Search Documents

By B. B. Betty

H. L. Burghoff.*—Have the authors any information on the effect of grain size in these materials? There is a material difference in the grain sizes shown for the Monel and the Inconel. Is a wide range of grain size normally found for each material, and, if so, what is its effect upon creep strength? 11. L. Eiselstein.—The grain size for Monel shown in the micrograph is the usual size found in that product. The grain size of Inconel is about the same as that, too. However, we have run tests on Inconel at higher temperatures than those reported in this paper, and have found that the coarser grain size has a better creep resistance; and that the grain size that gives the best creep resistance at 1600°F. is about 0.005 in. in diameter. We have no test on Monel with varying grain size. J. J. KANTER.†-It has been known for a long time that Monel metal exhibits ductility anomalies at elevated temperatures. Even in short-time test, it can be demonstrated in the range of 900°F. that there is a distinct falling off of the ability of Mone1 metal to elongate, and in rupture tests this shortcoming is still further accentuated. Knowledge of this rupture anomaly of Monel metal may be one of the reasons for which designer's approach certain high-temperature applications with reservations. The authors of this paper have merely demonstrated that for 900°F. the alloy has an ability to elongate 1.7 per cent over a period of some 2700 hr. Before any conviction can be expected from designers that Monel metal is applicable to stress design in such range of temperature, I think it is desirable to demonstrate the capacity for the material to elongate over a longer period of time than has been done in this presentation.

Jan 1, 1945

By J. Jones-Parra, J. C. Calhoun

INTRODUCTION The purpose of this paper is to present the results obtained by solving the fractional flow' and frontal advance' equations to obtain oil recovery at water breakthrough as a function of the length of the system being flooded, the linear velocity of injection and the displacing phase viscosity. The method of solution makes use of the stabilized zone concept first presented by Terwilliger, et al3 when calculating saturation distributions in a gravity drainage system. In order to check the calculated results, the equations and method of solution were applied to the system on which Rapoport and Leas' reported experimental data. METHOD OF SOLUTION The solution of the fractional flow equation and the frontal advance equation is obtained by assuming that a water front forms to sweep the oil out ahead of it. There is ample evidence that under the proper conditions a water 'front does form. If this water front is not to dissipate, the water saturations which comprise it must have equal linear velocities. These water saturations are said to comprise the stabilized zone. Equation (2) indicates that for all these saturations and hence fw must plot as a straight line against saturation for those water saturations comprising the stabilized zone. The water saturations lying between the highest in the stabilized zone and the highest that can be achieved in the porous medium comprise the variable zone. Regardless of the numerical value of the length of the system, the variable zone must eventually span all of it, so that for long enough systems in Equation (1) will be small enough to be neglected. Hence, for the saturations in the variable zone Equation (1) can be simplified to In order to determine the composite fw function applicable to the entire range of saturations in the porous medium, it is necessary to find the water saturation which separates the stabilized zone from the variable zone. This dividing saturation must be on the curve defined by Equation (4), and a tangent curve at that point must pass through the initial water saturation to satisfy Equation (3). Hence, the valid fw curve is given by a straight line starting at the initial water saturation, tangent to the curve of Equation (4): and along the curve of Equation (4) from the point of tangency on. The point of tangency determines the water saturation dividing the zones. The length and shape of the stabilized zone can be found by solving Equation (1) for Integrating this expression numerically between any two saturations in the stabilized zone gives the distance separating these two saturations. By repeated integration, the saturation distribution of the stabilized zone can be determined. The total length of the stabilized zone is given by The integral appearing in Equation (5) is a function of the viscosity ratio, the capillary properties of the rockfluid system, the relative permeabilities, and the initial water saturation. Considering these variables fixed and designating the value of the integral by writing caw for and v/60 for q/A; Equation (5) becomes The saturation distribution of the stabilized zone can be integrated over its length and divided by the length to obtain the average water saturation The volume of water in the stabilized zone is then given by The average water saturation in the variable zone can be found by extending the straight line segment of (the segment joining Sw and Sw) until it intersects fw = 1.00. The saturation at the intersection is. This method of finding is nothing more than the graphical solution of the equation The volume of water in the variable zone at breakthrough is then given by Assuming no initial water saturation, the recovery at breakthrough expressed as percent pore volume is given by

Jan 1, 1953

By B. T. Brady

Rock mechanics, like all engineering disciplines, must have a theoretical foundation. The subject of this chapter is the formulation of analytical methods that may aid in the rational design and determination of the stability of engineering structures in competent brittle rock materials. By an engineering structure in rock, we mean any (1) excavated sub- surface opening, (2) open surface structure, or (3) system of openings in rock that is virtually self-supporting-that is, not requiring artificial systems to carry structural stresses. One factor necessary for designing or evaluating a structure's stability is knowledge of the material's mechanical properties, such as stress-strain behavior and fracturing characteristics. The composition of most structural materials such as metals and concrete is uniform and reproducible to the degree that their mechanical properties in service are nearly the same as those measured in the laboratory. Consequently, a rational design can be made on the basis of published mechanical property values. The same equivalence does not exist for rock materials for two reasons: (1) the composition of even the most common rock types is highly variable, and (2) the problem of the size effect is present. Mechanical property tests not conducted at a scale that includes these effects in normal proportion will not be representive of the in-situ rock mass. Of course, the alternative is to perform the test in-situ. Comparatively few mechanical property tests have been performed in-situ because of the physical limitations of test equipment and the prohibitive cost. The current procedure is to design a structure based on small-scale laboratory measurements, with a safety factor usually determined by the experience of the design engineer. While this procedure is somewhat unsatisfactory, laboratory measurements can and do provide a useful basis for the initial design.

Jan 1, 1970

By J. J. Bodmer

THE four different modes, more or less practiced for subdividing slag (that is, producing slag sand), are the following : 1. Crushing the slag from the lump in Blake's crusher, by edge runners or other suitable means. 2. Blowing water, steam, cold or hot air, into the stream of viscous slag whilst it runs from the furnace. So treated, the slag takes

Jan 1, 1874

By A. F. Nylander, J. H. Jensen

Magnesium, in its combined forms, is the sixth most abundant element and the third most abundant metal in the earth's crust, but it is so reactive that it is never found in nature in the elemental state. As part of the rock-forming minerals like magnesite, dolomite, olivine, and serpentine, it is combined in virtually insoluble forms. As part of soluble minerals like kainite (KC1 MgS04 - 3H20), leonite (K2S0, MgSO, 4H20), langbeinite (K,SO, 2MgS04), and carnallite (KC1 . MgCl? 6H20), it is found in evaporite deposits, generally of marine origin, deep within the earth's crust. Since these minerals are soluble, they are found only in deposits protected from the percolation and leaching action of ground waters by an insoluble and impermeable mantle. Usually this mantle is from several hundred to many thousands of feet thick. Finally, as a solute in marine-like brines, magnesium is common in surface and subterranean waters throughout the world. The oceans, which contain 0.13% Mg, illustrate the inexhaustible nature of the reserve. The recovery of magnesium from the rock-forming minerals, usually by thermal decomposition, and from dilute brines such as sea water by precipitation with lime, are frequent industrial practices. But the recovery of magnesium as magnesium chloride from evaporites or natural brines of concentration greater than sea water has been of little industrial significance for economic and technological reasons. The present US capacity is preponderantly based on the sea-water magnesia process with thermal reduction capacity in second place. No present magnesium capacity is dependent on recovery from the stronger natural brines. But projected capacity, although still weighted in favor of the sea-water magnesia process, is partly based on the recovery of magnesium chloride as a byproduct of potash operations.

Jan 11, 1964

By A. Steiner, K. L. Komarek

Activities of aluminum in solid Ni-A1 alloys have been determined between 20 and 60 at. pet Al and 1200" and 1400°K by an isopiestic method in which nickel specimens, heated in a temperature gradient, are equilibrated with aluminum vabor in a closed all-alumina system. The activity of aluminum shows a strong negative deviation from Raoult's law at low concentrations but increases by three orders of magnitude within the ß(NiAl) phase. The partial molar enthalpy and entropy of mixing are negative. Using Wagner and Schottky's theory of ordered compounds, a degree of disorder of 4 x 10 -4 for NiAl and 1.25 X 10-2 for FeAl has been calculated THE Ni-A1 system has been studied by a great number of investigators, and the results, as far as the phase diagram is concerned, have been compiled by Hansen.1 The phase boundaries from 0 to 50 at. pet Ni are well-established. At higher nickel contents the boundaries are still in dispute and an additional phase, A12Ni3, has been reported.' The phase diagram is dominated by a very stable high-melting compound, NiA1, with a relatively wide range of homogeneity. Heats of formation of solid alloys have been determined calorimetrically by Oelsen and Middel3 from 20 to 95 at. pet Ni and by Kubaschewski4 from 25 to 80 at. pet Ni. According to the most recent compilation5 no other thermodynamic investigations have been reported for the Ni-A1 system. Due to the corrosive nature and the low vapor pressure of aluminum, a method has been employed for determining activities of aluminum which was previously developed for the Fe-A1 system.= Nickel specimens, heated in a closed evacuated alumina system in a temperature gradient, were equilibrated with aluminum vapor from a source within the system kept at constant temperature. After complete equilibration the specimens were analyzed and activities calculated from the known vapor pressure of aluminum. APPARATUS AND EXPERIMENTAL PROCEDURE Materials. The nickel specimens were made from wafers of electrolytic nickel (International Nickel Corp.) of 99.99 pet purity which were rolled to a 0.001-in.-thick foil by Driver-Harris Co. and to a 0.005-in.-thick sheet in our laboratory. The aluminum (Aluminum Corp. of America) had a purity of 99.99+ pct. The alumina tubes and crucibles were made of impervious recrystallized alumina with an alumina content of 99.7 pet (Triangle RR, Mor-ganite Inc.). Experimental Procedure. Annular specimens were punched from the sheet, the punching burrs removed, and the specimens degreased in carbon tetrachloride and acetone and weighed on a micro-balance to within an accuracy of ±0.01 mg. The specimens were positioned with alumina spacers along an alumina tube, and the positions measured. Aluminum metal was machined into cylindrical shape, and placed into an alumina crucible. The tube with the specimens was then inserted into a hole drilled into the aluminum metal. An alumina tube with its closed end at the top was slipped over the specimens so that its lower end fitted snugly into the alumina crucible. The assembled reaction tube was inserted into a mullite tube with a water-cooled brass head which had an opening for a quartz thermocouple protection tube and a metal-to-glass connection to a conventional vacuum system. A Pt-Pt 10 pet Rh thermocouple could be raised and lowered in the quartz tube which was placed along the outside of the alumina reaction tube. The mullite tube was heated by two separately controlled resistance-tube furnaces so that in the experimental temperature range an over-all temperature gradient of approximately 150o to 250°C could be imposed on the reaction tube. The position of the mullite tube was adjusted so that the surface of the aluminum metal was always at the temperature minimum. The reaction tube was thoroughly evacuated before and during slowly heating the assembly up to the melting point of aluminum. A pressure of less than 2 µ (Hg) was maintained during an experiment. Once the aluminum had melted, it isolated the contents of the alumina tube from the surroundings. Several times during an experiment the temperature gradient was carefully measured. An experiment lasted from 3 to 6 weeks and it was terminated by air cooling the evacuated mullite tube. For further details of the experimental procedure the paper on the Fe-A1 system6 should be consulted.

Jan 1, 1964

By H. C. Rolseth, J. J. Calaman

6.4-1. Principles of Operation. The jet-piercing process is a patented thermal process which depends upon a characteristic of the rock which is termed spallability. In its simplest terms, spalling is considered as decrepitation resulting from differential expansion of rock crystals due to thermally induced stresses. The number of individual properties influencing the spalling characteristics of rock are so numerous and their interaction so complex that the only truly reliable way to ascertain the spallability of rocks under thermal shock conditions is to expose them to these conditions. However, laboratory and field work have determined the principal thermal, physical, and mechanical properties of rock which affect spallability (10, 18). The approximate relationship between spallability and these characteristics is as follows: [ ] where To is the critical temperature at which, it is believed, a rock becomes elastic or sufficiently plastic to prevent further spalling action. Thermal diffusivity takes into account the amount of heat used in saturating the medium itself during the migration of a heat front. The rate and degree of dimensional changes which influence the spalling tendency of the rock will depend upon the characteristic of the heat gradient in the rock. The greater the spalling tendency, the higher the piercing rate. Those properties most favorable to a high degree of spallability are: 1. Large linear thermal expansion at temperatures below 700°C. 2. High thermal diffusivity at temperatures below 400°C. 3. Equigranular interlocking structure with little or no fine-grained clay or mica alteration products. 4. No significant amounts of soft, low-melting, or elastic mineral or materials which yield after thermal decomposition.

Jan 1, 1968

By John F. Elliott, John R. Rawling

The rate of reduction of silica to silicon by carbon at 1550° to 1700°C in iron blast-furnace type slag-metal systems has been investigated. In the tower portion of the temperature range oxygen transport in the metal boundary layer at the slag-tal interface is probably rate limiting. A second step, which apparently involves a chemical process in the slag at the slag-metal interface, appears to be rate limiting when the oxygen-transport limitation is avoided. Above 1650°C rate control of the reduction by carbon probably is mixed between the two steps. INVESTIGATIONS1.2 into the equilibrium distribution of silicon between graphite-saturated slags and metals typical of iron blast-furnace practice show that, under the experimental conditions specified, the reduction of silica to silicon is relatively slow compared with the rates of other slag-metal reactions under similar conditions. For this reason, the reduction of silica in blast-furnace slag-metal systems was considered to be an interesting subject for further study. Investigations of the kinetics of the reaction3-5 suggest that several possible steps may be rate controlling, and that the rate-controlling step depends not only on the physical state of the systems but also on the configuration of the apparatus. The main objects of the investigation reported here were to sug- gest plausible reaction paths for the reduction of silica under the experimental conditions chosen and to determine the step or steps which control the rate of reduction of silica. EXPERIMENTAL Two types of experiments involving the reduction of silica from the slag were carried out. In the first, the only reducing agent present was carbon (graphite), for which the over-all reaction is (SiO2) +2C(gr) —Si + 2Co(g) [l] The second type was a graphite-saturated ferro-silicon-iron concentration cell. In it silica in the slag could be reduced either by carbon according to Eq. [I], or by a reaction of electrochemical nature in which silicon was oxidized at the ferrosilicon-slag interface and silica was reduced at the slag-iron interface without the formation of CO. The two types of experiment are described below. Reduction of Silica with Carbon as the Only Available Reducing Agent. The reduction of silica was accomplished by allowing a liquid lime-alumina-silica slag and graphite-saturated iron to react in an induction-heated graphite crucible. The crucible was 2.25 in. diameter and 5 in. deep; it was fitted with a graphite stirrer which penetrated through the slag and into the metal, Fig. 1. The slag and metal charges weighed 350 g each. Pure carbon monoxide at a pressure of 1 atm was maintained above the melt by passing the purified gas through the crucible at a rate of 0.5 liter per min. The gas did not stir either the slag or metal. Temperature measurements were made by sighting an optical pyrometer down the hollow stirrer rod into a 1/4-in. hole drilled in the stirrer blade. The crucible temperature was maintained within *15"C of the required value by manual control of the power supply to the

Jan 1, 1965

By Aloys IL. Wollrab

The conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and . shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. Conventional Drill Bit in Use That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8-in. steel show that when bit sizes are reduced from I½ in., I3/8 in., and I3/16 in-; to I3/8 in., I1/4 in.., and I1/8 in., respectively, the volume of the hole is I 5 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I,826 in., a difference of o.25I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr charac1erist.i~~) by some mines4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as call be forged economically. Shop practices and costs have been discussed in earlier paper.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert. Requiremnts for Detachable. Bit for Hollinger Under these it it was appar- ent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1943

By Aloys IL. Wollrab

The conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and . shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. Conventional Drill Bit in Use That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8-in. steel show that when bit sizes are reduced from I½ in., I3/8 in., and I3/16 in-; to I3/8 in., I1/4 in.., and I1/8 in., respectively, the volume of the hole is I 5 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I,826 in., a difference of o.25I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr charac1erist.i~~) by some mines4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as call be forged economically. Shop practices and costs have been discussed in earlier paper.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert. Requiremnts for Detachable. Bit for Hollinger Under these it it was appar- ent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1943

By C. C. Clark, J. S. Iwanski

The purpose of this investigation was to study mi-crostructural changes that take place in a commercial nickel-chromium-iron alloy, such as Incoloy "901," over long periods of time at temperatures up to 13 50°F and to correlate such changes with creep-rupture properties. of the alloy. In the course of the investigation, some microstructural changes were observed which correspond to microstructural alterations found in previous studies of Inconel "X." Microstructural phases have been identified in both alloys with the aid of electron and X-ray diffraction and an electron probe microanalyzer. The materials used in this investigation were from commercial heats of the following chemical composition: Pct Cr Pct Ni Pct Mo Pct Fe Pct Cb Incoloy "901" 12.51 43.67 5.72 Bal. -Inconel "X" 14.61 73.44 - 6.61 1.02 Pct A1 Pct Ti Pct Mn Pct Si Pct C Incoloy "901" 0.10 2.46 0.46 0.24 0.05 Inconel "X" 0.70 2.43 0.51 0.36 0.04 Long-term creep-rupture tests were conducted on Incoloy "901" at temperatures of 1000°, 1200°1 and 1350°F. A summary of these results is shown in Table I along with the results of a long-term creep-rupture test conducted on Inconel "X" at 1500°F. The heat treatments given the specimens are also shown in Table I. When the creep-rupture results on Incoloy "901" are compared with shorter-tertn data, there is no evidence of any undue deterioration of the creep-rupture strength with time, nor is the elongation decreased more than would be expected from the influence of time alone. INCOLOY "901" PHASE IDENTIFICATION Microscopic examination of the Incoloy "901" specimens reveals a dark etching grain boundary constituent in the specimen which was under test for about 11,500 hr at 1000°F. This grain boundary constituent was seen to increase in size as the test temperature was increased to 1200" and 1350°F, Figs. 1, 2, and 3. Simultaneously, an acicular structure of definite crystallographic orientation appears within the grains of the 1350°F specimen, Fig. 3. Under examination with the electron microscope, a fine precipitate is observed in the 1200 °F specimen. Fig. 4. It becomes considerably larger in the 2850-hr 1350°F specimen, Fig. 5. In a few areas the precipitated particles have been replaced by, or transformed to, small needles or platelets. After 7380 hr at 1350°F, Figs. 3 and 6, the needles are much larger and have replaced nearly all of the fine precipitate. X-ray diffraction studies detected the presence of hexagonal Laves phase and hexagonal n phase (Ni,Ti) in the 1350°F specimens, Table 11. Only the Laves phase was detected by X-ray diffraction in the 1200°F specimen and none was detected in the 1000°F specimen. In this latter specimen, however, the small quantity of precipitate in the grain boundaries (presumed to be Laves phase) precludes its detection by X-ray diffraction. Composition of the hexagonal Laves phase is not yet known, although its diffraction

Jan 1, 1960

By R. A. Stauffer

The chief ore of lithium is spodumene, a lithium-aluminum silicate containing up to 3 pct lithium. The preparation of lithium salts from spodumene is costly because of the low concentration of the metal and the difficulty of separating it from the other alkali metals present. Dr. Kroll's and Dr. Schlecten's recent paper1 has reviewed various methods proposed for preparation of lithium. It will be seen from this paper that the methods proposed to date have required one or another of the lithium salts as a raw material. The high cost of these salts has been the chief item of expense in the lithium metal produced. This situation has made it interesting to investigate the possibility of producing the metal directly from spodumene. When spodumene is calcined at 1000ºC in the presence of lime, lithium oxide is replaced in the ore as is evidenced by the fact that it may be leached from the reaction mixture with water.2 Free energy calculations suggested that lithium oxide might be reduced with aluminum or silicon and the lithium produced distilled from the reaction mixture by heating-to about 1000ºC in a vacuum. These facts taken together suggested that it might be possible to prepare lithium metal directly from spodumene by heating a mixture of the ore, lime, and a suitable reducing agent in vacuum and distilling off the lithium metal as formed. The Replacement of Li2O in Spodumene A series of experiments were undertaken to determine the ratio of lime to spodumene necessary to free substantially all the lithium oxide Present in the Ore. The spodumene used in these experiments was supplied by Foote Mineral Co. in the form of powder of about 200 mesh' Analysis of the spodumene was as follows: PCT SiO2......................... 62.7 Al2O3........................ 29.9 Li2o......................... 4.9 Na2O........................ 0.89 CaO......................... 0.75 MgO........................ 0.49 K2O......................... 0.44 Lime (cp —200 mesh) was added in various ratios to spodumene and thoroughly mixed in a ball mill. Two hundred gram samples of spodumene-lime mixtures were charged loosely in fireclay crucibles and held at 1000ºC in a gas-fired furnace for 5 hrs. The product in each case was ground to pass 140 mesh and then placed in a thimble in a soxhlet extractor. Extraction with water was carried on for 6 hrs. After this period the extract was reduced in volume by evaporation in order to precipitate dissolved lime and was then filtered and titrated with 1/4 normal hydrochloric acid. After correcting for residual calcium oxide in solution, the alkali present was calculated as lithium oxide. The results of these experiments are shown in Table I and Fig I. At lime-spodumene ratios less than 1.5, the products were invariably fused. At the ratio of 1.5 and above, the product was loosely sintered with little evidence of fusion. When the ratio of lime to spodumene was three, replacement of alkali oxides in the

Jan 1, 1949

By Irving Cadoff, Richard Nolder

An analysis oj a series of samples of single -crystal silicon grown on sapphire shows that ,four distinct orientation relations exist. There are at least thirteen crystallographic planes which serve as substrates ,for epitaxial growth The model which assumes that silicon substitutes for aluminium and bonds with the oxygen atoms of the sapphire to form the first later for subsequent growth can account for the epitaxial geometry in all four cases. Multiplici-ties 01 specific orientations are found which are explained by the symmetry of both the sapphire and silicon crystal structures. It was reported in the previous paper' that single-crystal silicon films can be deposited on single-crystal a A1,03 (sapphire) with a wide variety of orientations. The silicon films, however, were found to deposit in only four different orientation relationships with respect to the sapphire substrate. The X-ray data have been analyzed to determine the plane and direction of atomic fit and an atomic model to account for the epitaxial relationships at the silicon-sapphire interface has been developed. These results are described in the present paper. EXPERIMENTAL The Laue X-ray data described in the previous paper were reduced to stereographic projections in a standard manner. These data were supplemented with X-ray reflection data obtained with -& E and A Full-Circle Goniometer (Electronics and Alloys, Inc.) mounted on a Phillips diffractometer unit. The silicon films were thin enough to result in characteristic reflections from the substrate as well as the silicon. The superimposed stereographic projections were analyzed to determine the orientation relationships. Ambiguities were resolved by referring to constructed models of various lattice planes for both silicon and sapphire. These lattice models were also used to develop the model for atom fit at the interface. DATA AND ANALYSIS 1) Crystal Structures. The crystallography of silico-n, which is of the diamond cubic class with a. = 5.4~, is straightforward. The sapphire structure is more complex and generally difficult to represent in pictorial form. It is of the rhombohedra1 class but usually referred to hexagonal axes. The transformation of indices between these two systems can lead to ambiguities which will have bearing on the analysis presented herein. Therefore, the basis used in this paper is described in the appendix. Referred to the hexagonal system, the parameters of sapphire are co = 12.95.&, a, = 4.75~, c/a = 2.73. All parameters are for room temperature. Figs. 1 and 2 illustrate schematically the hexagonal unit cell model of sapphire used for this analysis. The oxygen atoms are assumed to occupy positions in an idealized hexagonal array on basal planes. Their actual positions are in a slightly distorted hexagonal array. The aluminum-atom positions are scaled to their actual positions in the lattice with respect to the basal layers of oxygen atoms. It was found that an idealized model where the aluminum atoms are assumed to lie exactly at the octahedral interstices of the oxygen lattice, similar to that used by ~ronberg,' was not adequate for this study.

Jan 1, 1965

By T. Toda, R. Maddin

A study has been made of the microstructure and mechanical properties of splat-cooled aluminum-base gold alloys with gold concentration from 0.25 to 5.0 wt pct. These alloys have been quenched from the liquid state by a torsion-catapult technique, which has made it possible to pepare specimens suitable for mechanical property measwements. From the electron micrographs it has been shown that the solid solubility of gold in aluminum can be extended to 2.5 wt pct (0.35 at. pct) by splat-cooling, while the maximum equilibrium solubility is known to be less than 0.3 wt pct (0.04 at. pct). The very fine grain size (several tenths of a micron), the extended solid solubility, and the fine dispersion of a second phase (AuAl2) contribute concurrently to a substantial strengthening effect. In Al-5 wt pct Au splat-cooled specimens of less than 50 thickness, the yield strength is 17 kg per sq mm or 6 times as large as the strength of bulk specimens. For the Al-1.0 to 2.5 wt pct Au solid solution obtained by splat-cooling, the yield strength reaches 7.5 kg per sq mm after an aging treatment (for 10 hr at 200°C), while it is 3.7 kg per sq mm for the corresponding bulk specimens. A great deal of research has been done in recent years on the structure and the properties of metals and alloys rapidly quenched from the liquid state.' The term "splat-cool" has been used with the meaning of a rapid quenching from the liquid state., The splat-cooling techniques have produced large numbers of new structures, which are expressed in terms of metastable phases,3 concentrated solid solutions,4 amorphous phases,5'6 new phases,7 and so forth. Nearly all previous studies have concentrated on the physical properties; i.e., crystallography, structure, electrical resistivity, magnetism, and so forth, of the splat-cooled metals and alloys. The mechanical strength of splat-cooled metals and alloys has hardly been investigated except for some recent work by MOSS' on A1-V alloys. The principle common to all experimental techniques developed to obtain very rapid quenching rates is based on the heat transfer by conduction. Liquid must be in good thermal contact with a substrate of high heat conductivity. Both of the published devices known as the "gun" and the "piston and anvil" techniques suffer from certain shortcomings. For example, the specimen obtained by the gun technique is very small and flaky, and hence inadequate for mechanical properties measurements. On the other hand if the material is forced to yield a continuous speci- men by the piston and anvil technique, it is probable that some plastic deformation occurs during the quench. A novel method for rapid quenching of a liquid metal or alloy, the "torsion-catapult", has been devised by Roberge and Herman9 at the University of Pennsylvania. In the apparatus the melt is thrown out of a curved furnace by a catapult and impinges on a copper substrate. The apparatus has the advantage of producing a continuous foil which is relatively large in size and of a quality suitable for the measurements of mechanical properties. The quenching rate is estimated to be of the order of l05 to l06 ºC per sec, (comparable to rates achieved by the piston and anvil technique). In selecting an alloy to be studied we were made aware of the fact that gold was believed to be "insoluble" in in and consequently age hardening in the A1-Au system appeared to be interesting. Quite recently Heirnendahl13-15 revealed that the solid solubility, as determined by transmission electron microscopy, was 0.3 wt pct Au at 640°C and 0.25 wt pct Au at 600°C, decreasing with decreasing temperature. In an A1-0.2 pct Au alloy after quenching from a solution treating temperature of 600°C the yield stress was 2 kg per sq mm, and it increased up to 6 kg per sq mm after aging for 1 to 10 hr at 200°C. The precipitation occurred in the form of platelike particles mainly on (100) matrix planes. The intermediate phase n', the equilibrium phase n (AuAl2), and lattice relationships between both precipitates and the matrix were also investigated by electron microscopy. One of the purposes of the present research is to determine whether or not the solid solubility in this system, in which gold has a very small solubility in

Jan 1, 1970

By P. Pietrokowsky, T. E. Tietz, J. E. Dorn

The amount of solid solution hardening in aluminum alloys was found to be dictated by two factors: the lattice strain, and the change in the mean number of free electrons per atom of the solid solution. To obtain this correlation it was necessary to assume that aluminum contributes two electrons per atom to the metallic bond. WHEN the modern scientific method of analysis was first being formulated, Francis Bacon recorded in his "Essays" (circa 1600) that "an alloy . . . will make the purer but softer metal capable of longer life." During the intervening centuries voluminous data have been reported which demonstrate that the additions of alloying elements do in fact increase the hardness and strength of the pure metals. Nevertheless, the significant details of this problem on the unique effect of each element toward enhancing the mechanical properties of alloys only recently have been subjected to systematic scientific scrutiny. The major objective of this investigation is to determine how minor additions of alloying elements affect the plastic properties of polycrystalline aluminum alloys. By means of such studies it is hoped to provide not only data on the solution strengthening of aluminum alloys, but also a body of facts which will supplement the knowledge already available on the factors responsible for solution hardening in general. A review1"10 and analysis1' of the existing data on the effect of solute elements on the plastic properties of solid solutions reveal that our current knowledge on solid solution hardening is somewhat meager, inconsistent, and inconclusive. Many of the inconsistencies are undoubtedly attributable to the influence of unsuspected factors, such as purity; or uncontrolled factors, such as grain size, on the plastic properties of alloys. Nevertheless the following conclusions might be tentatively accepted: 1. Addition of solute elements invariably increases the yield strength, tensile strength, and hardness of the host element. 2. The rate of strain hardening, in general, increases with the concentration of the alloying element. 3. The strengthening effect in ternary alloys is the sum of the individual strengthening effects of the two solute elements as measured in their binary alloys. 4. The lattice strain is one factor that affects the strengthening of the alloy but it is not the only factor. 5. A second factor might be the difference in valence between the solute and solvent metals. All of the available evidence is in complete agreement with the first conclusion; the remaining conclusions, however, are not in agreement with all of the published data, but, in each case, the major weight of the existing evidence favors these deductions. Additional investigations will be required before most of these tentative conclusions can be accepted without reservation. In the following report an extensive investigation of the plastic properties of binary aluminum alloys is described. This work was undertaken in an attempt to shed more light on the general problem of solid solution hardening. Materials for Test: Aluminum was selected as the solvent metal for the present investigation on the effect of solute elements on the plastic properties of alloys. This choice was made for several reasons: (1) There appears to be little fundamental data in the published literature on the effect of solute elements on the properties of high-purity aluminum alloys. In view of the ever increasing economic importance of aluminum, such data would be of basic interest to the metallurgists concerned with the development of new aluminum alloys. (2) Aluminum is thought to be only partially ionized in the metallic state1' and consequently it might provide more complex relationships of the mechanical properties with the concentrations of the solute elements than more simple fully ionized solvents would reveal. (3) The data on aluminum alloys will provide a broader basis for correlations between the mechanical properties of metals in general and the concentration and atomic properties of the solute elements than is now available. Some complications, however, attend the selection of aluminum: The solubility of the various elements in the alpha aluminum phase are quite restricted, and not always well known. Consequently, only dilute solid solutions are available for study. This, however, may be somewhat advantageous because the dilute solution laws presumably are simpler than those applying to concentrated solutions. In addition, strain-hardened pure aluminum is known to recover at atmospheric temperatures. Very likely its alloys exhibit slower recovery rates. Thus, the secondary factor of effect of alloying elements on recovery might complicate the data. Such compli-

Jan 1, 1951

By L. Ekstrom, J. P. Dismukes

The homogeneity and microstrcture of zone-leveled Ge-Si alloys haw been investigated by sellera1 physical techniques and by metallography as a function of growth rate in the range 3 x 10 1x10 cm-sec', and as a system of alloy composition throughout the system. The temperature gradient at the solid-liquid interface was about 50 deg-cm-' Cellular or dendritic structures char-acteristic of constitutional supercooling were ob-served except at very slow growth rates, which ranged from about 2 x 10 cm -sec for Ge 1 sio alloy to about 2 X 10'5 cm-sec'1 for Ge .sSio.s alloy. Using a simple model similiar to that employed for dilute solid the dependence upon compo-sition over the entire system of the critical growth rate for the onset of constiutional supercooling was calculated, and was .found to he in good agreement with the experimental results. THE recent discovery of the low thermal conductivity of Ge-Si alloys' at high temperatures has revealed that these alloys have high efficiencies for thermoelectric-power generation.', Therefore, a reliable method was needed for the preparation of homogeneous samples required for definitive measurements throughout this alloy system. Due to the low diffusion rates in the solid alloys, the segregated samples obtained by quenching a melt are not readily homogenized by annealing.475 However. isothermal solidification from a melt of constant composition can produce uniform material. Of the available semiconductor crystal-growth procedures, the zone-leveling technique6 applied to a complete solid-solution alloy system by Wang and Alexander' and by others provides a simple method of doing this. In the present work, the homogeneity and microstructure of zone-leveled alloys have been correlated with growth conditions, and the conditions for preparing homogeneous Ge-Si alloys have been established. This has provided insight into the solidification process of alloy semiconductors. EXPERIMENTAL PROCEDURE Sample Preparation. The Ge-Si alloy phase diagram4 shown in Fig. l(a) consists of a complete series of solid solutions. The zone-leveling technique used to prepare most of the samples consists of moving a zone of liquidus composition (C1) through charge material of the corresponding solidus composition (C,), as is illustrated in Figs. l(b) and l(c). To prepare the charge materials, high-purity germanium and silicon were pulverized in a steel hammer mill, cleaned magnetically, and melted together to make uniform chill castings. The zone leveling was carried out in a resistance-heated furnace similar to that of Mitrenin et al.' shown in Fig. 2. However, a few specimens of high silicon content were prepared by the Czochralski technique. The growth rate ranged from 3.5 x X6 to 1.2 X 10~3 cm-sec-'. Temperature gradients in the solid and in the melt were determined by recording the temperature as the molten zone passed over a Pt-Pt 13 pct Rh thermocouple contained in a small

Jan 1, 1965

By George S. Ansell, Thomas E. Davidson

It has been known for a considerable period of time that the ductility of even quite brittle materials can be enhanced if they are deformed under a superposed hydrostatic pressure of sufficient magnitude. The response of ductility to pressure, however, has been shown to vary considerably between materials. Prior work has shown that the effects of pressure upon the tensile ductility of Fe-C materials depend upon the amount, shape and distribution of the brittle cementite phase. In this current investigation, the effects of pressure upon the fracture mechanisms in a series of annealed and spheroidized Fe-C materials were examined. It was observed that the principal effect of pressure is to suppress void growth and coalescence, retard cleavage fracture and to enhance the ductility of cementite platelets in pearlite. Based upon the observed effects of pressure upon the fracture mechanisms, a proposed explanation for the enhancement in ductility by pressure and for the structure sensitivity of the phenomena is presented and discussed. THE effect of superposed pressure upon the tensile ductility of a variety of metals has been well documented.'-'' Some of the results from several investigators are summarized in Fig. 1 where tensile ductility in terms of true strain to fracture (ef) is plotted as a function of the superposed pressure. As can be seen, a pressure of sufficient magnitude can significantly enhance the ductility of metals. However, Fig. 1 also demonstrates that the response of ductility to pressure and the form of the ductility-pressure relationship varies considerably between materials. Several explanations have been offered for the observed enhancement in ductility by a superposed pressure. Although no experimental evidence was provided, Bridgman13 and Bobrowsky10 proposed that the observed effect was due to the prevention or healing of microcracks or holes. Bulychev et a1.14 observed that cracks and voids in initially prestrained copper were healed in the necked region of a tensile specimen upon further straining while under a superposed pressure. Also, pugh5 observed that large cavities were suppressed in copper fractured in tension while under pressure. A second proposal has been forwarded by Beresnev et at al.6 This proposal is based upon the hypothesis that a material fails in a brittle manner because the normal tensile stress reaches a critical value before the shear stress is of sufficient magnitude to cause plastic flow. Since a superposed hydrostatic pressure will increase the ratio of shear to normal tensile stress, a sufficiently high hydrostatic pressure should favor plastic flow while retarding brittle fracture. Galli15 reported that a superposed pressure shifts the ductile-brittle transition temperature of molybdenum. This was explained based upon the reduction of the normal tensile stress by the superposed pressure. Pugh5 explained the occurrence of the observed pressure induced brittle-to-ductile transition in zinc in the same manner. Davidson et al.12 proposed an explanation for the enhancement of ductility by pressure based upon the effects of pressure upon the stress-state-sensitive stages of various fracture propagation mechanisms. Basically, they proposed that pressure will retard cleavage and intergranular fracture by counteracting the required normal tensile stress or will suppress void growth. They observed suppression of intergranular fracture and void growth in magnesium by pressure. Davidson and .Ansell16 reported ductility as a function of pressure for a series of annealed and spheroidized Fe-C alloys. Fig. 2, from this prior work, demonstrates that the effect of pressure upon ductility is structure sensitive in terms of the amount, shape and distribution of the brittle cementite phase. As shown in Fig. 2, in the absence of cementite or when the cementite is in isolated particle form (spheroidized), the ductility-pressure relationship is linear and the slope decreases with increasing carbon content. In the annealed carbon-bearing alloys wherein the cementite is in the form of closely spaced platelets (pearlite) or in the form of a continuous network along prior aus-tenite boundaries (1.1 pct C material), ductility as a function of pressure is nonlinear (polynomial relationship) in which the slope increases with increasing pressure. At the highest pressures studied (22.8 kbars), the slope of the curves for these materials tends to approach those for the spheroidized material of the same carbon content. In this current investigation the change in fracture mechanisms as a function of pressure for the materials shown in Fig. 2 has been examined. The possible connection between the observed effects of pressure upon the fracture mechanisms and the effect of pressure upon ductility is discussed.

Jan 1, 1970

By D. A. Kraai, S. Floreen

The effect of 1 to 50 ppm S on the ductility of nickel at 800° to 1400°F was studied. Results at each temperature showed a decrease in the reduction of area from approximately 95 to 5 pet over the sulfur range studied. Ductility varied with grain size, but only to a minor extent relative to the sulfiw effect. The effects of sulfur were completely offset by the addition of small amounts of magnesium. The results indicate that the "hot-short" loss in ductility is not an inherent property of nickel. Some possible mechanisms which cause the loss in ductility are described. MANY metals or alloys that normally possess high ductility exhibit a ductility loss at intermediate temperatures. This loss in ductility is often called "hot-shortness". Numerous examples of this phenomenon have been reported in the literature. Much of this work has been reviewed by McLean1 and by Rhines and Wray.2 To date there is no fully satisfactory explanation of the cause of this intermediate-temperature hot-shortness. It is generally recognized that impurities, and particularly impurities that form low-melting phases, can cause embrittlement. Examples of hot-shortness have been reported, however, where there were no obvious impurities present which would lower the ductility. Thus there has been some basis for believing that hot-shortness is an inherent property, and that even the purest metal would display a hot-short loss in ductility. This latter hypothesis was recently put forward by Rhines and wray2 based on studies of nickel and nickel alloys. In the discussion of this paper, however, Guard noted that high-purity nickel showed no hot-shortness.3 Thus there is reason to doubt whether pure nickel, or by inference any other pure metal, will inherently exhibit hot-shortness. The present work was initiated to determine the extent to which hot ductility was sensitive to very small amounts of an impurity element. If it could be demonstrated that hot-shortness could be induced by only minor amounts of an impurity, then it might be argued that hot-shortness in general is an impurity effect, and not a fundamental property of pure metals. The particular impurity studied was sulfur in nickel. The deleterious effects of sulfur are well- known. It is also well-known, and will be shown below, that additions of magnesium will render sulfur innocuous. When no such refining agents are added, however, the Ni-S system is a very useful one for studying the influence of small amounts of impurities. EXPERIMENTAL PROCEDURE Two heats containing -24 ppm S were vacuum-melted and small amounts of magnesium were then added under an argon atmosphere. These alloys were used to show the effectiveness of the normal magnesium treatment in overcoming the influence of sulfur. A second series of alloys with a sulfur range of 1 to 50 ppm was then prepared by vacuum melting nickel in alumina crucibles. No elements, such as magnesium, which tend to combine with sulfur were added. The higher sulfur contents were attained by adding nickel sulfide. Lower sulfur contents were prepared using a method in which the melt was oxidized under vacuum to produce the reaction S + 2O = SO2 These heats were subsequently deoxidized with carbon. Ten- to twenty-pound ingots were cast of all of the alloys studied. The compositions are given in Table I. The ingots were forged and hot-rolled to 3/4-in. bar. They were then annealed at either 2000" or 1600°F to produce different grain sizes. One-quarter-in.-diam tensile specimens were machined from the bars. These were tested at 800°, 1000o, 1200°, and 1400°F. The specimens were held at temperature approximately 45 min before testing. The strain rates were 0.005 min-1 to yielding, and 0.05 min-' after yielding. No extensometers or gage marks were placed on the specimens because the higher sulfur heats tended to fracture at the knife-edge indentations or gage marks. The properties measured were ultimate tensile strength and reduction of area. The analytical technique for determining sulfur at low levels was that developed by Burke and Davis.4 They reported a standard deviation of 1 ppm at an average sulfur level of 4 ppm in NBS standards. A standard deviation of 3 ppm is probably more realistic for the alloys used in this investigation considering the possibility of some segregation in the ingots. RESULTS A summary of the tensile results is given in Table I. As shown in the table, both heats to which

Jan 1, 1964

By E. Teghtsoonian, K. G. Davis

THE preparation of cobalt crystals offers problems: on cooling through 400°C a phase transformation takes place whereby the structure changes from face-centered cubic to the low temperature close-packed hexagonal form. There are a few references in the literature which describe the preparation of cobalt crystals for magnetic work1,&apos; where melt-solidification methods were used. Reasons will be given why such methods were found unsuitable for our purposes. The following techniques were tried: 1) Solid state methods. Any mechanical shaping of tensile specimens would lead to uncertainty with regard to residual strains. With this in mind, following Kaa, strain-anneal and grain growth techniques were extensively investigated. In no Case were useful single crystals obtained. The transformation boundaries, which are crystallographically similar to twin boundaries, are probably extremely stable and inhibit the grain growth. 2) Growth from the melt. Normal melt-solidification methods were tried, using recrystallised alumina crucibles, and also a osoft moldo technique in which cobalt rod was packed in alumina powder. Trouble was encountered with gas evolution on solidification of the melt, giving porosity. Some adhesion of cobalt to the alumina also took place. Only a small proportion of the runs gave single crystals. 3) Zone-refining. Much the best results have been obtained using an electron-beam floating zone refiner. The refiner, based on a design by Calverly et Al .5 had a single-turn tungsten filament. It was operated at 600 v with an emission current around 45 ma. Commercial cobalt rod 1/8 in. in diam was given one pass at a rate of zone travel normally 25 cm per hr, under a vacuum approximately 10-5mm of Hg. Over 50 pct of the runs gave long sections of single crystal. Crystals up to 2o Cm long with good uniformity of cross section and straightness have been grown in this way. Increase in the length of the molten zone resulted in higher single-crystal yields, but control of zone stability was reduced. Sub-boundaries in the zoned crystals were few, and Laue X-ray spots were sharp. The success of the method is believed to lie in two factors, namely i) the absence of crucible restraints during the transformation, and ii) extreme axiality of heat flow during cooling. The axes of the zoned crystals were clustered around the [ 1010] pole, the pole of the basal plane being at least 60 deg from the specimen axis. Crystals grown at lower rates of zone travel showed the same orientation range, Fig. 1. This orientation is similar to that for other hexagonal metals grown from the melt, which is a little surprising when the mode of formation of the hexagonal phase is considered. The preferred orientation is probably caused by anisotropy of heat conduction, i.e., that crystal which can most effectively conduct heat away from the transformation interface will be favored. Fig. 2 shows the area on a standard cubic stereo-gram in which there are no poles more than 60 deg from one of the four < 111> directions. This area

Jan 1, 1962

By H. Papazian, Robert A. Lad

SINCE it can be shown both theoretically&apos;&apos; : and experimentally that disordered Cu3Au has a greater internal energy than the ordered alloy, it might be expected that its chemical reactivity would be greater. Experiments were initiated&apos; to test this hypothesis. This note will describe some recent results obtained in the study of the rates of corrosion of ordered and disordered polycrystalline Cu3Au by aqueous FeCl., The work of Robertson&apos; has indicated that the attack by such solutions is intergran-ular and highly orientation dependent. It was of interest to see whether the order-disorder effect was great enough to overcome the variations from specimen to specimen which would arise from this type of attack. The polycrystalline alloy specimens (0.020 in. wire, 1¾ in. long) were preannealed in ½ atm H, at 700°C for 2 hr. The subsequent heat treatments to produce order and disorder were performed in M atm He. Disordered specimens were obtained by heating at 450°C for 2 hr and quenching in water. Ordered specimens were produced by heating for 2 hr at 450°, furnace cooling to 380°, and soaking at 380°C for 80 to 90 hr. Room temperature was reached by cooling to 150" at a rate never exceeding 7" per hr, and water quenching from 150°C. The specimens so produced exhibited electrical resistivities characteristic of the two states; of the order of 11.27x10 ohm-cm for the disordered, and 4.28x10 ohm-cm for the ordered specimens. The corrosion rates were studied at 30°C in ferric chloride solutions of several concentrations (?,¼, 1.5, and 1 molar). The specimens were attached to a stirrer during the tests. Tests were interrupted at intervals, and the specimen weight change was determined after washing and drying. Analysis of the solutions showed that the attack was limited to the copper. The higher corrosion rate for the disordered alloy, as illustrated in Fig. l, is typical of the results obtained. The effect of variation in ferric chloride concentrations is indicated in Table I for typical specimens. The variations in the ratio of reactivity for disordered and ordered specimens at the different concentrations are within experimental error, and the best value is estimated to be near 1.4. The experimental variation was due in part to the mode of attack, as mentioned, and in part to the fact that films were formed on the specimens under some conditions. Electron diffraction patterns of the films were very complex and indicated the presence of metallic iron, as did chemical analysis. In an attempt to eliminate the difficulties arising from the mechanism of attack, single crystal specimens were used. A greater reaction rate was again measured for the disordered specimens, but the reproduci-bility was no better than that for the polycrystalline metal. This would indicate that film formation was primarily responsible. It was concluded that the reaction with aqueous ferric chloride served to demonstrate that the reactivity of disordered Cu3Au is greater than that of the ordered alloy. However, the difficulties with film formation did not permit determinations of a precision great enough to warrant extension of the study to partially ordered alloy systems.

Jan 1, 1957