Search Documents

By Hannington MD

On the southern flank of Lihir Island, a group of three volcanic cones were discovered at water depths from 1000-1500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts, and porphyritic phlogopite basalts. One of the volcanoes has a recently erupted ejecta blanket (recovery of warm ash!), containing a suite of abundant mafic to ultramafic xenoliths. These xenoliths appear to represent a unique cross-section of subduction- modified mantle material sampled by volatile-rich primary fore-arc magma during its ascent to the seafloor. The most spectacular finding was the discovery of an active hydrothermal system with associated vent fauna and mineralization at Edison Seamount, and the recovery of unusually gold-rich (up to 43 ppm Au) hydrothermal precipitates in 1050 m water depth at the top of Conical Seamount, only 25 km south of the world-class epithermal Ladolam gold deposit on Lihir. The discovery of submarine hydrothermal vents associated with highly alkaline, quartz-undersaturated fore-arc volcanics represents a significant departure from similar hydrothermal systems on the mid-ocean ridges and in back-arc basins. The high gold grades in hydrothermal precipitates at Conical Seamount may indicate the first documented example of a shallow-marine epithermal system analogous to those known on land, and has important implications for the gold potential of submarine arc environments.

Jan 1, 1995

By Toro HCH, Von Borries GH

A brief description of the semi-autogenous grinding (SAG;) facilities of Compania Minera Disputada de Las Condes is given. A data-logging and computer system was connected to the plant inter facing the existing analog control system in a supervisory s, control philosophy. The development of a control straiov,v t,) maintain maximum power of the SAG mill atsubjected to process restrictions is shownThe present control scheme is discussed inalgorithm was designed based on correlations onLween vartaoles. Associated with this, a direct level of control was developed be, on classical control algorithms, process inter-active tuning has been included. Also, an algorithm to prevent overloading of the is discussed. Control scheme tests are presented in comparison t manual operator control under the same conditions. It is shown t the control strategy gives a more stable operation and a higher plant throughput.

Jan 1, 1985

This paper reports on the field results of using electronic detonators to improve blast outcomes. OricaÆs electronic detonator, the i-konTM Digital Energy Control System, allows exact and precise timing in 1 ms increments from 0 to 15 000 ms. This gives the blast engineer and shotfirer the ability to fire a blast using any possible desired sequence. In the three years that have followed the release of the i-konTM System, Orica has been re-exploring ways of initiating blasts using the abilities of electronic detonators to improve fragmentation, diggability and crusher throughput. This study began with revisiting fundamental blast theory, lead to generation of new state of the art computer fragmentation modelling and ended with many iterative field trials of i-konTM blasts across a wide selection of mining methods and rock types. At three sites a detailed measurement process was undertaken to compare the results of pyrotechnic blasts with i-konTM blasts. This paper will detail the significant improvements in fragmentation, diggability and crusher throughput that was found at these sites.

Jan 1, 2003

By Zamora C

The performance of a system for detecting the onset of overloads on rod mills is described. The system has bee,, tested at CODELCO E1 Salvador Concentrator where, due t,, variations on size distribution of the copper ore feed, th' rod mill is frequently subject to overloads. The main inpur signal to the system is the rod mill sound, after being measured and analog conditioned. This signal and othe signals measuring the fresh ore feed and the mill watt addition are fed to a computer containing a simpl mathematical model. The model parameters are empiricall estimated and an analog output signal is generated, whic gives an early prediction of the overload condition. The experimental results described in this paper show that the overload condition may be predicted with an anticipation of about three minutes.

Jan 1, 1985

The gold deposits of Kalgoorlie are the most important on the Precambrian shield of Australia. Gold was first discovered.'-:.V. ,,.,.-,..Kalgoorlie in June, 1893, and olthough`the original find was of ;:...;;small extent, the prospecting activity which stemmed from it 'led to'the ciscovery.of the lodes of the Golden Mile, some three miles to the south. Th¬ production of thea1algoorlie fiold.a.t December 31st, 1962 was 80,556,572 tons -for -33.,853, 215 ounces of gold. Most of this production has come from the Golden Mile area anu Table 1 summarises the Gplueh Mile. production for periods which correspond approximately to the main phases of operation of the field.

Jan 1, 1964

It is indeed an honour to address the perth branch of the australian institute of mining and metallurgy and to have the opportunity to talk to you about the future role of upgraded ilmenite on t102 feedstock supply and demand. There have been many papers written on upgraded ilmenite supply and demand and now I would like to share with you QIT's view of the situation first, a word about demand, although I will be talking principally on the supply issue. The principal use of t102 is in the manufacture of pigments which, in turn, are used in paints, plastics, and the paper industry together with a few miscellaneous uses, while a further b% or so of t102 minerals are consumed for the manufacture of titanium metal and for the manufacture of welding electrodes. the total demand for contained t102 is of the order-of 3 million tons per annum, and the general consensus in the industry is that growth rates should be of the order of 2% annually- it is against this backdrop that suppliers must compete with one another and produce least cost materials for the pigment industry. At the moment, supplies are relatively tight, but the generally slow growth in demand coupled with the abundance of titanium bearing minerals should ensure that long term the reverse is generally true. Now, let us examine the supply situation. Titanium is the 9th most abundant element in the earth's crust, so the problem from the producers` point of view is not one of scarcity of titanium minerals, but of how to extract most economically t102 feedstocks from a wide variety of choices- up to the present, all titanium feedstocks are being derived from either rutile or ilmenite rutile, at about 95% t102 content, is indeed a premier raw material which does suffer from potential scarcity and rutile supplies will likely be a diminishing factor in future decades- whereas ilmenite, a combination of iron and titanium oxides found in varying ratios, may be found in huge quantities all over the world.

Jan 1, 1986

Underground mining of the ore below the West Lyell open cut commenced in 1972 with the 10 Series stopes above rail haulage level. The third lift of stoping (30 Series) com- menced this year, and access to the 40 Series stopes is being developed. The method uses transverse open stopes with subsequent mass blasting of the rib and crown pillars and consequently there is sub- sidence and caving of the old open cut area above.

Jan 1, 1982

By S Ellis, J McMullen, M Habner

A new leaching regime was implemented at Kalgoorlie Consolidated Gold MinesÆ (KCGM) Gidji plant on a cyanide leach of ultra-fine ground sulfide concentrate. High lime concentration and lead nitrate were used to overcome the refractoriness of the fine sulfides (high reactivity of fine sulfides with the presence of gold tellurides). The leach pretreatment stage was shown to be detrimental and was shut down. Lime titration was introduced as part of the process control. It was shown that the leach could be performed at low dissolved oxygen, (ie 3 - 5 ppm) to avoid sulfide oxidation and the associated high cyanide and lime consumption. Plant results showed reduced cyanide consumption (40 per cent) and an accelerated leaching rate, whereby most of the gold was dissolved in 24 hours compared to 72 hours used previously. Similar work was performed at KCGMÆs Fimiston plant, which leached a combined ultra-fine ground sulfide concentrate along with the slimes fraction from hydrocycloning the bulk flotation concentrate. The use of lead nitrate, high lime and carbon-in-leach generated a faster leaching rate and minimised adsorption of gold on fine pyrite particles. The grind, previously controlled with a P80, was replaced by a P98 to give a better operational indication of top size hydrocyclone performance. Before the implementation of the changes, average leach residues for slimes and UFG were respectively 4.0 g/t and 5.5 g/t. With the modifications to the leaching regime, average leach residues were lower by 1.5 - 2.0 g/t. Whilst significant improvements have been demonstrated, further work is progressing at KCGM to further reduce ultra-fine concentrate leach tail grades, and also to improve the understanding of concentrate refractoriness and the factors responsible for differences between laboratory and plant leach results. Estimated profits since the implementation of the new approach are in the range of $A3.5 million per year.

Jan 1, 2005

By Brockway DJ, Holmes RJ

A natural gamma-ray gauge has been devel- oped for discriminating overburden and inter- seam sediment from low ash coal located on a moving conveyor belt. It is based on the difference in natural radioactivity of the sediment and overburden compared with the low ash coal, which is detected with a highly ef- ficient "Polyscin" NaI(T1) gamma-ray detector located underneath the conveyor. Gauges have been successfully installed on the bucket wheel boom of the two coal dredgers at the Loy Yang Open Cut. They are used to warn dredger operators that they are digging overburden or sediment and that action is required to avoid the sediment or divert it to the waste dump rather than send it to the coal bunkers at the power station.

Jan 1, 1987

By I Gray

Other than being reasonably certain of the average vertical stress being lithostatic, there can be little certainty about stress in the ground. The stresses and strains in rock are a function of gravitational effects, external load, thermal changes, diagenesis and their mechanical properties including elastic, creep and post failure behaviours. It is highly desirable to measure stress where mining is going to take place, even if the virgin stress condition has already been changed by mining. The concept of some far field stress value that is more or less constant is usually invalid and can be dangerous to use in mine design. Measuring stress is not simple. The basic processes are broken into two categories, one where the rock will not fail around the borehole in which the stress is being measured and one where the rock has failed or will fail. Because of the complexity and cost in obtaining a single, precise stress measurement it is highly desirable to have some system to be able to obtain an idea of the uniformity, or otherwise of the stress situation between precise measurements. Table 1 shows the methods for measuring stress. The first five methods work on the basis of some fairly direct measurement of mechanical rock behaviour while the last three are attempts to get some idea of stress out of core long after it is removed from the host rock. While these latter methods appear to tick all the boxes for applicability there is a great deal of uncertainty in the results that they deliver. This paper reviews the methods for measuring stress and presents two new methods. These are a three dimensional overcore system to provide precise stress measurements in rocks that will not fail around the borehole and a core ovality system. The latter can be used to provide information on the stress difference orthogonal to the core. It is particularly useful because it can be used every metre of core length.

Nov 29, 2022

The purpose of this study was to investigate the effectiveness of froth fl otation for the recovery of gold from the gravity tailing stream of the former Lihir Gold Limited (LGL) operation in Ballarat. The P80 of the tailings was determined by screen analysis as 1 mm, with test work conducted on as received material along with samples ground to P80 sizes of 47, 78 and 134 microns. Laboratory scale batch flotation tests were conducted at both natural and elevated pH to investigate the impact of pyrite depression on gold recovery. Results indicated that although an increase in grade from approximately 0.7 g/t to 3 g/t was achievable at a natural pH and a P80 of 134 micron, gold recovery was low at just 35 per cent. Finer grind sizes were found to have an adverse effect on both grade and recovery. Future efforts will be focused on the sub 310 micron size fraction of the tailings, which was revealed to contain approximately 85 per cent of the available gold and may be amenable to cyanidation or ultra-fine gravity treatment.

Aug 1, 2010

By R Williams, P Godwin

In a time of changing rainfall patterns and in the light of recent tailings dam failures, there is closer environmental scrutiny for proposed tailings dam construction or expansion. Therefore the elimination of the traditional tailings dam could provide both environmental and cost benefits to an operation. One method to dewater tails is using pressure filtration to achieve lower moistures than what is currently available using other dewatering technologies. Further benefits include a higher rate of filtrate recovery, reuse of waste material and the potential for dry stacking of the filtered tailings cake, thereby minimising both risk and cost. This paper chronicles the replacement of two existing belt filter presses with a single McLanahan recessed plate filter press to dewater a tailings stream at a Bacchus Marsh site. It covers the slurry testing, equipment selection, installation, commissioning and operation of the filter press to achieve the following objectives:• removing the current tailings dam and slimes cells from the existing process to minimise failure risk and reduce the cost of a dam upgrade, as well as operational and maintenance costs• free up the surface area which was previously occupied by tailings dams and slimes cells• recover additional water to be returned to the process• reduce flocculent usage• reduce truck movements and handling.The project’s owner also expects to reduce carbon emissions by over 3000 t over the lifetime of operation as well as substantially reducing operating expenditure. By recognising the carbon reduction benefits, the project owner was able to successfully achieve partial funding through the Voluntary Waste Industry Protocol.An unanticipated, but as yet unquantifiable, bonus for the project was to seek an offtake agreement for the tailings thereby allowing the tailings to be considered a valuable source of beneficiated clay suitable for the construction industry.CITATION:Godwin, P and Williams, R, 2017. Pressure filtered tailings – environmental and cost benefits, in Proceedings MetPlant 2017, pp 324–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

Design and construction techniques used to develop two highway tunnels in inaccessible mountainous terrain are described. Measures used to adapt the design to the unusual geology and topography are discussed, as well as measures to adapt the construction methods to available equipment, materials, and skills. Sharp local variations in geoloqic conditions resulted in field modifications to both design and construction techniques. The geology is a volcanic ash and breccia-agglomerate at one site, a jointed andesite at the other, which is also the site of a major landslide. Both rock reinforcement in the form of pretensioned and grouted rock bolts with a shotcrete lining,and rock support by struc- tural steel sets with a reinforced concrete lining were used. A canyonside location and high lateral in-situ stresses required modification of design procedures. Pilot tunnels at both sites resulted in adapting the designs to site conditions with large savings in lining costs, disclosing problem areas in advance of the main excavation, and cushioning of blasting pressure to minimize stability problems.

Jan 1, 1976

By C Young

The identification of Critical Risks, their associated Critical Controls, and the implementation of processes to ensure their ongoing management can be difficult and resource intensive. Answering the following Critical Risk Management related questions can be challenging: • What is a Critical Risk? • What is a Bow-tie Analysis and when should it be used? • What is Critical Control? • How is the effectiveness of a Critical Control assured, and how is this measured? • Who is responsible for managing Critical Controls? • What are the implications if a Critical Control is not effective? It appears that in the mining industry’s efforts to implement the Critical Control Management Process outlined by the International Council on Mining and Metals (ICMM), instead of embedding an integrated, well understood, value adding process, we have instead created a resource hungry monster that is poorly understood by numerous layers of the organisation.

May 5, 2022

By R MacGillivray

The Golden Cross mine was an open-pit and underground gold and silver operation from December 1991 to April 1998. Closure of the mine has been based on an approach agreed among stakeholders. The initial phase was the release of a closure plan which was regarded as the blueprint for the following phases and the closure works required to implement the plan. The second phase involved lodgment of consent applications and their granting for the final water management configuration. The final phase is monitoring, confirmation that the site is performing as required by the closure plan and consents and settlement of final ownership, management and surety arrangements. Industry best practice modelling techniques have been used to finalise closure design and have been shown to be good predictors of site water management and discharge performance. Site discharges are in compliance with toxicology based water quality criteria for the protection of aquatic life and most discharges from the site, including those from the closed cyanide-tailings facility, can now be discharged without further active intervention or treatment.

Jan 1, 2002

Plant growth is likely to prove the most suitable and satisfactory material to stabilise and cover quarry faces and worked-out surface mining sites. The careful selection of plant species is of paramount importance to the success of any attempts to re- vegetate these sites. Various tech- niques are recommended and attention is drawn to different factors,which will adversely affect plant growth.

Jan 1, 1976

By K Osman, P Bennett

The mining of an underground orebody requires development both in waste and ore before stoping commences. Regardless of what metal is being extracted, the waste development is minimised to reduce the cost per unit of metal mined. At the Western Metals Zinc Kapok mine site, reducing the cost per tonne of lead and zinc mined is paramount. Decline waste development costs can be minimised by methods such as increased gradient or reduced drive size. Ore development will also involve some mining of waste. The degree to which waste mining can be minimised will depend on the thickness and dip of the orebody. The drive geometry will also determine the percentage of waste within the face. It is by mining methods such as resue mining that selective mining may be used to maximise the amount of metal mined and reduce waste dilution. Resue mining can be used around a set of selection criteria established by the mine site. These selection criteria will determine how resue mining can be applied to the mine site. Selection criteria include firing times, number of headings available, acceptance criteria for percentage lost metal, dilution and most importantly operator acceptance. The single pass or two pass resue mining method should be chosen depending on the site acceptance criteria and selection criteria. The Western Metals Zinc Kapok mine site has established a set of parameters which accept the two pass resue mining method for the mining of the ore drives. The blasting results from a single pass resue method were reviewed during more recent trials in a single heading. Through a comparison of results, the parameters allowed the decision to determine the applicability of resue mining and its current form to Kapok. This paper outlines the parameters set by the Kapok mine site, reviews these in relation to the two forms of resue mining and examines the criteria which make this mining method applicable for Western Metals Zinc.

Jan 1, 2002

By J Lainé, M Badawi, A C. de Araujo, Y Foucaud, C Veloso

Flotation is the one of the most used techniques for the mineral separation of non-ferrous ores worldwide. However, the increase of the complexness along with the decrease of ores liberation sizes ought to become important challenges for mineral processing, including flotation. It now appears necessary to better understand the fundamentals of the flotation process, particularly the adsorption of flotation reagents at the liquid/mineral interfaces, to propose further improvements. Flotation relies on different phenomena: surfactants adsorption, on one hand, and collision, adhesion, and transport of particles with bubbles, on the other hand. For acknowledging the reagents adsorption mechanisms, molecular modelling tools borrowed from chemical and material sciences, are increasingly used. Atomistic simulations were successfully applied to study the flotation reagents interaction with various mineral surfaces, eg of two common minerals from iron ores, kaolinite, and magnetite surfaces, or with fluorite surface, a tungsten ores common gangue mineral.

Aug 24, 2022

By S Pontual

The use of spectral data has traditionally been for obtaining mineral information and for mapping out alteration systems. The output from these data is typically in the form of mineral assemblages and data on relative proportions of minerals. However there is much more than just mineral information in the spectral data. Most importantly, the data allow the user to obtain vital information on mineral chemistry for some key alteration minerals. The mineral chemistry data allow the users to evaluate multiple phases of alteration of the same key mineral species, and to assess which phase is related to mineralisation. Mineral indices can be extracted from the spectral data and plotted to represent variations in the chemistry and relative proportions of key mineral phases as downhole, section and three-dimensional (3D) plots. These data can also be compared with the spatial distribution of the mineralisation by integration with geochemical and logging data. Through spatial and statistical evaluation the mineral information obtained using spectral analysis can provide vital information to assist in building alteration models and therefore improve targeting for further drilling and exploration.

Aug 22, 2011

By D J. Williams, G W. Wilson, S, A B. Tran

A comprehensive field program was implemented to evaluate the internal structure and hydrology of two full-scale waste rock piles. The excavation of waste rock dumps for in-pit disposal at the two mine sites provided an opportunity to characterise the in situ properties of the dumps given contrasting geologic and climatic settings. The internal structure and materials within the dumps were observed and sampled as the waste rock piles were being excavated and placed in the open pits for permanent closure. The field program was designed to fully characterise the structure and material properties of the waste rock. The alteration of the material by physical and chemical weathering was also observed. Samples were analysed for paste pH, water content, grain size distribution and geochemistry. In situ density and matric suction were also measured. Soil water characteristic curves and saturated hydraulic conductivity were measured for representative materials. These properties were used to predict seepage pathways through the waste rock and the resulting outflow geochemistry using the finite element model SEEP/W. The materials in the dump at Site 1 were predominantly fine-grained in texture and highly weathered. The presence of dipping beds with alternating coarse and fine materials was evident throughout the profile of the dump. The structure of the waste rock appears to have an impact on the hydrologic pathways within the waste rock pile. The material in the dump at Site 2 was found to be competent and resistant to particle size breakdown. The particles range in size from clay size to large boulders with the median particle size being approximately 125 mm in diameter. The coarse-grained texture of the waste rock resulted in a loosely packed arrangement of coarse particles with little matrix material infilling the pore spaces between the coarse-grained particles. Seepage modelling for Site 1 was completed to predict seepage paths based on observed structure and hydraulic properties measured in the laboratory. The modelling showed that materials with a fine grain size distribution become the dominant pathways for flow through the waste rock pile. The modelling also showed that layers with high silt and sand contents are subject to the highest flow rates. Finer grained clay rich layers have a low hydraulic conductivity and do not convey large volumes of water. Alternately, coarse gravel and cobble materials are unsaturated under values of matric suction that approach the residual water content of the material and do not transmit liquid water. The seepage modelling together with the results of the geochemical analysis show that the dominant particle size that receives the most fluid flow and flushing ranges from fine sand to silt, corresponding to materials with air entry values ranging between 5 kPa to 50 kPa.

Jan 1, 2003