Search Documents

By H Ishikawa, S Palaniandy

The gravity-induced stirred mill such as the TowerMill is an energy-efficient grinding solution used in secondary, tertiary, and regrinding duties in the mineral processing concentrator. The interest in this technology is emerging, with more than 300 mills installed globally in various grinding duties and commodities for the last 30 years. Although the technology is matured, there are still opportunities for improvement and the development of new knowledge to improve its circuit energy efficiency and reduce water consumption. Recent studies show that a combination of stress intensity, ore hardness, slurry density, and mill feed configuration can be used to evaluate the performance of the grinding circuit. A recent pilot-scale TowerMill test work at various stress intensities shows that a lower operating work index and size-specific energy were achieved at higher agitator tip speed and using medium size grinding media. These outcomes were confirmed through several site trials. A smaller 17 mm grinding media has reduced the operating work index and size-specific energy by 18 per cent and 11 per cent, respectively, compared to the 20 mm in a magnetite concentrator. Moreover, the conversion from top feed to bottom feed configuration has reduced the operating work index and size-specific energy by 13 per cent and 37 per cent, respectively. The circulating load was reduced by 34–38 per cent, leading to a reduction in the dilution water consumption in the hydrocyclone feed sump by 20 per cent. A variable frequency drive offers flexibility to change the stress intensities on the TowerMill, where a 35 per cent reduction in specific energy was achieved when the ore became soft. This paper explores the potential design and operating strategies that can be implemented to enhance the energy efficiency, reduce water consumption and reduce CO2 emissions in the circuit and finally evaluate its impact on the total cost of ownership.

Aug 24, 2022

By E Wargem

The conventional method of underground mining involves a process known as drilling and blasting to excavate valuable ore bearing minerals through the load and haul process. Drilling and blasting processes are completed for both the development of the tunnels used to access the orebody and for mining out the orebody itself. The former being called development drilling and blasting, and the latter production drilling and blasting. In either development or production drilling and blasting, the effective recovery will be largely reliant on the extraction of the initial void created in each blast cycle. In development tunnelling, the initial void is commonly known as a Burn Cut. The initial void created in production drilling and blasting has many names such as a Slot, Winze, Rise or Raise. There are drill patterns and charge designs used to create these initial voids in the production cycle. This paper discusses common slot or winze designs for production drilling and blasting; and various critical design criteria for these. The document also aims to provide a process for completing desktop reviews of current patterns employed on-sites and provides an initial guide in a process for improving the recovery of a slot, winze, rise or raise in underground mines.

Mar 29, 2023

By Rowe P, Rogers D, Warren M

Pressure cyanidation of the minus 10 micron slimes fraction of the Fimiston flotation concentrates for the recovery of gold values has been evaluated as an alternative processing route to the roasting and atmospheric cyanide leaching of the calcine. Laboratory and pilot trials have demonstrated that gold extractions of greater than 94 per cent can be achieved at cyanide consumptions of 12-24 kg/t and oxygen consumptions of 0.1-0.3 Nm3/t with total pressures of 1000-2000 kPa. Economic and operational assessment of several reactor configurations suggests autoclaves may be preferred over pipe reactors at treatment rates of 10 t concentrate/h.

Jan 1, 1996

By R N. Humphries

The aim of this paper is to question the need to develop bespoke monitoring and assessment methodologies and criteria, thereby ‘reinventing the wheel’, when designing and assessing the success of important natural habitat and ecosystem restoration schemes at mine sites in the UK and Australia. It draws attention to the existence and applicability of the Phase I Habitat, National Vegetation Classification (NVC) and Condition Monitoring methods in the UK and similar approaches used in Australia. These are long accepted established methodologies and have published accounts for describing, assessing and managing natural vegetation communities, habitats and ecosystems. They are often used at the environmental impact stage, but seemingly rarely, if at all, in restoration design and management at mine closure. Their application to mine restoration and closure is illustrated and discussed by reference to a surface coalmine in South Wales, UK.It is concluded that the application of a combination of the Phase I Habitat, NVC and Condition Monitoring methods is highly relevant to the expectations of the Convention on Biological Diversity (CBD) and its implementation in the UK, and probably in Australia too. The methodology and criteria described could be incorporated into the guidance and specified in the mining permits so that there is clarity as to the expectations and requirements for monitoring and assessment for bond release. Their use could be of wider application where there is a requirement to assess the success of restored CBD assets and ecosystems.CITATION:Humphries, R N, 2014. Why reinvent the wheel when there are established methodologies to aid the design and assessment of restored natural ecosystems on mined land?, in Proceedings Life-of-Mine 2014 , pp 675–692 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M I. Pownceby, M A. Rhamdhani, S Palanisamy, D Fellicia, B Satritama, G A. Brooks, A Ang

Metal production have long been using carbon sources as both reducing agents and energy sources. Consequently, the global extractive metal sector contributes significantly to greenhouse gas emissions, accounting for approximately 9.5 per cent. Hydrogen gas offers as a promising ecofriendly alternative to carbon in metallurgical processes, serving as both a reductant and energy supplier with a by-product being only water vapour. However, the implementation of molecular hydrogen faces certain challenges related to the thermodynamics and kinetics of metal oxide reduction. In addressing these challenges, researchers have explored the application of hydrogen plasma, generated by subjecting molecular hydrogen to high energy to produce atomic, ionic and excited hydrogen species. Hydrogen plasma offers thermodynamic and kinetic advantages over molecular hydrogen and carbon-based reductants, exhibiting lower standard Gibbs free energy of reaction and activation energy. Therefore, hydrogen plasma can produce metal in fewer steps, process any oxide feed and feed size and even be used to refine metals. Despite these advantages, challenges exist in utilising hydrogen plasma in extractive metallurgy, including electricity costs, potential reverse reactions and industrial-scale implementation. This study provides a mini review of prior research on hydrogen plasma for metal oxides reduction, particularly iron oxide, as well as state-of-the-art techniques for its use in extractive metallurgy applications by mentioning several reactor types. Future prospects and scale-up possibilities of the hydrogen plasma in extractive metallurgy will also be presented.

Aug 21, 2024

By G S. Beros, K M. Edwards

Over the past 20 years drum scrubbers have become a widely adopted technology within iron ore beneficiation plants. Generally, the drum scrubbers in use are considered high-capacity machines capable of accepting larger-sized feed material. Together with a water addition to a desired pulp density and a mild energy input, these large rotating machines effect an attritioning action that removes water soluble clays and other deleterious materials. Within the Western Australian iron ore industry, drum scrubbers have been successfully applied to Channel Iron, Marra Mamba, Bedded and Detrital orebodies. The introduction of drum scrubbers has enabled Western Australian producers to satisfy the substantial increase in demand for iron ore from Chinese steelmakers by making the lower-grade sections of the above orebodies economic. However, despite being a relatively simple unit process, the requirements for successful design and operation of these machines are not fully understood. This paper draws on the collective experience of both authors to provide some points to consider for incorporating drum scrubbers into iron ore beneficiation plant flow sheets.

Sep 18, 2023

By R McIlwraith, B Breul

"This paper discusses the successful use of bituminous geomembranes (BGMs) in mining applications since their development in 1974. It explains and illustrates the structure of a BGM composite, which is a geomembrane manufactured by impregnating a polyester geotextile with a compound of bitumen, elastomer and filler. Examples of applications of BGMs in the mining industry are also presented in the following contexts.Storage of solid waste: storage of mining waste at mines in Canada heap leach pads in France, Peru, Chile and Turkey at the base of a mining waste landfill in Brazil capping of solid mining waste in Chile and Canada temporary capping of mining stockpiles in Australia (with possible reuse of the BGM for other works).Examples of the application of BGMs for the storage of liquid waste in mining containment reservoirs in Canada, Guatemala and Peru will also be given.For each example given, reasons are supplied that supported the choice of BGMs by the clients and consultants, drawn from the following advantages of the BGM:BGMs have excellent puncture strength, due to the internal polyester reinforcement, as well as excellent ultraviolet resistance. This often eliminates the need for a cushion geotextile or cover soil over the BGM.BGMs have a very long life expectancy, in excess of 300 years, in subsoil conditions (Breul et al, 2004).BGMs can be installed in very harsh climatic conditions. They are suitable for high wind environments as their heavy mass per square metre makes them resistant to wind uplift. The low coefficient of thermal expansion means that BGMs are suitable for installation in mines where very low or very high temperatures are expected. This reduces construction delays and allows for a quicker use of the mining facility.The fact that the BGM can be installed by the mine’s own workforce, after appropriate training from the BGM manufacturer, allows for a more flexible construction sequence on the mine.Ability of the BGM to connect to other materials such as concrete, steel, rock and other geomembranes that may be on the mine site.The technical advantages of a BGM enabled the engineering consultants to prepare solutions for their mining clients that had a lower environmental risk, had a faster completion schedule and were overall a cheaper option than with a polymeric geomembrane.CITATION:Breul, B and McIlwraith, R, 2015. Bituminous geomembranes in mine construction, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By A Ross, B De Rivaz

The results of full-scale tests on precast segment made at University of Roma are presented. The segments were cast using fibre-reinforced concrete produced without any traditional reinforcement, by using fiber made in high-strength steel and a new type of anchorage.Bending tests were performed in order to check the bearing capacity of the segments under the flexural actions; these occur during de-moulding, handling, storage phases as well as in the in situ condition (due to asymmetric soil pressure). Furthermore, point load tests simulating the TBM thrust were performed, in order to study the construction phase (excavation).The results show that the segment response largely respects the material testing and design advice according to the Fib Model Code 2010. Providing engineers, precast operators and builders confidence in material strengths and design methodology.CITATION:De Rivaz, B and Ross, A, 2014. Full-scale tests on precast tunnel segments made in concrete reinforced with high-strength steel fibres, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 469–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By B Klein

This paper stems from research and development in sensor and sorting technologies towards future sustainable mining undertaken by the UBC Mine-Mill Integration group in collaboration with MineSense Ltd. Sensors and sensor-based technologies such as ore telemetry and sorting are envisioned to be a significant component in achieving such ‘invisible’ future sustainable mining. Such technologies offer high flexibility and power in use: delivering valuable information from the very preliminary stages of mining exploration through to final upgrading of the ore preceding the fine comminution stages. This paper reviews sensors and sorting as enabling technologies towards a future smart mining operation and introduces a model in which sensor-based exploration (down-the-hole sensing), ore exploitation (smart-shovels), transportation (smart-conveyors) and preconcentration (sensor-based sorters) are effectively integrated to increase the present value of operations. It is anticipated on the basis of several case studies that an effective use of sensor technologies through tomorrow’s ‘smart mine model’ should lead to several positive impacts ranging from increased mining production, to reductions in transport costs, overall energy use and waste generation. In this way sensors can be used to maximise the profitability and present value of the mining operation from the exploration stage through to mine closure.

Nov 22, 2011

By X Li, W McKeague, M S. Powell

This paper explores the importance of operators in the overall efficiency of mineral processing plants. With the potential of future control configurations becoming more remote, it is time to review the implementation of control and utilisation of operators. This paper is based on a preliminary review of operators and control room operations and clearly shows that, in the minerals industry, operations are typically run in a reactive mode (with a focus on ensuring equipment operation), rather than in a proactive mode (with a focus on optimising the process performance). The primary reason for this misguided approach is the short sighted thinking applied to the challenges of designing technology and organisational tools capable of addressing the essential operational needs: an approach which inevitably results in a disconnect between people and technology. Contrary to the popular approach of replacing operators with expert systems, the thesis of this paper is that the shift to more complex circuits, with higher demands on processing capability and control, will require the actual upskilling of operators. Experience in mineral processing and other industries indicates that expert systems cope well with small changes but are typically unable to respond to major changes in feed material and this is where the expert operator becomes crucial. Providing operators with ongoing high level training in process understanding, and restructuring how they interact with the plant and interface with the control system is the approach being proposed here - an approach surprisingly underutilised and often absent in the minerals industry today.CITATION:Li, X, Powell, M S and McKeague, W, 2012. Unlocking processing potential by empowering our operators, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 333-340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A M. Nyembwe, A M. Garbers-Craig, R Cromarty

With the depletion of high-grade lump iron ore, concentrates have been identified as an alternative material for sinter making. Adding concentrates to the sinter mixture reduces sinter bed porosity and gas flow through the sinter bed. This will result in lower sinter strand productivity. A potential solution to this problem is to add concentrate in the form of micropellets. This study investigates the effect of concentrate and micropellet additions on the permeability of the sinter mixture. Permeability was measured on sinter mixtures containing ten to 40 per cent concentrates and micropellets at various moisture contents. The effect of concentrate and micropellet addition on the permeability–moisture relationship was examined. The results confirmed that the addition of concentrates into the sinter mix decreases the maximum permeability of the sinter bed. The incorporation of micropellets into the sinter mix reduced the permeability less than concentrate addition. The study also showed that the maximum permeability of sinter mixes containing concentrate is reached at the same moisture content as the sinter mixture without concentrate addition. For sinter mixes containing micropellets, additional water must be added to obtain maximum permeability. Parameters including the granule size, void fraction and angle of repose were also investigated to evaluate their effects on the sinter bed permeability.CITATION:Nyembwe, A M, Cromarty, R and Garbers-Craig, A M, 2015. Effect of concentrate and micropellet addition on iron ore sinter bed permeability, in Proceedings Iron Ore 2015, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C J. Greet, S Jacques

In most instances, the application of high-chrome grinding media results in an increase in the recovery of the valuable mineral(s). The authors have published data from a number of plant-based case studies, which indicate that it is not unreasonable to expect a recovery increase in the vicinity of 1.5 to 2.0 per cent for a copper ore. It is of interest to understand where the increase in recovery is coming from. That is, is the additional copper recovery the result of improved fine particle flotation or is it due to an improvement across all size fractions?This paper aims to answer this question. Laboratory flotation tests were completed using forged steel and a high-chrome alloy on a volcanogenic massive sulfide copper ore. The unsized data indicated that the application of high-chrome grinding media to this ore resulted in an improvement in both copper recovery and copper concentrate grade. A detailed kinetic analysis of both the copper sulfide and gangue minerals was completed that clearly shows that the change to a more inert grinding media produced significant increases in the flotation rate constants (both fast and slow) across all size fractions. It is also possible to observe that the change in pulp chemistry has resulted in a decrease in the flotation kinetics of the -20 micron pyrite, while the coarse pyrite recoveries have increased, presumably because of an increase in the flotation of the chalcopyrite/pyrite composite particles.CITATION:Greet, C J, Jacques, S and Kinal, J, 2014. Recovery-by-size kinetic analysis to determine where metallurgical improvements occur when converting to high-chrome grinding media, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By T Ireland

The Project Hobson tunnel excavation was the first use in New Zealand of an earth pressure balance (EPB) tunnel boring machine (TBM). The tunnelling on the project was very successful and break-through was achieved three weeks ahead of program, demonstrating that tunnelling can be undertaken in Auckland with a high degree of cost certainty.Project Hobson involved the replacement of an existing 90 year old above ground sewer that crosses Hobson Bay in Auckland, New Zealand, and which had reached the end of its economic life, with a 3 km long, 3.7 m internal diameter segmentally lined bored tunnel. The NZD$ 118 M project has provided several environmental benefi ts to the Owner, Watercare Services Ltd and the local community:· provide capacity to meet projected growth in the region,· virtually eliminate wastewater overflows into Hobson Bay and the Waitemata Harbour, and· remove an obtrusive visual feature and open up the bay for recreational purposes.Auckland’s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20 km of the city centre.The paper describes the design and construction challenges for the projects, including TBM performance, ‘sticky spoil’ management, and risks associated with basalt lava flows and two paleovalleys. The paper also highlights the reasons for the success of the project, including a rigorous approach to risk management during design, and effective planning during construction. Other useful data such as the effect on the watertable caused by closed face tunnelling, and ‘faceloss’ estimates derived from settlement arrays are included in the paper.Project Hobson also saw the successful implementation of a Geotechnical Baseline Report – one of the first uses of this type of document in Australasia.

Mar 8, 2011

By O A. Aladejebi, S Mitra, T Singh, D O’Dea, S, T Honey

Granulation of the iron ore blend and the additives is the foremost step in the agglomeration of iron ore fines to achieve a permeable bed during sintering, which is crucial for sinter productivity. This study investigated the granulation of four types of blends to determine the impact of granulation on bed permeability. The blends were granulated in a rotating drum at various moisture contents and their JPU permeability was measured at each moisture content in a permeability pot (diameter 95 mm and height 500 mm) at various flow rates. Several independent experiments were carried out to investigate the changes in permeability when mixtures of different particle size range (-1 mm and +1 mm) were introduced into a packed bed with a larger particle size range (-6.3 mm to +4.0 mm). The results revealed that the addition of particles in the -1 mm size range had a more pronounced negative impact on permeability compared to particles in the +1 mm size range. This can be attributed to the relatively higher energy losses (mainly inertial) associated with the presence of -1 mm particles in the mixture. The findings were used to quantify the granulation process based on the -1 mm particle size fraction in the granulated mix and their utilisation (denoted by UI-1 mm). For achieving optimal permeability in a specific blend, it was found that a UI-1 mm (utility index of -1 mm particle size) ranging from 0.82 to 0.92 was required. However, exceeding a UI-1 mm value of 0.95 resulted in weaker granules prone to deformation and led to decreased bed permeability. The study also showed that the UI-1 mm was highly dependent on the water addition per kg of -1 mm in dry feed and suggested adding ~80 to 110 mL of water per kg of -1 mm in dry feed to attain the best possible permeability. Additionally, the research proposed a mechanism involving the melting of granules at high temperatures and highlighted the influence of -1 mm particles on bed permeability during the sintering process.

Sep 18, 2023

By S Szylkarski, D N. Graham

In mining, water management is an operational necessity, requiring planning and detailed engineering, as well as risk assessment. Yet, the hydrology of streams and aquifers typically extends well beyond the boundaries of mine operations and intersect with environmental and social values. Mine managers often plan, design and assess the impact of water management activities (such as dewatering, excess water disposal and flood management) with a mine site or process specific focus. The challenge is that the impacts are spatial, long-term and complex – and may be cumulative across multiple mine sites. Further, there is usually little consideration of the feedbacks and interactions between surface water, groundwater and catchment hydrology. Failure to understand these processes can lead to poor decisions and increased costs. This presentation outlines an approach to simulating integrated hydrology in mining catchments that addresses the shortcomings of traditional modelling techniques.CITATION:Graham, D N and Szylkarski, S, 2016. Simulating integrated hydrology in mining catchments from planning to closure, in Proceedings Life-of-Mine 2016 Conference, pp 101–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

Risk management has become an essential tool for mining companies to ensure their projects are well-managed and profit expectations are achieved. Risk management has also become a mandatory corporate governance requirement in Australia for publicly listed companies and equally important to attract investors. This paper provides a brief overview of the essential tools needed to implement a practical risk management framework to comply with the internationally recognised ISO 31000:2009 risk management-principles and guidelines from the perspective of small or soon to be producing mining companies. To?successfully?deal with the unknown and to manage the opportunities and risks involved with a mining project requires a clear understanding of the basic risk management principles. These include how to develop a project risk register, how to develop a project risk treatment plan and how to manage and monitor project risks to take full advantage of the opportunities presented.The first step is to identify and fully appreciate the risks that face a mining project. There are many risk identification methods that can be used including checklists, brainstorming and hazard and operability (HAZOP) studies. These often lead to a telephone book full of risks which are near to impossible to manage. A risk library specifically designed?for mining?projects containing no more than 100 risks will cover the major showstoppers, is practical and can be readily implemented and successfully managed.A risk framework also needs to be established which is compatible with the companyÆs structure and objectives. Once each risk has been assessed in regard to consequence and likelihood and the risk control systems are in place they need to be assigned to the responsible manager. The extreme or high risks will require a risk treatment plan to be developed. Risks will change during the life cycle of a mining project. Hence, a reliable monitoring system is also required for compliance.CITATION:Jones, J A, 2012. Mine project risk management, in Proceedings Project Evaluation 2012 , pp 117-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By S Benson

Staurolite is one of the major contaminant minerals contained in the Tiwest Cooljarloo orebodies. Approximately 80 per cent of staurolite in mined ore, reports to the heavy mineral concentrate that is supplied to the Dry Mill. Staurolite in heavy mineral concentrate is typically five per cent by weight and has no significant effect in the Dry Mill other than to occupy equipment space, reporting as a tailing, that requires transportation and disposal back to the mine site. Staurolite is an aluminosilicate with a MohÆs hardness of 7.5. It is known to have potential as an abrasive blast agent and it is produced in substantial quantities in the USA for that purpose. Research indicated that there was potentially a market for staurolite within Australia, as a replacement for some of the lower grade abrasives as well as a material of choice. A small tonnage of staurolite product was manufactured through a simple circuit within the Dry Mill in December 1998. This was subjected to industrial scale tests by external companies specialising in sand blasting. The most significant batch of tests were conducted at the Tiwest Chandala site on plant and equipment undergoing corrosion repairs. Staurolite was tested against three other commercially available abrasives and compared very well with respect to surface profile, surface texture, coating adhesive strength and dust generation. As part of a due diligence study, free silica, radiation and heavy metals contents of spent abrasive and dust was investigated. This information was needed to seek approval from the appropriate Western Australian statutory authorities to sell staurolite as a product. Approval was received in November 1999. Tiwest has since installed a production circuit in the Dry Mill capable of producing 20 000 tpa of Staurolite.

Jan 1, 2001

By B Wu, C Zhao, B Lei

At present, the friction factor is calculated by measuring pressure drop and airway configurations. However, the workload of on-site measurement is heavy, and the measurement results are easily disturbed by the external environment. In order to meet the need of intelligent ventilation to quickly and accurately obtain the friction resistance of roadway. Based on the important of roughness in Atkinson friction resistance formula, in this paper, fractal theory is used to characterise the 3D rough surface, and a method based on fractal dimension to describe the roughness of roadway surface and calculate the friction resistance was proposed. A computational model of friction resistance for fractal characterisation of roadway 3D rough surface was established. The parameters of the model were deduced and verified by using Nikuradse experimental data. The fractal dimension of roadway surface was calculated by 3D laser scanning data of Kailuan roadway, the established friction resistance calculation method was compared with the field resistance measurement results. It is considered that the calculation method of friction resistance based on fractal theory is reliable and can well represent the influence of 3D rough surface characteristics of roadway. The result show that the new established friction resistance formula compared with the traditional Atkinson formula in Nikuradse experimental, the average relative error is 6.874 per cent, and compared with the measured results of ventilation resistance in Kailuan experimental roadway, the relative error is 6.667 per cent. Comprehensive evaluation and analysis suggest that the new formula can well reflect the influence of 3D rough surface on friction resistance, combined with 3D laser scanning technology, the friction resistance of roadway can be calculated quickly and accurately. This research provided a reference for the key technology and theoretical development of intelligent ventilation parameter measurement.

Oct 12, 2022

By J Wheeler

The objective of this paper is to examine the operation of high frequency screens in closed circuit grinding, where the outcomes achieved indicate favourable economic gains at the comminution stage and downstream processes, including flotation, dewatering, and filtration operations. The classification process in grinding circuits has been slowly evolving within the last century. The history of classification devices brings to mind rake classifiers and spiral classifiers, which although having higher efficiencies compared to hydrocyclones, were not able to keep pace with the evolution of concentrator equipment treating higher tonnages. This higher tonnage throughput has tended to drive the concept of utilising hydrocyclones as the classification stage in closed grinding circuits. The comminution process is commonly the most energy intensive stage of mineral processing. Researchers have determined that the classification stage in the comminution process has the greatest potential for improvement. This paper is intended to inform mineral process engineers of the benefits that high frequency screens offer over hydrocyclones. This will be done by reviewing the purpose for the evolution of classification in the comminution process, documenting past and recent studies, and explaining the modern technology that is currently available.

Aug 8, 2011

By J R. Taylor, J A. Muchan, S M. Pape, B S. Davis

Acid and metalliferous drainage (AMD) is routinely derived from waste rock, tailings, pit wall rock, underground mine voids, heap leach pads, ore stockpiles, concentrate stockpiles and even slag piles. In many jurisdictions, there is an assumption that tailings materials represent the highest AMD risk. This is likely due to their highly sulfidic and ultra-fine grained nature, and the fact that they occur in large tonnage, partially unsaturated deposits. These characteristics are not unreasonably associated with reactive and therefore highly polluting mine waste materials. Interestingly, however, the high sulfide content and highly reactive nature of tailings achieves the rapid consumption of oxygen in tailings pore spaces. This oxygen depletion can limit or halt sulfide oxidation throughout much of the tailings pile. Oxygen can only be resupplied to the tailings via atmospheric exchange at the air-tailings interface. The grain size of most tailings materials limits this resupply to a diffusion related process that only affects the uppermost 100–2000 mm. Hence sulfide oxidation in tailings can be inherently self-limiting. Unfortunately, the same cannot be concluded for waste rock materials.Using a unique site assessment strategy that focuses on quantifying acidity fluxes from various domains at a mine site, it has become increasingly evident that sulfidic waste rock produces the majority (typically 60–80 per cent) of the soluble acid and metalliferous pollution at most active and decommissioned sulfide-bearing mine sites. Whether sulfidic waste rock is disposed in engineered above ground facilities, backfilled into pits or even underground voids, it remains the primary source of pollutants for decades to centuries.Conventional end-dumping waste rock practices result in angle-of-repose pathways for air and water, and these internal fabrics exacerbate sulfide oxidation (ie pollution generation) and discharge from waste rock materials. The primary aim of many cover systems is to retard the access of air and water to these conduits. Recent thinking is that more emphasis needs to be directed at strategic waste rock pile construction practices, and less reliance placed on thin soil cover systems to prevent AMD.Waste rock pile construction approaches that minimise porosity and permeability but raise the retained moisture content and enhance water residence times have the potential to lower sulfide oxidation rates and thereby improve water quality outcomes. For example, innovative base-up, layered and compacted (BULC) waste rock piles have the potential to avoid or minimise the generation of AMD, supersede the need for treatment and facilitate successful closure and relinquishment across the mining sector (Figure 1).CITATION:Taylor, J R, Pape, S M, Davis, B S and Muchan, J A, 2016. Waste rock pile construction to lower closure and relinquishment costs, in Proceedings Life-of-Mine 2016 Conference, pp 97–99 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016