Search Documents

The preconcentration of uranium ore by radiometric ore sorting at Mary Kathleen Uranium Ltd. is described. The operation of the ore sorting machines is discussed in detail and performance results obtained with the existing system are presented.

Jan 1, 1978

By Arumba J

In the Mount Victor area of the Eastern Highlands Province, re- connaissance geological mapping and new micropalaeontological data have revealed the existence of at least three small thrust- bound windows exposing late Middle to Late Cretaceous (Late Aptian-Early Albian and Late Santonian-Maastrichtian) sedimen- tary rocks and pillow lavas, Latest Paleocene- Earliest Eocene pillow lavas, and Latest Paleocene-Earliest Eocene bathyal micrites. Late Middle Eocene to Late Eocene inner neritic bioclastic micrite units also occurs in thrust contact with Middle Miocene Yaveufa Formation volcanolithic conglomerates. The Cretaceous and Early Tertiary units appear to be thrust-bound and are best exposed in a window just south of Mount Victor, and in two smaller windows to the east. The inner neritic Eocene limestone occurs in a thrust-bound sliver within the Yaveufa For- mation near Obura. The windows occur within extensive out- crop of Early Miocene Omaura Formation and the Yaveufa For- mation. Thin-bedded grey mudstone, siltstone and sandstone, typical of much of the Chim Formation form only a small part of the exposure of Cretaceous rocks. Thick-bedded volcanolithic conglomerate, spilitic pillow basalts, and welded basic tuffs domi- nate the Cretaceous section. The stratigraphy and structure of the Mount Victor area is similar to the Menyamya area, the Aure Scarp, and perhaps the Tapini area. This study has raised the possibility of widespread thrust- ing in the Kainantu area, and suggests that the boundary between the Omaura and Yaveufa Formations is thrusted, at least locally.

Jan 1, 1997

By Mackenzie J. M W

The mechanism of clay slime flocculation in coal washing circuits is considered and it is concluded that polymer flocculants are most suitable. It was found that the addition of sea water with a polymer flocculant improved flocculation and settling, and it was also found that dilution of a flocculated pulp increased floc size and hence settling rate.In predicting plant consumption of reagent it was found that cylinder tests, or even pilot plant tests, could give erroneous results, particularly on flocculated pulps. Different flocculants may, however, be compared in cylinder tests.For filtration, flocculation with Separan plus sea water was much more beneficial than flocculation with Separan alone.INTRODUCTIONDuring the mining of coal, and its subsequent beneficiation by washing, large quantities of minus 10 mesh material are produced. This fine material, which consists of broken down shales and fine coal, causes difficulties in water clarification circuits, in refuse disposal, and in filtration of fine coal.These difficulties can be largely overcome by flocculation, and this paper discusses the mechanism of flocculation, the methods by which a selection of flocculant may be made from the large number available, and the limitation of the prediction of plant performance from laboratory tests. This work applies particularly to the washeries of The Broken Hill Proprietary Co. Ltd. (B.H.P.) and Australian Iron and Steel Ltd. (A.I. & S.) .

Jan 1, 1962

By Crawford M

During the initial development of Mount Isa Mines power was supplied from a temporary power plant situated near the Man & Supply Shaft. The main power plant was placed in service early in 1931 and then comprised two Babcock and Willcox boilers, fired by pulverised fuel, and two British General Electric Company's turbo-alternators of 5,000 kW. each. Both plants have been described by A. F. McAskill in the Journal of the Institution of Engineers, Australia.From 1931 power demand progressively increased due to greater production, further mine development in the harder sulphides increased pumping for mine drainage and additions to mill and smelter until, by 1935, the plant was inadequate for further output commensurate with a reasonable safety margin.Coincident with the added power demand, operating conditions involved a fuel problem which could not have been anticipated. The ash content of the fuel supplied gradually increased from 13% to 16-5%, while the melting point of the ash decreased with higher pyrite content.Temperature conditions in the furnace required careful control to cope with ash formation and slag accretions.Consequently brickwork, excessively stressed on water walls, was constantly under repair, and required suspension periods of 50% of operating time for cleaning and overhaul.Load conditions varied continually, therefore the high heat liberations in the furnace, necessary to accommodate peaks in fluctuating output, resulted in ash fusion.

Jan 1, 1939

By Porter I

Rock mass classification systems have emerged as a powerful tool which can be used for assessing ground conditions and determining support requirements in underground mines. They should not be used as a substitute for complete engineering design, but rather as a supplement to observational methods and analytical study. In general, the use of rock mass classification is attractive, but each classification system has various deficiencies. Use of any particular system should be made only with knowledge of that systems limitations. It is desirable to employ a number of systems and design methods which will allow for comparison and lead to a better understanding of the rock mass condition.The Rock Mass Quality system (Q-System), developed by the Norwegian Geotechnical Institute, and the Rock Mass Rating (RMR) System, Bieniawski, were designed primarily for civil engineering structures. Laubscher et al (1978) further developed the RMR-system specifically for rock mechanics engineering in the mining industry. A method of stope design, which introduces a stability factor for the rock mass and compares this with hydraulic radius, was developed by Mathews et al (1981). This paper reviews the above systems by applying them to stability assessment of crown pillars in two Australian metal mines and provides a critical analysis of the various approaches. In particular each system will be analysed to determine its suitability for use in crown pillar design. The most suitable system(s) will form the basis for future development in crown pillar stability analysis.

Jan 1, 1994

By Roberts C

The satisfactory testing and characterisation of mineralisation amenable to heap leaching, is of prime importance to successful operation of a project. This paper outlines a methodology for assessing material suitability. A general model is used for classing material types for suitability for treatment and for economic analysis. The four levels of these are overburden, oxide, transitional and unoxidised materials. During exploration, reverse circulation (RC) drilling can be used effectively to define these zones by a combination of logging, analysis and provision of cuttings for column leach and bottle roll trials. RC cuttings can he used effectively for column leach trials, when calibrated against conventional processing-sized samples, obtained from surface. Tbis allows metallurgical testing to depth and definition of transitional ore types and the base of oxidation, accurately and economically with an acceptable density of samples. The accurate prediction of base of oxidation and variations in recovery with depth and ore types can be used to develop 'economic' pit designs with zones of variable recovery. Petrological studies of leaching results and examination of mineralisation types carried out on concentrates, provide information on gold distribution and physical and chemical constraints. The examination of concentrates can be particularly useful for types of mineralisation when overall gold content is frequently at or below one pan per million. Explanation of anomalous recovery of gold grains in dense goethite and solution-robbing by carbonaceous material can be identified by use of petrological and scanning electron microscope. An understanding of the role of the host rock in leaching characteristics can also he provided by petrology where siliceous or clayey materials can require significantly different treatment.

Jan 1, 1994

By Sheard SN, Tucker DH

Sampling procedures are an important aspect of geophysical exploration survey design. It is good practice that the selection of survey parameters ensures that the signal to noise ratio is optimised, while minimising survey cost.Sampling considerations for any geophysical method include the size of the target, scale of observation, aliasing associated with station and line spacing, nature and extent of overburden, and the presentation of data.As a guide to survey design, the specifics are discussed for three geophysical techniques in common use in mineral exploration; these include the magnetic method, transient electromagnetics and induced polarisation.

Jan 1, 1976

By Boyle L. A

A positive displacement pump is being dev eloped for pipeline transportation of coking coal to a -50 mm export specification, at a con- centration and velocity which will allow trans- portation in the plug flow region, minimising degradation of the particle structure, and pipe= line friction losses which will be lower than with turbulent or laminar flow. Pump operation is by hydraulic powered free pistons in a rota- ting cylinder block, with cylinders overlapped by stationary inlet and discharge ports in a water lubricated and sealed rotary valve. Before this development coking coal was not considered suitable for transportation in slurry form, for the valves in the double act- ing duplex piston pumps used for slurry pipe- lines, cannot be divorced from the slurry and require that the solid material must be reduced to a fines'consistency before introduction into the pump suction. The hydraulic transportation of 10 million tonnes of -50 mm coking coal, 50 km from the Bargo area west of the escarpment to an offshore shiploader at Port Kembla is feasible. Study shows that economic factors alone would dictate that the development of a pumping system for long distance transportation of coking coal is necessary. The greatest impact from the slurry transportation of coking coal would be the

Jan 1, 1976

The production of synthetic crude oil requires a suitable coal or a coal extract modified by hydrogenation for pyrolysis. Existing classifications are broadly based on historical and current needs. One, Seyler's, is based on a visual display which can be used to present petrographic bounds. The analysis of the coal extracts from solvent hydrogen-donor testing allows an experimental limit to be described and a plant limit to be indicated. Australian black coals are discussed within these petrographic and plant bounds and their limitations as a feed for the production of synthetic crude presented. Potential uses for the aromatic liquid products are suggested. The application of the diagram as a screening procedure for sub-hydrous coals is described.

Jan 1, 1975

By S Basu, P M. Midhun

Electro-Slag Remelting (ESR) is a process capable of producing ingots with much lower centre-line segregation and better internal soundness than conventional ingot casting processes, as well as lower inclusion and sulfur concentrations. This process is commonly used for alloyed steels intended for critical applications like components of marine turbines, supercritical powerplants and rocket motor casings. It involves melting a metal electrode using electrical resistive heating in a slag pool and re-solidification of the resulting metal droplets beneath the slag layer, forming an ingot. Conventional ESR fluxes consist primarily of CaF2, Al2O3 and CaO, along with minor concentrations of SiO2, MgO etc. The emission of fluoride vapour from the molten slag causes several environmental and health problems, triggering a need to develop and reduce the fluoride content in the ESR flux. The present study aims to develop low-CaF2 alternatives to commercial ESR fluxes without compromising on productivity and the surface quality of the refined ingot. Thus, the modification in chemical composition needs to satisfy properties like electrical resistivity, viscosity and liquidus temperature, essential for efficient ESR operation. Since electrical resistivity and viscosity are highly dependent on the ionic structure of the molten slag, it is important to understand the effect of compositional modification on the structure of the flux. The present study employs Fourier-transform infrared spectroscopy (FT-IR) and Raman spectroscopy to investigate the structural variations in the modified fluxes, especially the effect of changing SiO2 concentration, in comparison with conventional CaF2-rich fluxes. Additionally, thermal analysis (Differential Thermal Analysis (DTA) and Thermogravimetric Analysis (TGA)) has been carried out to characterise the melting behaviour of the fluxes. The findings are compared with simulations carried out using the FactSage™ software, ver 8.3 (GTT Technologies, Aachen, Germany). Simultaneous analysis of liquidus temperature and the structure is expected to help in identifying the practical suitability of modified ESR flux compositions for industrial implementation.

Jun 19, 2024

The design of water and ore addition points has an important bearing on the ease of operation of a grinding circuit. The nature of some of the design decisions and the possible options of the designer are discussed. For example, design decisions determine the ease of alteration and measurement of flowrate, the ease of maintenance, and the effectiveness of feed- back control loops which maintain material inputs (water and ore) at required values. To illustrate discussion in the paper, a grinding circuit which contains one rod mill and one ball mill in series is used. Practical ramifications of desigl decisions :;ne stressed.

Jan 1, 1978

By K Uchino, M Inoue

Self-potential anomalies are generated by fluid pressure gradient, by temperature gradient or by chemical gradient. On the basis of this principle, a new technique is proposed to locate the fire source of spontaneous combustion of coal by the self-potential method. In order to investigate whether this method can be applied to locate the spontaneous combustion of coal in practice, surveys of self-potential distributions were undertaken in a coal waste pile undergoing spontaneous combustion. The results showed that there is a negative centre of the electrical potential distribution in the measurement area. The potential in this centre is about 140 mV lower than that in the surrounding area. Moreover, the negative centre of electrical potential distribution almost overlaps with the high temperature zone. Therefore, it is concluded that it is possible to locate the heat source by the measurement of self-potential distribution.

Jan 1, 2005

By Doyle J

The direct method of gas content determin ation developed by McCulloch and Diamond of the U.S.B.M. has been adapted to estimate the gas content of coal seams from slim exploration borecores in the Southern Coalfield. Emphasis has been placed on the measurement of this parameter without the physical destruction of the core which is required for subsequent chemical analysis. In field and laboratory equipment is simple and inexpensive. It enables the determination of lost and desorbed gas from a fresh geological core. Residual gas is not measured but is considered to be relatively low and of no consequence in ventilation considerations. Results to date show good correlation with those obtained from underground face samples. Gas contents from the mined seams varying from 2 m3/tonne to 14 m3/tonne have been measur- ed with this apparatus. Gas desorption characteristics of South Coast coals have been found to closely follow exponential mathematical Models.

Jan 1, 1983

By Bond W. F, Sharry P. V, Onley P. G

The use of Decision Analysis is becoming more widespread in industry as a whole, and there is considerable scope for its application in the mining industry. Wherever decisions have to be made, whenever risks have to be taken, whenever uncertainty exists or whenever judgements have to be made, then Decision Analysis can be used. In the mining industry we daily make many decisions involving risk, uncertainty and judgement. Expansion and diversity will only increase the need for balanced decision making techniques. This paper seeks to describe the history and principles of Decision Theory, and to illustrate the various modelling approaches using three fictitious yet realistic case studies. Decision Analysis logically integrates the quantifiable and seemingly non-quantifiable aspects of a decision problem into a coherent, explicit and rational solution. It also allows the decision-makers to see the full impact of each variable or uncertainty, and hence focus on the key aspects that influence the solution.

Jan 1, 1996

By K Thompson

The Diavik Diamond Mine is a world-class operation located in an extreme environment 220 km south of the Arctic Circle in CanadaÆs Northwest Territories. The mine has a number of distinctive characteristics û such as limited winter access via an ice road, mine infrastructure being located on an island, with mining taking place behind dykes holding back a lake, temperatures at the mine that get down to -45¦C in winter, and the presence of bears, wolves, foxes and wolverines! One thing that Diavik does have in common with other mines around the world is the need for reconciliation. In late 2005 Diavik implemented SnowdenÆs Reconcilor software system to facilitate the process of reconciling geological models, mine plans, production data and plant results. This paper provides a case study of the reconciliation system implementation. It outlines the migration of Diavik away from a comprehensive and effective spreadsheet-based reconciliation process to a commercial grade, automated and web-based information management system. This paper documents the reasons for moving away from the spreadsheet system, the key parameters used for reconciliation, and the benefits gained by closing the loop between reconciliation and ongoing process improvement.

Jan 1, 2006

By Perry JH, King RL

The Bureau of Mines in cooperation with Kaiser Steel Corporation conducted two methane drainage studies in an advancing section of the Sunnyside No. I Mine where production was being severely hampered by methane emissions. A total of six horizontal aoreholes were completed during the studies to an average length of 291 meters. Total gas production from the boreholes as of December 1981 has exceeded 6,088,800 m3. Methane emissions into the section were reduced by 40 pct as a result of the first drainage system. The second drainage system is currently producing 11,328 m3/day from four Doreholes. Mining of the section and cementing of the horizontal horeholes is expected to begin within 2 Years.

Jan 1, 1982

By Higuchi K

For the mechanisation or automation of mining, recognition of the shape of mined cavities is basic information. A three dimensional shape measuring system, developed and tested, includes an ultrasonic range finder which is attached to the tip of a serial link manipulator. The range finder can be moved to any position and direction in the operational space of the manipulator. The position of a point on the surface of the object is obtained from the position of the range finder, the direction of the beam of the ultrasonic waves and the measuring distance of the range finder.To avoid collision between the sensor and the object, the manipulator is controlled to trace the surface of the object For the tracing control, another ultrasonic range finder is employed. The test results show that the developed system has high performance.

Jan 1, 1991

By H Nikraz, E Jamieson, D Cooling

The use of red sand as fine aggregate in concrete manufacture has been investigated as well as the use of fly ash as a cement replacement. The experimental work consisted of casting various concrete mixes including a control and comparing standard properties. Properties tested included compressive strength, splitting tensile strength, flexural strength, modulus of elasticity, water permeability, chloride diffusion, pH dependence leaching and particle morphology. The results show that the concrete strength is not significantly affected when natural sand is replaced completely with red sand. The durability tests indicated high water permeability and high chloride diffusion due to the porosity of the red sand concrete, likely due to the low slump value. Leaching tests did not exceed New South Wales EPA guidelines.

Jan 1, 2006

The exploration and mining risks are investigated and compared to the risks of smelting, secondary processing and other normal industrial activities. This study concentrates on the risk before, or at the investment decision. Internal and external risks are distinguished. Internal risks are the risks inherent in every engineering design and common to all projects. The main external risks are the financial risk, changes in prices, location problems and geological factors. Financial risks concern every capital-intensive and export-oriented project and cannot be considered as typical mining risks. Changes in prices, i.e. the market risk, concern every industry using raw materials, but the market risk is especially accentuated in the mining industry. Problems of location and infrastructure are normally more significant in mining than in other projects, and geological risks are unique to mining. All these risks associated with mining projects combine to form a risk at least twice as high as that for other normal industrial activities. Within the range of profitability of mines, which on average is the same as in the manufacturing industry, only a few highly profitable mines exist. These few mines are the sole reward for the high risks taken.

Jan 1, 1986

By Shklyar FP, Babushkin NM, Bokovikov BA, Fedotov PB

A mathematical model for gas flow dynamics and heat and mass transfer processes occuring in the tuyere raceways and in the zone of the final for- mation and heating of pig iron and slag has been developed and simulated on a digital computer. It takes into account the formation and size of the raceway zones, combustion of coke and its substit- utes, oxidation of the metal, radiation from the gases to the raceway boundaries, physical heat losses and the direct reduction of the pig iron elements below the raceway zones. To evaluate the distribution of heat produced by the oxidation of metal between gases and prod- ucts of smelting, the problem of heating the mat- erials in the raceways with the sources of heat in the materials under conditions of intensive gas circulation in the raceways is solved. To determine the amount of heat transferred by radiation from the gas to the boundaries of the raceways, the problem of radiant heat transfer be- tween two grey bodies forming a closed system is solved. Using the structural parameters of the furn- ace, the inlet parameters of the combination blast and exit parameters of the melt, the model permits the calculation of the temperatures of materials entering and leaving the raceways and also the res- idual temperature of the gases, which qualitatively differs from the theoretical combustion temperature. Analysis of the operation of several different blast furnaces has shown that the overall picture of the interaction between gas flow dynamics, mass and heat transfer processes occuring in the race- ways and in the zone of final product formation, obtained with the aid of the model, now permits us to approach from a different position the deter- mination of the limiting factors in furnace operat- ion. It also allows us to explain certain phenom- ena observed in blast furnace practice and to dis- cover new relationships which may be used in analy- sis and control of the smelting process.

Jan 1, 1981