Search Documents

By Olivia Gamache

When working in remote and extreme environments, projects are faced with new challenges for engineering and project execution. This is heightened when also working in countries with a developing environmental regulatory framework, small skilled workforce available for recruitment, and minimal infrastructure such as power, roads, and water. There is an increasing realization that social and environmental aspects need to be built into project execution. Giving proper attention to these issues during project development and execution, and maximizing opportunities is an ongoing challenge.

May 1, 2013

By E. Busse

"Heath Steele Mines Ltd. operates a lead-zinc-copper mining and milling complex in New Brunswick.• During the past seven years, as ore reserves increased, the mill capacity was first expanded to 1,600 tpd and then to 3,000 tpd. In the last expansion, instead of building a completely new 3,000-tpd mill, or adding to existing installations, Heath Steele retained service facilities, buildings, ore bins, Jab, etc., and removed and replaced almost all existing process facilities. Requiring a complete mill shutdown, the expansion had to be carried out in minimum time. Also, new equipment had to fit into existing space. Critical path networks of the project were prepared, a tight schedule for construction was mapped out and progress charted daily to detect problems before they could interrupt the schedule. Heath Steele supervised the purchasing, handling and storage of new equipment, maintained liaison with the engineering contractor and became a sub-contractor, using its own staff to install all flotation equipment and process piping. The 1,600-tpd installation was dismantled and a 3,000- tpd unit was successfully put onstream in 5 months - on time and within budget. One benefit stemming from the expansion: production increased 87 per cent while operating and maintenance labour rose only 8 per cent."

Jan 1, 1972

By Ivan Malinsky, Gérard Castonguay

"On a développé un procédé qui donne une fonte (2,3% C, 0,07% V) du V2O5 (99%) et un rutile synthétique (94% TiO2) à partir d'un minerai, dont les réserves au Québec sont importantes. Le procédé comprend les opérations suivantes: 1) la concentration magnétique du minerai (30% Fe, 9% TiO2 et 0,65% V2O5) pour produire un concentré (65% Fe, 7% TiO2 et 1,6% V2O5); 2) le smeltage du concentré aggloméré dans un four à arc, sans fondant, pour produire une fonte et une scorie (30% FeO, 40% TiO2 et 8,0% V2O5) qui contient plus de 95% du vanadium et du titane présents dans le concentré; 3) le grillage alcalin (37% Na2CO3) de la scorie suivi d'une lixiviation à l'eau et de la précipitation de l'hexavanadate d'ammonium à partir du filtrat; 4) la lixiviation du résidu par l'acide sulfurique pur ou usagé pour produire un rutile synthétique. Un estimé préliminaire de la valeur économique du projet laisse croire à sa rentabilité à la condition que l'investissement pour le smeltage soit inférieur à environ 400$/tonne de fer.IntroductionLes gisements de magnétites titanifères sont nombreux dans le monde. Ils consistent en une magnétite étroitement liée a l'ilménite, La teneur trop élevée en TiO2 empêche l'exploitation de ces gisements pour la production de fer. Cependant, dans certains cas, la magnétite a une teneur intéressante en vanadium qui peut rendre l'exploitation de ces gisements rentable. Aujourd'hui, les magnétites titanifères constituent la plus importante source de production de vanadium. On estime qu'environ 70% du vanadium produit provient de ces sources."

Jan 1, 1983

By G. Van Weert

ABSTRACT When exposed to microwaves, rocks containing sulphides adsorb energy preferentially over barren gangue and quickly become warmer with minimal energy consumption. This effect makes subsequent machine sorting of ore from waste rocks or overburden possible using infrared sensing. This paper reports on the 2450 MHz microwave response of a variety of sulphide minerals by mesh size and spatial distribution, as they might occur in ore rocks. The implications for infrared ore sorting are discussed.

Aug 1, 2011

By G. Van Weert, O. Wang

ABSTRACT: When exposed to microwaves, rocks containing sulphides adsorb energy preferentially over barren gangue and quickly become warmer with minimal energy consumption. This effect makes subsequent machine sorting of ore from waste rocks or overburden possible using infrared sensing. This paper reports on the 2450 MHz microwave response of a variety of sulphide minerals by mesh size and spatial distribution, as they might occur in ore rocks. The implications for infrared ore sorting are discussed.

Jan 1, 2011

By Peter M. Power

A microscopic study was made of a series of simultaneous slag and metal samples taken from a low carbon basic open hearth heat. An attempt was made to identify the various micro-constituents found. As the various impurities in the bath are oxidized, the metal structure changes from that of high-phosphorus white cast iron to that of low.-carbon steel. A detailed study of phosphorus distribution is included. The acid run-off slag has an .acicular orthosilicate structure which changes on 'shape-up' to a very basic tri-calcium silicate and calciuim ferrite structure. Many unidentified minor constituents are present in the slags. Though metallography will never replace chemic.al analysis of the bath, the microsopic study of polished slags has some promise of being useful in slag control work.

Jan 1, 1956

By T. Grammatikopoulos, SGS Canada Inc.

"The Nechalacho rare metal deposit, located in the Northwest Territories, Canada, is currently being taken through Feasibility Study by Avalon Rare Metals Inc. QEMSCAN analysis and supplementary electron microprobe analysis were utilized to identify and quantify the mineralogy of the deposit, and determine REE distribution among the minerals. QEMSCAN mineralogy was performed to provide textural information on the mineralization, determine the variability of the ore and identify REE domains, and the liberation and association of the REE minerals. The sample matrix consists predominantly of silicate minerals. The REE minerals include allanite, monazite, synchysite, columbite, fergusonite, and bastnaesite. Zircon is present in considerable amounts and is a REE carrier. Fergusonite and zircon account for most of the HREE, and monazite, allanite, synchysite and bastnaesite the LREE. QEMSCAN mineralogical data is extremely valuable in assessing the mineralogy of the ore. The data are implemented to define the mineralogy of the ore body, support metallurgical test work, and predict recoveries and grades.INTRODUCTIONThe term rare earth elements (REE) is used to describe the 15 lanthanide elements or metals and, more recently, the metals yttrium and scandium, which display similar physical and chemical properties.Economic and potentially economic REE deposits form two main groups, a more commonly occurring “light rare earth element” (LREE) group containing lanthanum, cerium, praseodymium, neodymium, and samarium and a less commonly occurring “heavy rare earth element” (HREE) group which, in addition to the LREE, contains elevated concentrations of the more valuable REE, europium, gadolinium, terbium, dysprosium, holmium, yttrium, erbium, thulium, ytterbium, lutetium and scandium. The first group is hosted primarily by carbonatites and the second by highly alkaline (Na + K > Al) silicate igneous rocks. The LREE are produced mainly from bastnaesite, monazite, etc., while HREE are produced almost exclusively from low-grade secondary ion adsorption clay deposits in which the REE are adsorbed onto the surfaces of kaolinite and halloysite, clay minerals produced by the weathering of granite and sediments. HREE are also found in fegusonite, zircon, xenotime, etc but are not produced presently from these minerals. China is responsible for 97% of the World’s production of the REE, mainly from the giant Bayan Obo, carbonatite-related deposit and from the clay deposits mentioned above.Quantitative automated mineralogy is increasingly being applied to ore deposits. It helps users to understand and improve mineralogical parameters for geological and metallurgical purposes. Data include textural characterization, to quantification and distribution of ore and gangue minerals, liberation and association of the REE minerals. The data can be used to define mineralogical domains and predict the metallurgical response of the ore (Gunning, de Souza, & Grammatikopoulos, 2009)."

Jan 1, 2012

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which 'the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

By H. W. Parsons

Several low-temperature, dry chlorination processes for the treatment of sulphide minerals are reviewed, in a chronological order. These processes include the following: the Swinburne-Ashcroft, Baker-Burwell, Maim, Comstock-Wescott (Aldermac) and the Mitterburg Mining Process. Dry chlorination investigations at the Canadian Mines Branch (now CANMET) and the U.S. Bureau of Mines are discussed, as is a proposed process by the South Africa National Institute for Metallurgy. The techniques used in the process are discussed, as are the shortcomings, problems and failures of the methods.

Jan 1, 1978

By S. Koski

The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60? x 113" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns. This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining.

Jan 1, 2012

By P. Chryssanthakis

"The aim of this study is to give a better understanding for the behaviour of the composite material RRS and the synergy effect of its components while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10 m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. The newest part of the lower part of the Q-chart gives more information on required support compared to older Q-system versions. The RRS can be described as a three part composite material with the 3rd component being the reinforced concrete beam (with no fibers) and with steel rebars that are placed in groups and sprayed with pneumatically applied shotcrete in layers. The RRS usually have a total thickness varying between 0.20 and 0.50 m and a width between 0.25 and 0.60 m respectively. They are placed at different distances along the tunnel axis depending on the rock mass quality.In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. This was done by writing a FISH subroutine which is implemented in the discontinuous numerical code Universal Distinct Element Code (UDEC) that takes into account the characteristics of the reinforced beam (height, width, number of steel rebars, and spacing) in the calculation process. A rather extensive parametric study has been run by using the same key input rock mass parameters and in situ stresses (?H/?v = 0.5), and changing only the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam.The results show that: a) the S(fr) is almost overloaded in the first 4 hours after application in both tunnels; b) on the S(fr) and steel rebars, the stresses, axial and shear loads, as well as moments are decreasing after 16 hours and 28 days; and c) the bolts loads are increasing with time. The observed reduction in stresses and loads in both the S(fr) and reinforced beam is surprising. A possible explanation is that tunnel arches are self-supported to a lesser extent as time progresses due to redistribution of stresses in the nearby rock mass through the radial bolts. The loads in radial bolts are increasing by almost 25%. This can be seen from the overall results as we observe an increase in maximum principal stresses, displacements, shear displacements along joints and hydraulic apertures compared to tunnel baseline that has no support of any kind."

Jan 1, 2015

By L. H. Shang

The 319 Al-Si alloy is one of the most prominently used aluminium-based alloys in motor vehicle and engine applications, Microporosity present in 319 alloy castings reduces the load bearing capacity of the castings, The quantitative prediction of microporosity levels in Al-Si castings has been a subject of much interest for several years. In this research a new criteria function, tf 1,98 R13° (tf: local solidification time, R: cooling rate) was developed by multiple regression analyses, correlating thermal data from simulation studies to experimentally obtained microporosity values. This new criteria function gives a general prediction of microporosity in 319 Al-Si castings.

Jan 1, 2005

By F. R. Archibald

SINCE the opening of the Beattie mine, in 1933, the concentrate produced by flotation has been considered refractory. As the gold extraction by cyanidation was poor, the concentrate, during the first four and a half years of operation, was shipped to a smelter for further treatment. After the installation of the cyanide plant, in 1934, seventy per cent of the gold in the concentrate was recovered before shipment to the smelter. In 1937, a roasting plant was built so that treatment might be complete at the mine. Much experimental work had been done by a number of investigators prior to the installation of the roasters, but none of them had seriously attempted to identify the causes of, or the elements responsible for, the refractory behaviour of the concentrate. Intensive investigation in this direction commenced in the Beattie lab-oratory in July, 1938, has led not only to the identification of several causes contributory to the refractory behaviour, but also to revisions in procedure and principles with respect to roasting Beattie concentrate in particular and arsenical concentrates in general. The accuracy of the identification of these causes and the soundness of the principles is borne out by interpretation of roasting plant records, by improvements and simplification since applied. to plant operation, and also by laboratory and test-plant results on arsenical concentrate produced by another mine. It is the purpose here to present an account and interpretation of the laboratory investigation, together with a correlation of laboratory and plant results. Incomplete extraction of the gold by cyanidation after roasting is due primarily to the nature of the material roasted, and secondarily to the manner in which it has been roasted. There is a possibility that better extraction may be obtained by improvements in both particulars.

Jan 1, 1939

By A. K. Croteau

"At Craigmont Mines Limited, Merritt, B.C., the mining practice of trackless sub-level caving was started in the latter part of 1966. This type of mining was new to the mine personnel and the mining industry of Canada as a whole. Sub-level caving has presented many old and a number of new problems in maintaining the equipment used in this method. This paper will deal with some of these problems as they affect this particular mining operation. It will be impossible to review all phases of the equipment, but an attempt will be made to cover the most pertinent aspects in maintaining the drilling, mucking and hauling, and auxiliary equipment."

Jan 1, 1970

By V. Maazallahi, A. Rouleau, A. Saeidi

"The geometry of the terrain topography before and after the failure are the essential factors for analyzing a landslide and for the design of remedial works. This paper presents a method to determine these factors, considering that the determination of the slide surface profile is difficult and costly using traditional methods and the pre-slide topography data is often not available. The presented method to locate the 3-dimensional geometry of the slide surface is based upon determining the slide surface in 2- dimensional vertical sections. This method utilizes post-slide topography of the area to determine the pre-slide topography and uses equations to estimate the pre-slide situation using a statistical process applied to points located on the sliding mass. This method is tested on the Maskun landslide in Iran. The results indicate the applicability of the proposed method to obtain the key factors for the back analysis of a landslide in a cost effective manner.INTRODUCTIONProbably the most reliable method of determining the strength of soil and rock mass is to back analyze a failed or failing slope (Caia et al. 2007; Wyllie & Mah, 2004). This method is used in geotechnics for estimating geotechnical parameters of the rock and soil mass (Sakurai et al., 2003; Frayssines and Hantz, 2009; Cepuritis et al. 2010), but it requires that the failure mode is well established and that there is complete and precise information available on the slide surface and the sliding mass (Sjöberg, 1996). Measurement of the slope profile before failure provides the basic information required for a back analysis (Hock & Bray, 1981). The post-slide topography is another key factor. The back analysis process for determining the actual strength parameters of soil or a decomposed rock mass after a landslide requires knowledge of the sliding mass geometry, both before and after the sliding event. Many studies are reported in the literature about the application of back analysis for determining geotechnical and geomechanical parameters of rock and soil mass (Sakurai et al., 2003; Cepuritis et al. 2010; Frayssines and Hantz, 2009, Hussain and Stark, 2011), but they generally present little information about the geometry of the slide surface, and the weight of rock and soil mass that slid, although these factors are the most important parameters for back analysis process. Liang and Xue-song (2012) determined the slip surface having the minimum factor of safety (called critical slip surface in deterministic analysis of slopes) and the slip surface with the minimum reliability index (called critical reliability slip surface), but they have not considered the actual profile and geometry of the slide surface. Rocscience (2013) proposes the back analysis option in the Slide software for slope stability study, but it requires an imposed slide surface as input; alternatively, one can estimate by a finite element analysis the surface with the minimum factor of safety. However, this estimated surface is very likely different from the actual sliding surface, considering the uncertainties in input data of the finite element method."

Jan 1, 2015

By Krishna Parameswaran

In this paper, we attempt to answer an often asked question, how can metal mining be compatible with the principles of sustainable development. Starting with the classic Brundtland Commission definition of sustainable development as "development that meets the needs of the present without compromising the ability of future generations to meet their own needs," we make the case that mining is or should be sustainable, using examples of sustainable practices at ASARCO LLC, an integrated U.S primary copper producer. These examples cover the entire mining cycle starting with exploration, mining, beneficiation, smelting, refining, closure and post-closure and post-mining land use. It is hoped that the presentation will challenge the mining industry to even greater innovation as future mineral development projects are planned.

Jan 1, 2015

By L. Heber Cole

The search for potash in western Canada during the years of the great war led to the staking of claims on many of the "alkali lakes" and sloughs which occur in numerous localities in the morainic areas of the prairies, as well as in British Columbia, in the hope that potash salts would be found in commercial quantities. While the search for potash, up to the present time, has been disappointing, the prospecting of these areas has demonstrated that Canada possesses large reserves of sodium and magnesium compounds, principally in the form of sulphates, carbonates and chlorides. he writer first became interested in these deposits in 1911 while investigating the sodium chloride springs of northern Manitoba. In the fall of that year a number of the sulphate ? deposits in Saskatchewan and Alberta were visited, but owing to the excessive rains at that period, all the deposits were under water and only a few brine samples were obtained. Owing to pressure of other work investigations of the alkali deposits in western Canada, by the Mines Branch of the Department of Mines, could not be undertaken until the field season of 1921, but since that time the work has been continuous. During the summer of 1918 a reported discovery of a large deposit of potash bearing salts was featured in western papers and in a short time practically all the lakes and sloughs of the prairie provinces, which showed the least indication of being saline, were staked for potash. This reported discovery was not substantiated on investigation and many of those who had staked claims allowed them t~ lapse without the slightest effort to determine the character of the material in the deposits which they? had leased.

Jan 1, 1924

By D. R. Derry

"IT WOULD TAKE a braver man than I to try to forecast the future of mining exploration far into Canada's second century. Even to look ahead ten or twenty-five years we must review the figures of the fairly recent past -and I have found this quite a time-consuming but interesting job -in order to find trends and project them into future years. The trends to which I will refer are: firstly, the annual expenditure on exploration and its relation to value of output; secondly, the discovery rate and its relation to production initiations; and thirdly, the methods by which discoveries have been, and will be, made. Exploration Expenditures Figures on the annual expenditure on mining exploration in Canada have been collected and published for some years by the Do-minion Bureau of Statistics. These have some unavoidable limitations; e.g., in the varying definition between one company and another of what comprises ""Exploration"" and in the difficulty of getting complete returns. However, although the actual figure for a given year may be subject to question, I believe that the relative figures from one year to another are reasonably reliable. There is also a lapse of time between the collection of data and publication -the last published figures are for the year 1963. In bringing the figures up to date to 1966 I have canvassed eight of the larger mining and exploration companies and obtained their figures for 1963 to 1966 inclusive, and then averaged these for each year and applied the progression to the 1963 figures."

Jan 1, 1968

By D. W. Davis, P. Landais, L. J. Robb

Abstract -Nodules of carbonaceous matter have been observed in several Archaean peraluminous granites adjoining the gold- and uranium-bearing Witwatersrand Basin. These nodules, which resemble solid bitumen, usually replace uraninite or uranothorite and are paragenetically late. They show many similarities to kerogen seams and nodules associated with the conglomerate horizons in the Witwatersrand Basin, including composition, maturation, intimate association with uraninite, and a late paragenesis. U-Pb isotope ratios for granite-hosted and Witwatersrand kerogens define a single, albeit somewhat diffuse, Pb-loss discordia suggesting an upper intercept age of circa 2300 Ma. Carbon isotope analysis indicates lighter ?13C values for the granite-hosted nodules than for the sediment-hosted kerogen seams. Raman spectroscopy indicates that granite-hosted kerogen is more highly ordered than Witwatersrand seam kerogen. A model is presented which links the granitoid­ and sediment-hosted organic matter to an event of oil generation in the Witwatersrand Basin circa 2300 Ma ago. Light hydrocarbons migrated through the sediments and into underlying/adjacent granitic rocks, undergoing polymerization and accumulation in response to radiation accompanying the presence of high-uranium phases.

Jan 1, 1994

By J. E. Gillespie

Introduction Mineral wool may be defined as "rock, slag, or glass fibres made by a process of melting and blowing by steam or air, containing a minimum of oil and unfiberized material" (U.S. Bureau of Standards CS 117-44). The earliest production of the material was in Wales, about one hundred years ago. In the United States, the industry daces from 1870 when a plant, using slag as raw material, was established in Greenfield, New Jersey. It was not until 1897, however, that large-scale production was commenced on this continent at a plant in Alexandria, Indiana, which utilized rock from nearby deposits. Today, mineral wool is manufactured in many parts of the United States and Canada, the plants for the most part being in close proximity to deposits of suitable rock or to sources of slag. In the United States there are some seventy-five producers with a total annual capacity of nearly one million tons of wool. In Canada, in 1946, eleven manufacturers produced about fifty million square feet of batt-type mineral wool insulation material. Mineral wool is, perhaps, the most efficient of all heat-insulating materials and, moreover, it is fireproof, extremely durable, and insect- proof. Its high efficiency is due to the very low thermal conductivity of the fibres themselves and to the fact that the produce as marketed contains up to 90 per cent non-conducting air space. Depending on the degree of compression of the fibres in the manufactured product, the specific gravity ranges from 2 lb. to 10 lb. per cubic foot. Products Marketed Following are the principal forms in which mineral wool is marketed: Blanket. - Mineral wool with or without reinforcing on one or both sides, with various types of confining media, all suitably bound together.

Jan 1, 1948