Search Documents

By A. Stanley, J. C. Mead

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus % in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9 1/2 in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9 1/2 in. bed sinters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite recovery). These tests have proved successful in increasing ilmenite recovery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was plus from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950

By M. S. Azun

M.S. Azun I have many objections to the content of the author's paper. Before discussing it, however, I would like to repeat the property of semivariogram function. Second order stationary properties of regionalized variables (ReV's) such as semivariogram function ?(h) are perfectly known in geostatistics. Also, the kriging equations in the language of mathematical statistics using second order stationary properties are well understood. However, the way to use the sample (estimated) semivariogram function in any one of the kriging procedures is vague. The sample semivariogram function is given as follows: [1 N-hy*(h) = 2(N h) i21 {Xi-Xi+h}Z, h=0, 1, N-1] where N is the total number of samples, Xi is the sample value at the i - th location, X i+h is the sample value at the i +h - th location, and h is the distance among the samples. An estimation variance of sample semivariogram function of first lag is smaller than that of higher order lag. The theoretical semivariogram function reaches the variance of samples asymptotically. But this is not easily observable because of the larger variation involved in the estimate of semivariogram function. In general, an estimation procedure is done for h = 0, 1, 2,…., up to the greatest integer less than N/2, even though sample semivariogram function can be computable through N-1. After estimating semivariogram function, the critical question of how to model sample semivariogram function arises. As seen in the above equation, sample semivariogram function is discrete and can be smoothed by the model being selected. Therefore, modeling of sample semivariogram function is the most important step in geostatistics. It not only smoothes a discrete function but also affects the results of the kriging procedure. When the only aim is to model the semivariogram function, which is the basic point of the author's paper, one can employ any fitting techniques, such as curve fitting, or any ar¬bitrary functions, which are called submodels in the paper. The term "arbitrary function" is used rather than "submodel" because there is no basic understanding of developing them. The author suggests that the sum of those submodels can also be used for the modeling of sample semivariogram function. The combination of any arbitrary functions brings many problems instead of giving an insight of the domain structure considered. The author used two arbitrary functions and the nugget effect in response to sample semivariogram function (Fig. 10). For the same example, he stated that the parameters involved in the mixed arbitrary function model can be accepted when the discrepancy between sample semivariogram function and the model is small visually. For verifying the fitting behavior of any selected model, one should not be contented with the visual satisfactory. Some statistical measure such as goodness of fit has to be used. The author's practice is no more than an exercise in curve fitting without any fundamental understanding or conceptualization of the underlying physical mechanism. Furthermore, the selection of any model is not an easy task if the purpose is the search for the "best" response to the observed second order properties of ReV's. I suggest that the Markovian model (Azun, 1983), on the basis of a theoretical understanding of underlying mechanism, which gives more information about the occurrence of regionalized variables, is used to respond all properties of ReV's. There are a lot of problems for modeling of onedimensional sample semivariogram function. Thus, it is not appropriate to go to higher order dimensional sample semivariogram function modeling. In the meantime, I would recommend that one can connect the values of standardized sample semivariogram function rather than simple values of semivariogram function in the two-dimensional estimation. The standardized values can be computed in dividing the semivariogram function value by the number of sample pairs involved in each lag regardless of the directions. In conclusion, geostatistics is an interdisciplinary area in mining that uses the principles of mathematical statistics. Thus, it should not violate any probabilistic and statistical rules. When Matheron was developing the theory of geostatistical study in the early years of geostatistics, many mining people had a reservation accepting the geostatistical tools. However, this does not mean that we, the geostatisticians, might try to convince those people using some "strange" tools or rules as some authors implied (Baafi and Kim, 1984). Instead, we have to develop and explain the geostatistical tools staying only in the framework of statistical concepts and properties. ? References Azun, M.S., 1983, "Stochastic Process Modeling of Spatially Distributed Geostatistical Data," Columbia University, Ph.D. Thesis. Baafi, E.Y., and Kim, Y.C., 1984, "Discussion - Comparison of Different Ore Reserve Estimation Methods Using Conditional Simulation," Mining Engineering, Vol. 36, No. 3, p. 280. Reply by J.M. Rendu The interactive method proposed by Rendu allows practitioners to develop semivariogram models that take into account not only the numerical information obtained by sampling, but also highly significant additional information that often cannot be quantified. The geology of the deposit - including hypotheses concerning its genesis, sampling methods, assaying methods, and mathematical methods used to calculate the semivariograms - all have an influence on the numerical results obtained and on how these results should be interpreted. If all the information concerning the spatial distribution of values in a mineral deposit was contained in the sample values, it could be argued that statistical techniques alone would produce optimum models. However, this is rarely, if ever, the case. Methods that allow the user to take into account his experience and his geologic understanding of the deposit should not be rejected for the sake of theoretical statistical purity. ?

Jan 1, 1986

By A. F. Meger

Coal treatment by oil spraying receives special attention at the Georgetown plant for the dividends it pays in satisfying present customers and attracting new markets. Customer satisfaction requires care, quality control, and use of suitable oils. REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal CO. who have helped develop, over a number of years, an efficient and flexible method for spraying controlled amounts of oil on coal. Since the Georgetown preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage. The graph, Fig. 1, shows results of the original tests made with a 700-sec residual blend and a 500-sec lubricating oil on Georgetown stoker coal of 1¼x3/8-in. size.* The advantages of better price, improperly blended can raise havoc. Some.,pale oils also, although odorless when delivered, give off a sweet sickening odor when atomized under pressure. It is recommended that all products be tested before they are used. There is a specific place for all spraying oils. For example, at a power plant a severe dust condition exists around the stockpile area and in parts of the plant. The cheapest spraying oil made, regardless of odor, will do an excellent job in this case and will save the company 3 to 5c per gal or more. Domestic trade, on the other hand, must be carefully handled to prevent complaints about odor, and the only way to do this is to stay with the proved products after the odor tests have been made. The preparation plant at Georgetown has facilities to handle either tank car or tank truck deliveries. Steam is available at the unloading point if the weather is severe, and there is an indicator at the unloading point to prevent overflowing the 20,000-gal underground storage tank. Systematic test samples are removed from each delivery and sent to the lubrication engineer to insure quality control. Fig. 3 illustrates the chutes in which smaller sizes of coal are treated. Fig. 4 shows the entire spraying system. Buried in the ground is a 20,000-gal tank with immersion heaters grouped around the feeder line to insure adequate gravity flow to the pump under all conditions of weather. Oil flows to a 500-gal preheating tank where the temperature is kept about 150°F by six 1½-kw immersion heaters thermostatically controlled. Hot oil is fed through a self-cleaning disc-type filter to the hydraulic pump. Valves and piping make it possible to transfer oil from one tank to another or to drain the lines for maintenance purposes. All this equipment is below ground level in a covered pump room,

Jan 1, 1955

By L. E. Shiffman

This paper describes the operation of two kerosine flotation plants in Alabama for cleaning —10 mesh bituminous coal. One plant treats washer sludge, the other raw coal. Data on capacity efficiency and capital and operating costs is given. Methods for increasing cell capacity are discussed. IN cleaning coal it has long been recognized that methods which give excellent results for the coarser sizes may give poor or even no cleaning for the finer sizes. Effective cleaning of the fines, therefore, is usually a separate and distinct problem. For many years the problem of fines was considered of relatively minor importance. Now there is growing interest in methods of cleaning the fine sizes of coal because: 1. There are more fines. Increasing mechanization and the adoption of full seam mining methods have resulted in the production of a greater percentage of smaller particles than were produced by hand loading methods. 2. The fines have deteriorated in quality. The same causes that have led to increased quantity have also operated to decrease quality through greater contamination with slate, rock, and other diluents. 3. The fines have become more valuable. When coal was comparatively cheap, loss of the finer sizes was tolerated but, with the rapid increase in the cost of mining coal, it has become imperative that the maximum amount of clean coal be recovered from the mixture of coal and rock delivered to the tipple. 4. In many cases, the fines have become a stream pollution problem. Increasing governmental activity and legislation to prevent stream pollution often have made it necessary to retain the fine material which formerly was permitted to escape with the washer effluent into flowing streams. The Sloss-Sheffield Steel and Iron Co. operates four coal mines, all within a 20-mile radius of Birmingham, Ala., with a total annual production of 1,-250,000 tons of washed coal. Three of these mines are in the Mary Lee seam and one in the Jefferson seam. Although some steam and domestic coals are produced, the major portion of the coal is used to make coke for blast furnace operation. Fine coal is desirable for coking, and all the coal so used by Sloss is crushed to 1/4 in. Therefore, there is no problem of an outlet for even the finest sizes of coal. Since the coal is used for metallurgical purposes, low ash is of greater importance than would be the case if it were used for steam generation or domestic heating. Based on present blast furnace practice at Sloss, it is calculated that each percentage of ash in the coal carries a penalty of $0.22 per ton of coal. Thus there is a considerable margin for operating costs in a fine coal cleaning method that will result in materially lowering the ash content of the cleaned coal. Development of Fine Coal Cleaning Problem In 1942 Sloss reopened its Bessie mine and constructed at this location a new preparation plant to clean 11/4 in. x 0 coal from the Mary Lee seam.

Jan 1, 1951

By L. E. Shiffman

This paper describes the operation of two kerosine flotation plants in Alabama for cleaning —10 mesh bituminous coal. One plant treats washer sludge, the other raw coal. Data on capacity efficiency and capital and operating costs is given. Methods for increasing cell capacity are discussed. IN cleaning coal it has long been recognized that methods which give excellent results for the coarser sizes may give poor or even no cleaning for the finer sizes. Effective cleaning of the fines, therefore, is usually a separate and distinct problem. For many years the problem of fines was considered of relatively minor importance. Now there is growing interest in methods of cleaning the fine sizes of coal because: 1. There are more fines. Increasing mechanization and the adoption of full seam mining methods have resulted in the production of a greater percentage of smaller particles than were produced by hand loading methods. 2. The fines have deteriorated in quality. The same causes that have led to increased quantity have also operated to decrease quality through greater contamination with slate, rock, and other diluents. 3. The fines have become more valuable. When coal was comparatively cheap, loss of the finer sizes was tolerated but, with the rapid increase in the cost of mining coal, it has become imperative that the maximum amount of clean coal be recovered from the mixture of coal and rock delivered to the tipple. 4. In many cases, the fines have become a stream pollution problem. Increasing governmental activity and legislation to prevent stream pollution often have made it necessary to retain the fine material which formerly was permitted to escape with the washer effluent into flowing streams. The Sloss-Sheffield Steel and Iron Co. operates four coal mines, all within a 20-mile radius of Birmingham, Ala., with a total annual production of 1,-250,000 tons of washed coal. Three of these mines are in the Mary Lee seam and one in the Jefferson seam. Although some steam and domestic coals are produced, the major portion of the coal is used to make coke for blast furnace operation. Fine coal is desirable for coking, and all the coal so used by Sloss is crushed to 1/4 in. Therefore, there is no problem of an outlet for even the finest sizes of coal. Since the coal is used for metallurgical purposes, low ash is of greater importance than would be the case if it were used for steam generation or domestic heating. Based on present blast furnace practice at Sloss, it is calculated that each percentage of ash in the coal carries a penalty of $0.22 per ton of coal. Thus there is a considerable margin for operating costs in a fine coal cleaning method that will result in materially lowering the ash content of the cleaned coal. Development of Fine Coal Cleaning Problem In 1942 Sloss reopened its Bessie mine and constructed at this location a new preparation plant to clean 11/4 in. x 0 coal from the Mary Lee seam.

Jan 1, 1951

The Lake Superior Mining Institute, Ishpeming, Mich. A. J. Yungbluth, Secretary. An Annual Volume of Proceedings, carrying papers presented during the year, has been published since 1S83, with the exception of the years 1S97, 1899, 1907, 1916, 1918, 1919, 1920, 1921, 1924 and 1927. No meetings were held during those years and conse-

Jan 1, 1933

By K. E. J. Rapperport, C. S. Hartley

The only slip system observed in zirconium crystals deformed at 77", 575", and 1075OK was (1010) [1210] with a critical resolved shear stress in tension of 1.0 kg per sq mm at 77°K; 0.2 kg per sq mm at 575 °K; and 0.02 kg per sq mm at 1075 OK. The active twin planes were {1012}, (1121}, (11221, and (11233) with varying temperature dependence. A detailed analysis for the slip direction using Laue spot asterism is appended. NeARLY all metals of the hexagonal close-packed structure exhibit basal slip, i. e.,(0002)<1120>- type slip. This is true of magnesium,&apos; zinc,&apos; cadmium,3 beryllium,4 titanium,= yttrium,6 and rhenium.Many of these such as titanium 5&apos;8-&apos;0beryllium,4&apos;" magnesium, and zinc13&apos;14 display other slip modes even at room temperature, and nearly all have been reported to slip on other systems under particular loading or temperature conditions of testing. As is shown in this paper, basal slip was not found at any of four test temperatures from 77" to 1075°K in hexagonal close-packed zirconium under the simple loading conditions of tension and compression, even though in one case the resolved shear stress on the inactive (0002) <llgO> system was twenty-five times higher than the critical resolved shear stress on the active (1010) [1210] system. This result is consistent with prior studies on the active deformation processes in zirconium deformed at room temperature. &apos;&apos;-I7 SPECIMEN PREPARATION A) Material—The zirconium used in this work was of two types: 1) as-deposited reactor grade crystal-bar, and 2) arc-melted and forged reactor grade crystal-bar. Typical chemical and spectrographic analyses of these materials as received, and after hydrogen removal and crystal growth are given in Ref. 17. Crystals of type 1) above have the letter prefix (A) and those of type 2) have the prefix (B) throughout this paper. B) Crystal Growth— he zirconium was machined into rectangular parallelepipeds about 0.2-in. scl in cross section and 2 in. iong. These were hand polished through 4/0 abrasive paper, electropolished, given a hydrogen removal anneal, and subjected to long-time anneals at 840 °C in vacuo to produce usable crystals.&apos;7 A second technique used to obtain large crystals was to cycle the samples two or three times between 1200" and 840°C, allowing them to remain at the higher temperature for about 4 hr and at the lower temperature for 5 days.17 These techniques yielded some grains which occupied the entire cross section of the bar and were as long as 3/4 in. C) Orientation Determination—After the growth of large crystals by thermal cycling, the samples were repolished with extreme care through 4/0 abrasive paper and electropolished. Metallographic examination after polishing showed the surfaces to be free of visible deformation traces. Standard Laue back-reflection X-ray techniques were used to find the crystallographic orientations of selected large grains with respect to a specimen face and edge. Fig. 1 shows the stereographic projections of the stress axes for the crystals used. The sharpness of the spots on the Laue photographs indicated that the crystals were of good quality. EXPERIMENTAL METHODS Nine crystals were deformed in tension at 77"K, nine in tension and five in compression at 300°K in previous tests,17 fifteen in tension at 575"K, and eleven in tension at 1075°K. All specimens were stressed by load increments. After a predetermined load was applied, the specimen was removed from the loading appratus and metallographically examined for deformation traces. An attempt was made to initially stress each bar so that some crystals slipped a small amount and others not at all. This was done to bracket the critical resolved shear stress. One bar of special orientation (B-11) was repolished and annealed at 1075°K for 1 hr after lower temperature deformation, before final deformation at 1075°K. In the other bars the loading by increments, followed by metallographic examination, was continued until the surface distortion would interfere with analysis, or until fracture. One example of a crystal pulled to fracture is shown in Fig. 2. This photograph shows a crystal (B-14C) which was pulled at 1075°K and failed by slip on two (10i0) planes. The approximate orientation of this crystal is illustrated in the figure. Specimens were deformed at 77°K in liquid nitrogen on a tensile machine using an insulated bucket with an internal hook to accept a clamped specimen.

Jan 1, 1961

By Thomas M. Drown

At the meeting of the Istitote in New York, in February, 1880," I described a process of determining sulphur iu metallic allphides, with especial reference to the determination of pyrites in coal. The procem, as then described, is as follows: A solution of sodium hydrate, of 1.25 specific gravity, is saturated with bromine. If an excess of bromiue is used it must be neutralized by the addition of a little more sodium hydrate. The pulverized mineral or coal is moistened with 25 c.e. of this solution autl heated, then hydrochloric acid is added cautiously to just acid reaction. This operation is repeated with another 25 c.c. of the alkaline solution, and again rendered acid. The mixture should be kept hot. The contents of the beaker or dish are then

Jan 1, 1881

By R. B. Sosman, J. C. Hostetter

It is well known that ferric oxide, Fe2O3, is paramagnetic, while magnetite, Fe3o4, is classed among the highly ferromagnetic substances. But magnetic data on oxides intermediate in composition between Fe2o3 and Fe3O4 have been almost completely lacking. Fe2O3 and Fe3O4 form a solid-solution series, according to present evidence.&apos; In this series the properties change continuously from Fe2O3 toward Fe3O4, as the percentage of FeO increases from zero toward 31.03, which is the percentage in magnetite. It is possible that there is a break in the series near Fe3O4, but it has not yet been possible to establish the existence of such a break experimentally. The occurrence of solid solution in this series is shown by the dissociation pressure, or oxygen pressure in equilibrium with the oxides, which falls continuously over the range from Fe2O3 to Fe3O4. The oxygen-pressure curves at 1100" and 1200" are shown in Fig. 1. The existence of solid solution is also demonstrated by the continuous change in optical properties from Fe2O3 over to a composition containing about 18 per cent. FeO, at which point the opacity of the oxide becomes so great that it is impossible to obtain measurements at higher percentages of ferrous iron. Natural oxides of iron intermediate in composition between Fe2O3 and Fe3O4 are much more common than is generally supposed. If a mineral oxide is not strongly attracted by a small hand magnet and if it gives a red streak, it is usually labeled "hematite." If it is strongly attracted by the hand magnet it is usually labeled "magnetite" without further tests. As we shall show later, oxides containing from 1 up to 31 per cent. FeO can be thus erroneously lumped together as "magnetite." It is a fact, nevertheless, that the great bulk of natural oxides of iron lie fairly near either Fe2O3 or Fe3O4 in composition. The reason will be

Jan 1, 1918

In cooperation with the United States Bureau of Mines and the Idaho Bureau of Mines and Geology, the University of Idaho offers in the School of Mines a number of fellowships. These fellowships are open to college graduates who have had good training in mining, metallurgy, or chemistry, and who are qualified to undertake research work. The income of each fellowship is $720 a year for the 12 mo. beginning July 1, 1919. Fellows will register as students in the University of Idaho and become candidates for the degree of Master of Science in Mining or Metallurgy (unless this or an equivalent degree has been earned). Their class work-will he directed by the heads of the departments of instruction, but the greater portion of their time will be spent in research work under the direction of the Bureau of Mines staff resident at the University. The purpose f this work is to undertake the solution of definite problems confronting the mining and metallurgical industries of the State of Idaho. For 1919-20 the following subjects are being considered: 1. Flotation-with especial reference to differential separation of various minerals. 2. Availability of western wood oils for flotation purposes. 3. Treatment of the complex gold-silver ores of southern Idaho. 4. Ore-dressing problems. 5. Mining problems. Applications, with certified copy of collegiate record, statement of professional experience, and names and address of three references, should be addressed to The Dean. School of Mines. Moscow Idaho_

Jan 6, 1919

By Y. C. Liu

The orientation relationship between the dejormation and recrystallization textztres of binary Cu-P alloys of high phosphorus content was observed to he a ± 14-deg (110) rotation. According to the ori-ented-gvowth hypothesis, the same relationship should exist between a successfully flowing pain and the strained single-crystal matrix of alloys of corresponding composition. The orientations of thirty successfully growing grains were obtained in a Cu-1.0 at. pct P alloy. Both a conventional analysis and the more detailed analysis advanced in the present study demonstrate that the observed orientation relationship is not comparahle to that predicted by the oriented growth hypothesis. IT has been shown experimentally that the formation of recrystallization textures in metals may be explained on the basis of the oriented-growth hypothesis. This conclusion is based primarily on the results of cooperative experiments carried out by various investigators in aluminum. Beck and HU&apos; suggested that the orientation relationship between the recrystallization and deformation textures of aluminum is a 38-deg(111) rotation. A similar relationship, i.e., a 40-deg(111) rotation, was observed between the primary and secondary recrys-tallization textures.&apos; Since the secondary grains result from a process of selective growth, this naturally implies that the same mechanism is also responsible for the formation of the primary re-crystallization texture from the deformed matrix. Further evidence was provided by the experiments of Liebmann, Liicke, and Massing3 and Yoshida, Liebmann, and Lucke.4 They observed that grains which could successfully grow into strained aluminum single crystals invariably exhibited the same orientation relationships with their matrix. Thus, regardless of other opinions,5&apos;9 these results offered good evidence in favor of the oriented-growth hypothesis. In order to examine broader applications of this oriented-growth hypothesis, experiments should be carried out in metals other than aluminum. In a recent investigation on the recrystallization textures of binary copper alloys with phosphorus, arsenic, and antimony,7 it was found that the predominant recrystallization components were related to the deformation textures by a (110) rotation. The (110) rotational relationship is different from the (111) relationship generally proposed between the recrystallization and deformation components of other binary copper alloys. 1,8,9 Applying the observations made for aluminum, the oriented-growth hypothesis predicts that the orientation relationship of grains successfully growing into the strained single crystals of either one of these copper alloys should correspond to that observed in the textural study. Verification of this prediction would provide a critical test of general applicability of the oriented-growth hypothesis to the formation of recrystallization textures in fcc metals other than aluminum. The Cu-1.0 at. pct P alloy was selected in the

Jan 1, 1964

By J. H. Keeler

The tensile characteristics of Zr-Fe binary alloys containing up to 5 atomic pet Fe are reported for the temperature range —195o to 500°C. A linear relation between stress at constant strain and volume fraction ZrFe2 was found. The coincidence of data from unalloyed zirconium with zero volume fraction ZrFe2 indicated little or no solid solution in IL-zirconium, in agreement with Hayes, Roberson, and O&apos;Brien.&apos; The absolute increase in strength due to particle strengthening, although decreasing with increasing temperature, was a greater percentage at high temperature. ZIRCONIUM is of interest for use in nuclear reactors because of its low neutron absorption, good corrosion resistance, and high melting temperature. The alloying of zirconium with iron has been considered as a means of increasing the mechanical strength of zirconium without seriously increasing the neutron absorption " over that of unalloyed zirconium. The Zr-Fe system has a eutectic at 934°C and 23.7 atomic pet Fe and a eutectoid at 800°C and 4.0 atomic pet Fe. The zirconium-rich end of this system determined by Hayes, Roberson, and O&apos;Brien&apos; is shown in Fig. 1. The intermetallic phase coexisting with a and ß-zirconium has been reported as Zr2Fe3,1 with a,, - 7.04A, and as ZrFe2,2 face-centered-cubic, the phase being of the MgCu, type (C-15). It was more recently agreed to be ZrFe33 and face-centered-cubic. This intermetallic phase is essentially insoluble in a-zirconium, the hexagonal-close-packed modification; and the lack of solubility makes the system particularly interesting metallurgically. The system is strengthened almost exclusively by particles of in-termetallic phase, and there is very little solid solution strengthening to complicate the analysis. The Bureau of Mines, in its survey of zirconium-base alloys,&apos; reported the tensile properties of Zr-Fe alloys made from chloride process zirconium, induction melted in graphite crucibles, and swaged at 850°C in iron sheaths. Additional data on these ZrFe alloys were given by Hayes, Roberson, and O&apos;Brien.&apos; Chubb and Muehlenkamp% have recently reported the strength of Zr-Fe alloys containing up to about 1.25 atomic pet Fe. These alloys were made from crystal bar zirconium, hot worked at 820°C, annealed at 700°C, and tested both at room temperature and at 316°C. Experimental Procedure The materials used in this investigation were high purity zirconium made by the iodide process and electrolytic iron. The composition of the zirconium as obtained by spectrographic analysis and the nominal composition of the iron are given in Table I. Alloy ingots weighing 100 g were made by are-melting under argon in water-cooled copper crucibles in a multihearth furnace."

Jan 1, 1957

By M. S. Burton, B. W. Christ, G. V. Smith

Evidence of the effects which high-angle grain boundaries and veining subgrain boundaries have on the yield phenomenon of zone-refined iron is reported. Room-temperature tensile tests on 50-mil wive at several gram sizes produced upon recrystallization at diffevent temperatures below 910C (a-y phase-transfornzatzon temperature) show that upper and lower yield stress decrease with increasing grain size. The upper yield point effectively disappears at grain sizes of 81 and 102 u in samples of this diameter. However, samples of 129 p grain size. produced during recrys-tallization at 950°C, exhibit a pronounced upper yield point and an increased lower yield stress. Possible causes of the reversal in the grain-size dependence of yielding are discussed. Veining substructure, detected with picval-HC1 etchant, but not with 2 pct nital, is formed during the a-y transformation, and is believed to account for the observed effecls. The strengthening associated with high-angle boundaries in zone-refined tron is discussed in terms of: 1) the stress dependence of slzp multiplicity, and 2) the stress dependence of dislocation emission from grain boundaries. WIDE use of transmission electron microscopy and dislocation etch-pitting techniques has led to a growing awareness of the presence of dislocation substructures in annealed pure metals. Whereas much speculation&apos;-4 has developed about the influence which subgrain structures have on the mechanical behavior of metals, particularly the yield strength, only limited experimental evidence correlating subgrain structures with lower yield strength has been presented. 2,3,5-7 It is the purpose of this note to present experimental evidence of the effects which grain boundaries and subgrain boundaries have on both the upper and lower yield strength of zone-refined iron. Effects due to high-angle boundaries formed upon recrystallization below the a-y phase transformation are compared with effects due to veining subgrain boundaries formed upon "recrystallization" above the a-y phase-transformation temperature. These effects are further compared with the reported influence 2,3,5-7 which low-angle boundaries have on the lower yield strength of bcc transition metals. EXPERIMENTAL PROCEDURE The starting material for these experiments was a 1-in.-diam zone-refined ingot prepared at Battelle Memorial Institute. Initial purification of electrolytic iron by vacuum-induction melting was improved by a floating zone-melting treatment in ultrapure hydrogen.&apos; Chemical analysis of this zone-refined iron appears in Table I. Tensile samples of 50-mil wire were prepared by rolling and drawing portions of the ingot. An intermediate recrystallization anneal at 625°C after rolling to a reduction in area of 85 pct was carried out in an evacuated Vycor capsule (10-=5 mm Hg). Further reduction in area of 91 pct was followed by recrystallization in evacuated Vycor capsules at temperatures between 600" and 950°C, see Table 111. All samples

Jan 1, 1967

By Morris Muskat

Analytical calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/8 in., and to approximately one half for a perforation radius of 1/4 in., regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings. The increasingly important role being played by productivity factors of wells in determining well potentials and in the general evaluation of producing formations lends interest to the analysis of all the various factors that may infuence the productivity of a well. In recent papers1 the results have been given of theoretical studies made to determine the effect on the productivity factor of a well of the gas-oil ratio of the production and the connate water within the sand. These have served to show that both of these factors may, under suitable conditions, materially reduce the effective productivity factors below those that would be anticipated on the assumption that the wells produce homogeneous fluids. In this paper will be presented the results of the analysis of an entirely different factor influencing the productivity of a well. This refers to that resulting from the increased use of the method of completing wells by setting casing opposite all of the productive strata and then gun-perforating the particular zones of immediate interest. The practical success of this method of completion would appear to be an answer to the question as to whether it seriously reduces the well productivity or materially cuts down the ultimate oil recovery that may be derived from the producing section. Nevertheless, it is of interest to examine just how great the effect of the restricted flow channels, represented by the gun perforations, may be in increasing the over-all effective sand resistance. Of course, to the extent that the well potentials are severely restricted by proration regulations, minor reductions in well productivities are even less serious than if the wells were to be allowed to produce wide open. On the other hand, even under these circumstances there may be at least the academic interest in such calculations in being able to correct and evaluate the effect of the perforations in order to carry

Jan 1, 1943

By Morris Muskat

Analytical calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/8 in., and to approximately one half for a perforation radius of 1/4 in., regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings. The increasingly important role being played by productivity factors of wells in determining well potentials and in the general evaluation of producing formations lends interest to the analysis of all the various factors that may infuence the productivity of a well. In recent papers1 the results have been given of theoretical studies made to determine the effect on the productivity factor of a well of the gas-oil ratio of the production and the connate water within the sand. These have served to show that both of these factors may, under suitable conditions, materially reduce the effective productivity factors below those that would be anticipated on the assumption that the wells produce homogeneous fluids. In this paper will be presented the results of the analysis of an entirely different factor influencing the productivity of a well. This refers to that resulting from the increased use of the method of completing wells by setting casing opposite all of the productive strata and then gun-perforating the particular zones of immediate interest. The practical success of this method of completion would appear to be an answer to the question as to whether it seriously reduces the well productivity or materially cuts down the ultimate oil recovery that may be derived from the producing section. Nevertheless, it is of interest to examine just how great the effect of the restricted flow channels, represented by the gun perforations, may be in increasing the over-all effective sand resistance. Of course, to the extent that the well potentials are severely restricted by proration regulations, minor reductions in well productivities are even less serious than if the wells were to be allowed to produce wide open. On the other hand, even under these circumstances there may be at least the academic interest in such calculations in being able to correct and evaluate the effect of the perforations in order to carry

Jan 1, 1943

By N. Tiner

IN an article on magnesium and its alloys, Gann and Winston1 stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 695°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I): This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing o.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. EXPERIMENTAL METHOD The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945

By N. J. Grant, D. S. Bloom

An investigation of the Cr-Mo-Ni ternary system and attendant binaries has been completed. Some changes in the binary diagrams are shown to be necessary. The 1250°C section of the ternary and the liquidus surface have been delineated. A system of invariant reactions existing above 1250°C has been suggested. BECAUSE chromium, molybdenum, and nickel are important not only as bases for alloying systems but also as major alloying additions for other refractory metals, a study of the phase diagrams is of great interest and importance. In addition there are interesting features of theoretical value, a number of which are of prime consideration in this work. The major aim was to determine the ternary phase diagram of these metals at and above 1250°C, with sufficient attention given to lower temperatures to permit an understanding of the conditions existing at 1250°C and above. To understand ternary systems it is essential that accurate information concerning the binary systems be available, which in turn presupposes thorough knowledge of the constituent elements. On the basis of this investigation not only were significant inaccuracies indicated in the binary systems but much consideration had to be given to one of the elements, that is, chromium. The observation has been made that chromium undergoes a crystal transformation at a temperature near its melting point. Much of the experimental data leading to the detection of this transformation and the effects of this hypothesis on the form of the Cr-Ni phase diagram have already been reported&apos; . and will not be repeated here. The experimental methods employed in the investigation have also been covered.&apos;-" he purity of the molybdenum utilized in this work showed by qualitative spectrographic analysis that chromium, copper, iron, silicon, and tungsten were present in quantities of 0.1 to 0.001 wt pct. During the course of the investigation more than 100 melts were made, weighing from 150 to 200 grams each. Each of these melts was sectioned for chemical analysis and for specimens for examination in the as-cast and various heat-treated conditions by X-ray and metallographic means. All X-ray diffraction patterns reproduced here were made using chromium Ka radiation although iron and copper targets were used on occasions during the investigation. Experimental Results Mo-Ni-System: The most recent comprehensive investigation of the Mo-Ni system was made by Ellinger&apos; in 1942; the diagram as shown in the American Society for Metals Handbook is based on his work. The work done on the system in this investigation substantiated the general form of the diagram although some differences were observed. These are indicated by a comparison of Ellinger&apos;s diagram and Fig. 1, the latter showing the results of pertinent thermal analyses made in this research. It can be seen in Fig. 1 that the eutectic composition is

Jan 1, 1955

By Reuben B. Ellestad, Fremont F. Clarke

Lithium chemical plant extraction methods are discussed with reference to 1) base exchange with alkali sulphates; 2) processing based on roasting with lime; 3) miscellaneous methods; and 4) application of the Lithium Corp. process to extraction of lithium from run-of-mine, low grade spodumene ore, or concentrates. IN the early days of the lithium industry most of the production was from lepidolite, zinnwaldite, and amblygonite. Nearly all the early extraction processes described in the literature involve heating the finely ground mineral with sulphuric or hydrochloric acid. On subsequent water leaching most of the bases present in the mineral (especially aluminum) are dissolved as sulphates. As a result, the leach solution required extensive chemical purification before the lithium could be precipitated as carbonate. Following the remarkable growth of the lithium industry to its present size, zinnwaldite and amblygonite ores must be considered of minor importance only. Attention is now focused on spodumene, abundant enough in North America to be a major source of supply, and there are important supplies of lepidolite and petalite in Africa. The extraction processes described below all apply to spodumene, although several will also operate on other lithium minerals, such as petalite. Base Exchange with Alkali Sulphates: A distinct advance was made with the disclosures of Wadman and von Girsewalt. In these methods the finely ground silicate ore (spodumene or lepidolite) is intimately mixed with an excess of alkali sulphate (usually K2SO4) in at least a 1 to 1 proportion, and the mixture was heated to a relatively high temperature. Base exchange results, with the formation of lithium sulphate. A water leach dissolves the lithium sulphate, together with the excess potassium sulphate. Successful operation of this type of process requires very thorough grinding and mixing, as well as careful temperature control. The use of K2SO4 is objectionable from cost considerations since purification of lithium carbonate requires the use of potassium carbonate, if the K2SO4 is to be recovered and recycled. The lower solubility of K2SO4 as compared with Na2S04 is also objectionable, since it limits the concentration of the Li2SO4 solution to be precipitated by K2SO4. Early laboratory-scale investigation of this process by Lithium Corp. was not encouraging. Other related base exchange processes are those of Lindblad, Wallden, and Sivander3 and Sivander, Gard, Villestad, and Wallen4. The former covers the reaction of lithium silicate minerals with a sodium sulphate solution, at 100" to 300°C (under pressure), while the latter involves the extraction of silicate minerals with molten sodium sulphate. Both these processes would seem to be difficult and expensive to operate.

Jan 1, 1956

By Iichiro Omori

THE Mabuki process, a Japanese hearth process for the treatment of matte, uses the same princi-ple as the Bessemer steel process. The only difference between the two is that in the Mabuki proc-ess a hearth furnace, not a converter, is used. Though the hearth is not as good as the converter, the first cost is very low and the capacity is compara-tively small; so the process is most suitable for smelters FIG. 1.-PLAN AND SECTION OF HEARTH. having a small production. To construct the hearth, an excavation, 6 ft. in each dimension, is made in the ground and a drainage channel is dug at the bottom. Then all side walls are faced with stone or slag brick and the cavity is filled with fireclay or brasque, except the hearth at the top.

Jan 9, 1922

By John G. Simmons

A tutorial account of the tunnel effect between metal electrodes separated by a thin insulating film is presented. Energy diagrams of metal-insulator -metal sandwiches are briefly discussed, and the isothermal and thermal J-V characteristics for symmetric and asymmetric tunnel junctions are derived from a generalized expression. Experimental data from tunnel junctions are presented, and it is shown how, correlation between theory and experiment permits a determination of some of the oxide properties. Finally, the barrier heights in AT-Al2O3-A1 junctions determined by various inr3estigators are discussed. The object of this paper is to give a tutorial account of the electric-tunnel effect between metal electrodes separated by a thin insulating film and to illustrate its utility in the study of metal-oxide interfaces. This paper will emphasize the theoretical aspects of the electric-tunnel effect: however, a brief account of the more recent experimental work will be presented. A more comprehensive experimental study of the tunnel effect will be presented in the following paper by Drs. Pollack and Morris, see p. 497. We will open with a discussion of the energy diagrams for metal-insulator-metal junctions and what we mean by the electric-tunnel effect. Following this is an account of the theoretical studies of Sommerfeld and Bethe, and Holm, and the recently reported calculations on symmetric and asymmetric junctions using the generalized formula. The theoretical presentation is concluded with calculations on the temperature dependence of the tunnel J-V characteristic. In the experimental section, it is shown how barrier heights and thicknesses are determined by comparing the experimental data with the theory. Finally, the results of various investigators on the determination of the barrier heights in Al-Al2O,-A1 systems are discussed. I) POTENTIAL BARRIERS BETWEEN CLOSELY SPACED ELECTRODES Since it is necessary to supply energy to a metal in order to observe electron emission from its surface, it is evident that the potential energy of an electron within a metal is lower than that of an electron at rest outside the metal. It follows, then, that the electron must undergo a change in potential as it crosses the metal-vacuum interface. In the Sommerfeld1 free-electron theory of metals it is assumed that the free electrons, the electrons responsible for the electrical characteristics of metals, move in a constant potential environment in the metal, and are contained within the metal by a potential barrier at the metal-vacuum interface. It will be evident that the idea of a constant potential environment is a very idealized model, since the potential energy of an electron is influenced by all of the atoms and the other electrons within the metal; however, its use is justified by the many excellent results it gives.2 Fig. l (a) is the energy diagram of the model envisaged by Sommerfeld; the metal is represented by a potential-energy well of depth V,; the vacuum level represents the energy of an electron at rest outside the metal. At 0°K the electrons, which exist in pairs in discrete energy levels, fill up the well to an energy ?, the Fermi level. The distance, Vo - ?, from the Fermi level to the vacuum level is known as the work function of the metal, and represents the minimum energy required to free electrons from the interior of the metal at 0°K.

Jan 1, 1965