 1, 1991

By D. Shishin

Continuous integrated experimental and thermodynamic modelling work is conducted in Pyrometallurgy Innovation Center (PYROSEARCH). The target is to develop a tool, which is capable to predict the compositions of phases, phase equilibria and enthalpy balance for pyrometallugical processes with higher accuracy. All these can be achieved by thermodynamic calculations based on Gibbs energy minimization algorithm. Recent developments made it possible to predict important factors, such as the chemical solubility of Cu in slag as a function of matte grade, temperature, P(SO2), Fe/SiO2 ratio in slag, wt% Al2O3, CaO and MgO in slag. In industrial practice, it is not only chemical solubility, but the overall amount of slag, which affects the recovery of copper and other valuable metals. It will also impact the energy balance. The presence of solids in the slag matrix influences the physical entrainment of matte in slag. Oxygen enrichment which is sometimes used to control the temperature of the furnace, may also affect the volatilization of minor elements into the gas phase. Same is true if additional fuel is used to compensate for heat balance. In other words, all key process parameters mentioned above are interrelated. Present study demonstrates the ways thermodynamic modelling can be used to link those process parameters on the example of copper smelting. INTRODUCTION Research methodology involving integrated thermodynamic modelling and experimental approach has been recently reported by the authors (Shishin, Hayes, & Jak, 2018 Shishin, Hidayat, Jak, Decterov, & Belov, 2016). Present paper reviews the updates and discusses challenges in the development of a large self- consistent thermodynamic database. The database covers the Al-Ca-Cu-Fe-Mg-O-Pb-S-Si-Zn-(Ag, As, Au, Bi, Ni, Sb, Sn) chemical system. The database works in the environment of FactSage software Bale et al., 2016 and related family of products: ChemApp (Petersen & Hack, 2007), ChemSheet and SimuSage. A list of phases, and thermodynamic models is shown in Table 1. For the copper industry, most important phases are Gas, Slag, Spinel and Liquid matte/metal/speiss. Black-colored elements represent the base system, elements in green can be considered as slag modifiers (slagging elements), and elements in red are minor. Ni is highlighted because it was included recently, in 2019, and currently under development. In addition to copper, the database covers the conditions typical for lead and zinc pyrometallurgical extraction. It is developed in consistency with the experimental results for high concentrations of Pb and Zn. Examples of applications in the present study include the thermodynamic analysis of fluxing for an agitated copper reactor to show the effect of Fe/SiO2, and calculations of copper slag cleaning using reductant.

Jan 1, 2019

By L. Frost

Physical Conditions Great Britain The physical conditions in the mines investigated in Great Britain are similar to those found in the mines of the Dominion Steel and Coal Corporation, with the important difference that many of the coal seams visited were interspersed by a large number of heavy faults, making the development of a continuous face operation difficult, and in many cases the life of a unit development was exceptionally short, adding to unit cost; but in spite of these difficulties, a great deal has been accomplished in the application of mechanical loading units in a number of the mines in the areas visited. The coal-bearing measures, as in Nova Scotia, consist of shales and sandstones, and in some sections mussel bands overlie the coal seams making roof conditions difficult'. In several mines, the main roof consisted of weak shale bind, being held by a coal roof of varying thickness. This shale bind had a tendency to flow when the coal roof was broken. The floor, in some cases where cutter loaders were operated successfully, consisted of weak, flaky shales with very little resistance and a tendency to disintegrate into powder when broken. The depth of cover under which these mines were operating varied from 250 feet to 2,340 feet, with an average of 1,700 feet. The coal seams varied in height from 3 feet to 8 feet 6 inches, and the gradients from level to 33 per cent. The seams vary in hardness, but all-with the exception of one seam, the 'Morrison Busty'- presented a cutting problem similar to that found in Nova Scotia. The structure and cleavage of the coal was well defined and uniform. Some of the seams visited were gassy, ?but the temperature of the workings generally was not in excess of 70°F.

Jan 1, 1948

"Sedimented hydrothermal precipitates of silica, now fine-grained quartz, are described from a Pb-Zn-bearing vein system. Their discrimination from the wall-accreted fine-grained quartz that is common in the shallow parts of epithermal systems is discussed. Local fine-grained (<0.3 mm) quartz accumulations occur in a suite of veins with otherwise normal drusiform and crustified infills. This sediment may fill the vein above chokes in steep segments (axial plugs), or form continuous layers within the footwall material where the vein is inclined at low to moderate angles. Pads of fine-grained sediment are deposited on the upwards-facing surfaces of wall-rock clasts and of drusiform crystals growing from the vein walls. The asymmetry of these deposits differentiates them from the more common symmetrical, crustified walllining deposits of fine-grained quartz and opaline silica, and requires a gravity-controlled, sedimentary depositional mechanism.Thin section examination shows that much of the fine-grained quartz is present as elongate prisms. The prism habit was present soon after deposition, but it is not possible to identify unequivocally the original sedimented grains. Sedimentation of vein- and wall-rock-derived detritus is also recognized. Deposition of the fine-grained sediment accompanies normal in situ drusiform growth of quartz and other vein minerals. The mammilated and spherulitic textures associated with accretion of amorphous quartz are entirely absent from the Tyndrum veins with sedimented materials. The literature on modern hydrothermal waters and physical chemistry of silica precipitation shows that precipitates of silica suspended in hydrothermal fluids are amorphous and derived from colloidal silica. It is argued that much of the suspended silica was present as quartz at the time of deposition or was converted from amorphous silica almost immediately after deposition.Hydrothermal sediments and their distribution potentially provide information on flow directions and velocity in veins. Plugs of sediment obstruct vertical flow and lead to local flows with large horizontal components. It is shown that sedimentation features occur in other deposits and can involve other minerals. If the features seen here can be scaled up to the size of major veins, they may result in up and downdip variations in mineral assemblages and abundances, which may affect grade."

Jan 1, 2007

By Karen Munro

Importance of Aquatic Studies for Mining ?Aquatic habitat is usually the first area where a mine interacts with the ?real world? outside the mine footprint ?Water management is a key consideration for a mine?Effects on the aquatic environment often extend to wildlife and human uses ?There is a lot of regulatory focus on issues of water quality, fish and fish habitat

May 1, 2011

By David K. Fountain

"The growth of the mining industry in British Columbia in the last ten years has been largely the result of the development of large low-grade copper and molybdenum deposits. There are two problems which must be solved in the search for mineral deposits of this type. It is necessary to detect large volumes of rock containing a low percentage of total sulphide mineralization1 and, secondly, to get some idea of the economic significance of this mineralization. The standard geophysical exploration techniques available have a varying degree of application in the search for disseminated sulphide de-posits. The electrical methods, and the induced polarization method in particular, are the most successful direct methods, and magnetic methods have indirect application in most situations. This is illustrated by geo-physical survey results from several properties in British Columbia."

Jan 1, 1968

By Gabriel Voicu, Marc Bardoux, Ross Stevenson, Nuno Machado, Jean Lafrance

"Abstract - Paleoproterozoic gold is found in two different volcano-sedimentary sequences and intrusive bodies separated by 600 km within the Guiana Shield. The 2148 Ma St-Élie granite intruded volcanic-arc sequences of the Paramaca Group, whereas the 2096 Ma Omai stock penetrated backarc/ island-arc sequences of the Barama-Mazaruni Group. Positive ?Nd values suggest that both suites lack Archean crustal contaminants, which is consistent with an origin in an oceanic arc setting.The St-Élie deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented chiefly by pyrrhotite and pyrite. Biotite, calcite, and chlorite are the main gangue minerals. The alteration haloes at St-Élie feature a strong potassic zone, which is absent at Omai. The ore-controlling structures are ductile and the vein emplacement is related mainly to contemporaneous, high-angle ductile shear zones. The St-Élie deposit formed at temperatures >350°C. The stable isotopes values are compatible with a magmatic or metamorphic source.The Omai deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented mainly by pyrite. Ankerite, scheelite, albite, and chlorite are common gangue minerals. The vein emplacement is syn- to post-deformation and it is related mainly to brittle shear zones with low-angle, stockwork networks and breccia zones. The Omai deposit formed in a temperature range between 250°C and 170°C, much lower than the St-Élie deposit. The stable isotope values are compatible with mixing between deep-seated fluids of metamorphic or magmatic origin with surface- derived fluids.These differences between St-Élie and Omai are interpreted in terms of their depth of formation. Alteration patterns, structural elements, and paragenetic assemblages indicate that the gold at St-Élie was most probably emplaced at a mesozonal depth, whereas the Omai setting yields evidence for epizonal conditions."

Jan 1, 1999

By J. D. Corbett

The spatial coincidence of the seven anomalies is obvious, even though the self-potential is offset northward. Because the ratio, as an indicator of conductivity, is a relative estimate at best, concise interpretation is limited in almost every instance to the location of a conductor or conductor axis. When related to the initial phase of an exploration program, magnitudes and ratios similar to those obtained from any one of the methods described, would be sufficiently attractive to warrant further investigation. The compilation shown is an empirical comparison of actual field results and no emphasis has intentionally been placed on the relative merits of one method in respect to another. Too many additional factors, i.e., size, depth and conductivity of overburden, etc., that cannot unequivocally be answered, enter into such a comparison before a relative evaluation can be made.

Jan 1, 1961

By A Walker

The presence of high noise levels in many industries, together with the fact that countries are becoming increasingly concerned with the health of its citizens, has contributed to the importance of the problem of hearing loss. This problem has become the focus of scientific research, law and medicine, and the object of this thesis is to present the means whereby noise may be detected, with its resulting effects and possible means of control, in mining operations. 0BJECTIONABLE noise is a particularly prevalent by-product of the mining industry, and, al-though a dangerous noise level has been recognized, it is believed that at no time now, or in the future, will it be possible to enumerate a single over-all decibel figure at which hearing impairment will oc-cur. Individual susceptibility must be recognized in any study of occupational loss of hearing aimed at the setting of standards and criteria for industrial noise control.

Jan 1, 1963

By M. Leroux, J. A. Finch

"Sizing below 38 µm (400 mesh) is an increasing requirement in mill testing laboratories. The Cyclosizer is gaining wide acceptance in this role. A recent alternative is to use electro-formed sieves (micro-sieves), which are available with openings down to 5 µm. The advantage of micro-sieving is a cut size which is independent of mineral density, easier retention of the fi nest fraction and reduced purchase cost. A simple method of microsieving using an ultrasonic bath, which performs readily to 10 µm, is described.A systematic study of Cyclosizing and micro-sieving is reported for three samples; silica, copper oxide and a lead concentrate. Micro-sieving gave comparable results. Comparison with a standard sizing method, the Sedigraph 5000D, revealed misplaced material in each fraction by both methods. The range for micro-sieving was from 20% to 60% depending on the sieve and material; for the Cyclosizer it was a consistent 40-50% for all cones and all materials. The Cyclosizer can be sensitive to feed mass and particle size for dense materials. It is recommended that for minerals of specific gravity greater than 5, no more than 35 g of -38 µm be used.The disadvantage of micro-sieving is that it requires continuous operator attention and sieving time depends on sample mass. To fractionate 35 g-as used on the Cyclosizer and considered at reasonable mass for mill testing purposes-through 25-, 15- and 10-µm sieves requires about 80 minutes.IntroductionParticle size has a pronounced influence on mineral separation processes. Consequently, the measurement of particle size plays an important part in mill testing. By far the most common method is by screening. This, however, is usually limited to 38 µm (400 mesh) or occasionally 25 µm (500 mesh). Increasingly, mineral products are becoming finer than this limit and consequently finer sizing methods are required."

Jan 1, 1982

By Yi-Chun Lin

Mechanical/Electrical/Piping (MEP) systems, due to their complexity and diversity, are the most intricate part of building construction. This being the case, Combined Services Drawings (CSD) and Structure, Electric and Mechanic(SEM) drawings can ensure that all coordination issues are resolved prior to construction. Construction companies attempt to apply Building Information Modeling (BIM) to manage and integrate engineering information and solutions efficiently into the CSD and SEM processes to enhance the accuracy of design and the efficiency of review. There are several powerful commercial tools, such as Bentley Navigator, Autodesk Navisworks, and Tekla BIMsight, that can review the integrated BIM model and detect conflicts in systems, and allow planners to correct the conflict issues one at a time. However, for increasing numbers of conflicts, this may be inefficient, and requires them to be arranged in a list according to impact and seriousness before solving them. For this reason, this research implements a module for conflict impact assessment based on rule-based reasoning to classify and weigh conflict impact and seriousness, and highlight the conflicted objects in the BIM system in different colors depending on their conflict type and seriousness during the analysis. This system not only detects and lists possible conflicts and errors, but also sorts them according to the severity of impact and conflict type. Planners can effectively modify the BIM models according to these conflicts as they are listed and visualized in the BIM system. If these conflicts, such as pipeline interference and problems of insufficient space, can be avoided in the early stages of planning, it facilitates the achievement of project objectives in quality, scheduling, and cost.

Aug 1, 2013

By William H. McCracken, William G. Holroyd

"The People&apos;s Republic of China could very well be considered the largest untapped mineral and metal resource in the world. The proven reserves of antimony, barite, bauxite, fluorspar, graphite, lithium, magnesite, mercury, molybdenum, phosphate, pyrite, rare earths, talc, tin, titanium, tungsten, vanadium and zinc are among the largest in the world.Any company involved in the purchase or supply of industrial raw materials has undoubtedly followed the phenomenal growth of some of the Chinese mineral commodities, where growths in production of more than 200010 have occurred during the past ten years, for commodities like barite, cement, gold, gympsum silver and talc. Others, like bauxite and phosphate, experienced production increases in one year alone of over 45%, from 1986 through 1987!A popular rationale in the United States during the past two years has been the acknowledgment by Professor David Calleo, of Johns Hopkins School of Advanced Studies, that ""America is not sinking-the rest of the world is rising"". While we recognized this rise to be that of economic power for Japan, Korea, Brazil, Taiwan and, more recently, the newly-combined Germanies, China has also successfully completed her own modern five year development binge. But with each boom there is also a bust, and the start of the 1990sfor China shows signs of economic distress. China posted a budget deficit equivalent of US$1.9 billion in 1989 coupled with official inflation at 18010. Projections for 1990 are for US$1.8 billion deficit and inflation as high as 24%. However, government spending in the first seven months of the year climbed 16.4%, outpacing an 11.6% rise in revenue. Spending increases have been related to the government policy to keep prices on domestic goods artificially low, through subsidies, and to bailout inefficient state companies."

Jan 1, 1991